Vertex Standard VX-1700 Series Service Manual
  1. Manuals
  2. Brands
  3. Vertex Standard Manuals
  4. Radio
  5. VX-1700 Series
  6. Service manual

Vertex Standard VX-1700 Series Service Manual

Hf multi mode mobile radio
Hide thumbs Also See for VX-1700 Series:
Table of Contents

Advertisement

Quick Links

See also: Reference Book , Operating Manual
VX-1700 Series
HF Multi Mode Mobile Radio
Service Manual
For USA Version
©2011 VERTEX STANDARD CO., LTD.
Introduction
This manual provides the technical information necessary for servicing the VX-1700 HF Transceiver.
Servicing this equipment requires expertise in handing surface-mount chip components. Attempts by non-
qualified persons to service this equipment may result in permanent damage not covered by the warranty, and
may be illegal in some countries.
Two PCB layout diagrams are provided for each double-sided board in this transceiver. Each side of the board
is referred to by the type of the majority of components installed on that side ("Side A" or "Side B"). In most
cases one side has only chip components (surface-mount devices), and the other has either a mixture of both
chip and leaded components (trimmers, coils, electrolytic capacitors, ICs, etc.), or leaded components only.
As described in the pages to follow, the advanced microprocessor design of the VX-1700 Transceiver allows a
complete alignment of this transceiver to be performed without opening the case of the radio; all adjustments
can be performed from the front panel, using the "Alignment Mode" menu.
While we believe the information in this manual to be correct, VERTEX STANDARD assumes no liability for
damage that may occur as a result of typographical or other errors that may be present. Your cooperation in
pointing out any inconsistencies in the technical information would be appreciated.
Specifications ...................................................................................................................................................... 2
Exploded View & Miscellaneous Parts .......................................................................................................... 3
Block Diagram ..................................................................................................................................................... 5
Connection Diagram .......................................................................................................................................... 6
Circuit Description ............................................................................................................................................. 7
Connector Pinout Diagrams ........................................................................................................................... 10
Alignment .......................................................................................................................................................... 11
ALE-1 Automatic Link Establishment Unit Installation ........................................................................... 19
CE77 PC Programming Software ................................................................................................................... 21
Board Units (Schematics, Layouts & Parts)
MAIN Unit .................................................................................................................................................. 49
PA-2 Unit ..................................................................................................................................................... 77
PANEL Unit ................................................................................................................................................ 91
GPS-INTERFACE Unit .............................................................................................................................. 97
MIC Unit .................................................................................................................................................... 107
ENC Unit ................................................................................................................................................... 108
ALE Unit (Option) .................................................................................................................................... 109
VERTEX STANDARD CO., LTD.
4-8-8 Nakameguro, Meguro-Ku, Tokyo 153-8644, Japan
VERTEX STANDARD
US Headquarters
10900 Walker Street, Cypress, CA 90630, U.S.A.
YAESU UK LTD.
Unit 12, Sun Valley Business Park, Winnall Close
Winchester, Hampshire, SO23 0LB, U.K.
VERTEX STANDARD HK LTD.
Unit 1306-1308, 13F., Millennium City 2, 378 Kwun Tong Road,
Kwun Tong, Kowloon, Hong Kong
VERTEX STANDARD AUSTRALIA PTY., LTD.
Tally Ho Business Park, 10 Wesley Court, East Burwood, VIC, 3151
EC051H95E
Contents
1

Advertisement

Table of Contents
loading

Related Manuals for Vertex Standard VX-1700 Series

Summary of Contents for Vertex Standard VX-1700 Series

  • Page 1: Table Of Contents

    “Alignment Mode” menu. While we believe the information in this manual to be correct, VERTEX STANDARD assumes no liability for damage that may occur as a result of typographical or other errors that may be present. Your cooperation in pointing out any inconsistencies in the technical information would be appreciated.

  • Page 2: Specifications

    Specifications General Receiver Frequency Range: 30 kHz ~ 30.0000 MHz Transmitter Frequency: 1.600 ~ 30.0000 MHz Emission Modes: A1A (CW), J3E (LSB/USB), A3E (AM), J2B (USB/LSB) Frequency Synthesizer Step: 10 Hz, 100 Hz, 1 kHz Frequency Stability: ±1 ppm (Typical) Operating Temperature Range: 14°...

  • Page 3: Exploded View & Miscellaneous Parts

    Exploded View & Miscellaneous Parts RA0695200 COVER (TOP) RA0809600 SPONGE RUBBER RA0809600 SPONGE RUBBER P1091335 CONNECTOR (FM-MDR-MI) PA UNIT RA0809600 SPONGE RUBBER RA0809600 SPONGE RUBBER RA0695600 RA0635400 HOLDER PLATE (CW) CHASSIS T9207202A WIRE ASSY PANEL UNIT RA0695700 HOLDER PLATE (D-SUB) RA069610A REFLECTOR SHEET RA0727200...
  • Page 4 Exploded View & Miscellaneous Parts Note...

  • Page 5: Block Diagram

    Block Diagram...

  • Page 6: Connection Diagram

    Connection Diagram...

