Advertisement
Quick Links
Cordless Drill
Capacities
Steel /Wood
Wood screw
10 mm
(3/8")
MODEL 6041D
10 mm
(3/8")
MODEL 6041DW
Wlth Qulck Charger
No load speed
(RPM)
INSTRUCTION MANUAL
Input
A.C. only
50 Hz
-
60
Hz
SPECIFICATIONS
Model 6041D
output
Charging time
Approx.
3
Hr.
D.C.
6.4
V .
Dinensions
1
Net
(L
x W x
H)
weight
10 13/8,,,
mm
I
4.5 mm x
20
mm
I
201
mm
x
48 mm
x
180
mm
0.82
kg
(3/16"
x
3/4")
I
450
(7-7/8"
x
1-7/8"
x
7-1/8")
I
11.8
lbsl
Advertisement
Related Manuals for Makita 6041DW
Summary of Contents for Makita 6041DW
- Page 1 50 Hz A.C. only Cordless Drill 10 mm (3/8”) 10 mm (3/8”) No load speed (RPM) (7-7/8” output D.C. MODEL 6041D MODEL 6041DW Wlth Qulck Charger Dinensions x W x weight 48 mm 0.82 1-7/8“ 7-1/8”) 11.8 lbsl Charging time Approx.
- Page 2 SAFETY I NSTRU CTlO N S WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. CONSIDER WORK AREA ENVIRONMENT.
- Page 3 14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking t o see that keys and adjusting wrenches are removed from tool before turning 15. AVOID UNINTENTIONAL STARTING. Don’t carry plugged-in tool with finger switch. Be sure switch is 16. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords intended for use outdoors and so marked.
- Page 4 Before using battory charger, read all instructions and cautionary markings on (1) battery charger, CAUTION To reduce risk of injury, charge only MAKITA type recharge- able batteries. Other types of batteries may burst causing personal injury and damage. Do not expose charger to rain or snow.
- Page 5 ADDITIONAL SAFETY RULES FOR CHARGER AND TOOL The Charger and the attempt t o charge any other cordless tool with this Charger. t o charge the tool with any other charger. 2. Do not charge the tool when temperature is BELOW 45OC (113OF).
- Page 6 Charging Connect the charging plug to the charging connector, then plug in the charger to the power receptacle. Charging takes 3 hours. CAUTION: The battery in your new tool is not fully charged. You will need to charge it before use.
- Page 7 Holding tool When drilling large diameter hole, hold the tool firmly with both hands. Switch action start the tool, simply pull the trigger. Release the trigger to stop. Reversing switch action This tool has reversing switch to change the direction of rotation. Slide the revers- ing switch to the right for clockwise rota- tion or to the left for counterclockwise.
- Page 8 CAUTION : Pressing excessively on the tool will not speed up the drilling. In fact, this excessive pres- sure will only serve to damage the tip of your bit, decrease the tool performance and shorten the service life of the tool. -There is a tremendous force exerted on the tool/bit a t the time of hole breakthrough.
-
Page 9: Maintenance
Always be sure that the tool is switched off before attempting to perform inspection or maintenance. To maintain product SAFETY and RELlABl LITY, repairs, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. DISPOSING OF TOOL A nicad battery built into the handle of this tool. - Page 10 Remove the battery from the (a) Take the battery to your nearest Makita Factory Service Center. (b) Take the battery to your nearest Makita Authorized Service Center or Distributor that has been designated as a Makita battery recycling location. Call your nearest Makita Service Center or Distributor to determine the location that provides Makita battery recycling.
-
Page 11: Optional Accessories
OPTIONAL ACCESSORIES The accessories listed in distributor or Makita factory service center. Service centers are listed on the warranty card Dacked with vour tool. CAUTION: These accessories or attachments are recommended for manual. The use of any other accessories or attachments might present a risk of injury t o persons. - Page 12 Jan.-14-'93 10 mm (318") CORDLESS DRILL Model 60410 Note: The switch and other part configurations may differ from country to country.
- Page 13 MODEL 6041D ,& 'i\M DESCRIPTION Sum H 3 m Tappmg Name Plate Housing Set IWith Item cWmmuI* Hex -el Drill Chuck S 1 0 Gear Plane 8eCrl"g DCMolor4,L)v Switch Lever ComDre.lsm Swmg 1 other Note. The switch part ~ ~ e ~ i f i ~ a f m n s G&, 'i\M MSxZl...
- Page 14 MAKVA L I M l T E D ONE YEAR WARRAMY Every Makita tool is thorou ly inspected and tested before leaving the factory. It is warranted to be free of defects from w o r k a ~ & p and materials for the period of ONE YEAR from the date of original purchase.