Lowrance GlobalMap 540c BAJA Operation Instructions Manual

Lowrance GlobalMap 540c BAJA Operation Instructions Manual

Mapping gps receiver
Hide thumbs Also See for GlobalMap 540c BAJA:
Table of Contents

Advertisement

Pub. 988-0151-481
www.lowrance.com
®
GlobalMap
540c BAJA
Mapping GPS Receiver

Operation Instructions

Advertisement

Table of Contents
loading

Summary of Contents for Lowrance GlobalMap 540c BAJA

  • Page 1: Operation Instructions

    Pub. 988-0151-481 www.lowrance.com ® GlobalMap 540c BAJA Mapping GPS Receiver Operation Instructions...
  • Page 2 We reserve the right to do so without notice. All features and specifications subject to change without notice. On the cover: GlobalMap 540c BAJA. All screens in this manual are simulated. For free owner's manuals and the most current information on this product, its operation and accessories, All rights reserved.
  • Page 3: Table Of Contents

    To create and save a Waypoint:... 47 Create Waypoint at Current Position ... 47 Create Waypoint on Map ... 48 Navigate To a Waypoint ... 48 Set Man Overboard (MOB) Waypoint... 49 Navigate Back to MOB Waypoint ... 49 Table of Contents ® 540c BAJA... 2...
  • Page 4 Navigate to Cursor Position on Map... 50 Navigate to a Point of Interest ... 51 Creating and Saving a Trail ... 52 Displaying a Saved Trail ... 54 Navigating Trails ... 54 Visual Trailing... 55 Navigate a Trail ... 55 Navigate a Back Trail (backtrack, or reverse) ...
  • Page 5 Set a Waypoint by Average Position ... 74 Set a Waypoint by Projecting a Position... 74 Section 5: System & GPS Setup... 75 Alarms... 75 Auto Satellite Search ... 76 Check MMC Files and Storage Space... 77 Communications Port Configuration ... 77 Configure NMEA...
  • Page 6 Find Waypoints ... 123 Section 7: NMEA 2000 ... 127 NMEA 2000 Menu... 127 Bus Setup... 127 Engine & Tank Configuration... 128 Tank Select ... 129 Tank Size ... 129 Set Configuration button ... 129 Device Configuration Menu... 130 Device Information and Device Data ... 130 Fuel Management Menu...
  • Page 7 3-Point Calibration... 145 5-Point Calibration... 146 Fuel Flow Calibration in a Suzuki Engine Interface... 147 Engine Trim Calibration... 148 Reset Trim Calibration ... 149 Bennett Trim Tabs Calibration ... 149 Sec. 8: Supplemental Material ... 151...
  • Page 8 NOTICE! The storage and operation temperature range for your unit is from -20 degrees to +167 degrees Fahrenheit (-28 degrees to +75 degrees Cel- sius). Extended storage or operation in temperatures higher or lower than specified will damage the liquid crystal display in your unit. This type of damage is not covered by the warranty.
  • Page 9: Section 1: Read Me First

    First, we want to thank you for buying a Lowrance GPS unit. Whether you're a first time user or a professional fisherman, you'll discover that your GlobalMap 540c BAJA is easy to use, yet capable of handling de- manding navigation tasks. When you team your unit with our custom mapping software MapCreate™...
  • Page 10: Specifications: Globalmap ® 540C Baja

    Now, if you're into the fine details, glance over the next segment on speci- fications to see just how much GPS power your GlobalMap 540c BAJA contains. It's important to us (and our power users), but, if you don't care...
  • Page 11 Case size: ...5.4" H x 6.9" W x 3.4" D (13.8 x 17.6 x 8.6 MMC slots: ...One waterproof door (SD card compatible). Recording: ... MMC & SD memory cards for recording GPS Back-up memory:...Built-in memory stores GPS data for dec- Languages: ...10;...
  • Page 12: How Lowrance Gps Works

    How Lowrance GPS Works You'll navigate faster and easier if you understand how the GlobalMap 540c BAJA scans the sky to tell you where you are and where you're going. (But if you already have a working understanding of GPS receiv- ers and the GPS navigation system, skip to Section 2, Installation &...
  • Page 13: Introduction To Gps And Waas

    Well, now you know the basics of how the unit does its work. You might be ready to jump ahead to Section 2, Installation & Accessories, on page 11, so you can mount your GlobalMap 540c BAJA and plug in the power. Or you might want to see how our text formatting makes the manual tutorials easy to skim.
  • Page 14 But, if you want to understand the current state of satellite navigation, look over this segment describing how GPS and its new companion WAAS work together to get you where you're going. The Global Positioning System (GPS) was launched July 17, 1995 by the United States Department of Defense.
  • Page 15 WAAS signal from ground receivers. You'll find that using your GPS receiver is both easy and amazingly accurate. It’s easily the most accurate method of electronic navigation available to the general public today. Remember that this receiver is only a tool.
  • Page 16: How To Use This Manual: Typographical Conventions

    Free Training Aids Available Now that you know something about the technology that makes this unit possible, you are ready to start learning how to use that technol- ogy. This manual will guide you through the process of setting up and running your unit, but that is only one of many resources available.
  • Page 17: Menu Commands

    Menu Commands A menu command or a menu option will appear in small capital letters, in a bold sans serif type like this: you are to select this command or option from a menu or take an action of some kind with the menu item. Text that you may need to enter or file names you need to select are show in italic type, such as trail name.
  • Page 18 Notes...
  • Page 19: Section 2: Installation

    Section 2: Installation Preparations You can install the GPS system in some other order if you prefer, but we recommend this installation sequence: Caution: You should read over this entire installation section before drill- ing any holes in your vehicle or vessel! 1.
  • Page 20: Powering Your Display Unit

    To unit The Power/Data cable for this unit. NOTE: There are two basic power connection options, which are shown in the following two diagrams. Read the following instructions carefully to determine which power connection applies to your unit. Depending on your configuration, you may not use all of these wires.
  • Page 21 interference, or if such a switch is not available, we recommend connecting direct to the battery and installing an in-line switch. This will let you shut off power to the power cable when the unit is not in use. When you are not using the unit, you should always shut off power to the power cable, especially when the power cable is disconnected from the unit.
  • Page 22: Power Diagram A

    To unit Display Unit Power Cable Recommended display unit power-off switch Data Cable Use this method if you are powering the display unit and a GPS mod- ule or the display unit and a NMEA 2000 network. (Fuses may be dif- The network and any NMEA 2000 devices, including the GPS module, will not operate unless the NMEA 2000 Power Cable is connected to power.
  • Page 23: Power Diagram B

