Makita HM1202 Instruction Manual

Makita HM1202 Instruction Manual

Makita demolition hammer instruction manual hm1202, hm1202c
Hide thumbs Also See for HM1202:

Advertisement

Demolition Hammer
MODEL HM1202
MODEL HM1202C
I N S T R U C T I O N
WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
w w w . m a k i t a t o o l s . c o m
DOUBLE
INSULATION
M A N U A L
002877

Advertisement

Table of Contents
loading

Summary of Contents for Makita HM1202

  • Page 1 Demolition Hammer MODEL HM1202 MODEL HM1202C I N S T R U C T I O N WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. w w w . m a k i t a t o o l s . c o m...
  • Page 2: Specifications

    3. Keep bystanders, children, and visitors away while operating a power tool. Distrac- tions can cause you to lose control. Electrical Safety HM1202 1,900 578 mm (22-3/4”) 9.3 kg (20.5 lbs) 4. Double insulated tools are equipped with a polarized plug (one blade is wider than the other.) This plug will fit in a polarized...
  • Page 3: Personal Safety

    6. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. 7. Do not abuse the cord. Never use the cord to carry the tools or pull the plug from an outlet.
  • Page 4: Specific Safety Rules

    24. When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. USE PROPER EXTENSION CORD: Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw.
  • Page 5 tion. Without proper warm-up, hammering operation is difficult. 7. Always be sure you have a firm footing. Be sure no one is below when using the tool in high locations. 8. Hold the tool firmly with both hands. 9. Keep hands away from moving parts. 10.
  • Page 6: Functional Description

    FUNCTIONAL DESCRIPTION 002889 1. Switch lever 002897 1. Adjusting dial CAUTION: • Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. Switch action CAUTION: • Before plugging in the tool, always check to see that the tool is switched off.
  • Page 7: Indicator Lamp

    002899 1. Power-ON indicator lamp(green) 2. Service indicator lamp(red) ASSEMBLY 002903 1. Side handle 2. Clamp nut 002904 1. Side handle base 2. Clamp nut Indicator lamp For HM1202C only The green power-ON indicator lamp lights up when the tool is switched ON.
  • Page 8 002916 1. Bit grease 2. Bit shank 002922 1. Bit 2. Tool holder cover 002923 002939 1. Change ring Installing or removing the bit Clean the bit shank and apply bit grease before installing the bit. Insert the bit into the tool. Turn the bit and push it in until it engages.
  • Page 9: Operation

    OPERATION 002945 MAINTENANCE 001146 1. Commutator 2. Insulating tip 3. Carbon brush 002953 1. Screwdriver 2. Rear cover 3. Screws Chipping/Scaling/Demolition Hold the tool firmly with both hands. Turn the tool on and apply slight pressure on the tool so that the tool will not bounce around, uncontrolled.
  • Page 10 It should be relubri- cated after every 6 months of operation. Send the complete tool to Makita Authorized or Factory Service Center for this lubrication service. However, if circumstances require that you should lubricate it by yourself, proceed as follows.
  • Page 11 CAUTION: • These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose.
  • Page 12 Memo...
  • Page 13 First-Class Postage Required Post Office will not deliver without proper postage. Makita U.S.A., Inc. 14930 Northam Street La Mirada, CA 90638-5753 Fold...
  • Page 14 Paste 3. How did you learn about this product: Magazine From Dealer Newspaper Store Display Catalog 4. Most favored points are: Design Features Size Price Makita Brand MODEL NO. YEAR SERIAL NO. PHONE 20-29 30-39 40-49 Paste Paste Radio Exhibition...
  • Page 15: Factory Service Centers

    Date Purchased When you need service: Send complete tool (prepaid) to one Dealer’s Name & Address of the Makita Factory Service Centers listed, or to an Authorized Makita Service Center. Be sure to attach a letter to the outside of Model No.
  • Page 16 MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase.

This manual is also suitable for:

Hm1202c

Table of Contents