Ide Configuration - Asus 1U Rackmount Barebone Server RS120-E3 (PA4) User Manual

5.3.4 5.3.4 5.3.4

IDE Configuration

IDE Configuration IDE Configuration
5.3.4 5.3.4 IDE Configuration IDE Configuration
The items in this menu allow you to set or change the configurations for the
IDE devices installed in the system. Select an item then press <Enter> if you
want to configure the item.
(Defaults)
Main
IDE Configuration
ATA/IDE Configuration
Configure SATA As
Primary IDE Master
Primary IDE Slave
Secondary IDE Master
Secondary IDE Slave
Third IDE Master
Third IDE Slave
Fourth IDE Master
Fourth IDE Slave
IDE Detect Time Out (Sec)
v02.58 (C)Copyright 1985-2004, American Megatrends, Inc.
ATA/IDE Configuration [Enhanced] ATA/IDE Configuration [Enhanced] ATA/IDE Configuration [Enhanced]
ATA/IDE Configuration [Enhanced] ATA/IDE Configuration [Enhanced]
Allows selection of the IDE operation mode depending on the installed operating
system (OS). Set to [Enhanced] mode if you are using native OS, e.g. Windows
Server 2000/2003. Set to [Compatible] mode if you are using legacy OS,
e.g. Windows ME/98/NT, MS-DOS. Configuration options: [Disabled]
[Compatible] [Enhanced]
Configure SATA As Configure SATA As
The Configure SATA As Configure SATA As Configure SATA As and Third IDE Master/Slave
only when you set the ATA/IDE Configuration to [Enhanced] mode.
Configure SATA As [IDE]
Sets the configuration for the Serial ATA connectors supported by the
Southbridge chip.
If you want to use the Serial ATA hard disk drives as Parallel ATA physical
storage devices, set this item to [IDE].
Set this item to [RAID] if you want to create a RAID volume from Serial
ATA hard disk drives.
Place a jumper cap on pins 1-2 of the R A I D _ S E L 1
Logic Embedded SATA RAID Utility (for RAID 0, RAID 1, or RAID 0+1
configuration; supported on Windows
Hat ® Enterprise ver. 3.0). Refer to section 4.2 Jumpers
Place a jumper cap on pins 2-3 of the RAID_SEL1
Matrix Storage Manager (for RAID 0, RAID 1, RAID 0+1, or software RAID 5
configuration; supported on Windows
A S U S R S 1 2 0 - E 3 / P A 4 A S U S R S 1 2 0 - E 3 / P A 4 A S U S R S 1 2 0 - E 3 / P A 4
A S U S R S 1 2 0 - E 3 / P A 4 A S U S R S 1 2 0 - E 3 / P A 4
BIOS SETUP UTILITY
[Enhanced]
[IDE]
: [ATAPI CD-ROM]
: [Not Detected]
: [Not Detected]
: [Not Detected]
: [Not Detected]
: [Not Detected]
: [Not Detected]
: [Hard Disk]
[35]
Third IDE Master/Slave Third IDE Master/Slave
Third IDE Master/Slave items appear Third IDE Master/Slave
R A I D _ S E L 1 R A I D _ S E L 1
R A I D _ S E L 1 jumper to use the LSI R A I D _ S E L 1
®
RAID_SEL1 RAID_SEL1 RAID_SEL1 jumper to use the Intel RAID_SEL1
® 2000/2003 Server/XP).
Set[Compatible Mode]
when Legacy OS(i.e.
WIN Me, 98, NT4.0, MS
DOS)is used.
Set[Enhanced Mode]
when Native OS(i.e.
Win2000, WIN XP)is
used.
Select Screen
Select Item
+- Change Option
F1 General Help
F10 Save and Exit
ESC Exit
2000/2003 Server/XP and Red
4.2 Jumpers 4.2 Jumpers 4.2 Jumpers for details. 4.2 Jumpers
®
®
5 - 1 5 5 - 1 5 5 - 1 5
5 - 1 5 5 - 1 5