    To unit All unused Data or NMEA 2000 power wires should be capped with wire nuts and electrical tape to prevent shorts. Data Cable NMEA 2000 Power Cable Use this method if you are only powering your display unit and are not powering a NMEA 2000 network or any NMEA 2000 accessory device, including a GPS module.
  • Page 24: Gps Antenna/Receiver Module

    GPS Antenna/Receiver Module The GlobalMap 540c BAJA package includes the LGC-BAJA GPS mod- ule. This device contains the unit's external antenna and receiver for GPS and WAAS signals. The antenna/receiver module comes with a 15- foot extension cable.
  • Page 25: Nmea 0183 Cable Connections

    If dashboard reception is poor, simply relocate the antenna module else- where on the vehicle for a clearer view of the sky. Connecting to a NMEA 2000 Network A network bus is an installed and operational network cable (backbone) running the length of your boat, already connected to a power supply and properly terminated.
  • Page 26: Nmea 0183 Wiring

    Com-1 wiring to receive NMEA position information from some other Yellow (Transmit) Com-1 To GlobalMap Shield (Ground) 540c Com-1 wiring to transmit NMEA position information to another NMEA-compatible device. NMEA Transmit Ground GPS receiver NMEA Receive Ground To Other GPS Receiver To Other Device...
  • Page 27 Power/Data socket Data cable NMEA 2000 Power cable Display unit power cable LGC-BAJA GlobalMap 540c BAJA Cable Connections. Network socket Double T connector Extension cable Ethernet (future enhancement) Extension cable...
  • Page 28: Mounting The Unit: Bracket Or Portable

    Mounting the Unit: Bracket or Portable You can install the GlobalMap 540c on the top of a dash with the sup- plied gimbal bracket. It can also be mounted on a portable power supply. If you use the supplied bracket, you may be interested in the optional ®...
  • Page 29 Front Install the gimbal bracket. Orient the bracket so the arms slope to- Drill a 1-inch (25.4 mm) hole in the dash for the power cable. The best location for this hole is immediately under the gimbal bracket location. This way, the bracket can be installed so that it covers the hole, holds the cables in position and results in a neat installation.
  • Page 30: Mmc Or Sd Card Memory Card Installation

    to leave enough slack in the cables to allow tilting or swiveling the GlobalMap 540c. If you choose to fill in the hole, be sure to position the cables against the rear edge of the hole as you apply the fill material. Before positioning the bracket, be sure to hold the cables against the rear edge of the hole.
  • Page 31 NOTE: Throughout this manual, we will use the term MMC, but just re- member that your unit can use an MMC or SD card to store data. Both of these solid-state flash memory devices are about the size of a postage stamp.
  • Page 32: Other Accessories

    Other Accessories Cleaning Towel A lint-free microfiber towel is included for cleaning the unit’s screen. The towel is highly effective in clearing away water spots, smudges and finger prints. Just wipe the screen with the dry towel — it's not neces- sary to moisten the towel with water.
  • Page 33 WARNING: When the unit is mounted in an unprotected area, such as an open boat cockpit, the protective face cover must be removed when the vehicle is moving at high speed. This includes towing a boat on a trailer at highway speeds.
  • Page 34 Notes...
  • Page 35: Section 3: Basic Gps Operation

    Section 3: Basic GPS Operation This section addresses the unit's most basic GPS operations. The tuto- rials presented in Sec. 3 follow a chronological order. Sec. 4, Advanced GPS Operations, will discuss other more advanced functions and utili- ties. Before you turn on the unit and find where you are, it's a good idea to learn about the different keys, the four Page screens and how they all work together.
  • Page 36: Power/Lights On And Off

    2. PAGES – Pressing this and the ← → arrow keys (4) switches the unit between the three different page screens. (Satellite Status Page, Navigation Page and Map Page.) Each page represents one of the unit's major operation modes. 3. MENU – Press this key to show the menus and submenus, which allow you to select a command or adjust a feature.
  • Page 37 Cancel Navigation: cancels navigation commands. Used to stop navi- gating after you reach your destination. GPS Setup: sets various GPS receiver options. System Setup: sets general configuration options. NMEA 2000: provides access to all NMEA 2000 network setup options, including the configuration of devices on the network.
  • Page 38: Satellite Status Page

    Browse MMC Files: this allows you to view the installed MMC card and the files it contains. Pages The unit has three Pages that represent the three major operating modes. They are the Satellite Status Page, the Navigation Page and the Map Page.
  • Page 39 North is at the top of the screen. You can use this to see which satellites are obstructed by obstacles in your immediate area if the unit is facing north. The GPS receiver will track satellites that are in bold type. The re- ceiver hasn't locked onto a satellite if the number is grayed out, there- fore it isn't being used to calculate your position.
  • Page 40: Navigation Page

    5. Select the desired subcategory and press checkmark in the checkbox, showing the selected data is set for display. 6. If you want to display other data types, repeat Steps 4 and 5. Press repeatedly to get back to the Custom Gauges page. The data you EXIT selected will now be displayed on the screen.
  • Page 41 Track or compass heading indicator, showing direction of travel Navigation information displays in customizable data boxes Trail line Navigation Page, recording a trail, traveling southwest. Page looks like this when the unit is not navigating to a waypoint, following When navigating to a waypoint, the Navigation screen looks like the following figure.
  • Page 42 Left cross track error line Current track or heading, shown in degrees Compass bearing to destination Trail line Navigation information displays in data boxes Navigation Page, going to a waypoint while creating a new trail. The cross track error range is shown on the compass rose as a wide, white, corridor enclosing the course line.
  • Page 43: Map Page

    The Navigation Page has its own menu, which is used for some ad- vanced functions and for setting various options. (Options and setup are discussed in Sec. 5). To access the Navigation Page Menu, from the Navigation Page, press MENU Map Page The Map Page screens show your course and track from a bird's-eye view.
  • Page 44: Background Map Vs. Mapcreate Map Content