  • Page 7: Circuit Description

    Circuit Description Receive Signal Path The DSP IC Q1035 (UPD77115) outputs AGC data which is proportionate to the received signal strength Incoming RF signal from the ANT jack is delivered to the main CPU Q1018 (HD64F2134). The main CPU to the PA Unit, and passes through the TX/RX relay Q1018 (HD64F2134), in turn, outputs a DC voltage RL2009 to J2006.

  • Page 8: Pll Circuit

    Circuit Description On the PA Unit, the low-level RF signal from the IC Q1056 (ADF4001BRU), which contains a refer- MAIN Unit is amplified by pre-driver Q2001 ence divider, serial-to-parallel data latch, program- (RD06HHF1), push-pull driver Q2008/Q2009 (both mable divider, phase comparator and a swallow RD16HHF1), and push-pull final amplifier Q2012/ counter.
  • Page 9 Circuit Description Control Circuit TX/RX Control Major frequency control functions such as channel When the PTT switch is pressed, pin 21 of the main selection, display, and PLL divider control are per- CPU Q1018 (HD64F2134) goes low, which causes formed by main CPU Q1018 (HD64F2134) on the pin 60 of the main CPU Q1018 (HD64F2134) to go MAIN Unit, at the command of the user via the tun- low.

  • Page 10: Connector Pinout Diagrams

    Connector Pinout Diagrams MIC Jack GPS Jack ( As Viewed From Front Panel ) ( As Viewed From Rear Panel ) Connected with , and GPS Data Input. P ENB N/C (Lot. 1~25) CNTL GND GPS Data Output (Lot. 26 & 27 : When the firmware is updated.

  • Page 11: Alignment

    ANT jack in all procedures alignment are not covered by the warranty policy. that call for transmission, except where specified Also, Vertex Standard reserves the right to change otherwise. Correct alignment is not possible with an circuits and alignment procedures in the interest of antenna.

  • Page 12: Pll Alignment

    Alignment Reference & Local Alignment Whenever possible, alignments should be made with oscillator shields and circuit boards firmly affixed PLL R EFERENCE REQUENCY LIGNMENT in place. Also, the test equipment must be thoroughly Connect the Frequency Counter to pin 4 of Q1062 warmed up before beginning.

  • Page 13: Transmitter Alignment

    Alignment Transmitter Alignment Receiver Alignment TX IF C RX IF C OILS LIGNMENT OILS LIGNMENT Connect the 50 Ohm Dummy Load to the ANT Connect the RF Signal Generator to the ANT jack, jack. and connect the AF millivoltmeter to the EXT SP Remove the coaxial plug from J1002 on the MAIN jack.
  • Page 14 Alignment PA Unit Alignment RIVER ECTION DLING URRENT LIGNMENT Connect the 50 Ohm Dummy Load to the ANT RIVER ECTION DLING URRENT LIGNMENT jack. Connect the 50 Ohm Dummy Load to the ANT Remove the shorting-plug from J2004 on the PA jack.
  • Page 15 Alignment CM C INAL ECTION DLING URRENT LIGNMENT OUPLER ALANCE Connect the 50 Ohm Dummy Load to the ANT Connect the 50 Ohm Dummy Load and Inline jack. Wattmeter to the ANT jack, and connect the CW Remove the solder jumper which is connected keyer to the KEY jack.
  • Page 16 Alignment TX O Software Menu Alignment UTPUT OWER LIGNMENT Connect the 50 Ohm Dummy Load and Inline The ANT jack should be connected to a Dummy Load Wattmeter to the ANT jack. (in the case of transmission) or RF Signal Generator Referring to the Table below, press the [ ] / [ ] (in the case of reception).
  • Page 17 Alignment TX G REV ALC A LIGNMENT LIGNMENT Connect the 50 Ohm Dummy Load and Inline Connect the 150 Ohm Dummy Load (or three 50 Wattmeter to the ANT jack. Ohm Dummy Loads in parallel) to the ANT jack. Referring to the Table below, press the [ ] / [ ] Connect the AF Generator to pin 4 of the MIC jack, and adjust the AF Generator output level to key to recall each parameter listed, then key the...
  • Page 18 Alignment Note...

  • Page 19: Ale-1 Automatic Link Establishment Unit Installation

    ALE-1 Automatic Link Establishment Unit Installation Installation Make sure that the transceiver off. Remove the DC Power Cable, Microphone, and Antenna from the transceiver. Referring to Figure 1, remove the four screws from the side of the transceiver (two screws for each side), along with four screws affixing the bottom case;...
  • Page 20 ALE-1 Automatic Link Establishment Unit Installation Note...

  • Page 21: Ce77 Pc Programming Software

    This field sets the Default Receive Frequency of the er. With the CE77 PC Programming Software, you VFO. can quickly and easily program the Vertex Standard To enter the Receive Frequency, double click the left VX-1700 operating channels and configuration from mouse button on this column, then enter the desired your personal computer.
  • Page 22 CE77 PC Programming Software MODE SHIFT This column selects the Operating Mode. This column may used to move a spurious response To select the Operating Mode, double click the left “Birdie” from the CPU clock away from the operat- mouse button on this column to invoke a pop-up ing frequency, should it cause interference.
  • Page 23 CE77 PC Programming Software Main Programming Screen (Memory Screen) This column is used for entry of the six character CHN (CHANNEL) Alpha/Numeric “Tag” used to identify the channel. This number is used to identify the memory chan- To enter the Alpha/Numeric “Tag,” double click the nel.
  • Page 24 CE77 PC Programming Software RECEIVE FREQUENCY set Frequency from the keyboard, then press the [EN- This column is used for entry of the Receive Frequen- TER] key to accept the new frequency. If an incorrect entry is made, the entry will be round- To enter the Receive Frequency, double click the left ed off to the nearest valid frequency automatically.

