Wireless-G Broadband Router Table of Contents Chapter 1: Introduction Welcome What’s in this Guide? Chapter 2: Planning Your Wireless Network Network Topology Ad-Hoc versus Infrastructure Mode Network Layout Chapter 3: Getting to Know the Wireless-G Broadband Router The Back The Front Panel Chapter 4: Connecting the Wireless-G Broadband Router Hardware Installation for Connection to Your Broadband Modem Chapter 5: Configuring the PCs...
Page 4
Wireless-G Broadband Router The Applications and Gaming Tab - DMZ The Administration Tab - Management The Administration Tab - Log The Administration Tab - Factory Defaults The Administration Tab - Firmware Upgrade The Status Tab - Router The Status Tab - Local Network The Status Tab - Wireless Appendix A: Troubleshooting Common Problems and Solutions...
Page 5
Wireless-G Broadband Router List of Figures Figure 3-1: The Broadband Router’s Back Panel Figure 3-2: The Broadband Router’s Front Panel Figure 4-1: Connecting Your Internet Connection Figure 4-2: Connecting Your Network Devices Figure 4-3: Connecting the Power Figure 5-1: Configuration Tab Figure 5-2: IP Address Tab Figure 5-3: Properties Figure 5-4: TCP/IP...
Chapter 1: Introduction Welcome Thank you for choosing the Linksys Wireless-G Broadband Router. The Wireless-G Broadband Router will allow you to network wirelessly better than ever, sharing Internet access, files and fun, easily and securely. How does the Wireless-G Broadband Router do all of this? A router is a device that allows access to an Internet connection over a network.
Wireless-G Broadband Router What’s in this Guide? This user guide covers the steps for setting up and using the Wireless-G Broadband Router. • Chapter 1: Introduction This chapter describes the Router’s applications and this User Guide. • Chapter 2: Planning Your Wireless Network This chapter describes the basics of wireless networking.
Page 9
• Appendix I: Regulatory Information This appendix supplies the regulatory information regarding the Router. • Appendix J: Contact Information This appendix provides contact information for a variety of Linksys resources, including Technical Support. Chapter 1: Introduction What’s in this Guide?
Wireless-G Broadband Router Chapter 2: Planning Your Wireless Network Network Topology A wireless local area network (WLAN) is exactly like a regular local area network (LAN), except that each computer in the WLAN uses a wireless device to connect to the network. Computers in a WLAN share the same frequency channel and SSID, which is an identification name shared by the wireless devices belonging to the same wireless network.
Page 11
Linksys's switches (such as the EZXS55W or EZXS88W). With these, and many other, Linksys products, your networking options are limitless. Go to the Linksys website at www.linksys.com/international for more information about products that work with the Wireless-G Broadband Router.
Wireless-G Broadband Router Chapter 3: Getting to Know the Wireless-G Broadband Router The Back The Broadband Router's ports, where the cables are connected, are located on the back panel. Figure 3-1: The Broadband Router’s Back Panel Reset Button There are two ways to reset the Broadband Router's factory defaults. Either press the Reset Button, for approximately five seconds, or restore the defaults from the Administration tab - Factory Defaults in the Broadband Router's Web-based Utility.
Wireless-G Broadband Router The Front Panel The Router’s LEDs, where information about network activity is displayed, are located on the front panel. Figure 3-2: The Broadband Router’s Front Panel Power Green. The Power LED lights up and will stay on while the Router is powered on. When the Router goes through its self-diagnostic mode during every boot-up, this LED will flash.
Wireless-G Broadband Router Chapter 4: Connecting the Wireless-G Broadband Router Hardware Installation for Connection to Your Broadband Modem 1. Power down your network devices. 2. Locate an optimum location for the Broadband Router. The best place for the Broadband Router is usually at the center of your wireless network, with line of sight to all of your mobile stations.
Wireless-G Broadband Router 5. Connect your network PCs or Ethernet devices to the Broadband Router’s numbered ports using standard Ethernet network cabling. Figure 4-2: Connecting Your Network Devices 6. Connect the AC power adapter to the Broadband Router's Power port and the other end into an electrical outlet.
Wireless-G Broadband Router Chapter 5: Configuring the PCs Overview The instructions in this chapter will help you configure each of your PCs, so they will be able to communicate with the Router. To do this, you need to configure your PC’s network settings to obtain an IP (or TCP/IP) address automatically, so your PC can function as a DHCP client.
Wireless-G Broadband Router Configuring Windows 2000 PCs 1. Click the Start button. Select Settings and click the Control Panel icon. Double-click the Network and Dial-up Connections icon. 2. Select the Local Area Connection icon for the applicable Ethernet adapter (usually it is the first Local Area Connection listed).
Wireless-G Broadband Router Configuring Windows XP PCs The following instructions assume you are running Windows XP with the default interface. If you are using the Classic interface (where the icons and menus look like previous Windows versions), follow the instructions for Windows 2000.