    If you're using only the factory-loaded background map, the maximum zoom range for showing additional map detail is 20 miles. You can con- tinue to zoom in closer, but the map will simply be enlarged without revealing more map content (except for a few major city streets.) Load your own high-detail custom map made with MapCreate (or a pre-made FreedomMap from LEI), and you can zoom in to 0.02 miles with mas- sive amounts of accurate map detail.
  • Page 45 shape of a coastline or water body, but the higher detail in MapCreate shows the shoreline completely and accurately (finer detail). Many smaller islands would not be included in the background map, but are in MapCreate. NOTE: Available through LEI Extras (look inside back cover for accessory ordering information), FreedomMaps are pre-made maps that con- tain all of the same information available in a custom MapCreate map, without any work on your part.
  • Page 46 The Map Page has its own menu, which is used for several functions and for setting various options. To access map display options, press highlight , then select PAGES the desired map page option. Press EXIT Digital Data map page (left). Two Position Formats page (right). In pages that have two major windows (such as two maps) you can tog- back forth...
  • Page 47: Map With Custom Gauges

    1. From any two-window display, press 2. Four flashing arrows appear along the centerline dividing the two windows. The windows will be in a horizontal position by default, so press ↑ ↓ to resize the windows. Or, if you want to realign the windows vertically, use ←...
  • Page 48: Radar

    5. Select the desired subcategory and press checkmark in the checkbox, showing the selected data is set for display. 6. If you want to display other data types, repeat Steps 4 and 5. Press repeatedly to get back to the Map with Custom Gauges page. The EXIT data you selected will now be displayed in the gray area on the left side of the screen.
  • Page 49 Radar Page (left) with Radar menu display (right). To access Radar Page: 1. Press , highlight the tab and press PAGES ADAR 2. Press to open the Radar menu. Press to return to the ra- MENU EXIT dar display. The following page contains a 12-step quick reference for the most basic GPS operations.
  • Page 50: Basic Gps Quick Reference

    Basic GPS Quick Reference Start outdoors, with a clear view of the open sky. As you practice, try navi- gating to a location at least a few blocks away. Navigation in too small an area will constantly trigger arrival alarms. 1.
  • Page 51: Find Your Current Position

    Find Your Current Position Finding your current position is as simple as turning on the unit. With- out obstruction from dense foliage, terrain or structures, the unit auto- matically searches for satellites and calculates its position in approxi- mately one minute or less. If for some reason satellite acquisition takes longer, you may be inside a structure or vehicle or in terrain that is blocking signal reception.
  • Page 52: Selecting Any Map Item With The Cursor

    Cursor line Selected airport The selected airport to the northwest is 4.2 miles away. Selecting Any Map Item With the Cursor 1. Use the zoom keys and the arrow keys to move around the map and find the item you wish to select. 2.
  • Page 53 After the unit has acquired a position: 1. Press |↓ to POI-R 2. You could search the entire restaurant category, but in this example we will narrow our search. Press → to |↓ to HAINS 3. The unit says it is calculating, then a list of restaurants appears, with the closest highlighted at the top of the list.
  • Page 54: Set A Waypoint

    5. The POI information screen appears. If you wanted to navigate there, you could press Enter, since the Go To Waypoint command is highlighted. But we just want to see it on the map, so press ↓ to 6. The unit's map appears, with the cursor crosshairss highlighting the restaurant's POI symbol.
  • Page 55: To Create And Save A Waypoint

    You can copy waypoints from your unit to your personal computer with MapCreate software. When you want to repeat a trip, these archived waypoints can be reloaded into your GPS unit. To create and save a Waypoint: These first two techniques use the Quick Save method, the fastest and easiest way to create a waypoint.
  • Page 56: Create Waypoint On Map

    NOTE: The Quick Save method uses the default waypoint symbol until you edit an existing waypoint and change its symbol. (Edit Waypoint Symbol is described in Sec. 4.) After you have changed a waypoint symbol, the unit will remember the one you chose and use it the next time you save a waypoint.
  • Page 57: Set Man Overboard (Mob) Waypoint

    Course line (dotted) Off course range, set at 0.20 mile Navigation Page, navigating toward waypoint 004 and leaving a trail. Set Man Overboard (MOB) Waypoint One of boating's most terrifying events is having a friend or family member fall overboard. This situation can be deadly on any body of wa- ter.
  • Page 58: Navigate To Cursor Position On Map

    Navigating to Man Overboard: Man Overboard Activated message (left). Navigation Page, center, Map Page (right). The victim is to the starboard of the vessel. The GPS shows which direction to go for the rescue. The man overboard position is also stored in the waypoint list for fu- ture reference.
  • Page 59: Navigate To A Point Of Interest

    Navigate to cursor. In this example, the cursor is centered on Oologah, Oklahoma. 3. Press and the unit will begin navigating to the cursor MENU location. The Map Page will display a dotted line from your current position to the cursor position.
  • Page 60: Creating And Saving A Trail

    The other method involves searching for POIs with the Find Waypoint command, launched with the To Navigate to a POI: 1. Press , select the desired POI category, then press → to Subcate- gory. 2. Highlight the desired subcategory and press .
  • Page 61 Active symbol Visible symbol Sequence for saving a trail and beginning a new one. Left, My Trails command. Center, the Trails Menu. The arrow to the right of Trail 1 indicates the trail is "active," and the check to the left indicates the trail is visible on the map display.
  • Page 62: Displaying A Saved Trail

    You can save and recall up to 10 different plot trails, which can be cop- ied to your MMC for archiving or for transfer to your MapCreate soft- ware. Another quick way to stop recording one trail and begin a new one is to use the New Trail command: Press RAILS Caution:...
  • Page 63: Visual Trailing

    you are running a trail forward (from start to end) or backward (from end to start.) However, visual trailing provides no navigation informa- tion during the trip, such as the time to your destination. The other two methods provide a full range of navigation data and work with both the Map Page and Navigation Page.
  • Page 64 6. When you reach your destination, be sure to cancel your navigation: press |↓ to MENU MENU sure; press ←| Navigate a trail menu sequence: Fig. 1, My Trails command. Fig. 2, Trails Menu. Fig. 3, Edit Trail Menu. Fig. 4, Edit Route Menu with Navigate command highlighted for Trail 6.
  • Page 65: Navigate A Back Trail (Backtrack, Or Reverse)

    Present position arrow Trail point Navigate trail, map views: Driver is northbound heading straight to- ward trail point 6 (left). Northbound driver has reached point 6 and has turned west to follow trail (right). Track or compass heading indicator Trail waypoint symbol Course...
  • Page 66: Transfer Custom Maps And Gps Data Files