  • Page 25: File Menu

    CE77 PC Programming Software SAVE AS File Menu Save the programming session to the disk with the new name. Opens a new file. Click the left mouse button on the “Save As” param- Click the left mouse button on the “New” parame- eter in the File menu, a pop-up window appears ter in the File menu;...

  • Page 26: Edit Menu

    CE77 PC Programming Software Edit Menu View Menu COPY TOOL BAR Use this command to copy selected data onto the The toolbar is displayed across the top of the appli- clipboard. This command is unavailable if there is cation window, below the menu bar. The toolbar no data currently selected.
  • Page 27 CE77 PC Programming Software CW QSK Common Menu This parameter sets the delay time between the A1A (CW) FUNCTION PARAMETERS instant when the telegraph key is closed (key This parameter programs the various configuration down) and the moment the actual carrier enve- items of the A1A (CW) mode.
  • Page 28 CE77 PC Programming Software 4 - 30 MHz RF POWER HARDWARE PARAMETERS Put a check mark into the check box to enable ad- This parameter programs the TX output power justment of its parameter from the transceiver’s set on the 4 - 30 MHz band for each power setting (“menu”) mode.
  • Page 29 CE77 PC Programming Software PU/D SET KEY FUNCTION PARAMETERS This parameter sets the configurations for the key- This parameter programs the Programmable pad and button functions of the radio. Function Button feature which is located between Put a check mark into the check box to enable ad- the CH and VOL knobs.
  • Page 30 CE77 PC Programming Software MARKETING PARAMETERS MISCELLANEOUS PARAMETERS This parameter indicates the Market Application This parameter programs the miscellaneous config- Number and Serial Number of the radio. uration options of the radio. The available parameters are Market Applications Put a check mark into the check box to enable ad- and Serial Number.
  • Page 31 CE77 PC Programming Software BEEP TONE SCAN RESUME This parameter sets the Beep Tone (frequency). This parameter selects the Scan Resume Mode. The available selections are “LOW,” “NORMAL,” The available selections are “Carrier” and “Tim- and “HIGH.” er.” STANDBY BEEP BEEP AF SET This parameter defines whether the Beep volume This parameter toggles the Standby Beep feature...
  • Page 32 CE77 PC Programming Software CLARIFIER BACKUP TYPE SYSTEM PARAMETERS This parameter programs the various system con- This parameter determines the Clarifier offset fre- figurations of the radio. quency when the memory channel is recalled. Put a check mark into the check box to enable ad- The available selections are “PRESET,”...
  • Page 33 CE77 PC Programming Software MIC GAIN TUNING This parameter programs the Microphone Input This parameter programs the Automatic Anten- Sensitivity. na Tuner function. The available values for the Microphone Gain are The available selections are: OFF: Disables the automatic tuning “LOW,”...
  • Page 34 CE77 PC Programming Software DW CH SEL OPTION PARAMETERS This parameter defines whether the “DW CH This parameter programs the configurations of op- SEL” selection shall be “Enabled” or “Disabled” tional modules for the radio. from the transceiver’s set (“menu”) mode. These include the Encryption Unit and the Option Board.
  • Page 35 CE77 PC Programming Software STUN SYSTEM Selcall Menu This parameter determines whether the radio is SELCALL PARAMETERS able to receive a Stun System command or trans- This parameter programs the various Selcall config- mit a Stun System acknowledge command. urations of the radio. The available selections are “RX,”...
  • Page 36 CE77 PC Programming Software GPS POSITION REQUEST RADIO ID This parameter determines whether the radio is This parameter programs the transceiver’s Alpha/ able to receive or transmit a GPS position request. Numeric self-identification for the KILL and The available selections are “RX,” “TX,” “TX+RX,” STUN systems.
  • Page 37 CE77 PC Programming Software ALL CALL TEL CALL This parameter determines whether the “All Call” This parameter determines whether the radio is function of the Selcall feature shall be “Enabled” able to receive or transmit a Tel Call. or “Disabled”. The available selections are “RX,”...
  • Page 38 CE77 PC Programming Software TX ID PARAMETER This parameter programs the Selcall TX ID to be called. To program this parameter, enter the TX ID (4 dig- its) into the “TX ID” column, then set the desired effective channel range (i.e. 1-001, 1-050, 2-051, etc.) for the TX ID into the “FROM”...
  • Page 39 CE77 PC Programming Software LINK TOT ALE Menu This parameter define whether the Link TOT fea- ALE COMMON PARAMETERS ture shall be “Enabled (ON)” or “Disabled (OFF).” This parameter programs the various configurations When this parameter is set to “ON,” the link to for the ALE (Automatic Link Establishment) system the other radio will be automatically disconnect- of the radio.
  • Page 40 CE77 PC Programming Software NET NUMBER AMD MESSAGE PARAMETERS Put a check mark into the check box to enable ad- This parameter programs the Alpha/Numeric mes- justment of its parameter from the transceiver’s sages in accordance with the AMD definition. set (“menu”) mode.
  • Page 41 CE77 PC Programming Software ALL CALL SET ALE MISCELLANEOUS PARAMETERS This parameter programs the various configurations This parameter determines whether the ALE is for the ALE (Automatic Link Establishment) system able to receive or transmit an All Call feature. of the radio. The available selections are “RX,”...
  • Page 42 CE77 PC Programming Software SILENT MODE AUTO DIAL PARAMETER This parameter defines whether the Silent mode This parameter programs the address and message shall be “Enabled (SILENT)” or “Disabled (NOR- for the ALE Call. MAL).” To enter the address, double click the left mouse When this parameter is set to “Enabled (SI- button on the desired “Address”...
  • Page 43 CE77 PC Programming Software NET MEMBER ADDRESS PARAMETER This parameter defines the network member address to be called. To enter the network nember address, select the net- work from the pull-down list, then double click the left mouse button on the desired bank to invoke a pop-up window, select the desired address, then click the [OK] button to accept the address.
  • Page 44 CE77 PC Programming Software Channel Menu Radio Menu CHANNEL ALLOCATION PARAMETER UPLOAD PARAMETER The VX-1700 is capable of allocating up to 200 chan- Reads the configuration data from the radio to the nels into 5 banks. computer. Existing data on the screen will be over- By default, Bank-1 is filled with all memories (200 written with data from the radio, and will be lost channels);...
  • Page 45 CE77 PC Programming Software DOWNLOAD PARAMETER REVIVE PARAMETER Writes the configuration data from the computer to This parameter returns the radio to the normal mode the radio. Data will be verified for integrity by the from the STUN mode. program before downloading is initiated. Turn the stunned radio on and wait 2 seconds, then NOTE: Make sure to select the correct communica- click the [Revive] button to return the radio to the...
  • Page 46 CE77 PC Programming Software Programming Example 1 Selcall Feature Basic Setup 1. Assign the “SELCALL” function into the “Pro- grammable Function key 1 (P1 SET)” and the “CALL” function to the “Programmable Function key 2 (P2 SET)” from the “KEY FUNCTION” pa- rameter in the “Common”...
  • Page 47 CE77 PC Programming Software Programming Example 2 ALE Feature Basic Setup 1. Set the “Optional Board” parameter which is lo- cated in the “Option” folder in the “Common” menu to the “ALE Unit” to activate the optional ALE-1 Unit. 2. Set the “ALE” parameter in the “ALE Common” folder in the “ALE”...
  • Page 48 CE77 PC Programming Software Programming Example 3 Programming Example 5 Kill Command Setup Revive Command Setup Enter the Kill Command (CILLIK) and Radio ID Enter the Revive Command (SVIVER) and Radio (ex. TEST6111) into the “Message” parameter on ID (ex. TEST6111) into the “Message” parameter the “Selcall”...