Administration tab’s Management screen.) Then click the OK button. Chapter 6: Configuring the Wireless-G Broadband Router Overview NOTE: For first-time installation, Linksys recommends that you use the Setup Wizard on the Setup CD-ROM. If you want to configure advanced settings, use this chapter to learn about the Web- based Utility.
Wireless-G Broadband Router The Setup Tab - Basic Setup The first screen that appears displays the Setup tab. This allows you to change the Broadband Router's general settings. Change these settings as described here and click the Save Settings button to apply your changes or Cancel Changes to cancel your changes.
Wireless-G Broadband Router • PPPoE. Some DSL-based ISPs use PPPoE (Point-to-Point Protocol over Ethernet) to establish Internet connections. If you are connected to the Internet through a DSL line, check with your ISP to see if they use PPPoE. If they do, you will have to enable PPPoE. User Name and Password.
Wireless-G Broadband Router • HeartBeat Signal. HeartBeat Signal (HBS) is a service that applies to connections in Australia only. User Name and Password. Enter the User Name and Password provided by your ISP. Heart Beat Server. This is the IP address that the Router has, when seen from the Internet. Your ISP will provide you with the IP Address you need to specify here.
Wireless-G Broadband Router Router IP This presents both the Router’s IP Address and Subnet Mask as seen by your network. Figure 6-9: Router IP Network Address Server Settings (DHCP) The settings allow you to configure the Router’s Dynamic Host Configuration Protocol (DHCP) server function. The Router can be used as a DHCP server for your network.
Wireless-G Broadband Router The Setup Tab - DDNS The Router offers a Dynamic Domain Name System (DDNS) feature. DDNS lets you assign a fixed host and domain name to a dynamic Internet IP address. It is useful when you are hosting your own website, FTP server, or other server behind the Router.
Wireless-G Broadband Router The Setup Tab - MAC Address Clone A MAC address is a 12-digit code assigned to a unique piece of hardware for identification. Some ISPs will require you to register a MAC address in order to access the Internet. If you do not wish to re-register the MAC address with your ISP, you may assign the MAC address you have currently registered with your ISP to the Router with the MAC Address Clone feature.
Wireless-G Broadband Router The Setup Tab - Advanced Routing This tab is used to set up the Router’s advanced functions. NAT allows mulitple uses to share one Internet connection. Dynamic Routing will automatically adjust how packets travel on your network. Static Routing sets up a fixed route to another network destination.
(use any of the characters on the keyboard). Make sure this setting is the same for all points in your wireless network. For added security, you should change the default SSID (linksys) to a unique name. Wireless Channel. Select the appropriate channel from the list provided to correspond with your network settings.
Wireless-G Broadband Router The Wireless Tab - Wireless Security The Wireless Security settings configure the security of your wireless network. There are three wireless security mode options supported by the Router: WPA Pre-Shared Key, WPA RADIUS, and WEP. (WPA stands for Wi-Fi Protected Access, which is a security standard stronger than WEP encryption.
Wireless-G Broadband Router WEP. WEP is a basic encryption method, which is not as secure as WPA. To use WEP, select a Default Transmit Key (choose which Key to use), and a level of WEP encryption, 64 bits 10 hex digits or 128 bits 26 hex digits. Then either generate a WEP key using a Passphrase or enter the WEP key manually.
Wireless-G Broadband Router The Wireless Tab - Wireless Network Access Wireless access can be filtered by using the MAC addresses of the wireless devices transmitting within your network’s radius. MAC Filter. To filter wireless users by MAC Address, either permitting or blocking access, click Enable. If you do not wish to filter users by MAC Address, select Disable.
Wireless-G Broadband Router The Wireless Tab - Advanced Wireless Settings This tab is used to set up the Router’s advanced wireless functions. These settings should only be adjusted by an expert administrator as incorrect settings can reduce wireless performance. Basic Rate. The Basic Rate setting is not actually one rate of transmission but a series of rates at which the Router can transmit.
Page 32
Wireless-G Broadband Router RTS Threshold. Should you encounter inconsistent data flow, only minor reduction of the default value, 2432, is recommended. If a network packet is smaller than the preset RTS threshold size, the RTS/CTS mechanism will not be enabled. The Router sends Request to Send (RTS) frames to a particular receiving station and negotiates the sending of a data frame.
Wireless-G Broadband Router The Security Tab - Filter Filters block specific internal users from accessing the Internet. From the Filters tab, you can set up a filter through an IP address or a network port number. Filter IP Address Range. To set up a filter using IP addresses, enter the range of IP addresses you wish to filter in the IP address fields.
Wireless-G Broadband Router The Security Tab - VPN Passthrough Use the settings on this tab to allow VPN tunnels in either IPSec or PPTP protocols to pass through the Router’s firewall. IPSec Passthrough. Internet Protocol Security (IPSec) is a suite of protocols used to implement secure exchange of packets at the IP layer.
