Table of Contents
Advertisement
Quick Links
INSTALLATION INSTRUCTIONS FOR PART 95-2009
95-2009
KIT FEATURES
• Double DIN Radio Provision
• Stacked ISO Mount Units Provision
KIT COMPONENTS
• A) Double DIN Brackets • B) Double DIN Trim Plate • C) Spacers • D) (4) Carriage Bolts
• E) (4) Kep Nuts • F) (3) Screws-(3) Speed Clips
A
E
1-800-221-0932
© COPYRIGHT 2004-2009 METRA ELECTRONICS CORPORATION
APPLICATIONS
GM/SUZUKI
MULTI KIT
B
WIRING AND ANTENNA CONNECTIONS
(Sold Separately)
• Wiring Harness - Please see www.metraonline.com
F
• Antenna Adapter -
• 40-GM10 - GM Antenna Adapter 1988-up
• 40-CR10 - Chrysler Antenna Adapter 2002-up
TOOLS REQUIRED:
Utility knife • Phillips Screwdriver • Socket Set
C
for specific interface applications
www.metraonline.com
D
Advertisement
Table of Contents
Related Manuals for Metra Electronics 95-2009
Summary of Contents for Metra Electronics 95-2009
- Page 1 INSTALLATION INSTRUCTIONS FOR PART 95-2009 GM/SUZUKI MULTI KIT 95-2009 KIT FEATURES • Double DIN Radio Provision • Stacked ISO Mount Units Provision KIT COMPONENTS • A) Double DIN Brackets • B) Double DIN Trim Plate • C) Spacers • D) (4) Carriage Bolts •...
-
Page 2: Table Of Contents
Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow. 95-2009 HUMMER ISUZU Ascender Amigo I-290/I370... -
Page 3: Century
Unclip the entire dash trim bezel and remove. Open doors and unsnap end caps from each side of dash. Unsnap and remove radio/instrument cluster panel. Remove (3) screws in order to remove radio. Continue to kit assembly. 95-2009 DASH DISASSEMBLY... -
Page 4: Le Sabre
Pop out the a/c vents and remove (1) Phillips screw exposed in each vent cavity. Unclip the radio trim bezel and remove. Remove the screws securing the fac- tory head unit and disconnect the wiring. Continue to kit assembly. 95-2009 DASH DISASSEMBLY... -
Page 5: Dash Disassembly
Unsnap and remove trim along center of dash. (One piece on right and one on left of wheel) Unsnap and remove radio/instrument bezel. Remove (2) screws in order to remove radio. Continue to kit assembly. 95-2009 DASH DISASSEMBLY... -
Page 6: Rendezvous
Remove liners from cup holders and storage pocket next to cup holders, then remove screws. Unsnap and remove panel. Remove (2) screws from bottom of radio/climate control bezel, unclip and remove. Remove (3) 9/32" hex head screws to remove radio. Continue to kit assembly. 95-2009 DASH DISASSEMBLY... -
Page 7: Riviera
Remove (3) Phillips screw to remove climate control. Remove (2) Phillips screws to remove rear support and (3) 9/32" hex head screws to remove radio. Continue to kit assembly. 95-2009 DASH DISASSEMBLY... -
Page 8: Roadmaster
Remove (2) 7mm screws above instrument cluster. Set parking brake, turn car on, and move shifter to the lowest gear. Tilt steering wheel down then unsnap entire instrument cluster/radio panel and remove. Remove (3) 7mm screws to remove radio. Continue to kit assembly. 95-2009 DASH DISASSEMBLY... -
Page 9: Skylark
(2) plastic panels by turning (2) 1/4 turn fasteners per side. Remove (4) 9/32" screws revealed. (2 per side). Unsnap panel from driver's side to passenger's side. Remove (3) 9/32" screws to remove radio. Continue to kit assembly. 95-2009 DASH DISASSEMBLY... -
Page 10: Avalanche
GMC • SIERRA 2003-2007 YUKON / DENALI / XL 2003-2006 Disconnect the negative battery terminal to prevent an accidental short circuit. Unsnap and remove dash bezel. Remove (3) 9/32" screws and remove radio. Continue to kit assembly. 95-2009 DASH DISASSEMBLY TAHOE 2003-2006... - Page 11 Remove (2) 7mm screws at the top of the radio/air conditioning bezel, then unclip panel and remove. Remove (4) 7mm screws that hold the radio in, slide radio out, unplug the radio harnesses and remove radio. Continue to kit assembly. 95-2009 DASH DISASSEMBLY CADILLAC • FLEETWOOD 1990-1996...