  • Page 49: Main Unit

    MAIN Unit (Lot. 1~18) Circuit Diagram...
  • Page 50 MAIN Unit (Lot. 1~18) Note...
  • Page 51 MAIN Unit (Lot. 1~18) Parts Layout (Side A) AK4528VF HD64F2134 (Q1018) (Q1071) KIA7808API TDA2003H BA05FP TC7S04FU (E5) TC7ST08FU UPD77115GK (Q1007) (Q1055) (Q1012) (Q1059, 1062) (Q1080) (Q1035) 2SA1365 2SC2714 (QY) 2SC2954 (QK) (Q1048) (Q1016, 1021, 1023, (Q1001, 1029) 1026, 1027, 1063, 2SA1602A (MF) 2SC3357 (RK) 1064, 1070, 1074,...
  • Page 52 MAIN Unit (Lot. 1~18) Parts Layout (Side B)
  • Page 53 MAIN Unit (Lot. 19~) Circuit Diagram...
  • Page 54 MAIN Unit (Lot. 19~) Note...
  • Page 55 MAIN Unit (Lot. 19~) Parts Layout (Side A) HD64F2134 AK4528VF (Q1018) (Q1071) KIA7808API TDA2003H BA05FP TC7S04FU (E5) TC7ST08FU UPD77115GK (Q1007) (Q1055) (Q1012) (Q1059, 1062) (Q1080) (Q1035) (Q1031:Lot. 19-) L78M05T 2SC2714 (QY) 2SC2954(QK)(Lot.1-18) (Q1008) (Q1016, 1021, 1023, 2SC5415E (EA) (Lot. 1026, 1027, 1063, 19-) UPC2926T 1064, 1070, 1074,...
  • Page 56 MAIN Unit (Lot. 19~) Parts Layout (Side B)