Wireless-G Broadband Router The Applications and Gaming Tab - Port Range Forwarding The Applications and Gaming Tab allows you to set up public services on your network, such as web servers, ftp servers, e-mail servers, or other specialized Internet applications. (Specialized Internet applications are any applications that use Internet access to perform functions such as videoconferencing or online gaming.
Wireless-G Broadband Router The Applications and Gaming Tab - Port Triggering Port Triggering Port Triggering is used for special applications that can request a port to be opened on demand. For this feature, the Gateway will watch outgoing data for specific port numbers. The Gateway will remember the IP address of the computer that sends a transmission requesting data, so that when the requested data returns through the Gateway, the data is pulled back to the proper computer by way of IP address and port mapping rules.
Wireless-G Broadband Router The Applications and Gaming Tab - DMZ The DMZ feature allows one network user to be exposed to the Internet for use of a special-purpose service such as Internet gaming or videoconferencing. DMZ hosting forwards all the ports at the same time to one PC. The Port Range Forward feature is more secure because it only opens the ports you want to have opened, while DMZ hosting opens all the ports of one computer, exposing the computer to the Internet.
Wireless-G Broadband Router The Administration Tab - Management This section of the Administration tab allows the network’s administrator to manage specific Router functions for access and security. Local Router Access. You can change the Router’s password from here. Enter a new Router password and then type it again in the Re-enter to confirm field to confirm.
Wireless-G Broadband Router The Administration Tab - Log The Router can keep logs of all traffic for your Internet connection. To disable the Log function, keep the default setting, No. To monitor traffic between the network and the Internet, select Yes. Enter the IP Address of the PC where the Logviewer is installed in the Logviewer IP Address field.
Firmware can be upgraded by clicking the Upgrade button after browsing for the firmware, which you can download from the Linksys website, www.linksys.com/international. Do not upgrade your firmware unless you are experiencing problems with the Broadband Router. For more information about upgrading firmware, refer to “Appendix C: Upgrading Firmware”.
Wireless-G Broadband Router The Status Tab - Router The Router screen on the Status Tab displays the Router’s current status. The screen will vary depending on the Internet Connection Type selected on the Setup screen. Firmware Version. This is the Router’s current firmware. Current Time.
Wireless-G Broadband Router The Status Tab - Local Network The Local Network screen on the Status Tab displays the status of your network. MAC Address. This is the Router’s MAC Address, as seen on your local, Ethernet network. IP Address. This shows the Router’s IP Address, as it appears on your local, Ethernet network. Subnet Mask.
Wireless-G Broadband Router The Status Tab - Wireless The Wireless screen on the Status Tab displays the status of your wireless network. MAC Address. This is the Router’s MAC Address, as seen on your local, wireless network. Mode. As selected from the Wireless tab, this will display the wireless mode (Mixed, G-Only, or Disabled) used by the network.
Provided are possible solutions to problems that may occur during the installation and operation of the Router. Read the descriptions below to help you solve your problems. If you can’t find an answer here, check the Linksys website at www.linksys.com.
Page 45
Wireless-G Broadband Router • For Windows 2000: 1. Click Start, Settings, and Control Panel. Double-click Network and Dial-Up Connections. 2. Right-click the Local Area Connection that is associated with the Ethernet adapter you are using, and select the Properties option. 3.
Page 46
Wireless-G Broadband Router • Refer to “Chapter 5: Configuring the PCs” for details. Make sure Obtain IP address automatically is selected in the settings. B Open a command prompt. For Windows 98SE and Me: • Click Start and Run. In the Open field, type command. Press the Enter key or click the OK button. For Windows 2000 and XP: •...
Page 47
Wireless-G Broadband Router 5. I am not able to access the Setup page of the Router’s web-based utility. • Refer to “Problem #3, I want to test my Internet connection” to verify that your computer is properly connected to the Router. •...
Page 48
Wireless-G Broadband Router 7. I need to set up online game hosting or use other Internet applications. If you want to play online games or use Internet applications, most will work without doing any port forwarding or DMZ hosting. There may be cases when you want to host an online game or Internet application.
Page 49
Wireless-G Broadband Router Follow these steps to set DMZ hosting: 1. Access the Router’s web-based utility by going to http://192.168.1.1 or the IP address of the Router. Go to the Applications & Gaming => Port Forwarding tab. 2. Disable or remove the entries you have entered for forwarding. Keep this information in case you want to use it at a later time.
Page 50
Router to the factory default settings. In other words, the Router will revert to its original factory configuration. 12. I need to upgrade the firmware. In order to upgrade the firmware with the latest features, you need to go to the Linksys website and download the latest firmware at www.linksys.com/international. Follow these steps: 1.
