Page 1 Hand-Held Computer Microsoft® Windows® Mobile 6.5 Operating System Reference Guide...
Page 2: Limited Warranty
Disclaimer Honeywell International Inc. (“HII”) reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult HII to determine whether any such changes have been made. The information in this publication does not represent a commitment on the part of HII.
Page 3: Table Of Contents
Back Trigger Handle Handstrap Label Locations External Power Supplies AC/DC 15V Power Supply Car Power Adapter 1-10 Replace CLA Fuse 1-10 Locking the MX9 1-10 Reboot 1-11 Warmboot 1-11 Restart (or Cold Boot) 1-11 Startup Help 1-11 Chapter 2 - Hardware System Hardware 802.11 b/g and a/b/g Wireless Client...
Page 4 Status LEDs System Status LED Battery Charging Status LED Alpha mode Status LED Bluetooth Status LED Scanner Status LED Cold Storage Vibrate Indicator Scanners and Imagers Integrated Bar Code Decoders Tethered Bar Code Decoders Bluetooth Client Bar Code Decoders GPS Module Chapter 3 - Power Power Modes On Mode...
Page 5 RFTerm (Option) 4-13 Status Popup 4-13 HSMConnect 4-14 GrabTime 4-14 Synchronize with a local time server 4-14 Enhanced Launch 4-14 MX9 OS Upgrade 4-15 Introduction 4-15 OS and Language Options 4-15 Preparation 4-15 Accessing the SD Card Slot 4-16 Procedure 4-17...
Page 6 MAC Address 4-22 Clock & Alarms 4-23 Time 4-23 Alarms 4-24 More 4-25 Lock 4-26 Password 4-26 Hint 4-27 Display 4-28 Power 4-29 Battery 4-29 Advanced 4-30 Sounds & Notifications 4-31 Sounds 4-32 Notifications 4-33 Vibrations 4-34 Today 4-35 Personal Panels 4-37 Buttons 4-37...
Page 7 Using a Stylus Tap 4-52 Using the Switch Key Sequence 4-52 Hotkey (Activation hotkey) 4-52 Application Configuration 4-53 Application Panel 4-54 Launch Button 4-56 Auto At Boot 4-57 Auto Re-Launch 4-58 Manual (Launch) 4-59 Match 4-59 Allow close 4-59 End User Internet Explorer (EUIE) 4-60 Security Panel 4-61...
Page 8 About 4-87 Easy Pairing and Auto-Reconnect 4-87 Bluetooth Indicators 4-88 Bluetooth Bar Code Reader Setup 4-89 Introduction 4-89 MX9 with Label 4-90 MX9 without Label 4-91 Bluetooth Reader Beep and LED Indications 4-92 Bluetooth Printer Setup 4-92 Certificates 4-93 Personal...
Page 9 Wi-Fi 4-119 4-119 Initial Setup 4-120 Connection 4-121 Network 4-122 TCP/IP 4-123 Autoconnect 4-124 Admin 4-125 About 4-126 Connections Panel 4-127 Beam 4-127 Connections 4-128 Domain Enroll 4-130 Network Cards 4-131 Wireless Manager 4-133 Miscellaneous Start Panels 4-135 Standard Microsoft Applications 4-135 Internet Explorer Mobile 4-142...
Page 10 Configuring the MX9 with HSMConnect Install HSMConnect Using HSMConnect Chapter 6 - Data Collection Return to Factory Default Settings Data Processing Overview Main Tab Continuous Scan Mode COM1 Tab Notification Tab Data Options Tab Enable Code ID Buttons 6-10 Symbology Settings...
Page 11 Chapter 7 - Enhanced Launch Utility Introduction Registry Based Launch Items Launch Startup options Example Script Based Launch Items Enhanced Launch Utility Use File Names Command line structure Comments Commands Supported by Launch Launch Error Messages 7-19 Example Script File 7-21 Chapter 8 - Enabler Installation and Configuration Introduction...
Page 12 Exit 8-22 Using Remote Management 8-23 Using eXpress Scan 8-24 Step 1: Create Bar Codes 8-24 Step 2: Scan Bar Codes 8-24 Step 3: Process Completion 8-25 Chapter 9 - Wireless Network Configuration Introduction Important Notes Summit Client Utility Help Summit Tray Icon Using Windows Mobile Wireless Manager Create a New Network Connection...