  • Page 57: Parts List

    MAIN Unit Parts List REF. DESCRIPTION VALUE TOL. MFR’S DESIG VXSTD P/N VERS. LOT. SIDE LAY ADR PCB with Components CS1853002 Printed Circuit Board AC051H000 FR010270F 1-18 FR010270G C 1002 CHIP CAP. 0.01uF GRM39B103K25PT K22144803 C 1002 CHIP CAP. 0.01uF GRM188B11H103KA01D K22174823 C 1003 CHIP CAP.
  • Page 58 MAIN Unit Parts List REF. DESCRIPTION VALUE TOL. MFR’S DESIG VXSTD P/N VERS. LOT. SIDE LAY ADR C 1059 CHIP CAP. 0.047uF GRM39B473K16PT K22124804 C 1059 CHIP CAP. 0.047uF GRM188B11E473KA01D K22144811 C 1060 AL.ELECTRO.CAP. 470uF RE3-16V471MG3# K40129066 C 1061 CHIP TA.CAP. 4.7uF TEESVA1C475M8R K78120031...
  • Page 59 MAIN Unit Parts List REF. DESCRIPTION VALUE TOL. MFR’S DESIG VXSTD P/N VERS. LOT. SIDE LAY ADR C 1111 CHIP CAP. GRM1882C1H8R0DZ01D K22174209 C 1112 CHIP CAP. 10pF GRM1882C1H100JA01D K22174211 C 1112 CHIP CAP. GRM1882C1H8R0DZ01D K22174209 C 1114 CHIP CAP. 200pF GRM1882C1H201JA01D K22174242...
  • Page 60 MAIN Unit Parts List REF. DESCRIPTION VALUE TOL. MFR’S DESIG VXSTD P/N VERS. LOT. SIDE LAY ADR C 1163 CHIP TA.CAP. TEESVA1C105M8R K78120009 C 1164 CHIP CAP. 0.022uF GRM39B223K25PT K22144807 C 1164 CHIP CAP. 0.022uF GRM188B11H223KA01D K22174839 C 1165 CHIP CAP. 0.01uF GRM39B103K25PT K22144803...
  • Page 61 MAIN Unit Parts List REF. DESCRIPTION VALUE TOL. MFR’S DESIG VXSTD P/N VERS. LOT. SIDE LAY ADR C 1207 CHIP CAP. 0.022uF GRM188B11H223KA01D K22174839 C 1208 CHIP TA.CAP. 10uF TEESVA1A106M8R K78100028 C 1209 CHIP CAP. 0.022uF GRM39B223K25PT K22144807 C 1209 CHIP CAP. 0.022uF GRM188B11H223KA01D K22174839...
  • Page 62 MAIN Unit Parts List REF. DESCRIPTION VALUE TOL. MFR’S DESIG VXSTD P/N VERS. LOT. SIDE LAY ADR C 1255 CHIP CAP. 0.022uF GRM39B223K25PT K22144807 C 1255 CHIP CAP. 0.022uF GRM188B11H223KA01D K22174839 C 1256 CHIP CAP. 0.1uF GRM188B11C104KA01D K22124805 C 1257 AL.ELECTRO.CAP. 47uF EEE1CA470SP K48120005...
  • Page 63 MAIN Unit Parts List REF. DESCRIPTION VALUE TOL. MFR’S DESIG VXSTD P/N VERS. LOT. SIDE LAY ADR C 1311 CHIP CAP. 0.1uF GRM188B11C104KA01D K22124805 C 1312 CHIP CAP. 0.1uF GRM188B11C104KA01D K22124805 C 1313 CHIP CAP. 0.01uF GRM39B103K25PT K22144803 C 1313 CHIP CAP. 0.01uF GRM188B11H103KA01D K22174823...
  • Page 64 MAIN Unit Parts List REF. DESCRIPTION VALUE TOL. MFR’S DESIG VERS. LOT. SIDE LAY ADR C 1372 CHIP CAP. 0.022uF GRM188B11H223KA01D K22174839 C 1373 CHIP CAP. 0.022uF GRM39B223K25PT K22144807 C 1373 CHIP CAP. 0.022uF GRM188B11H223KA01D K22174839 C 1374 CHIP CAP. 15pF GRM1883U1H150JZ01D K22174312...
  • Page 65 MAIN Unit Parts List REF. DESCRIPTION VALUE TOL. MFR’S DESIG VXSTD P/N VERS. LOT. SIDE LAY ADR C 1421 CHIP CAP. 33pF GRM1882C1H330JA01D K22174223 C 1422 CHIP CAP. 0.01uF GRM39B103K25PT K22144803 C 1422 CHIP CAP. 0.01uF GRM188B11H103KA01D K22174823 C 1423 CHIP CAP. 0.01uF GRM39B103K25PT K22144803...