Page 51
Wireless-G Broadband Router 15. I can’t access my e-mail, web or I am getting corrupted data from the Internet. The Maximum Transmission Unit (MTU) setting may need to be adjusted. By default, the MTU is set at 1500. For most DSL users, it is strongly recommended to use MTU 1492. •...
Does the Router support any operating system other than Windows 98SE, Windows Millennium, Windows 2000, or Windows XP? Yes, but Linksys does not, at this time, provide technical support for setup, configuration or troubleshooting of any non-Windows operating systems. Does the Router support ICQ send file? Yes, with the following fix: click ICQ menu ->...
Page 53
How will I be notified of new Router firmware upgrades? All Linksys firmware upgrades are posted on the Linksys website at www.linksys.com, where they can be downloaded for free. To upgrade the Router’s firmware, use the System tab of the Router’s web-based utility. If the Router’s Internet connection is working well, there is no need to download a newer firmware version, unless...
Page 54
Wireless-G Broadband Router that version contains new features that you would like to use. Downloading a more current version of Router firmware will not enhance the quality or speed of your Internet connection, and may disrupt your current connection stability. Will the Router function in a Macintosh environment? Yes, but the Router’s setup pages are accessible only through Internet Explorer 4.0 or Netscape Navigator 4.0 or higher for Macintosh.
Page 55
Wireless-G Broadband Router How do I get mIRC to work with the Router? Under the Port Forwarding tab, set port forwarding to 113 for the PC on which you are using mIRC. Can the Router act as my DHCP server? Yes.
Page 56
Wireless-G Broadband Router maintain contact with the wireless network even when not actually transmitting data. Achieving these functions simultaneously requires a dynamic RF networking technology that links access points and nodes. In such a system, the user’s end node undertakes a search for the best possible access to the system. First, it evaluates such factors as signal strength and quality, as well as the message load currently being carried by each access point and the distance of each access point to the wired backbone.
Page 57
There are eleven available channels, ranging from 1 to 11 in North, South, and Central America, and 1 to 13 in most of Europe. If your questions are not addressed here, refer to the Linksys website, www.linksys.com. Appendix A: Troubleshooting...
Wireless-G Broadband Router Appendix B: Wireless Security Linksys wants to make wireless networking as safe and easy for you as possible. The current generation of Linksys products provide several network security features, but they require specific action on your part for implementation.
Page 59
This includes hackers. So, don’t broadcast the SSID. Wireless networking products come with a default SSID set by the factory. (The Linksys default SSID is “linksys”.) Hackers know these defaults and can check these against your network. Change your SSID to something unique and not something related to your company or the networking products you use.
Page 60
These security recommendations should help keep your mind at ease while you are enjoying the most flexible and convenient technology Linksys has to offer. Appendix B: Wireless Security Security Threats Facing Wireless Networks...
The Broadband Router's firmware is upgraded through the Web-based Utility's Administration tab. Follow these instructions: 1. Download the firmware from Linksys's website at www.linksys.com/international. 2. Click the Firmware Upgrade tab on the Web-Utility's Administration tab, and the Upgrade Firmware screen, shown in Figure C-1, will appear.
Wireless-G Broadband Router Appendix D: Windows Help All Linksys wireless products require Microsoft Windows. Windows is the most used operating system in the world and comes with many features that help make networking easier. These features can be accessed through Windows Help and are described in this appendix.
Wireless-G Broadband Router Appendix E: Finding the MAC Address and IP Address for Your Ethernet Adapter This section describes how to find the MAC address for your computer’s Ethernet adapter so you can use the MAC filtering and/or MAC address cloning feature of the Router. You can also find the IP address of your computer’s Ethernet adapter.
Wireless-G Broadband Router 3. Write down the Physical Address as shown on your computer screen (Figure E-3); it is the MAC address for your Ethernet adapter. This appears as a series of numbers and letters. The MAC address/Physical Address is what you will use for MAC address cloning or MAC filtering. Note: The MAC address is also called the Physical Address.
Wireless-G Broadband Router Appendix F: Glossary 802.11a - An IEEE wireless networking standard that specifies a maximum data transfer rate of 54Mbps and an operating frequency of 5GHz. 802.11b - An IEEE wireless networking standard that specifies a maximum data transfer rate of 11Mbps and an operating frequency of 2.4GHz.
Page 66
Wireless-G Broadband Router Buffer - A block of memory that temporarily holds data to be worked on later when a device is currently too busy to accept the data. Cable Modem - A device that connects a computer to the cable television network, which in turn connects to the Internet.
Page 67
Wireless-G Broadband Router Dynamic IP Address - A temporary IP address assigned by a DHCP server. Encryption - Encoding data to prevent it from being read by unauthorized people. Ethernet - An IEEE standard network protocol that specifies how data is placed on and retrieved from a common transmission medium.
