Integrated Amplifier MA6300 Owner’s Manual McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, New York 13903-2699 Phone: 607-723-3512 FAX: 607-724-0549...
The lightning flash with arrowhead, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “danger- ous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. WARNING - TO REDUCE RISK OF FIRE OR ELECTRICAL SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO...
Phone: 607-723-1545 Fax: 607-724-0549 Customer Service If it is determined that your McIntosh product is in need of repair, you can return it to your Dealer. You can also return it to the McIntosh Laboratory Service Department. For assistance on factory repair return procedure, contact the McIntosh Service Department at: McIntosh Laboratory, Inc.
Connector and Cable Information XLR Connectors Below is the Pin configuration for the XLR Balanced Input Connectors on the MA6300. Refer to the diagram for con- nection: PIN 1: Shield/Ground PIN 2: + Output PIN 3: - Output PIN 2...
Dimensions The following dimensions can assist in determining the best location for your MA6300. There is additional in- formation on the next page pertaining to installing the MA6300 into cabinets. Front View of the MA6300 Rear View of the MA6300...
Installation The MA6300 can be placed upright on a table or shelf, standing on its four feet. It also can be custom installed in a piece of furniture or cabinet of your choice. The four feet may be removed from the bottom of the MA6300 when it is custom installed as outlined below.
Rear Panel Connections Connect the MA6300 power cord to a live AC outlet. Refer to information on the back panel of your MA6300 to determine the correct voltage for your unit...
2. Connect a Control Cable from the McIntosh SACD/CD Player Power Control Out Jack to the Power Control In jack on the McIntosh Tuner. 3. Connect a Control Cable from the MA6300 CD1 DATA PORTS Jack to the McIntosh SACD/CD Player Data In Jack.
CD Player connected to the CD2 INPUTS may be used instead of the Balanced CD1 Inputs. 2. Connect an Audio Cable from a McIntosh Tuner 1 Fixed Outputs to the MA6300 TUNER INPUTS. 3. Connect an Audio Cable from a Turntable to the PHO- NO INPUTS and the Turntable Ground Connection to the GND grounding post.
3. Connect the MA6300 Power Cord to a live AC outlet. Figure 2 Figure 3 terminal. Refer to figure 7. Note: Banana Plugs are for use in the United States and Canada only.
Page 11
How to Connect Loudspeakers McIntosh Loudspeaker McIntosh Loudspeaker To AC Outlet...
How to Connect an external Power Amplifier The MA6300 has the ability to be connected to an exter- nal Preamplifier and/or Power Amplifier. In the example below, the MA6300 is connected to an external McIntosh Power Amplifier and to a McIntosh Loudspeaker with Bi-amplifer connections.
Front Panel Displays, Controls, Push-buttons and Jack IR Sensor receives commands from a Remote Control Standby Power On Indicator STANDBY/ON Push-button switch- es the MA6300 ON or OFF (Standby) and resets the micro- processors...
2,000Hz tone burst. Read the Upper Meter Scale if the Loudspeakers connect- ed to the MA6300 are of 8 Ohm Impedance and the Lower Meter Scale if they are 4 Ohms. Power Guard...
Page 15
STANDBY/ON Push-button. 3. When the STANDBY/ON LED is illuminated press the STANDBY/ON Push-button, the MA6300 will resume normal operation. Note: This can be performed with the MA6300 On or in the Standby Mode. How to Operate the MA6300, con’t Figure 9 Note: For an explanation of the Remote Control Push-button functions, refer to pages 16 and 17.
The Pause Push-button is also used as an Enter Push-button with some McIntosh compo- nents Acc On Press ACC ON to turn the power ON to a McIntosh Disc Player. Acc Off Press ACC OFF to turn the power OFF to a McIntosh Disc...
120 Volts, 50/60Hz at 3.2 amps 220 Volts, 50/60Hz at 1.8 amps 230 Volts, 50/60Hz at 1.8 amps 240 Volts, 50/60Hz at 1.8 amps Note: Refer to the rear panel of the MA6300 for the correct voltage. Overall Dimensions Width is 17-1/2 inches (44.45cm) Height is 7-5/8 inches (19.37cm) including feet...
If a shipping carton or any of the interior part(s) are needed, please call or write Customer Service Department of McIntosh Laboratory. Refer to page 3. Please see the Part List for the correct part numbers.
Page 20
McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, NY 13903 The continuous improvement of its products is the policy of McIntosh Laboratory Incorporated who reserve the right to improve design without notice. Printed in the U.S.A. McIntosh Part No. 04098900...
Need help?
Do you have a question about the MA6300 and is the answer not in the manual?
Questions and answers