  • Page 66 MAIN Unit Parts List REF. DESCRIPTION VALUE TOL. MFR’S DESIG VXSTD P/N VERS. LOT. SIDE LAY ADR D 1012 DIODE 1SV271(TPH3.F) G2070476 D 1013 DIODE 1SV271(TPH3.F) G2070476 D 1014 DIODE 1SV271(TPH3.F) G2070476 D 1015 DIODE 1SV271(TPH3.F) G2070476 D 1016 DIODE 1SV271(TPH3.F) G2070476 D 1017 DIODE...
  • Page 67 MAIN Unit Parts List REF. DESCRIPTION VALUE TOL. MFR’S DESIG VXSTD P/N VERS. LOT. SIDE LAY ADR J 1016 CONNECTOR TCS7705-012010 P1091203 J 1016 CONNECTOR TCS7705-5120177 P1091244 J 1017 CONNECTOR M50006020-IIBA R41-9553D P1090925 J 1018 CONNECTOR M50-008-020 R41-9553F P1091132 J 1019 CONNECTOR 09FMN-BMTTN-TFT(LF)(SN) P1091089 JP1003 CHIP RES.
  • Page 68 MAIN Unit Parts List REF. DESCRIPTION VALUE TOL. MFR’S DESIG VXSTD P/N VERS. LOT. SIDE LAY ADR L 1059 M.RFC 100uH FLC32T-101J L1690227 L 1060 M.RFC 100uH FLC32T-101J L1690227 L 1061 CHIP COIL 0.33uH C2520C-R33G-RA L1691300 L 1063 M.RFC 3.3uH FLC32T-3R3K L1690209 L 1064 M.RFC...
  • Page 69 MAIN Unit Parts List REF. DESCRIPTION VALUE TOL. MFR’S DESIG VXSTD P/N VERS. LOT. SIDE LAY ADR Q 1043 FET 3SK151GR(TE85R.F) G4801517G Q 1044 TRANSISTOR 2SC2812N6-CPA-TB-E G3328128F Q 1045 TRANSISTOR PDTC144EE G3070244 Q 1046 TRANSISTOR 2SA1602A-T111-1F G3116028F Q 1046 TRANSISTOR ISA1602AM1-T111-1F G3070380 Q 1046 TRANSISTOR...
  • Page 70 MAIN Unit Parts List REF. DESCRIPTION VALUE TOL. MFR’S DESIG VXSTD P/N VERS. LOT. SIDE LAY ADR R 1023 CHIP RES. 1/16W 5% RMC1/16 103JATP J24185103 R 1024 CHIP RES. 100k 1/16W 5% RMC1/16 104JATP J24185104 R 1025 CHIP RES. 6.8k 1/16W 5% RMC1/16 682JATP...
  • Page 71 MAIN Unit Parts List REF. DESCRIPTION VALUE TOL. MFR’S DESIG VXSTD P/N VERS. LOT. SIDE LAY ADR R 1095 CHIP RES. 4.7k 1/16W 5% RMC1/16 472JATP J24185472 R 1096 CHIP RES. 1/16W 5% RMC1/16 560JATP J24185560 R 1097 CHIP RES. 1/16W 5% RMC1/16 391JATP J24185391...
  • Page 72 MAIN Unit Parts List REF. DESCRIPTION VALUE TOL. MFR’S DESIG VXSTD P/N VERS. LOT. SIDE LAY ADR R 1166 CHIP RES. 1/16W 5% RMC1/16 331JATP J24185331 R 1167 CHIP RES. 4.7k 1/16W 5% RMC1/16 472JATP J24185472 R 1168 CHIP RES. 1/16W 5% RMC1/16 000JATP J24185000...
  • Page 73 MAIN Unit Parts List REF. DESCRIPTION VALUE TOL. MFR’S DESIG VXSTD P/N VERS. LOT. SIDE LAY ADR R 1245 CHIP RES. 1/16W 5% RMC1/16 471JATP J24185471 R 1246 CHIP RES. 100k 1/16W 5% RMC1/16 104JATP J24185104 R 1247 CHIP RES. 1/16W 5% RMC1/16 102JATP J24185102...
  • Page 74 MAIN Unit Parts List REF. DESCRIPTION VALUE TOL. MFR’S DESIG VXSTD P/N VERS. LOT. SIDE LAY ADR R 1323 CHIP RES. 1/16W 5% RMC1/16 221JATP J24185221 R 1324 CHIP RES. 1/16W 5% RMC1/16 221JATP J24185221 R 1325 CHIP RES. 1/16W 5% RMC1/16 102JATP J24185102 R 1326 CHIP RES.
  • Page 75 MAIN Unit Parts List REF. DESCRIPTION VALUE TOL. MFR’S DESIG VXSTD P/N VERS. LOT. SIDE LAY ADR R 1397 CARBON FILM RES. 1/6W RD16PJ102 1K J01225102 R 1399 CHIP RES. 1/8W RMC1/8T 000J J24215000 R 1998 CHIP RES. 1/16W 5% RMC1/16 000JATP J24185000 R 1999 CHIP RES.
  • Page 76 MAIN Unit Note...