Page 68
Passphrase - Used much like a password, a passphrase simplifies the WEP encryption process by automatically generating the WEP encryption keys for Linksys products. Ping (Packet INternet Groper) - An Internet utility used to determine whether a particular IP address is online.
Page 69
Wireless-G Broadband Router PPPoE (Point to Point Protocol over Ethernet) - A type of broadband connection that provides authentication (username and password) in addition to data transport. PPTP (Point-to-Point Tunneling Protocol) - A VPN protocol that allows the Point to Point Protocol (PPP) to be tunneled through an IP network.
Page 70
Wireless-G Broadband Router TCP/IP (Transmission Control Protocol/Internet Protocol) - A network protocol for transmitting data that requires acknowledgement from the recipient of data sent. Telnet - A user command and TCP/IP protocol used for accessing remote PCs. TFTP (Trivial File Transfer Protocol) - A version of the TCP/IP FTP protocol that uses UDP and has no directory or password capability.
Wireless-G Broadband Router Appendix G: Specifications Model WRK54G Standards IEEE 802.3, IEEE 802.3u, IEEE 802.11g, IEEE 802.11b Channels 11 Channels (most of North, South, and Central America) 13 Channels (most of Europe) Ports/Buttons Internet: One 10/100 RJ-45 Port LAN: Four 10/100 RJ-45 Switched Ports One Power Port One Reset Button Cabling Type...
Page 72
Wireless-G Broadband Router Storage Temp. -20ºC to 70ºC (-4ºF to 158ºF) Operating Humidity 10% to 85%, Non-Condensing Storage Humidity 5% to 90%, Non-Condensing Appendix G: Specifications...
Your exclusive remedy and Linksys' entire liability under this warranty will be for Linksys at its option to repair or replace the Product or refund Your purchase price less any rebates.
Wireless-G Broadband Router Appendix I: Regulatory Information FCC Statement This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Page 75
Denna utrustning är i överensstämmelse med de väsentliga kraven och [Swedish]: andra relevanta bestämmelser i Direktiv 1999/5/EC. NOTE: If you need any technical documentation, see the “How to Access Technical Documents on www.linksys.com/international” section for more information. Appendix I: Regulatory Information...
Page 76
Safety: EN 60950 CE Marking For the Linksys Wireless-B and Wireless-G products, the following CE mark, notified body number (where applicable), and class 2 identifier are added to the equipment. Check the CE label on the product to find out which notified body was involved during the assessment.
Page 77
This product is designed for indoor usage only. Outdoor usage is not recommended. This product is designed for use with the included integral or external (dedicated) antenna(s). Use of non-dedicated or third-party antenna(s) is not recommended and is not supported by Linksys. Appendix I: Regulatory Information...
Page 78
Note: The power output setting may not be available on all wireless products. For more information, refer to the documentation on your product’s CD or at http://www.linksys.com/international. Wireless Adapters Wireless adapters have the power output set to 100% by default. Maximum power output on each adapter does not exceed 20 dBm (100 mW);...
Page 79
7. Click the type of documentation you want. The document will automatically open in PDF format. Note: If you have questions regarding the compliance of these products or you cannot find the information you are looking for, please contact your local sales office. Visit http://www.linksys.com/international for more details. Appendix I: Regulatory Information...
Appendix J: Contact Information Need to contact Linksys? Visit us online for information on the latest products and updates to your existing products at: http://www.linksys.com/international If you experience problems with any Linksys product, you can e-mail us at: In Europe E-mail Address Austria support.at@linksys.com...
Page 81
® A Division of Cisco Systems, Inc. Wireless-G 802.11g User Guide Notebook Adapter WIRELESS WPC54G (EU/LA) Model No.
Page 83
Wireless-G Notebook Adapter Table of Contents Chapter 1: Introduction Welcome What’s in this Guide? Chapter 2: Planning your Wireless Network Network Topology Roaming Network Layout Chapter 3: Getting to Know the Wireless-G Notebook Adapter The LED Indicators Chapter 4: Software Installation and Configuration The Installation Procedure Chapter 5: Hardware Installation Connecting the Adapter...
Page 84
Wireless-G Notebook Adapter List of Figures Figure 3-1: Front Panel Figure 4-1: The Setup Wizard’s Welcome screen Figure 4-2: The Setup Wizard’s License Agreement Figure 4-3: The Setup Wizard’s Network Mode screen Figure 4-4: The Setup Wizard’s Wireless Channels screen Figure 4-5: The Setup Wizard’s Finalize Settings screen Figure 4-6: The Setup Wizard’s Congratulations Screen Figure 5-1: How the Adapter installs into your notebook...
And as those hotspots upgrade to the new high-speed Wireless-G standard, you'll be ready to take advantage of the increased speeds. Get connected to current-standard 802.11b networks today, and be prepared for the future with the Wireless-G Notebook Adapter from Linksys. Chapter 1: Introduction Welcome...