    NOTE If you are already located at or near the end of your trail, the arri- val alarm will go off as soon as you hit alarm and proceed. 5. Now, begin navigating with your unit. 6. When you reach your destination, be sure to cancel your navigation: press |↓...
  • Page 67 Transfer My Data highlighted on System Setup menu (left). When transferring data (right) you will have the option of transferring the unit's data to a MMC card or loading the data on the MMC card into 3. Saving to MMC: To accept the default name "Data" for the GPS Data File, press ↓...
  • Page 68: Cancel Navigation

    The unit will display a completion message when the data transfer is finished. To return to the Page view, press Figure 1. Figure 3. These figures show the menu sequence for loading a GPS Data File from an MMC into the unit's memory. Cancel Navigation You can turn off any of the navigation commands after you reach your destination or at any other time by using the Cancel Navigation com-...
  • Page 69: Section 4: Advanced Operations

    Section 4: Advanced Operations Find Distance from different Locations 1. While on the Map Page press: 2. Center your cursor over the position you want to find the distance to. A rubber band line appears, connecting your current position to the cursor's location.
  • Page 70: Create Icon On Map

    These are sometimes referred to as event marker icons. This unit has 63 different symbols you can pick from when creating an icon. Icons are similar to waypoints, but they do not store as much informa- tion (like names) as waypoints do. You can't use a menu to navigate to icons as you can with waypoints.
  • Page 71: Navigate To An Icon

    Delete icons menu. The Delete All Icons command will ask if you are sure. Press ← to . All icons will be deleted from the map. The Delete by Symbol command will launch the Select Symbol menu. Press ← or ↑ or → or ↓ to select the icon symbol to delete, then press .
  • Page 72: Create And Save A Route

    waypoint. Once programmed into the GPS unit, a route provides the option of navigating forward through the route waypoints or in reverse order (you can even begin navigating in the middle of a route!) Create and Save a Route You have the option of creating and editing a route in the unit or you can make a route on your computer with our MapCreate 6 software.
  • Page 73 Edit Route menu (left). Edit Route Waypoints menu (right) with Add From Map command selected. 3. Use the Zoom keys and arrow keys to move the map and cursor until the cursor is centered on the spot where you want your route to begin. (If you are starting at your current position or the current cursor posi- tion, you are already at the starting spot.) 4.
  • Page 74: Delete A Route

    Route creation sequence, continued: Fig. 4. Point (3) set at on-ramp turn. Fig. 5. Waypoint (4) set at highway exit to frontage road leading to river. Waypoint (5) ends the route at a tree stand in the hunting area. Fig. 6. Press EXIT to save the route and you return to this screen. 5.
  • Page 75: Edit Route Waypoints

    3. Press ↑ or ↓ to change the first character, then press → to move the cursor to the next character and repeat until the name is correct, then press . Return to the previous page by pressing Edit Route Waypoints You can edit the route by adding and removing waypoints.
  • Page 76: Navigate A Route In Reverse

    Route Planning on Main Menu (left). Routes menu (center). Edit Route menu (right). Navigate is selected on Edit Route menu. 2. Press ↓ to select route name| 3. Upon arrival at your destination, cancel navigation: press |↓ to MENU MENU The following figures show what the Navigation Page and Map Page look like while navigating a route.
  • Page 77: Trails

    Figure 1. Figure 3. Navigating along a route: Fig. 1 shows the Navigation Page at the start of a route, heading straight for the first waypoint (Wpt 1). In Fig. 2, the traveler has arrived at Wpt 1; the arrival alarm has been triggered and the bearing arrow on the compass rose has turned to point toward Wpt 2, off to the east.
  • Page 78: Edit A Trail Name

    Edit a Trail Name To edit a trail name: press name| . Press ↑ or ↓ to change the first character, then press → to the next character and repeat until the name is correct. Press then repeatedly to return to the previous page display. EXIT Tip: You can quickly call up the Edit Trail menu by selecting a trail on...
  • Page 79: Utilities

    Edit Trail Menu with Pattern option selected (left). Edited trail with Utilities Utilities are useful tools for traveling or for outdoor activities. Alarm Clock To access the unit's alarm clock: press LARM LOCK Sun/Moon Rise & Set Calculator To get to the Sun/Moon menu: press LATIONS Trip Calculator To get to the Calculator menu: press...
  • Page 80: Edit A Waypoint

    To delete a waypoint from the map: 1. Use the arrow keys to select the waypoint with the cursor. 2. Press |↓ to previous page and clear the cursor, press To delete all waypoints at one time: 1. Press MENU MENU |←...
  • Page 81: Selecting A Waypoint

    Selecting a Waypoint To select a waypoint on the map (for navigating to, for editing, etc.,) use the arrow keys and center the cursor over the waypoint. A highlighted halo will appear around the waypoint. Create Waypoint by Entering a Position 1.
  • Page 82: Set A Waypoint By Average Position

    Set a Waypoint by Average Position This feature sets a waypoint at the current position after taking several position readings and averaging them. This boosts waypoint position accuracy by helping to eliminate errors caused by atmospheric condi- tions and other factors. 1.
  • Page 83: Section 5: System & Gps Setup

    Section 5: System & GPS Setup Alarms This unit has several GPS alarms. The factory default setting has all of these but the anchor alarm turned on. You can turn the alarms off and on and change their distance settings. You can set an arrival alarm to flash a warning message and sound a tone when you cross a preset distance from a waypoint.
  • Page 84: Auto Satellite Search

    Auto Satellite Search To lock on to the satellites, the GPS receiver needs to know its current position, UTC time and date. (Elevation [altitude] is also used in the equation, but it's rarely required to determine a position.) It needs this data so that it can calculate which satellites should be in view.
  • Page 85: Check Mmc Files And Storage Space

    Check MMC Files and Storage Space To check MMC Files: 1. Press MENU MENU 2. Use ↑ ↓ to browse through files on the MMC card. Highlight the de- sired file and press 3. Press repeatedly to return to the main display. EXIT Communications Port Configuration The unit has one NMEA 0183 version 2.0 compatible communication...
  • Page 86: Configure Nmea

    For connectors and wiring information for another device, see page 18. For assistance in configuring the unit to communicate with another device, consult the factory. Customer service phone numbers are in the back of this manual. Configure NMEA You can configure the unit to use specific NMEA sentences. 1.
  • Page 87 (Universal Transverse Mercator) projection; MGRS (Standard); MGRS (Standard + 10); Map Fix; Loran TD; British, Irish, Finnish, German, New Zealand, Swedish, Swiss, Taiwan and Greek. UTM's are marked on USGS topographic charts. This system divides the Earth into 60 zones, each 6 degrees wide in longitude. British, Irish, Finnish, German, New Zealand, Swedish, Swiss, Taiwan, and Greek grid systems are the national coordinate system used only in their respective countries.
  • Page 88: Map Fix