  • Page 77: Unit

    PA-2 Unit (Lot. 1~18) Circuit Diagram...
  • Page 78 PA-2 Unit (Lot. 1~18) Note...
  • Page 79 PA-2 Unit (Lot. 1~18) Parts Layout (Side A) SD1405 2SB1143S (Q2012, 2013) (Q2002) KIA7808API LM2904PWR (Q2003) (Q2015) 2SC3420GR RD06HHF1 (Q2007) (Q2001) RD16HHF1 (Q2008, 2009) DTC114TK (04) DTC124GUA (K25) (Q2006) (Q2004, 2010) DTC323TK (H02) TA75S01F (SA) (Q2011) (Q2005, 2014) DAN202K (N) (D2004)
  • Page 80 PA-2 Unit (Lot. 1~18) Parts Layout (Side B)
  • Page 81 PA-2 Unit (Lot. 19~) Circuit Diagram...
  • Page 82 PA-2 Unit (Lot. 19~) Note...
  • Page 83 PA-2 Unit (Lot. 19~) Parts Layout (Side A) 2SC2879A 2SB1143S (Q7012, 7013) (Q7002) KIA7808API LM2904PWR (Q7003) (Q7015) 2SC3420GR RD06HHF1 (Q7007) (Q7001) RD16HHF1 (Q7008, 7009) DTC114TK (04) DTC124GUA (K25) (Q7006) (Q7004, 7010) DTC323TK (H02) TA75S01F (SA) (Q7011) (Q7005) DAN202K (N) (D7004)
  • Page 84 PA-2 Unit (Lot. 19~) Parts Layout (Side B)
  • Page 85 PA-2 Unit Parts List REF. DESCRIPTION VALUE TOL. MFR’S DESIG VXSTD P/N VERS. LOT. SIDE LAY ADR PCB with Components CS1854001 Printed Circuit Board AC051H000 FR011850E FR014750A C 7001 CHIP CAP. 0.047uF GRM39B473K16PT K22124804 C 7001 CHIP CAP. 0.047uF GRM188B11E473KA01D K22144811 C 7002 CHIP CAP.
  • Page 86 PA-2 Unit Parts List REF. DESCRIPTION VALUE TOL. MFR’S DESIG VXSTD P/N VERS. LOT. SIDE LAY ADR C 7079 CHIP CAP. 0.047uF GRM188B11E473KA01D K22144811 C 7080 CHIP CAP. 0.047uF GRM39B473K16PT K22124804 C 7080 CHIP CAP. 0.047uF GRM188B11E473KA01D K22144811 C 7081 CHIP CAP. 0.047uF GRM39B473K16PT K22124804...
  • Page 87 PA-2 Unit Parts List REF. DESCRIPTION VALUE TOL. MFR’S DESIG VXSTD P/N VERS. LOT. SIDE LAY ADR C 7142 CHIP CAP. 220pF GRM1882C1H221JA01D K22174243 C 7143 CHIP CAP. 180pF 200V GRM21B2C2D181JY21L K22230231 C 7144 CHIP CAP. 0.001uF 500V CF43CH102J500AT K22277222 C 7145 CHIP CAP.
  • Page 88 PA-2 Unit Parts List REF. DESCRIPTION VALUE TOL. MFR’S DESIG VXSTD P/N VERS. LOT. SIDE LAY ADR C 7203 CHIP CAP. 0.1uF GRM21BB11E104KA01L K22140811 C 7204 CHIP CAP. 330pF 500V CF43CH331J500AT K22277210 C 7204 CHIP CAP. 0.001uF GRM188B11H102KA01D K22174821 C 7205 FILM CAP. 100pF 500V UC342H1000J-T...
  • Page 89 PA-2 Unit Parts List REF. DESCRIPTION VALUE MFR’S DESIG VXSTD P/N VERS. SIDE LAY ADR P 7001 CONNECTOR IMSA-9206H-T P1090988 FCC ON 1-21 P 7001 CONNECTOR IMSA-9206H-T P1090988 UNIT B P 7002 WIRE ASSY AC051H T9207202A FCC ON 1-21 P 7002 WIRE ASSY AC051H T9207202A UNIT B P 7003 CONNECTOR...
  • Page 90 PA-2 Unit Parts List REF. DESCRIPTION VALUE TOL. MFR’S DESIG VXSTD P/N VERS. LOT. SIDE LAY ADR R 7043 METAL FILM RES. ERG-2SJ150P 15 J22339023 R 7044 CHIP RES. RMC1 560JTE J24305560 R 7045 CHIP RES. 1/16W 5% RMC1/16 473JATP J24185473 R 7046 CHIP RES.

  • Page 91: Panel Unit

    PANEL Unit Circuit Diagram...
  • Page 92 PANEL Unit Note...
  • Page 93 PANEL Unit Parts Layout (Side A)
  • Page 94 PANEL Unit Parts Layout (Side B) 2SC4154 (E) CPH6102 (AB) DTC143ZE (E23) LC75884W (Q3005) (Q3005) (Q3006) (Q3001)
  • Page 95 PANEL Unit Parts List REF. DESCRIPTION VALUE TOL. MFR’S DESIG VXSTD P/N VERS. LOT. SIDE LAY ADR PCB with Components CB2833001 Printed Circuit Board AC051H000 FR0118600 C 3001 CHIP CAP. 0.047uF GRM39B473K16PT K22124804 C 3001 CHIP CAP. 0.047uF GRM188B11E473KA01D K22144811 C 3002 CHIP CAP.
  • Page 96 PANEL Unit Parts List REF. DESCRIPTION VALUE TOL. MFR’S DESIG VXSTD P/N VERS. LOT. SIDE LAY ADR S 3009 TACT SWITCH SKRPABE010 N5090133 S 3010 TACT SWITCH SKHHDU N5090080 S 3011 TACT SWITCH SKRPABE010 N5090133 S 3012 TACT SWITCH SKRPABE010 N5090133 S 3013 TACT SWITCH SKRPABE010...