- Page 12 95-2009 DASH DISASSEMBLY CADILLAC • FLEETWOOD FLEETWOOD BROUGHAM 1990-1996 RADIO BRACKET DISASSEMBLY 1 Remove (4) 10mm nuts, (2) on top of the radio and (2) on the bottom of the radio, that hold the factory mounting brackets on. save brackets and nuts for kit...
-
Page 13: Eldorado
(CAUTION: Some models are equipped with bezels made of real wood. Remove (2) nuts securing the bottom of the factory head unit and discon- nect the wiring. Continue to kit assembly. 95-2009 DASH DISASSEMBLY SEVILLE 1992-1995... -
Page 14: Blazer
Remove (1) Phillips screw above the instrument cluster. Unclip the dash trim bezel and remove. Remove (2) 9/32" hex-head screws securing the factory head unit and disconnect the wiring. Continue to kit assembly. 95-2009 DASH DISASSEMBLY... -
Page 15: Cavalier
Remove (1) Phillips screw from the defroster duct. Remove the ductwork and (1) Phillips screw exposed. Remove the dash pad and (3) Phillips screws exposed at the top of the radio trim bezel. Continue to kit assembly. 95-2009 DASH DISASSEMBLY... -
Page 16: Colorado
Disconnect the negative battery terminal to prevent an accidental short circuit. Unsnap and remove the entire panel surrounding the radio and A/C controls. (Figure A) Remove (3) 9/32”screws securing the radio to remove. (Figure B) Continue to kit assembly. 95-2009 DASH DISASSEMBLY I-280/I-350 2006... - Page 17 Unsnap and remove small trim panel below steering column. Unsnap radio/climate/instrument panel. Move shift lever to first gear position. Rotate panel counterclockwise to lift over steering column and remove. Remove (3) 9/32" hex head screws to remove radio. Continue to kit assembly. 95-2009 DASH DISASSEMBLY...
- Page 18 Remove (2) 10mm nuts from inside center pocket between power outlets. Unsnap and remove radio and instrument cluster panel. (May not be necessary to completely remove radio and instrument cluster panel to access radio.) Remove (3) 9/32" bolts to remove radio. Continue to kit assembly. 95-2009 DASH DISASSEMBLY...
-
Page 19: Impala
Remove (2) Phillips screws from the knee panel. Unclip the knee panel and remove (1) phillips screw exposed on the right side of the steering column. Unclip and remove the entire dash trim bezel. Continue to kit assembly. 95-2009 DASH DISASSEMBLY... -
Page 20: Malibu
CHEVROLET • MALIBU 2001-2003 Disconnect the negative battery terminal to prevent an accidental short circuit. Unsnap and remove radio bezel. Remove (3) bolts and remove radio. Continue to kit assembly. 95-2009 DASH DISASSEMBLY MALIBU CLASSIC 2004... - Page 21 Unclip the radio trim bezel and disconnect the cigarette lighter wiring. Remove (2) screws securing each side of the factory head unit and (1) screw from the rear support. Slide the unit out and disconnect the wiring. Continue to kit assembly. 95-2009 DASH DISASSEMBLY...
-
Page 22: Monte Carlo
Unsnap the driver's side fuse panel cover and remove (1) 9/32" screw. Open the glove box and remove (1) 9/32" screw from the upper left corner. Remove (3) 9/32" screws securing the factory radio and disconnect the wiring. Continue to kit assembly. 95-2009 DASH DISASSEMBLY... - Page 23 Remove the (5) 9/32” screws securing the radio/instrument panel then unclip and remove the panel. (Figure D) Remove the screws securing the factory head unit and disconnect the wiring. Continue to kit assembly. 95-2009 DASH DISASSEMBLY 1 2 3 1 2 3...