Page 13 Exporting a User Certificate 9-55 Installing a User Certificate 9-56 Chapter 10 - Keymaps 10-1 MX9 62-Key Keymap 10-1 MX9 62-Key 5250 Keypad Keymap 10-6 MX9 38-key Keymap 10-12 Chapter 11 - Technical Specifications 11-1 Dimensions and Weight 11-2 Environmental Specifications...
Page 15: Chapter 1 - Introduction
The keypad is available in a 62-key or 38-key configuration. The 62-key keypad is also available in an IBM 5250 configuration. Bar code reader options are: an imager or laser scanner integrated in the MX9, or a handheld scanner tethered to the port at the base of the MX9, Bluetooth mobile bar code imagers and scanners, or the Honeywell Bluetooth ring scanner / ring imager.
Page 16: Components
Components Front 1. Microphone 2. Touch screen 3. Speaker 4. Scan buttons 5. Enter key 6. Scanner status LED 7. Power key Note: The above list is the same on the 38 key MX9. Special keys are listed below.
Page 17: Special Purpose Keys
Special Purpose Keys 1. Function Keys 2. Cursor up and down Keys 3. Diamond 1 key 4. Backspace [BS] key and Space [SPC] 5. Escape [ESC] key 6. Power key 7. Tab key 8. Alt key 9. Control [CTL] key 10.
Page 18: Special Purpose Keys - 38 Key
Special Purpose Keys - 38 Key 1. Diamond 1 key 2. Function keys 3. Tab / Space / Backspace keys 4. Diamond 2 key 5. Orange key 6. Escape [ESC] key 7. Alpha key 8. Control [CTRL] key 9. Shift [SHIFT] key 10.
Page 19: Top
Bar code reader aperture Bottom Input / Output Connector Tethered boot cover not shown (covers I/O connector) Back Battery Bay 1. Battery Terminals 2. Battery Bay 3. Battery Bay Access Tab...
Page 20: Trigger Handle
Trigger Handle Trigger handle attach points 1. Upper 2. Lower 1. Trigger 2. Tether attach point Stylus storage bay in handle...
Page 21: Handstrap
Handstrap 1. Handstrap 2. Handstrap Base 3. Stylus 1. Attach - Upper Handstrap Base 2. Attach - Lower Handstrap Base 1. Handstrap connector, upper 2. Stylus holder on Handstrap 3. Handstrap connector, lower...
Page 22: Label Locations
Label Locations 1. Laser Warning Label 2. Bluetooth Label 3. Product Identification Label 4. Java Label (if installed) 5. Windows OS License Label 6. Tamper Proof Label The tamper-proof label covers the top right screw in the battery bay. The label states "Warranty void if removed or damaged". The battery pack will not deface the label as the battery pack does not touch the label.
Page 23: External Power Supplies
The MX9 and desk cradle and multi-charger use the same external power supply. AC/DC 15V Power Supply The MX9 receives AC/DC power from the AC/DC (15 VDC - 4 Amp - 60 Watt) Power Supply. The MX9 external power connection is part of the serial cable assembly and the USB cable assembly.
Page 24: Car Power Adapter
Car Power Adapter The MX9 Car Power Adapter is a self-contained unit. The cable has one and a half feet of coiled cord and one and a half feet of straight cord. The coiled portion is on the end of the adapter. An LED on the adapter illuminates when the car power adapter is receiving vehicle input power.
Page 25: Reboot
When the Windows Mobile Today panel is displayed or an application begins, the power up (or reboot) sequence is complete. Warmboot A warmboot reboots the MX9 without erasing any registry data. Applications and data in RAM are preserved during a warmboot.
Page 26 1-12...
Page 27: Chapter 2 - Hardware
802.11 b/g and a/b/g Wireless Client The MX9 has an 802.11x network card that supports diversity with two internal antennas. The CPU board does not allow hot swapping the network card. Power management on the network card is set to static dynamic control.
Page 28: Video Subsystem
Ethernet (only accessible when MX9 is secured in a cradle's docking bay) The MX9 cables are designed to be securely connected to this port. This port is also used to connect the MX9 to the docking bay connector in cradles.
