Advertisement
Quick Links
Cordless Drill
No
load speed
(RPMI
i
Capacities
Steel /Wood
Wood screw
Equipped with Keyless Chuck and Electric Brake
weight
Dimensions
IL x
W
x HI
10
mm
(318") MODEL 60761)
10
mm
(3/8") MODEL 6 0 7 6 D W
With Quick Charger
A.C.
only
50
Hz
-
6 0 Hz
INSTRUCTION
D.C. 7.2 V .
Approx.
3
Hr.
SPECIFICATIONS
Model
6 0 7 6 D
With Reversing Switch
81
Battery
10 mm
I
4 . 5 "
x 2 0 m m
1
6oo
1
2 1 0 m m
x
48
mm x
1 9 0 m m
0.94
kg
13/8"1
(311 6"
x
3/4"1
18-1/4"
x
1-7/8"
x
7-112")
1
12.1 Ibs)
I
I
I
I
Model
D C 7 0 2 0 B
Quick
Charger
Input
I
output
I
Charging time
Advertisement
Related Manuals for Makita 60761
Summary of Contents for Makita 60761
- Page 1 D C 7 0 2 0 B Charger Input only A.C. 6 0 Hz Cordless Drill Equipped with Keyless Chuck and Electric Brake (318”) MODEL 60761) (3/8”) MODEL 6 0 7 6 D W Battery load speed (RPMI 2 1 0 m m 18-1/4” output D.C.
-
Page 2: Important Safety Instructions
SAFETY INSTRUCTIONS WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. CONSIDER WORK AREA ENVIRONMENT. - Page 3 14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger on switch. sure switch OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords intended 17.
- Page 4 Before using battery charger, read all instructions and cautionary markings (11 battery charger, (2) battery, and (3) product using battery. CAUTION To reduce risk of injury, charge only MAKITA type recharge- able batteries. Other types of batteries may burst causing personal injury and damage.
- Page 5 ADDITIONAL SAFETY RULES FOR CHARGER AND TOOL 1. The Charger and the tool are specifically designed to attempt to charge any other cordless tool with this Charger. Do not attempt to charge the tool with any other charger. Do not charge the tool when temperature is BELOW 10°C (5OOF) or ABOVE 4 5 O C (113OFI.
- Page 6 Charging Connect the charging plug to then connector, plug power receptacle. Charging takes 3 hours. CAUTION: * T h e battery in your n e w charged. You will need to charge it before use. not operate the tool during charging. Overcharging more than ably s h o r t e n s t h e battery service life.
- Page 7 Holding tool tool as Hold shown When drilling a large diameter hole, hold the tool firmly with both hands. Switch action Move the reversing switch lever "FWD" position for clockwise rotation or the "REV" position for counterclockwise. To start the tool, simply pull the trigger. Release the trigger to stop.
- Page 8 Drilling ope rat ion Drilling wood When drilling in wood, best results are obtained with wood drills equipped with a guide screw. The guide screw makes drilling easier Drilling in metal To prevent the bit from slipping when starting a hole, make an indentation with a center- punch and hammer a t the point to be drilled.
-
Page 9: Maintenance
Always be sure that the maintenance. maintain product SAFETY and RELIABILITY, repairs, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. DISPOSING OF TOOL A nicad battery is built into the handle tool. - Page 10 Makita battery recycling location. Call your nearest Makita Service Center or Distributor to determine the location that provides Makita battery recycling. See your local yellow pages under “Tools - Electric. a Makita battery i s to recycle...
- Page 11 OPTIONAL ACCESSORIES in this The accessories listed Makita factory service center. Service centers are listed distributor your tool. card packed with CAUTION T h e s e accessories or a t t a c h m e n t s are recommended manual.
- Page 12 Jan -14-’93 10 mm (3/8”) CORDLESS DRILL Model 6 0 7 6 D Note: The switch and other part configurations may differ from country to country.
- Page 13 MODEL 6 0 7 6 D ,&, DESCRIPTION Tapping Screw M3x20 Name Plate Housing Set IWith Item 171 Cwunleraunh Her Soohel Scmw Keyless Drill C h u c k Gear Plane Bearing DC Motor 7 2 V Circuit Board Note The switch and other part specifications may differ from cnuntry to "...
- Page 14 MAKITA LIMITED O N E YEAR WARRANTY Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted be free of defects from workmanship and materials for original purchase. Should any trouble develop during this one-year period, return the COMPLETE...