Advertisement
Table of Contents
- 1 Table of Contents
- 2 Important Safety Instructions
- 3 Getting Started
- 4 Using the Vacuum
- 5 Cleaning with the Vacuum Accessories
- 6 Emptying the Dust Cup Assembly
- 7 Proper Care of Your Vacuum
- 8 Troubleshooting
- 9 Checking for Blockages
- 10 Resetting the Motor Thermostat
- 11 Maintenance
- Download this manual
Advertisement
Table of Contents
Related Manuals for Shark UV410
Summary of Contents for Shark UV410
- Page 1 UV410 Owner’s Guide www.sharkclean.com UV410_26_IB_ENG_120229_5.indd 1 12-02-29 1:30 PM...
- Page 2 This manual covers model numbers: UV410 26 TECHNICAL SPECIFICATIONS Voltage: 120V. Watts: 1200W Amps: 10A Hertz: 60Hz TOLL FREE: 1-800-798-7398 UV410_26_IB_ENG_120229_5.indd 2 12-02-29 1:30 PM...
-
Page 3: Table Of Contents
Contents Thank you for Important Safety Instructions purchasing Getting Started the Shark ® Using the Vacuum Navigator ™ Cleaning with the Vacuum Accessories Upright Vacuum. Emptying the Dust Cup Assembly Proper Care of Your Vacuum Troubleshooting Checking for Blockages Maintenance Warranty and Registration www.sharkclean.com... -
Page 4: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS For Household Use Only WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC WHEN USING YOUR SHARK NAVIGATOR ® ™ SHOCK OR INJURY: UPRIGHT VACUUM, BASIC SAFETY GENERAL ELECTRICAL SAFETY: PRECAUTIONS SHOULD ALWAYS BE 1. Unplug from electrical outlet when not in use FOLLOWED, INCLUDING THE FOLLOWING: and before servicing. - Page 5 GENERAL USE: GENERAL CLEANING: 25. DO NOT run the vacuum over large-sized 17. Use only as described in this manual. objects. 18. DO NOT put any objects into openings. 26. DO NOT pick up hard or sharp objects such as 19.
-
Page 6: Getting Started
Store the Crevice Tool, Dusting Cleaning Attachments Brush and Cleaning Wand on 24” Crevice Tool the unit. Extended Reach Kit Note: Optional tools are available for sale for any UV410 model: 1-800-798-7398. TOLL FREE: 1-800-798-7398 UV410_26_IB_ENG_120229_5.indd 4 12-02-29 1:30 PM... - Page 7 To store the vacuum: IMPORTANT: Attach the Super Stretch Hose: For suction to reach the Floor When storing your vacuum, Snap hose into swivel Power Nozzle, the Cleaning connector wind the cord around the two Wand and Super Stretch Hose cord holders and secure with Route under anti-tip hook must be attached securely on...
-
Page 8: Using The Vacuum
Bare Floors / Tools Release suction for easier push and pull on high pile carpets and area rugs. Carpets When cleaning carpets: Your Shark Navigator Upright ® ™ IMPORTANT: Vacuum can be used to clean bare Your Brushroll Indicator Light Ensure you have pulled the floors or carpets –... -
Page 9: Cleaning With The Vacuum Accessories
Cleaning with the Vacuum Accessories Extended Reach Cleaning Kit Using the Cleaning Wand: Stand the vacuum into upright position. Remove the Cleaning Wand (with hose attached) from the unit. Vacuum Accessories Push the selected tool into the Your vacuum comes with a Super Before cleaning with your end of the Cleaning Wand. -
Page 10: Emptying The Dust Cup Assembly
Option A: For Quick Empty: before continuing to vacuum; Locate the Dust Cup Door Insert Dust Cup deep inside Shark advanced cyclonic action ® release button within the trash trash receptacle to contain dust will sweep the metal screen bag and press to release as you and debris. -
Page 11: Proper Care Of Your Vacuum
Proper Care of Your Vacuum COMPONENT MAINTENANCE SCHEDULE Dust Cup Empty each time you vacuum. Pre-Motor Foam Filter Rinse and air dry every 3 months under normal use. Pre-Motor Felt Filter Rinse and air dry every 3 months under normal use. Post-Motor Filter Clean once every 12 months under normal use. NOTE: The material in the filters will discolor over time. This is NORMAL and will not affect the performance of the filters. -
Page 12: Troubleshooting
Troubleshooting WARNING: To reduce the risk of electric shock, the power cord must be disconnected before performing maintenance/troubleshooting checks. PROBLEM POSSIBLE REASONS & SOLUTIONS Check filters to see if they need cleaning. Follow instructions for rinsing and drying the filters before re-inserting back into the vacuum. (See “Maintenance” sections for instructions.) Vacuum is not Dust cup may be full;... -
Page 13: Checking For Blockages
Checking for Blockages Blockages may cause your vacuum to overheat and shut down. If so, clear the blockages, then follow the instructions for Resetting the Motor Thermostat on page 12. WARNING: Never insert sharp objects into any opening to clear an obstruction. -
Page 14: Maintenance
Maintenance Resetting the Motor Thermostat Your Shark Navigator Upright ® ™ Vacuum is equipped with a protective Motor Thermostat. If the motor should overheat, the thermostat shuts off the power. Cleaning the Pet Hair Power Brush - Slide locking latch (A) forward. Gently tilt brush housing upward to open. - Page 15 Product Registration Please visit www.sharkclean.com or call 1-800-798-7398 to register your new Shark product within ten (10) ® days of purchase. You will be asked to provide the store name, date of purchase and model number along with your name and address.
- Page 16 Euro-Pro Operating LLC USA: Newton, MA 02459 CAN: 4400 Bois Franc, St-Laurent, QC H4S 1A7 English: 1-800-798-7398 www.sharkclean.com Copyright © Euro-Pro Operating LLC 2012 Printed in China Illustrations may differ from actual product. UV410.E.120229.5 UV410_26_IB_ENG_120229_5.indd 14 12-02-29 1:30 PM...