-
Page 24: Tracker
Pull out on the climate control cluster and remove (2) screws exposed. Unclip the radio trim bezel. Remove (4) screws from the factory head unit, slide the unit out and dis- connect the wiring. Continue to kit assembly. 95-2009 DASH DISASSEMBLY XL-7 2001-2002... -
Page 25: Trailblazer
Remove (2) 7mm hex heads from under steering column and lower the panel. Remove (3) Phillips screws around steering wheel. Unsnap and remove bezel. (Use caution pulling over hazard switch.) Remove (3) 7mm hex head screws to remove radio. Continue to kit assembly. 95-2009 DASH DISASSEMBLY... -
Page 26: Venture
Remove the ashtray and (1) phillips screw exposed in the ashtray cavity. Remove (1) Phillips screw from the cigarette lighter compartment. Remove (2) Phillips screws securing the factory head unit and disconnect the wiring. Continue to kit assembly. 95-2009 DASH DISASSEMBLY... - Page 27 Remove the ashtray and (1) phillips screw exposed in the ashtray cavity. Remove (1) Phillips screw from the cigarette lighter compartment. Remove (2) Phillips screws securing the factory head unit and disconnect the wiring. Continue to kit assembly. 95-2009 DASH DISASSEMBLY...
-
Page 28: Bravada
95-2009 DASH DISASSEMBLY GMC • ENVOY 2002-2009 / ISUZU ASCENDER 2003-2009 OLDSMOBILE • BRAVADA 1998-2004 BUICK • RAINIER 2004-2007 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2. Remove (4) Phillips screws, (2) from left and (2) from right of carpeted panel. -
Page 29: Passport
Remove the ashtray and (1) Phillips screw exposed in the ashtray cavity. Unclip and remove the trim panel surrounding the factory radio. Remove (4) Phillips screws securing the factory radio and disconnect the wiring. Continue to kit assembly. 95-2009 DASH DISASSEMBLY... - Page 30 Unclip cup holder/shifter trim assembly and remove. Remove (6) Phillips screws from top of center console. Remove (2) Phillips screws from inside pocket on back of center console, then unclip and remove. Continued on page 30. 95-2009 DASH DISASSEMBLY...
- Page 31 Phillips screws from under console trimtop on passenger side. Slide control assembly rearwards. Remove (2) T-30 torx bolts from top of rado/climate control trim and unclip and remove. Remove (3) 9/32” screws that hold the radio in. Continue to kit assembly. 95-2009 DASH DISASSEMBLY...
-
Page 32: Achieva
Remove (10) torx-head screws from the glove box location. Remove (2) 9/32" hex-head screws under the steering column. Unclip the dash trim bezel. Remove the screws securing the factory head unit and disconnect the wiring. Continue to kit assembly. 95-2009 DASH DISASSEMBLY... -
Page 33: Alero
U-clip from front of shifter and pull upward. Unclip and remove shifter trim panel. Unclip and remove radio and climate control panel by pulling from bottom. Remove (3) 9/32" screws from radio and remove. Continue to kit assembly. 95-2009 DASH DISASSEMBLY... -
Page 34: Aurora
Disconnect the negative battery terminal to prevent an accidental short circuit. Unclip the radio trim bezel and remove the bezel. Remove (2) 7mm screws securing the factory head unit and disconnect the wiring. Continue to kit assembly. 95-2009 DASH DISASSEMBLY... -
Page 35: Cutlass Supreme
Disconnect the negative battery terminal to prevent an accidental short circuit. Unclip the radio trim bezel and remove. Remove (2) ) 9/32" hex-head screws securing the factory head unit and disconnect the wiring. Continue to kit assembly. 95-2009 DASH DISASSEMBLY... - Page 36 Remove (2) hex-head screws below the radio trim bezel. Lift up on the bezel and remove. Remove (3) Phillips hex-head screws securing the factory head unit and disconnect the wiring. Continue to kit assembly. 95-2009 DASH DISASSEMBLY EIGHTY EIGHT 1994-1999 NINETY EIGHT 1994-1996...