Page 29: Bluetooth
Power input Ethernet (accessible when MX9 is secured in a powered cradle's docking bay) The MX9 cables are designed to be securely connected to this port. This port is used to connect the MX9 to the docking bay connector in cradles.
Page 30: Keypads
Keypads The MX9 keypad is either a 62-key full alphanumeric keypad or 38-key numeric-alpha. The 62 key keypad has an ANSI or a 5250 overlay. Keymaps are available for all keypads. Note: The keypad backlight default setting is to follow the display backlight setting until it is changed by the user.
Page 31: Expansion Slots
SIMM card SD card The expansion slots in the MX9 are accessible via the hatch. The hatch can be opened using a standard size screwdriver. When the hatch is opened, the MX9 automatically shuts down. SD card configurations in 512MB, 1GB and 4GB are available from Honeywell.
Page 32: Status Leds
Status LEDs Several LEDs are located on the front of the MX9 above the integrated speaker. They are: System Status (SYS) LED indicates power management status. Battery Charging Status (BATT) LED indicates main battery charging status. Alpha Mode Status (ALPHA) LED applies to the 38-key keypad only.
Page 33: Scanner Status Led
MX9. The Scan LED on the wireless Bluetooth mobile scanner/imager illuminates. Note: A scanned bar code can be accepted as a good scan or a bad scan by the MX9 bar code decoder (as configured). The appropriate audible or tactile indicator is activated.
Page 34: Vibrate Indicator
A scan aperture heater is implemented for low temperature environments. Tethered Bar Code Decoders The external serial port at the base of the MX9 is used to connect (via serial tether) tethered laser scanners as needed. Bluetooth Client Bar Code Decoders The Bluetooth Module in the MX9 can accept data from paired Bluetooth bar code readers.
Page 35: Chapter 3 - Power
Off mode to the On mode when a charged main battery is inserted or external power is applied and the Power key is pressed. Suspend Mode The Suspend mode is entered when the unit is inactive for a predetermined period of time or the user taps the Power key. MX9 Suspend timers are set using Start >...
Page 36: Batteries
An extra Li-Ion battery pack can be recharged in a powered desktop cradle. The battery is fully recharged in a powered cradle in less than 4 hours. The MX9 can be Off, in use or in Suspend Mode while the battery is recharging.
Page 37: Battery Hotswapping
The MX9 has an internal battery that is designed to provide limited-duration electrical power in the event of main battery failure. The energy needed to maintain the internal battery near full charge at all times is drawn from the MX9 main battery. It takes 5 minutes or less to fully charge the internal battery.
Page 39: Chapter 4 - Software
The files are stored in folders in the mobile device. This section lists the contents of the folders and the general function of the files. Files installed in each MX9 are specific to the intended function of the MX9.
Page 40: Software Load
The MX9 has a unique 128-bit ID code as required by the Windows Mobile specification. This ID number is generated by the boot loader. This ID code is available in the About Info settings panel, and via a Win32 standard API.
Page 41: Boot Loader
CAB files available for the MX9. Software Development The CE API Programming Guide documents API calls for the MX9. It is intended as an addition to the standard Microsoft Windows Mobile API documentation.
Page 42: Today Screen
The main screen for the MX9 is known as the Today screen. The Today screen shows various options and status icons. The Today screen appearance is configurable by selecting Start > Settings > Today. Both the appearance of the Today screen and the items displayed may be configured.
Page 43: Configurable Today Screen Listing
When the MX9 is unlocked, tapping on Device unlocked locks the MX9. When the MX9 is locked, tapping on Unlock at the bottom of the screen unlocks the MX9. Depending on the settings, a password may be required. The MX9 can also be configured to lock after a period of inactivity. For more information, please...
Page 44: Notification Bar
Vibrate is on. Power The MX9 is connected to external power. The MX9 is operating on battery power. The strength of the battery is indicated by the number of bars dis- Power played: 0 (low battery) to 4 (fully charged battery).
Page 45: Status Icons
MX9 is not connected to any Bluetooth device. MX9 is ready to connect with any Bluetooth device. MX9 is out of range of all paired Bluetooth device(s). Connection is inactive. Summit radio is not currently associated or authenticated to an Access Point.