Wireless-G Notebook Adapter What’s in this Guide? This user guide covers the steps for setting up and using the Wireless-G Notebook Adapter. • Chapter 1: Introduction This chapter describes the Adapter’s applications and this User Guide. • Chapter 2: Planning Your Wireless Network This chapter discusses a few of the basics about wireless networking.
Page 88
Wireless-G Notebook Adapter • Appendix G: Regulatory Information This appendix supplies the Adapter’s regulatory information. • Appendix H: Contact Information This appendix provides contact information for a variety of Linksys resources, including Technical Support. Chapter 1: Introduction What’s in this Guide?
Linksys wireless adapters also provide users access to a wired network when using an access point or wireless router. An integrated wireless and wired network is called an infrastructure network. Each wireless PC in an infrastructure network can talk to any computer in a wired network infrastructure via the access point or wireless router.
When you wish to connect your wired network with your wireless network, network ports on access points and wireless routers can be connected to any of Linksys's switches or routers. With these, and many other, Linksys products, your networking options are limitless. Go to the Linksys website at www.linksys.com/international for more information about wireless products.
Wireless-G Notebook Adapter Chapter 3: Getting to Know the Wireless-G Notebook Adapter The LED Indicators The Network Adapter's LEDs display information about network activity. Figure 3-1: Front Panel Power Green. The Power LED lights up when the Adapter is powered on. Link Green.
Wireless-G Notebook Adapter Chapter 4: Software Installation and Configuration The Wireless-G Notebook Adapter Setup Wizard will guide you through the installation procedure. The Setup Wizard will install the WLAN Monitor and driver, as well as configure the Adapter. NOTE: You must run the Setup Wizard to install the software before installing the hardware.
In the SSID field, enter the SSID of your wireless network. The SSID must be identical for all devices in the network. The default setting is linksys (all lowercase). Click the Next button. NOTE: Network SSIDs should be unique to your network and identical for all devices within the network.
Page 94
Wireless-G Notebook Adapter 4. If you chose Infrastructure Mode, go to Step 5 now. If you chose Ad-Hoc Mode, select the correct operating channel for your network. Then, select the Network Mode from the drop-down menu. Click the Next button, and go to Step 5. Click the Back button to change any settings. Channel - The channel you choose should match the channel set on the other devices in your wireless network.
Page 95
Wireless-G Notebook Adapter 6. After the software has been successfully installed, the Congratulations screen will appear. Click the Exit button. Proceed to “Chapter 5: Hardware Installation.” Figure 4-6: The Setup Wizard’s Congratulations Screen Chapter 4: Software Installation and Configuration The Installation Procedure...
Wireless-G Notebook Adapter Chapter 5: Hardware Installation NOTE: You must run the Setup Wizard to install the software before installing the hardware. Connecting the Adapter 1. Turn off your notebook PC. 2. Locate an available CardBus slot on your notebook PC. 3.
Wireless-G Notebook Adapter Chapter 6: Using the WLAN Monitor Use the WLAN Monitor to check the link information, search for available wireless networks, or create profiles that hold different configuration settings. Accessing the WLAN Monitor After installing the Adapter, the Wireless-G Notebook Adapter WLAN Monitor icon will appear in your system tray. Double-click the icon.
Page 98
Wireless-G Notebook Adapter State - The status of the wireless network connection. SSID - The SSID of the wireless network. Channel - The channel to which the wireless network devices are set. Security- The status of the security feature. Network Mode - The wireless mode currently in use. IP Address - The IP Address of the Adapter.
Page 99
Wireless-G Notebook Adapter Network Statistics The Networks Statistics screen provides statistics on your current network settings. Transmit Rate - The data transfer rate of the current connection.(In Auto mode, the Adapter dynamically shifts to the fastest data transfer rate possible at any given time.) Receive Rate - The rate that data is received.
Wireless-G Notebook Adapter Site Survey The Site Survey screen displays a list of infrastructure and ad-hoc networks available for connection in the table on the right. This table shows the network’s SSID, Channel, and the quality of the wireless signal the Adapter is receiving.
Wireless-G Notebook Adapter Profiles The Profiles screen lets you save different configuration profiles for different network setups. The table on the right displays a list of infrastructure and ad-hoc networks available for connection This table shows the network’s profile name and the wireless network’s SSID, as set in the connection profile. Profile Information For each profile selected, the following are listed: Network Mode - The mode of the wireless network currently in use.
Wireless-G Notebook Adapter NOTE: If you want to export more than one profile, you have to export them one at a time. Figure 6-8: Exporting a Profile Creating a New Profile 1. On the Profiles screen, click the New button to create a new profile. 2.
Page 103
Wireless-G Notebook Adapter 3. The Choose a network type screen shows a choice of two wireless modes. Click the Infrastructure Mode radio button if you want your wireless computers to communicate with computers on your wired network via a wireless access point. Click the Ad-Hoc Mode radio button if you want multiple wireless computers to communicate directly with each other.