    Configure Loran TD menu. Map Fix Map Fix is used with charts or maps. This system asks for a reference position in latitude/longitude, which you take from a marked location on the map. It then shows the present position as distance on the map from that reference point.
  • Page 89: Customize Page Displays

    4. Press and enter the map's scale. This is generally at the bottom of the paper map. It is shown as a ratio, like 1:24000. Press the unit to return to the Configure Map Fix screen. Configure a map fix so the unit can find your position on a printed 5.
  • Page 90: Gps Simulator

    You will see a list of categories with "+" or "–" symbols next to each cate- gory. A category with a "+" is expandable, meaning its contents are hid- den. Customize Menu, with "GPS Data" and "Navigation" categories expanded. Selecting the category name and pressing contents, so you can choose items within it.
  • Page 91 To turn on the GPS Simulator: 1. Press MENU MENU 2. Select IMULATORS The GPS Simulator page will appear. The page has dialog boxes that allow you to change the Track, Speed, Altitude, Latitude and Longitude of your simulation. You can begin your simulation at a waypoint by using the Select Start- ing Waypoint command or direct the simulation manually by using the Steer with Arrows command, which will place Steer with Arrow boxes on the main display.
  • Page 92: Initialize Gps

    Steer with Arrows When you are using the Steer with Arrows command, you can press to clear the steering and speed boxes from the screen while con- EXIT tinuing the simulation. This action will allow you to use the map cursor during a simulation.
  • Page 93: Map Auto Zoom

    Map Auto Zoom This unit has an auto zoom feature that eliminates much of the button pushing common with other brands of GPS receivers. It works in con- junction with the navigation features. First, start navigation to a waypoint. (See the waypoint section for more information on navigating to a waypoint.) Then, with the auto zoom mode on, the unit zooms out until the entire course shows, from the present position to the destination waypoint.
  • Page 94 To turn on/off Pop-up Map Information 1. From the Map Page, press 2. Press ↓ to OPUP to check it (turn on) or uncheck it (turn off.) 3. After the option is set, press To turn on/off Draw Map Boundaries 1.
  • Page 95: Map Datum Selection

    To turn on/off Lat/Long Grid lines: 1. From the Map Page, press 2. Press ↓, to to check it (turn on) and uncheck it (turn off.) 3. After the option is set, press Map Datum Selection Maps and charts are based on a survey of an area covered by the map or chart.
  • Page 96: Map Orientation

    To access Map Categories: 1. From the Map Page, press 2. Press to select a category or press ↑ ↓ subcategory. Press 3. To return to the map display, press The Map Categories Drawn Menu. Map Orientation By default, this receiver shows the map with north always at the top of the screen.
  • Page 97: Nauticpath™ Usa Marine Charts

    the right side of the map, and so on. However, if you travel any other direction, the map doesn't line up with your view of the world. To correct this problem, a track-up mode rotates the map as you turn. Thus, what you see on the left side of the screen should always be to your left, and so on.
  • Page 98: Port Information

    NauticPath chart showing Chart Note icon selected by cursor (left). Note information screen (right). To view Chart Note information: 1. Use the arrow keys to move the cursor over a Chart Note icon. When it's selected, a pop-up name box appears. 2.
  • Page 99: Tidal Current Information

    To view Port Services information: 1. Use the arrow keys to move the cursor over a Port Services icon. When it is selected, a pop-up name box appears. 2. Press to display the Port Services Information screen. Port Services icon NauticPath chart showing Port Services icon selected by cursor.
  • Page 100: To View Tidal Current Information

    When you zoom in to a sufficiently small zoom range (0.8 nautical mile), the icon becomes an animated arrow showing tidal current veloc- ity and direction for the selected tidal station at the present time. At larger zoom ranges, you can select the boxed "C" icon and it becomes an animated arrow with a pop-up name box (the name box disappears af- ter a few seconds).
  • Page 101: Tide Information

    the screen is an approximate view of the flood and ebb pattern for the day, from midnight (MN), to noon (NN) to midnight (MN). The velocity scale at the top left side of the graph changes dynamically based upon the maximum velocity of the current for that day. Slack water, the period of little or no current, is represented by the Slack Water Line (SWL).
  • Page 102: Navionics ® Charts

    To view tide information: 1. Use the arrow keys to move the cursor over a tide station icon. When it is selected, a pop-up name box appears. 2. Press to display the Tide Information screen. MLLW Line Tide Table The Tide Information screen displays daily tidal data for this station on this date at the present time.
  • Page 103: Overlay Data

    play. NauticPath charts are ready for display as soon as they are inserted into the unit. Navionics charts must be inserted into the unit, then selected as a Map Choice option in the Map Data menu. To display a Navionics chart: 1.
  • Page 104: To Overlay Information On Your Screen

    Overlay Data Shown menu (left) with Press Ent to add highlighted. Over- lay Data with Navigation category expanded. To overlay information on your screen: 1. Press |↓ to MENU VERLAY 2. If you currently have any overlay data on your screen, it will be listed here.
  • Page 105: To Remove Overlaid Data

    Data Viewer (left). Navigation category expanded with Bearing and Distance selected (center). Bearing and Distance displayed on Overlay To remove overlaid data: 1. While on the Page that shows the item or items you want to remove, press |↓ to MENU VERLAY 2.
  • Page 106 To move overlaid data: You may find it useful to move or rearrange overlay data on your dis- play. 1. From one of the Map Pages, press 2. You will see a list of the overlay data currently displayed. Select the item you want to move and press 3.
  • Page 107: Pop-Up Help

    NOTE: Some data types can be displayed in only one font size. If that is the case, the Data Size box will not be displayed for that data type. Pop-up Help Help is available for virtually all menus in this unit. By leaving a menu item or command highlighted for a few seconds, a pop-up message will appear, giving a brief description of the functions purpose.
  • Page 108: Screen Contrast And Brightness

    Reset Options highlighted on the System Setup menu (left). Reset Op- tions confirmation message (right). Screen Contrast and Brightness To adjust Contrast: 1. Press MENU MENU 2. Highlight ONTRAST bar. The left end of the scale is the lowest contrast level. The right end is the highest contrast level.
  • Page 109: Set Language