-
Page 37: Intrigue
(2) 9/32" hex-head screws exposed. Remove the center console. Unclip the radio trim bezel and remove. Remove (2) 9/32" hex-head screws securing the factory head unit and disconnect the wiring. Continue to kit assembly. 95-2009 DASH DISASSEMBLY... -
Page 38: Regency
Disconnect the negative battery terminal to prevent an accidental short circuit. Open glove box and remove two-center trim bezels attached by screws. Unsnap and remove radio trim bezel. Remove (3) 9/32" hex-head screws and remove radio. Continue to kit assembly. 95-2009 DASH DISASSEMBLY... -
Page 39: Aztec
Pull out cup holder inserts. Remove (1) Phillips screw exposed inside bottom cup holder. Unsnap and remove shifter trim with cup holders. Remove (2) #15 torx at bottom of radio/climate bezel. Continue to kit assembly. 95-2009 DASH DISASSEMBLY... -
Page 40: Bonneville
Remove (2) Phillips screws from the instrument cluster. Unclip the ignition trim and remove. Unclip the climate control/radio trim bezel and remove. Depress the spring clips on each side of the factory head unit and remove. Continue to kit assembly. 95-2009 DASH DISASSEMBLY... -
Page 41: Grand Am
PONTIAC • GRAND AM 2001-2005 1 Disconnect the negative battery terminal to prevent an accidental short circuit. Unsnap and remove radio trim bezel. Remove (3) 9/32” screws from radio brackets and remove radio. Continue to kit assembly. 95-2009 DASH DISASSEMBLY... -
Page 42: Sunfire
Open the glove box and remove (2) Phillips screws exposed on the right edge of the radio trim bezel. Unclip the bezel and remove. Remove (2) 7mm hex-head screws securing the factory head unit and disconnect the wiring. Continue to kit assembly. 95-2009 DASH DISASSEMBLY... - Page 43 Unclip the bottom edge of the radio trim panel then lift up and out to remove. (Figure A) Remove (4) 10MM bolts securing the factory radio. (Figure B) Continue to kit assembly. 95-2009 DASH DISASSEMBLY...
- Page 44 1 Disconnect the negative battery terminal to prevent an accidental short circuit. Unclip the dash trim bezel and remove. Remove (4) Phillips screws securing the factory head unit and disconnect the wiring. Continue to kit assembly. 95-2009 DASH DISASSEMBLY SUZUKI • AERIO 2002...
- Page 45 Remove the climate control knobs. Remove (1) Phillips screw located above the radio opening. Unclip the radio trim bezel. Remove (4) screws from the factory head unit, slide the unit out and dis- connect the wiring. Continue to kit assembly. 95-2009 DASH DISASSEMBLY...
-
Page 46: Fleetwood/Broughham
Cut tabs highlighted on both sides of both brackets. (Figure A) CHEVY Tracker/METRO/SUZUKI. Cut tabs highlighted on both sides of both brackets. (Figure B) CADILLAC Fleetwood/Broughham. Cut all tabs highlighted on both sides of both brackets. (Figure C) Continued on page 46. 95-2009 TAB INSTRUCTIONS... -
Page 47: Vibe
Cut (4) tabs highlighted on double DIN trim plate. (Figure H) CADILLAC Eldorado/Seville. Cut tabs highlighted on double DIN brackets. (Figure F) Cut (1) tab highlighted on top left corner of double DIN trim plate. (Figure G) Continue to final assembly. 95-2009 TAB INSTRUCTIONS... - Page 48 95-2009 KIT ASSEMBLY CADILLAC • FLEETWOOD 1990-1996 FLEETWOOD BROUGHAM KIT ASSEMBLY WITH FACTORY BRACKETS 1 Using carriage bolts and Keps nuts supplied, mount the factory brackets to the double DIN trim plate/double DIN bracket assembly, keeping in mind which bracket is top and which one is bottom.
-
Page 49: Kit Assembly
1 Disconnect the negative battery terminal to prevent an accidental short circuit. Align the tabs on the bottom of the double DIN trim plate with notches in sub dash. Secure with the (2) Carriage bolts and (2) Kep nuts provided. Continue to kit assembly. 95-2009 KIT ASSEMBLY SEVILLE 1992-1995... -
Page 50: Double Din Radio Provision
Oldsmobile Aurora and the Pontiac Bonneville the (3) speed clips and screws provided with the kit will need to be installed into the sub dash where the screw holes line up on the kit. Continue to final assembly. 95-2009 KIT ASSEMBLY... -
Page 51: Final Assembly
Dimmer ....Orange / White *NOTE: When a Black wire is not present, ground radio to vehicle chassis. All colors may not be present on all leads due to manufacturer’s specifications. 95-2009 FINAL ASSEMBLY (A) Strip wire ends back 1/2" B) Twist ends together... - Page 52 95-2009 INSTRUCTIONS 1-800-221-0932 www.metraonline.com REV. 04/15/09 © COPYRIGHT 2004-2009 METRA ELECTRONICS CORPORATION INST95-2009...