Dust
Gollector
OPERATING INSTRUCTIONS
& PAFITS LIST
Read inslructions carefully betore attempting to assemble, inslall, operate, move, inspecl or seruice your dust cottector!
Betain insvuctions for luture reference,
High voltage electical power can
cause aeverc injury or death.
Always disconnect or lock out lrom power source anc!
let motor come to a complete stop belore inspecting,
movlng or seruicing.
Description
These dust co leclors are desgned to help malntain clean,
sale conditions around dusl creating machines in workshops
and lactories. The flexible hose incllded wilh each unit can be
hooked directly onlo lhe dusr creating machine. See page 7 for
exhausl volumes required for dillerent applications,
None of thes€ Dust Collectors are
designed lo collect any reactive metal
duslguch as Atuminum, Magnesium, Tantalum, Titanium
or Zirconium, Collecling lhese materials can result in a
severe explosion an(Uor fke resulling in death, severe
personal injury and ertensive property damage. Consult
the National Fire Protection Associatlon (NFPA) for NFPA
484; "Standard for Combustible Metals, lMetal Powderc,
and Metal Dusts,2002 Edilion". Also, contact your local
Fire DeDarlment tor assislance.
Not designed lo be used on a syslem Gquiring high static
pressure. Avold ducts sma ler than 3' diameter as they require
high slatic pressurc and restricl a r movemenl.
Do not use to collecl hot meral dusti plaslic and cloth parts
can be igniled.
Unpacking
Ca.lon musl be in uprighl position before opening. Inspect for
shipping damage and advise carrier immediately il damaged.
Check parts listlor missing or darnaged parts.
General Satety Information
Fead inslruclons cafefully before attempling lo assemble,
install, operate, move, inspect or service yo!r dust collectorl
Retain this rnanualfor future reference.
(l l
A WARI{I]{G
Hlgh speed rotating equiryent can
cause severc personal injury. Do
not opeate the collector unless the filEr bag is
attacheclj high speed dust partcles exiting frcm the
blower outlet can cause severe eye alamage anal
blin.lness. Guaftls must always be in place. Disconnect
or lock out trcm oower source an.l let motor come to a
complete stop betore inspecting, moving or servicing,
1. Follow all local elecl cal and safetv codes. as wett as
Nalional EleclricalCodes (NEC). National F re Proleclion
Associalion (NFPA) slandards and Occupauonal Safety
and Health Act (OSHA). All electical conneciions and
wiring should be performed only by qualiJed personnel.
2. l\,,lake sure ihe oower sdurce conlorrns to the
requirements ol your dusl colleclor motor
3. Exercise caution when the un t is in ooeration.There is a
h€h speed blower wheel nside ihe blower housing and
anolhef on the lop of lhe molor. Both can amputate
iingers of grab loose clolhing or necklies. Always wear
salety glasses when operaling ihe dusl collector
4. THESE DUST COLLECTORS ARETOP HEAVY, AND
CAN 8E OVERTURNED IF BUMPED OB NOT PLACED
ON A CLEAN LEVEL SUBFACE.
t2)
(3)
I\,laximum CFM al0' S.P. (c ean drum, dust bag and with
5 Jeel of nlel hose).
l\,4aximum
addilional static pressure ai which point there
lvlinimum micron size that slandad dust bag wittcaplure,
(4) See Speclfic Features For Each l\,,lodel" in catalog.
(5) Slarting amps are approximately 6-7 times the lullload
amps. High vollage amps are 1/2 of low vo tage amps. Amp
loads shown above are approxlmale and vary wilh differcnt
ACE IilDASTilAL PBODUCTS
5043 FARLIN AVE. .
3r4.385.5178
sT. LOU|S, MO.63115
FAX: 314.385.3254
Specifications
H P
CFM
0 )
Max.
s.P.
\2)
dBA
@
5 FT.
Slandard Dusl Bag
Blower
DIa.
Max.
Drum
Dia. (4)
Full load amps (5)
S hi p
Fab c
(sq. Fl.)
Micron
(3)
115 Voll
I Phase
230 Voll
3 Phase
335
3
76
Cotlon
Saleen
1 2. 5
1 0
8'
3"x 60'
20'
5.8
1. 8
32
450
7A
1 2 .5
1 0
4"x 60'
20'
6.8
1. 9
4a
580
7
7A
1 2. 5
1 0
10 5/s'
4'x 60'
20'
8. 8
2.4
53
700
83
Knil
1 8_ 0
5
5 x 6 0 '
72
475
61/ , '
7 6
1 8. 0
5
l l
6 x 6 0
24'
16. 0
85
2
1 100
A1l2'
1 8. 0
5
121/a
6 x 6 0
24',
20.o
5. 6
97
3
1300
10'
a4
Selecl oversized bag
lrom Pages 5 and 6.
13',
6"x 60'
24',
Nol
avallable
1. 6