    To adjust the screen's display mode: 1. Press MENU MENU 2. Press ↓ to ISPLAY with three options: Normal, High Contrast and Night Viewing. 3. Select the desired mode and press the map display. Set Language This unit's menus are available in 10 languages: English, French, Ger- man, Spanish, Italian, Danish, Swedish, Russian, Dutch and Finnish.
  • Page 110 To set the Month: 1. Make sure your unit has acquired your position, then press , highlight MENU MENU 2. Highlight OCAL 3. Select ONTH To set the Day: 1. Make sure your unit has acquired your position, then press , highlight MENU MENU...
  • Page 111: Show Waas Alarm

    2. Select OCAL 3. Highlight the ONFIGURE menu, select the country with DST rules that match your region. 4. Press repeatedly to return to the map display. EXIT Show WAAS Alarm When the signal is available, your unit will automatically use WAAS to boost the accuracy of the position fix.
  • Page 112: Sounds And Alarm Sound Styles

    Sounds and Alarm Sound Styles Sounds triggered by key strokes and alarms can be turned off or ad- justed to a desired level. To set Key Press Sounds: 1. Press MENU MENU 2. Highlight RESS check it (turn off. 3. Press to return to the map display.
  • Page 113: Track Smoothing

    Track Smoothing This is a factory setting on the GPS Setup menu that should always be left on. When stopped or traveling at slow speeds (such as walking or trolling), Track Smoothing prevents wandering of trails, the steering arrow, compass rose and a map in track-up mode. Track Smoothing highlighted on the GPS Setup menu.
  • Page 114: Update Trail Option

    To create a New Trail: 1. Press MENU MENU 2. Highlight RAIL allowing you to Edit the trails name, color, pattern, maximum points, trail status (active or inactive) and trail visibility. You can also navi- gate the trail or delete the trail. New Trail selected on the Trails menu (left).
  • Page 115 You can have trail points placed at any distance between 0.01 mile/nm/km to 9.99 mile/nm/km. The default setting is 0.10 mi. WARNING: If you uncheck the Update Trail option, automatic trail creation and recording will be turned off. You must turn it back on to record trails.
  • Page 116: Transparency

    To delete a Trail: 1. Press , select and press MENU MENU RAILS 2. Select the desired trail from the Saved Trails list and press . The Edit Trail menu will appear. 3. Highlight and press . The following message will ap- ELETE RAIL pear: Delete this trail? Select...
  • Page 117: Units Of Measure

    Transparency selected on main menu. Transparency slider bar (right). To adjust Transparency level: 1. Press MENU MENU bar appears. 2. Use ↑ ↓ to move the bar. Move the bar to the bottom of the scale to eliminate transparency. Moving the bar to the top of the scale will pro- vide the greatest level of transparency.
  • Page 118 To set Temperature units: 1. Press MENU MENU will be highlighted, so press 2. Highlight EMPERATURE 3. Use ↑ ↓ to select one of the following options: Fahrenheit, Celsius or Kelvin. Press 4. Press repeatedly to return to the map display. EXIT To set Pressure units: 1.
  • Page 119 4. Press repeatedly to return to the map display. EXIT To set Heading units: 1. Press MENU MENU will be highlighted, so press 2. Highlight EADING 3. Use ↑ ↓ to select one of the following options: True or Magnetic. Press 4.
  • Page 120 Notes...
  • Page 121: Section 6: Searching

    Section 6: Searching NOTE: The background map loaded in your unit's permanent memory lets you search for some land features, including cities and lakes. For a full set of searchable land features, including landmarks, streets, addresses, highway exits and Points of Interest, you must load your own high-detail custom map produced with our MapCreate soft- ware.
  • Page 122 3. To enter a street name, press ↓ to A. You can spell out the name in the top selection box. Press ↑ or ↓ to change the first letter, then press → to move the cursor to the next let- ter and repeat until the name is correct, then press B.
  • Page 123: Find Any Item Selected By Map Cursor

    Find By Name menu with list of cities. Find Any Item Selected by Map Cursor With a POI or map feature selected by the cursor, press to the previous page, press A POI selected by the cursor (left). POI information screen (right). NOTE: Since the Go To Waypoint command is highlighted, you can navi- gate to the selected POI by pressing...
  • Page 124 The Find Exit menu. 2. First, select a highway name by pressing , which calls up the Find By Name menu. There are two highway search options: A. You can spell out the highway name in the top selection box. Press ↑ or ↓ to change the first letter, then press →...
  • Page 125 Find Exit menu with an exit selected in the Exit List. 4. In the Exit Information screen you have two choices. A. Press navigate or "go to" the exit. B. Press →| map. Go To Exit highlighted (left). Find On Map selected (right). Tip: You can also look up some additional information on the Exit Ser- vices located near this exit.
  • Page 126: Find Map Places Or Points Of Interest (Poi)

    Exit Information screen (left). General location and amenities information (right). Find Map Places or Points of Interest (POI) 1. Press , press to select a map place or POI category, then ↓ ↑ press . (To narrow your search, press → then press ↓ or ↑ to select a subcategory before pressing .) You will be given two options;...
  • Page 127 Find by Nearest option, left, Calculating screen, center, POI list, right. 3. To search by the name of a POI: press . There are two options: A. You can spell out the POI in the top selection box. Press ↑ or ↓ to change the first letter, then press →...
  • Page 128: Find Streets Or Intersections

    Go To Waypoint highlighted (left). Find on Map selected (right). Find Streets or Intersections Find a Street 1. From the Map Page, press |↓ to and the Find MENU TREETS Streets Menu appears. 2. You must first fill in a street name in the First Street dialog box. Press to display the Find By Name menu.
  • Page 129: Find An Intersection

    for that street, press ↓ to ing you to wait while the unit finds the street. When the Streets Found list appears, press ↑ or ↓ to select the street you are searching for and press ENT. Find Streets menu with the Find First street highlighted (left). Streets 4.
  • Page 130 2. You must fill in a street name in the First Street dialog box. Press to display the Find By Name menu. There are two options: A. You can spell out the street in the top selection box. Press ↑ or ↓ to change the first letter, then press →...
  • Page 131: Find Waypoints