  • Page 97: Gps-Interface Unit

    GPS-INTERFACE Unit (Lot. 1~6) Circuit Diagram...
  • Page 98 GPS-INTERFACE Unit (Lot. 1~6) Parts Layout (Side A) TC7W04FU 2SC4154 (E) (Q4019) (Q4010, 4012)
  • Page 99 GPS-INTERFACE Unit (Lot. 1~6) Parts Layout (Side B)
  • Page 100 GPS-INTERFACE Unit (Lot. 7~25) Circuit Diagram...
  • Page 101 GPS-INTERFACE Unit (Lot. 7~25) Parts Layout (Side A) TC7W04FU 2SC4154 (E) (Q4019) (Q4010, 4012)
  • Page 102 GPS-INTERFACE Unit (Lot. 7~25) Parts Layout (Side B)
  • Page 103 GPS-INTERFACE Unit (Lot. 26~) Circuit Diagram...
  • Page 104 GPS-INTERFACE Unit (Lot. 26~) Parts Layout (Side A) TC7W04FU 2SC4154 (E) (Q4019) (Q4010, 4012)
  • Page 105 GPS-INTERFACE Unit (Lot. 26~) Parts Layout (Side B)
  • Page 106 GPS-INTERFACE Unit Parts List REF. DESCRIPTION VALUE TOL. MFR’S DESIG VXSTD P/N VERS. LOT. SIDE LAY ADR PCB with Components CB3183001 Printed Circuit Board AC051H000 FR011870B FR011870C 7-25 FR011870D C 4014 CHIP CAP. 0.01uF GRM39B103K25PT K22144803 C 4014 CHIP CAP. 0.01uF GRM188B11H103KA01D K22174823...

  • Page 107: Mic Unit

    MIC Unit Circuit Diagram Parts Layout Side A Side B Parts List REF. DESCRIPTION VALUE TOL. MFR’S DESIG VXSTD P/N VERS. LOT. SIDE LAY ADR PCB with Components CB3199001 Printed Circuit Board AC051H000 FR0136100 J 6001 CONNECTOR R41-2509R P1091243 J 6002 CONNECTOR B8B-ZR-SM3-TFT P0091414...

  • Page 108: Enc Unit

    ENC Unit Circuit Diagram Parts Layout Side A Side B Parts List REF. DESCRIPTION VALUE TOL. MFR’S DESIG VXSTD P/N VERS. LOT. SIDE LAY ADR PCB with Components CB3200001 Printed Circuit Board AC051H000 FR0136200 C 6101 CHIP CAP. 0.1uF GRM188B11C104KA01D K22124805 J 6101 CONNECTOR...

  • Page 109: Ale Unit (Option)

    ALE Unit (Option) Circuit Diagram...
  • Page 110 ALE Unit (Option) Parts Layout Parts Layout (Side B) Side A Side B HD64F2134 ADM202EARU NJM2902V BR24L64F TC7W14FU BA05FP (Q4009) (Q4009) (Q4007) (Q4008) (Q4019) (Q4005) M51945BFP (Q4002) LH52256CT 2SC4047 (ZY) 2SC4154 (E) 2SD2211 (DQR) TC7S04FU (E5) MC2850 (A7) (Q4001) (Q4006) (Q4003, 4010, 4012, (Q4004) (Q4023)
  • Page 111 L1690335 Q 4001 IC HD64F2134ATF20V Q 4002 IC LH52256CT-70LL G1093162 Q 4003 IC BR24L64F-WE2 G1093876 Q 4004 IC M51945BFP-CF0R G1091990 Q 4005 IC BA05FP-E2 G1093209 Q 4006 TRANSISTOR 2SC4047-TA G3340477 Q 4007 IC NJM2902V-TE1 G1091679 : Please contact VERTEX STANDARD...
  • Page 112 ALE Unit (Option) Parts List REF. DESCRIPTION VALUE TOL. MFR’S DESIG VXSTD P/N VERS. LOT. SIDE LAY ADR Q 4009 IC ADM202EARU-REEL G1092958 Q 4010 TRANSISTOR 2SC4154-T111-1E G3341548E Q 4011 PHOTO COUPLER TLP281(GB-TP) G0090037 Q 4012 TRANSISTOR 2SC4154-T111-1E G3341548E Q 4013 IC TC7W14FU(TE12L.F) G1093321 Q 4014 TRANSISTOR...
  • Page 113 ALE Unit (Option) Parts List REF. DESCRIPTION VALUE TOL. MFR’S DESIG VXSTD P/N VERS. LOT. SIDE LAY ADR R 4075 CHIP RES. 1/16W 5% RMC1/16 000JATP J24185000 R 4076 CHIP RES. 1/16W 5% RMC1/16 000JATP J24185000 R 4077 CHIP RES. 1/16W 5% RMC1/16 000JATP J24185000...
  • Page 114 ALE Unit (Option) Note...
  • Page 116 Copyright 2011 VERTEX STANDARD CO., LTD. All rights reserved No portion of this manual may be reproduced without the permission of VERTEX STANDARD CO., LTD.

Table of Contents