Page 46: Start Menu Options
Can be synchronized with PC Outlook email using ActiveSync or it can synchronize with an Exchange server. File Explorer. Displays a structured picture of files on the system. Help. Access Windows Mobile help system on the MX9. Options to search using Windows Live Search are available. Internet Explorer. Access web pages on the Internet.
Page 47 Tasks. Task list application. Can be synchronized with PC Outlook task list using ActiveSync. Today. Configure the appearance and the items to display on the Today screen. Windows Live. Sign in to Microsoft Windows Live online service. Internet access required. Windows Media. Audio visual management program. Not supported on the MX9.
Page 48: Office Mobile
Office Mobile Icon Function Excel Mobile. Spreadsheets can be edited, data can be sorted, formatting and changes are preserved. PowerPoint Mobile. Open, view and edit slides in landscape or portrait format. Zoom and GoTo features enabled. Word Mobile. Open, view, edit documents. Formats are saved. Spelling checker, cut and paste are available, undo and redo commands.
Page 49: Installed Programs
Tools > Options to set up the default home page, view browsing history, setup privacy and security, preferred language, and Other options. If an Internet Explorer web page is larger than the MX9 screen can display at one time, use touch screen gestures for horizontal and vertical scrolling.
Page 50: Summit
Only installed on a Bluetooth equipped MX9. The System Administrator can Discover and Pair targeted Bluetooth devices for each MX9. The System Administrator can enable / disable Bluetooth settings and assign a Computer Friendly Name for each MX9. Bluetooth can be accessed by tapping Start >...
Page 51: Rfterm (Option)
Information to include in Admin or User Status Popup. The Status Popup can be dismissed by the expiration of the timeout (if enabled), tapping the status window or pressing the key assigned to the popup. For more information, please refer to the Buttons and MX9 Options settings. 4-13...
Page 52: Hsmconnect
PC. Any keystrokes on the host PC are passed to the MX9 as if they were keystrokes on the MX9 keypad. HSMConnect for the MX9 is available on the Getting Started Disc. GrabTime GrabTime is a utility to synchronize the MX9 with a world-wide time server. GrabTime can be started as a service by setting it in the Launch option (see the following section for details on Launch).
Page 53: Mx9 Os Upgrade
OS and Language Options The MX9 running Windows Mobile must be returned to the manufacturer, Honeywell, if the device is to be re-imaged with any other Windows operating system (for example, Windows CE).
Page 54: Accessing The Sd Card Slot
The expansion slots in the MX9 are accessible via the hatch. The hatch can be opened using a standard size screwdriver. When the hatch is opened, the MX9 automatically shuts down. It is good practice to save any changes then perform an orderly shutdown to preserve RAM contents before opening the hatch.
Page 55: Procedure
Procedure While the hatch is open slide the installed SD card out of the slot. The MX9 may not have a SD card in the slot because the OS is in flash. 1. Place the card with the new image files on it into the SD slot. The label on the SD card should be facing up.
Page 56: Settings
Notifications. Enable / disable sounds and vibrations. Set volume parameters and assign sound (wav) files to OS events. Today. Configure the Today screen. Connections. Set up various connections between a host and the MX9. Personal. Configure Buttons, Input method and Owner information. System. Review system information. Set up operating system and equipment parameters.
Page 57: Personal
Personal Start > Settings > Personal Icon Option Buttons. Set functions of programmable buttons. Input. Set input options for keypad, touch screen and voice. Owner Information. Set the mobile device owner details (name, phone, etc). Enter notes. Enable / disable Owner display parameters.
Page 58 Icon Option External GPS. Configure serial GPS access. License Manager. View license information for installed licensed applications. Managed Programs. View install history for .NET programs. Memory. Display current state of virtual memory. Mixer. Adjust the input and output parameters – volume, side-tone, and record gain, for headphone, software and microphone.
Page 59: Connections
Connections Start > Settings > Connections Icon Option Beam. Enable receiving InfraRed and Bluetooth beams. (Not supported on the MX9.) Connections. Configure connections to servers. Domain Enroll. Enroll in Active Directory domain. Network Cards. Set the parameters for a wireless network using the utility included in Windows Mobile.