    ↑ or ↓ to select the intersection you are searching for and press . (In our example, we selected the intersection of SW 80th Street and SW 71st Avenue in Miami, Fla.) 7. The Map Page appears, with the cursor pointing to the found intersec- tion.
  • Page 132 3. If you're looking for nearest, the unit says it is calculating, then a list of waypoints appears. The closest waypoint is highlighted at the top of the list. The waypoint furthest from you is at the bottom of the list. 4.
  • Page 133 Find By Name menu (left). Waypoint Information screen (center). The found waypoint is highlighted by the cursor on the Map Page (right). A. To navigate to the waypoint, press . (Go To Waypoint com- mand is already highlighted.) The unit will show navigation infor- mation to the waypoint.
  • Page 134 Notes...
  • Page 135: Section 7: Nmea 2000

    Section 7: NMEA 2000 NMEA 2000 Menu The NMEA 2000 menu on your display unit's main menu allows you to configure, calibrate and monitor devices on a NMEA 2000 network. The NMEA 2000 menu provides access to the Bus Setup, Fuel Management and NMEA 2000 Alarms.
  • Page 136: Engine & Tank Configuration

    The NMEA Diagnostics page displays information about the perform- ance of the network bus, keeping you updated on bus status, mode, er- rors and bus traffic. The Ethernet Diagnostics page keeps you updated on the performance of an Ethernet connection (if applicable) supplying information ranging from IP Address to upload and download rates (bytes per second).
  • Page 137: Tank Select

    figuration you will use the Tank Select menu, Tank Size dialog box and Set configuration button, all detailed below. Tank Select The Tank Select menu allows you to choose from up to three tanks (Port, Center and Starboard), depending on the Engine-tank configura- tion that has been selected.
  • Page 138: Device Configuration Menu

    6. Select the tank you want to set up and press . Press → to high- light the Tank Size dialog box and press 7. Use ↓ ↑, ← → to input the capacity (gallons) of the tank you chose from the Tank Select menu and press 8.
  • Page 139: Fuel Management Menu

    data window will include tank size and the amount of fuel left in the tank. The Device Data for an EP-10 Fuel Flow includes Fuel Rate (amount of fuel burned per hour), Fuel Used, Trip Fuel Used and Sea- sonal Fuel Used. NOTE: If, as in the graphic above, you do not have a Suzuki Engine Inter- face, EP-15 Fluid Level or EP-10 Fuel Flow on the network, the...
  • Page 140: Add Fuel

    Add Fuel After entering the amount of fuel added to a tank in the Fuel Added dialog, the Add Fuel command finalizes the entry of the data. Like the Fuel Added dialog, the Add Fuel command will only be used when an amount of fuel is added that does not fill up the tank.
  • Page 141: Nmea 2000 Alarms

    To Reset Calibration: Choosing the Reset Calibration command will switch fuel flow calibra- tion settings back to factory defaults. 1. Press MENU MENU 2. Highlight menu will appear. 3. Highlight to NGINE the engine attached to the desired fuel flow — and press 4.
  • Page 142: Waypoint Sharing

    current status will be shown on the Alarm Status window. To view the Alarm Status window, highlight the Alarm Status tab and press To set NMEA 2000 Alarm: 1. Press MENU MENU 2. Highlight NMEA 2000 A 3. Highlight LUID vice you want to set an alarm for and press 4.
  • Page 143: Configuring Ep Sensors

    Configuring EP Sensors All configurable devices are configured through their Device Configura- tion menus, which may be accessed through the network devices list on the Bus Configuration menu. EP-35 Temperature Configuration To input Device Name: 1. Press MENU MENU NMEA 2000 menu will appear with five options: Bus Setup, Fuel Man- agement, NMEA 2000 Alarms, Waypoint Sharing and Backlight Syn- chronization.
  • Page 144: Instance

    Instance The Instance command is intended for use only by experienced NMEA 2000 network technicians. Instance allows network technicians to re- solve certain electronic probe conflicts. This is most likely to occur if the network includes LMF-200 or LMF-400 digital gauges, which do not support the display of as many electronic probes as your GlobalMap.
  • Page 145: Advanced Options Menu

    3. Select the fuel flow you want to rename and press Configuration menu will appear with the Device Name dialog box high- lighted. and use ↑ ↓, ← → to input the desired name for the fuel 4. Press ENTER flow.
  • Page 146: Ep-15 Fluid Level Configuration

    Fuel Flow will be reset to factory defaults. Other fuel flows on the net- work will not be affected. To restore default settings: 1. Press MENU| MENU NMEA 2000 menu will appear with five options: Bus Setup, Fuel Man- agement, NMEA 2000 Alarms, Waypoint Sharing and Backlight Syn- chronization.
  • Page 147 4. Highlight NSTANCE stance menu with the following options: Tank 1, Tank 2, Tank 3 and Unknown. 5. Select the desired Tank Instance (location) and press lowing confirmation message will appear: Are you sure you wish to change this device's configuration? 6.
  • Page 148: Advanced Options Menu

    Advanced Options menu The Fuel Flow sensor Advanced Options menu contains two categories: Instance and Restore Defaults. Instance The Instance command is intended for use only by experienced NMEA 2000 network technicians. Instance allows network technicians to re- solve certain electronic probe conflicts. This is most likely to occur if the network includes LMF-200 or LMF-400 digital gauges, which do not support the display of as many electronic probes as your GlobalMap.
  • Page 149: Suzuki Engine Interface Configuration

    Suzuki Engine Interface Configuration To input Device Name: 1. Press MENU| MENU NMEA 2000 menu will appear with five options: Bus Setup, Fuel Man- agement, NMEA 2000 Alarms, Waypoint Sharing and Backlight Syn- chronization. 2. Highlight ETUP ration menu. A list of network devices will be at the top of the page. 3.
  • Page 150: Advanced Options Menu

    5. Select your engine type and press appear: Are you sure you wish to change this device's configuration? 6. Highlight and press main display. Advanced Options menu The Engine Interface Advanced Options menu contains three catego- ries: Instance, Restore Defaults and Reset Trim Calibration. Instance The Instance command is intended for use only by experienced NMEA 2000 network technicians.
  • Page 151: Calibrating Ep Sensors

    NOTE: The Suzuki Engine Interface Device Configuration menu contains two Engine Trim calibration commands, which will be addressed in the next segment of this section, Calibrating EP Sensors. Calibrating EP Sensors The factory calibration settings for the EP-10 Fuel Flow, EP-15 Fluid Level and Suzuki Engine Interface should be adequate for the majority of applications, so calibration will not be necessary in most cases.
  • Page 152: Ep-15 Fluid Level Calibration

