Mesa/Boogie MARK 1 RE-ISSUE Owner's Manual page 26

ON TRIODES, PENTODES & IRISHMENT: (Continued) Thus a diode tube - one with a cathode and an anode - is mostly used to
rectify alternating current into direct current by passing it without restriction, but in one direction only. This also explains why closing
time is stricly enforced at Irish pubs: During normal operation, the traffic flow is similarily unimpeded and uni-directional toward the bar
and this process rectifies the work-day negativity. It goes without saying that no one leaves as long as the atmosphere around the bar
remains positively charged.
TRIODES:
This section is a continuing technical treatise on the workings of Irish Pubs but to make it easier for the layman to understand, it is
explained in terms of vacuum tube technology. Enter the original bar - free beer and no doors. Well, it turns out that some control over
the flow can be a necessary and useful advantage. This led to the invention of those swinging louvered saloon doors which are open
at the top and bottom. They are patterned after the control grid of the vacuum tube, which is a loosely wound coil of thin wire located
between the cathode and the plate.
In a Triode the plate is always positively charged with high voltage D.C. and even though the grid is blocking the path, those negative
electrons can still FEEL the strong attraction - just as the Irishmen can see in through the louvers of the bar doors. They know what
pleasures lie beyond, but to get there requires overcoming the negative influences controlling the access. This negative influence is
typically called a Bias. In electronic terms that means the grid is supplied with a voltage which is slightly MORE NEGATIVE than the
already negative electrons. The more negative the Bias, the more it tends to neutralize the attraction of the plate and repel the
electrons back toward the cathode.
The Irish can be similarily charged with Bias, but unless you are Irish yourself, this type of Biasing may be more difficult to understand.
The effect is similar though: The more negative the Bias, the more it impedes forward progress. Generally speaking though, the
electronic Bias of the grid is easiert to overcome, and for two main reasons: First, the Bias is set - like the bar doors - to allow some
passage. Second, the grid is mostly NOT THERE, like the louvered doors which are mostly open spaces. Unlike the plate which is
solid, the grid is like a coiled bed spring. It can create a repelling field but mostly it's empty space in between widely seperated
windings of wire. It's very easy to control the electrons as they pass through the grid's force field: Changing the grid voltage only
slightly will have an enormous effect on how much current flows through... and that's what AMPLIFICATION is: a small change in
voltage at the grid causing a large change in current flowing to the plate.
The purpose of the louvered bar doors is similar to that of the grid, namely, to give momentary pause while still revealing the promise
within. Hesitation mostly gives way to temptation, but there are those few stalwart Irishmen who think twice and decide to come back
later. Most just pause slightly then go on through. That is the purpose of the bar doors: to prevent everyone from crowding in all at
once - and as the door is made less of a barrier, wider spaces between the louvers, more of the bar's attractive influence is felt outside
thus amplifying the customer flow and increasing the crowd at the bar.
PENTODES:
Occasionally though, bar doors - even the louvered type - were found to be too effective, and too many customers turned away.
Something further was needed to increase the attraction of the bar and overcome the resistance created by the door. Thus the
cocktail waitress was invented.
Once again the idea was inspired by the vacuum tube. It had been discovered in some tubes, often large power types, that the
distance to the plate was too great to attract enough electrons past the negative influence of the control grid. So another grid coil of
fine wire was inserted between the first grid and the plate. This was called the screen grid and carrying a highly positive charge, it
functioned as a "bait" for the plate.
In a properly designed power tube such as an EL84 or a 6V6, the windings of the screen grid are precisely aligned to fall in the shadow
of the control grid. This way the electrons responding to the pull of the screen grid are lined up in sheets as they pass between
windings of the inner control grid... only to find that they have been fooled! Once past the control grid and drawn toward the screen
grid, they discover...there's almost nothing there. The path they're on has them aligned to zing straight through the spaces BETWEEN
screen grid windings. So rather than a close and personal encounter, they just fly on past - and once they're out that far, there's no
PAGE 22