Page 104
WEP key is automatically generated. It is case-sensitive and should not be longer than 16 alphanumeric characters. This passphrase must match the passphrase of your other wireless network devices and is compatible with Linksys wireless products only. (If you have any non-Linksys wireless products, enter the WEP key manually on those products.)
Page 105
Wireless-G Notebook Adapter Transmit Key - The default transmit key number is 1. If your network’s access point or wireless router uses transmit key number 2, 3, or 4, select the appropriate number from the Transmit Key drop-down box. Key 1- The WEP key you enter must match the WEP key of your wireless network. If you are using 64-bit WEP encryption, then the key must consist of exactly 10 hexadecimal characters.
Page 106
Wireless-G Notebook Adapter Select the type of algorithm, TKIP or AES, for the Encryption Type. Enter a WPA Shared Key of 8-63 characters in the Passphrase field. Chapter 6: Using the WLAN Monitor Creating a New Profile Figure 6-17: TKIP Settings...
Page 107
Wireless-G Notebook Adapter WPA RADIUS. WPA RADIUS features WPA used in coordination with a RADIUS server. (This should only be used when a RADIUS server is connected to the Router.) WPA Radius offers two encryption methods, TKIP and AES, with dynamic encryption keys.
Page 108
Wireless-G Notebook Adapter The screen in Figure 6-20 appears next. Select the Authentication Method from the drop-down menu. The options are described below. EAP-TLS Enter the Login name of your wireless network in the Login Name field. From the Certificate drop-down menu, select the certificate you have installed to authenticate you on your wireless network.
Page 109
Wireless-G Notebook Adapter EAP-MD5 Enter the Login name of your wireless network in the Login Name field. Enter the password of your wireless network in the Password field. Click the Next button to continue. Click the Back button to return to the previous screen. EAP-PEAP Enter the Login name of your wireless network in the Login Name field.
Page 110
Wireless-G Notebook Adapter RADIUS RADIUS features WPA used in coordination with a RADIUS server. (This should only be used when a RADIUS server is connected to the Router.) It offers five authentication methods: EAP-TLS, EAP-TTLS, EAP-MD5, EAP- PEAP, and LEAP. Click the Next button to continue and the screen in Figure 6-19 appears.
Page 111
Wireless-G Notebook Adapter EAP-TTLS Enter the Login name of your wireless network in the Login Name field. Enter the password of your wireless network in the Password field. Select Validate server certificate to make sure that the certificate for the server is valid.
Page 112
Wireless-G Notebook Adapter EAP-PEAP Enter the Login name of your wireless network in the Login Name field. Enter the password of your wireless network in the Password field. Select Validate server certificate to make sure that the certificate for the server is valid.
Page 113
Wireless-G Notebook Adapter 7. The Confirm New Settings screen will appear next showing the new settings. To save the new settings, click the Yes button. To edit the new settings, click the Back button. 8. The Congratulations screen will appear next. Click Activate new settings now to implement the new settings immediately and return to the Link Information screen.
Wireless-G Notebook Adapter. Read the description below to solve your problems. If you can't find an answer here, check the Linksys website at www.linksys.com/international. Common Problems and Solutions 1.
Wireless-G Notebook Adapter Frequently Asked Questions Can I run an application from a remote computer over the wireless network? This will depend on whether or not the application is designed to be used over a network. Consult the application’s user guide to determine if it supports operation over a network. Can I play computer games with other members of the wireless network? Yes, as long as the game supports multiple players over a LAN (local area network).
Page 116
Wireless-G Notebook Adapter What is ad-hoc mode? When a wireless network is set to ad-hoc mode, the wireless-equipped computers are configured to communicate directly with each other. The ad-hoc wireless network will not communicate with any wired network. What is infrastructure mode? When a wireless network is set to infrastructure mode, the wireless network is configured to communicate with a wired network through a wireless access point.
Page 117
Wireless-G Notebook Adapter the receiver knows the parameters of the spread-spectrum signal being broadcast. If a receiver is not tuned to the right frequency, a spread-spectrum signal looks like background noise. There are two main alternatives, Direct Sequence Spread Spectrum (DSSS) and Frequency Hopping Spread Spectrum (FHSS). What is DSSS? What is FHSS? And what are their differences? Frequency-Hopping Spread-Spectrum (FHSS) uses a narrowband carrier that changes frequency in a pattern that is known to both transmitter and receiver.
Wireless-G Notebook Adapter Appendix B: Wireless Security Linksys wants to make wireless networking as safe and easy for you as possible. The current generation of Linksys products provide several network security features, but they require specific action on your part for implementation.
Page 119
This includes hackers. So, don’t broadcast the SSID. Wireless networking products come with a default SSID set by the factory. (The Linksys default SSID is “linksys”.) Hackers know these defaults and can check these against your network. Change your SSID to something unique and not something related to your company or the networking products you use.
