Table of Contents
Advertisement
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."
These words mean:
DANGER
WARNING
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
Tools and Parts
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
Tools needed
Phillips screwdriver
Measuring tape
Hand or electric drill (for wall cabinet installations)
1" (2.5 cm) drill bit (for wall cabinet installations)
Level
Flat-blade screwdriver
Parts needed
UL listed or CSA approved conduit connector
UL listed wire connectors
Warming Drawer Deflector Kit (for ovens installed above a
warming drawer)
Order Part Number W10489566 for white 27" (68.6 cm) kit
Order Part Number W10489564 for black 27" (68.6 cm) kit
Order Part Number W10489568 for stainless steel 27"
(68.6 cm) kit
Order Part Number W10489567 for white 30" (76.2 cm) kit
Order Part Number W10489565 for black 30" (76.2 cm) kit
Order Part Number W10489569 for stainless steel 30"
(76.2 cm) kit
To order, see the "Assistance or Service" section of the Use
and Care Guide.
Parts supplied
#8-14 x 1" screws - single ovens (2), double ovens (4)
Two #8-18 x ³⁄₈" screws - bottom vent
Four #8-18 x ¹⁄₄" screws - bottom vent trim
Four #8-18 x ³⁄₈" screws - double oven feet
2
BUILT-IN OVEN SAFETY
Your safety and the safety of others are very important.
INSTALLATION REQUIREMENTS
You can be killed or seriously injured if you don't immediately
follow instructions.
You can be killed or seriously injured if you don't follow
instructions.
Bottom vent
Bottom vent trim
Two feet - double oven
Two front feet - double oven
Four grommets - single ovens (2), double ovens (4)*
Foam strip - single oven**
Check local codes. Check existing electrical supply. See
"Electrical Requirements."
It is recommended that all electrical connections be made by a
licensed, qualified electrical installer.
*Grommets not required or included with models KEBK171B,
KEBK101B, KEBK276B, KEBK206B, KEBS179B, KEBS109B,
KEBS277B, KEBS279B, KEBS207B, KEBS209B, KEBU109B
and KEBU209B.
**Foam strip not included with double oven.
Location Requirements
IMPORTANT: Observe all governing codes and ordinances.
Cabinet opening dimensions that are shown must be used.
Given dimensions provide minimum clearance with oven.
Recessed installation area must provide complete enclosure
around the recessed portion of the oven.
Grounded electrical supply is required. See "Electrical
Requirements" section.
Electrical supply junction box should be located 3" (7.6 cm)
maximum below the support surface when the oven is
installed in a wall cabinet. A 1" (2.5 cm) minimum diameter
hole should have been drilled in the right rear or left rear
corner of the support surface to pass the appliance cable
through to the junction box.
NOTE: For undercounter installation, it is recommended that
the junction box be located in the adjacent right or left
cabinet. If you are installing the junction box on rear wall
behind oven, it is recommended that the junction box be
recessed and located in the upper center of the cabinet.
Advertisement
Table of Contents
Related Manuals for KitchenAid KEBS209-BSS
Summary of Contents for KitchenAid KEBS209-BSS
-
Page 1: Installation Requirements
BUILT-IN OVEN SAFETY Your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. -
Page 2: Product Dimensions - Single Ovens
Oven support surface must be solid, level and flush with Cabinet Dimensions - Single Ovens bottom of cabinet cutout. Floor must be able to support a single oven weight of 129 lbs Single Oven Undercounter (without cooktop installed above) (59 kg) for 27" (68.6 cm) models or 154 lbs (70 kg) for 30"... -
Page 3: Product Dimensions - Double Ovens
Product Dimensions - Double Ovens Cabinet Dimensions - Double Ovens Double Ovens Installed in Cabinet 27" (68.6 cm) models 30" (76.2 cm) models ³⁄₁₆ ³⁄₁₆ A. 51 " (130.0 cm) max. overall A. 51 " (130.0 cm) max. overall 27" (68.6 cm) models 30"... -
Page 4: Electrical Requirements
Electrical Requirements If codes permit and a separate ground wire is used, it is Flexible conduit from the oven should be connected directly recommended that a qualified electrical installer determine that to the junction box. the ground path and the wire gauge are in accordance with local Fuse both sides of the line. -
Page 5: Installation Instructions
INSTALLATION INSTRUCTIONS 3. Grasp the edges of the oven door with both hands and close Prepare Built-In Oven the oven door until it will no longer close. Lift and pull oven door toward you and remove. Set the oven door(s) aside on a 1. - Page 6 Cutout Height is between 26¹⁵⁄₁₆" (68.4 cm) and Cutout Height is between 28¹¹⁄₁₆" (72.8 cm) and 27¹¹⁄₁₆" (70.3 cm) 29⁷⁄₁₆" (74.8 cm) 1. Using 2 or more people, place the oven on its back on a 1. Using 2 or more people, place the oven on its back on a covered surface.
- Page 7 6. Using 2 or more people, place the oven in its upright position. Double Ovens The positioning of the oven feet allow a double oven to be installed in a cutout height between 48⁷⁄₈" (124.1 cm) and 52³⁄₁₆" (132.6 cm). Refer to the following instructions to position the feet for the size of your cabinet cutout.
- Page 8 2. Install a foot on the left rear spacer using a #8-18 x ³⁄₈" screw. 6. Using 2 or more people, place the oven in its upright position. NOTE: Position the foot so the long side of the foot is facing toward the top of the oven.
-
Page 9: Make Electrical Connection
4. Install a front foot on the left front using a #8-18 x ³⁄₈" screw. 6. Using 2 or more people, place the oven in its upright position. NOTE: Position the foot so the long side of the foot is facing toward the inside of the oven.