    To calibrate an EP-10 Fuel Flow: 10. If calibration is necessary, press press 11. Highlight 12. Select OCATION connected to selected fuel flow. Press 13. Highlight pear: Are you sure you wish to Fill Tank? Select 14. The following message will appear: Do you wish to re-calibrate the device? Select and press 15.
  • Page 153: 3-Point Calibration

    3. Select the EP-15 Fluid Level and press 4. Press ↓ to select menu will appear. Instructions on Calibration will be listed at the top of the menu. 5. Highlight Select F , press ENT, then select E LUID EVEL 7.
  • Page 154: 5-Point Calibration

    4. Press ↓ to select menu will appear. 5. Highlight Make sure your tank is empty, then highlight Select E MPTY LEVEL Select ALIBRATE Empty Level Calibration Completed. Press Add half a tank of fuel, highlight and press ALF LEVEL Select ALIBRATE Half Level Calibration Completed.
  • Page 155: Fuel Flow Calibration In A Suzuki Engine Interface

    1. Press MENU| MENU 2. Highlight ETUP ration menu. A list of network devices will be at the top of the page. 3. Select the desired EP-15 Fluid Level and press 4. Press ↓ to select menu will appear. 5. Highlight Make sure your tank is empty, then highlight .
  • Page 156: Engine Trim Calibration

    1. After selecting Fuel Used as overlay data, fill up your tank and press MENU MENU 2. Select NMEA 2000 3. Highlight press 4. Use ↑ ↓ to select the location (Port, Center or Starboard) of the en- gine interface you want to calibrate and press 5.
  • Page 157: Reset Trim Calibration

    3. Highlight ALIBRATE dow will appear with a list of Calibration Instructions. 4. Highlight TART will appear: Please fully raise the Engine Trim. 5. After engine trim has been fully raised, press message will appear: Please fully lower the Engine trim. 6.
  • Page 158 Reset Calibration highlighted (left). Reset Calibration confirmation To Reset Calibration: 1. Press MENU MENU 2. Highlight 3. Highlight NGINE appear with up to four options: All Engines, Port, Center and Star- board. Selecting All Engines will reset calibration for all engines back to factory defaults.
  • Page 159: Sec. 8: Supplemental Material

    Sec. 8: Supplemental Material Datums Used by This Unit WGS 1984 Default Adindan Mean for Ethiopia, Sudan Adindan Burkina Faso Adindan Cameroon Adindan Ethiopia Adindan Mali Adindan Senegal Adindan Sudan Afgooye Somalia Ain el Abd 1970 Bahrain Ain el Abd 1970 Saudi Arabia Anna 1 Astro 1965 Cocos Islands...
  • Page 160 Chatham Island Astro 1971; New Zealand (Chatham Island) Chua Astro Paraguay Corrego Alegre Brazil Dabola Guinea Djakarta (Batavia) Indonesia (Sumatra) DOS 1968 New Georgia Islands (Gizo Island) Easter Island 1967 Easter Island European 1950 Mean for Austria, Belgium, Denmark, Finland, France, West Germany, Gi- braltar, Greece, Italy, Luxembourg, Nether-...
  • Page 161 Nahrwan United Arab Emirates Naparima BWI Trinidad & Tobago North American 1927 Mean for Antigua, Barbados, Barbuda, Caicos Islands, Cuba, Dominican Republic, Grand Cayman, Jamaica, Turks Islands North American 1927 Mean for Belize, Cos- ta Rica, El Salvador, Guatemala, Hondu- ras, Nicaragua North American 1927 Mean for Canada...
  • Page 162 Point 58 Sweden Santo (DOS) 1965 Espirito Santo Island Sao Braz Azores (Sao Miguel, Santa Maria Islands) Sapper Hill 1943 East Falkland Island Schwarzeck Nambia Selvagem Grande Salvage Islands SGS 85 Soviet Geodetic Sys- tem 1985 South American 1969 Mean for Argentina, Bolivia, Brazil, Chile, Colombia, Ecuador, Guyana, Paraguay,...
  • Page 163 Notes...
  • Page 164 Notes...
  • Page 165 Notes...
  • Page 166: Fcc Compliance

    FCC Compliance This device complies with Part 15 of the U.S. Federal Communi- cations Commission (FCC) Rules. Operation is subject to the fol- lowing two conditions: (1) this device may not cause harmful inter- ference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
  • Page 167 LOWRANCE DATABASES LICENSE AGREEMENT THIS IS A LEGAL AGREEMENT BETWEEN THE END-USER WHO FIRST PURCHASES THIS PRODUCT AS A CONSUMER ITEM FOR PERSONAL, FAMILY, OR HOUSEHOLD USE ("YOU") AND LOWRANCE ELECTRONICS, INC., THE MANUFACTURER OF THIS PRODUCT ("WE", "OUR", OR "US"). USING THE PRODUCT ACCOMPANIED BY THIS LICENSE AGREEMENT CONSTITUTES ACCEPTANCE OF THESE TERMS AND CONDITIONS.
  • Page 168: Databases Limited Warranty

    DATABASES LIMITED WARRANTY "We", "our", or "us" refers to Lowrance Electronics, Inc., the manufacturer of this product. "You" or "your" refers to the first person who purchases the prod- uct as a consumer item for personal, family, or household use. The Databases Limited Warranty applies to the one or more databases that your product may contain.
  • Page 169 LOWRANCE ELECTRONICS FULL ONE-YEAR WARRANTY "We," "our," or "us" refers to LOWRANCE ELECTRONICS, INC., the manufacturer of this product. "You" or "your" refers to the first person who purchases this product as a consumer item for personal, family or household use. We warrant this product against defects or malfunctions in materials and workmanship, and against failure to conform to this product's written specifications, all for one (1) year from the date of original purchase by you.
  • Page 170: How To Obtain Service

    How to Obtain Service… …in the USA: We back your investment in quality products with quick, expert service and genuine Lowrance parts. If you're in the United States and you have technical, return or repair questions, please contact the Factory Customer Service Department.
  • Page 171: Accessory Ordering Information

    Accessory Ordering Information for all countries To order Lowrance GPS accessories such as power cables or MMC cards, please contact: 1) Your local marine dealer, sporting goods or consumer electronics store. Most quality dealers that handle marine electronic equipment or other consumer electronics should be able to assist you with these items.
  • Page 172: Visit Our Web Site

    Visit our web site: Lowrance Pub. 988-0151-481 © Copyright 2006 All Rights Reserved Printed in USA 120506 Lowrance Electronics, Inc.

Table of Contents