Page 120
These security recommendations should help keep your mind at ease while you are enjoying the most flexible and convenient technology Linksys has to offer. Appendix B: Wireless Security Security Threats Facing Wireless Networks...
Wireless-G Notebook Adapter Appendix C: Windows Help All wireless products require Microsoft Windows. Windows is the most used operating system in the world and comes with many features that help make networking easier. These features can be accessed through Windows Help and are described in this appendix.
Wireless-G Notebook Adapter Appendix D: Glossary 802.11b - A wireless networking standard that specifies a maximum data transfer rate of 11Mbps and an operating frequency of 2.4GHz. 802.11g - A wireless networking standard that specifies a maximum data transfer rate of 54Mbps, an operating frequency of 2.4GHz, and backward compatibility with 802.11b devices.
Page 123
Wireless-G Notebook Adapter Cable Modem - A device that connects a computer to the cable television network, which in turn connects to the Internet. CSMA/CA (Carrier Sense Multiple Access/Collision Avoidance) - A method of data transfer that is used to prevent data collisions.
Page 124
Wireless-G Notebook Adapter EAP (Extensible Authentication Protocol) - A general authentication protocol used to control network access. Many specific authentication methods work within this framework. EAP-PEAP (Extensible Authentication Protocol-Protected Extensible Authentication Protocol) - A mutual authentication method that uses a combination of digital certificates and another system, such as passwords. EAP-TLS (Extensible Authentication Protocol-Transport Layer Security) - A mutual authentication method that uses digital certificates.
Page 125
Passphrase - Used much like a password, a passphrase simplifies the WEP encryption process by automatically generating the WEP encryption keys for Linksys products. Ping (Packet INternet Groper) - An Internet utility used to determine whether a particular IP address is online.
Page 126
Wireless-G Notebook Adapter POP3 (Post Office Protocol 3) - A standard mail server commonly used on the Internet. Port - The connection point on a computer or networking device used for plugging in cables or adapters. Power over Ethernet (PoE) - A technology enabling an Ethernet network cable to deliver both data and power. PPPoE (Point to Point Protocol over Ethernet) - A type of broadband connection that provides authentication (username and password) in addition to data transport.
Page 127
Wireless-G Notebook Adapter SSID (Service Set IDentifier) - Your wireless network's name. Static IP Address - A fixed address assigned to a computer or device that is connected to a network. Static Routing - Forwarding data in a network via a fixed path. Subnet Mask - An address code that determines the size of the network.
Page 128
Wireless-G Notebook Adapter WAN (Wide Area Network)- The Internet. WEP (Wired Equivalent Privacy) - A method of encrypting network data transmitted on a wireless network for greater security. WINIPCFG - A Windows 98 and Me utility that displays the IP address for a particular networking device. WLAN (Wireless Local Area Network) - A group of computers and associated devices that communicate with each other wirelessly.
Your exclusive remedy and Linksys' entire liability under this warranty will be for Linksys at its option to repair or replace the Product or refund Your purchase price less any rebates.
Wireless-G Notebook Adapter Appendix G: Regulatory Information FCC Statement This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Page 132
Denna utrustning är i överensstämmelse med de väsentliga kraven och [Swedish]: andra relevanta bestämmelser i Direktiv 1999/5/EC. NOTE: If you need any technical documentation, see the “How to Access Technical Documents on www.linksys.com/international” section for more information. Appendix G: Regulatory Information...
Page 133
Safety: EN 60950 CE Marking For the Linksys Wireless-B and Wireless-G products, the following CE mark, notified body number (where applicable), and class 2 identifier are added to the equipment. Check the CE label on the product to find out which notified body was involved during the assessment.
Page 134
This product is designed for indoor usage only. Outdoor usage is not recommended. This product is designed for use with the included integral or external (dedicated) antenna(s). Use of non- dedicated or third-party antenna(s) is not recommended and is not supported by Linksys. Appendix G: Regulatory Information...
Page 135
Note: The power output setting may not be available on all wireless products. For more information, refer to the documentation on your product’s CD or at http://www.linksys.com/international. Wireless Adapters Wireless adapters have the power output set to 100% by default. Maximum power output on each adapter does not exceed 20 dBm (100 mW);...
Page 136
7. Click the type of documentation you want. The document will automatically open in PDF format. Note: If you have questions regarding the compliance of these products or you cannot find the information you are looking for, please contact your local sales office. Visit http://www.linksys.com/international for more details. Appendix G: Regulatory Information...
Appendix H: Contact Information Need to contact Linksys? Visit us online for information on the latest products and updates to your existing products at: http://www.linksys.com/international If you experience problems with any Linksys product, you can e-mail us at: In Europe E-mail Address Austria support.at@linksys.com...