Download
Share
Print this page
  1. Manuals
  2. Brands
  3. TP-Link Manuals
  4. Wireless Access Point
  5. TL-WA5110G
  6. Quick installation manual

TP-Link TL-WA5110G Quick Installation Manual

Hide thumbs Also See for TL-WA5110G:

Advertisement

Quick Links

See also: User Manual
Note
Please use only wired network connections to configure the AP.
Turn off all your network devices,
including your computer(s), power
injector and the AP.
Connect your computer to the
LAN port on the power injector
with an Ethernet cable.
Plug the provided power adapter
into the DC jack on the power
injector, and the other end to a
standard electrical wall socket.
Connect your AP to the PoE port
on the power injector with an
Ethernet cable.
The power adapter can be directly connected to the AP too. In this way
Note
you can connect your computer directly to the AP with an Ethernet cable.
1

Advertisement

loading

Related Manuals for TP-Link TL-WA5110G

Summary of Contents for TP-Link TL-WA5110G

  • Page 1 Note Please use only wired network connections to configure the AP. Turn off all your network devices, including your computer(s), power injector and the AP. Connect your computer to the LAN port on the power injector with an Ethernet cable. Plug the provided power adapter into the DC jack on the power injector, and the other end to a...
  • Page 2 Turn on all your network devices and then check to see if the LEDs on the AP display normally as the diagram below describes. Solid light Flashing Solid light or flashing Flashing if the Wireless Radio function is enabled If the LEDs display abnormally, please check to see if all the cable connectors Note (power adapter and Ethernet cable) are well connected to your device.

  • Page 3: Operation Mode Setting

    A dialog box will prompt you for the User name and Password. Enter the default values and click OK. User name: admin Password: admin Click OK If the dialog box does not pop up, please refer to T3 in the Troubleshooting Note guide.
  • Page 4 The AP supports three operation mode types: AP Client Router, AP Router Note and AP. If you want to connect to your WISP, please choose AP Client Router mode and proceed to A If you want to configure a point to point connection, please skip to B; If you want to configure a repeater, please skip to C.

  • Page 5: Configuration For Point-To-Point Connection

    The changes will take effect after rebooting. Click Finish After successfully logging in, configure the other TL-WA5110G by following the steps below. 2) The Client Setting You should change the default LAN IP address of the Client from Note 192.168.1.254 to 192.168.1.X (X can be any number from 1 to 253) to avoid...
  • Page 6 Click Network Enter 192.168.1.2 in the IP Address field Click Save Note The AP will begin rebooting automatically after clicking Save. Click Wireless > Wireless Mode Select Client Enter TP-LINK_88346E, the SSID of the first AP you configured Click Save at the bottom of this page. Configuration for Repeater Click Wireless >...
  • Page 7 Find the BSSID of the remote AP that you want to repeat, and then write it down or copy it. Here we copy the BSSID of ‘TP-LINK’ that is 00-19-E0-94-51-F4 Enter or paste the BSSID of the remote AP into the box under Repeater The BSSID is the same as the MAC address.
  • Page 8 How do I restore my Router’s configuration to its factory default settings? With the AP powered on, press and hold the RESET button on the rear panel for 8 to 10 seconds before releasing it. Hold it in for 8 to 10 seconds Once the AP is reset, the current configuration settings will be lost and you Note...
  • Page 9 For Windows XP OS Go to Start > Control Panel, will then following page. Click Network and Internet Connections Click Network Connections Right-click Local Area Connection Click Properties...
  • Page 10 Double-click Internet Protocol (TCP/IP) Select Use the following IP address Enter the 192.168.1.100 into the IP address field, 255.255.255.0 into the Subnet mask field Select Use the following DNS server addresses Enter the DNS server address provided by your ISP or network administrator Click OK...
  • Page 11 For Windows Vista / Windows 7 OS Go to Start > Settings > Control Panel, and then you will see the following page. Click View network status and tasks Click View status Click Properties...
  • Page 12 Double-click Internet Protocol Version 4 (TCP/IPv4) Select Use the following IP address Enter the 192.168.1.100 into the IP address field, 255.255.255.0 into the Subnet mask field Select Use the following DNS server addresses Enter the DNS server address provided by your ISP or network administrator Click OK...
  • Page 13 AP’s factory default settings and reconfigure your AP following the instructions of this QIG. Please feel free to contact our Technical Support if the problem persists. For more details about Troubleshooting and Technical Support contact Note information, please logon to our Technical Support Website: http://www.tp-link.com/support/Support.asp...

  • Page 14: Technical Support

    Global Australia & New Zealand Tel: +86 755 26504400 Tel: AU 1300 87 5465 E-mail : support@tp-link.com NZ 0800 87 5465 Service time:24hrs, 7days a week E-mail: support@tp-link.com.au Service time: Monday to Friday 9:00 AM to 9:00 PM AEST...