Page 60: Settings Panels
The Versions tab displays the versions of many of the software programs installed. Not all installed software on the mobile device is included in this list and the list varies depending on the applications loaded on the MX9. The Image line displays the revision of the system software installed.
Page 61: Clock & Alarms
Clock & Alarms Start > Settings > Clock & Alarms Time Adjust the settings and tap ok to save the changes. Select Yes on the popup box and the changes take effect immediately. The Time can be set for both a Home and a Visiting location. 4-23...
Page 62: Alarms
Alarms To set an alarm: 1. Tap the checkbox to enable the alarm. 2. Tap < Description > and enter a description. The description is limited to 63 characters. 3. Tap the day (or days) to play the alarm. 4. Tap the time to set the time to play the alarm. Set the time and tap ok to return to the Alarms panel. 5.
Page 63: More
More Note: Tap Start > Help for context sensitive Windows Mobile Help when changing or viewing options. Tap the X icon in the top right corner to close Windows Mobile Help. 4-25...
Page 64: Lock
<blank> Prompt if phone unused for – Check the checkbox and set the inactivity timeout before the MX9 locks. When selecting a Password type the screen displays a numeric keypad or the input panel depending on the type of password selected.
Page 65: Hint
Hint If the password entry isn’t successful after a predefined number of attempts, the password hint is displayed. Factory Default Settings Password hint <blank> 4-27...
Page 66: Display
Display Unlock display defaults to Windows Classic. Windows Default can be selected to be the unlock display. Changing the unlock display, and tapping OK (at the top right corner of the screen) presents the following screen: Tap Yes to restart, or cold boot. Tap No to cancel the operation. Note: Tap Start >...
Page 67: Power
Power Start > Settings > System > Power Reports the current battery state and allows the user to set suspend timeouts. Battery Battery power is displayed for both the main and internal Super-cap batteries. 4-29...
Page 68: Advanced
Turn off device if not used for Enabled Timer setting 5 minutes Select the inactivity timeout period before the MX9 goes into suspend. The settings on this panel are for the suspend timers only. Backlight timers are set using the Backlight settings panel.
Page 69: Sounds & Notifications
Sounds & Notifications Start > Settings > Personal > Sounds & Notifications Set volume parameters and assign sound WAV files to Windows Mobile events. Options that cannot be edited by the user are dimmed. Factory Default Settings Sounds Events Enabled Programs Enabled Notifications...
Page 70: Sounds
Sounds Follow the instructions on the screen and tap ok to save the changes. Changes take effect immediately. 4-32...
Page 71: Notifications
Notifications The Event box lists several events that can have an associated notification. The notification, depending on the event selected, may consist of playing a sound, displaying a screen message, flashing a light or triggering the vibration motor. When finished, tap ok to save the changes. 4-33...
Page 72: Vibrations
Vibrations Vibration on Screen taps is disabled by default. Check the checkbox to enable vibration on screen taps. Short vibration is enabled by default. When finished, tap ok to save the changes. Changes take effect immediately. Note: Tap Start > Help for context sensitive Windows Mobile Help when changing or viewing options. Tap the X icon in the top right corner to close Windows Mobile Help.
Page 73: Today
The Today timeout timer refers to the "return to Today screen" function. When the device is placed in Suspend, and the timer expires, a return from Suspend displays the Today screen, not the application in focus when the MX9 was placed in Suspend.
Page 74 Use Options to set display parameters for highlighted items in the Checked Items list. Note: Tap Start > Help for context sensitive Windows Mobile Help when changing or viewing options. Tap the X icon in the top right corner to close Windows Mobile Help. 4-36...
Page 75: Personal Panels
Personal Panels Buttons Start > Settings > Personal > Buttons Program Buttons Program buttons can be used to assign functions to certain keys such as F1 through F5 and the diamond keys. Buttons can only be assigned to programs that have an icon in the Start menu or the Settings folder (including sub-folders). A program that is not in the above mentioned locations does not show up in the list here.
Page 76 To assign a button: 1. Tap to highlight the desired button. 2. Select the program or shortcut from the Assign a program pulldown box. 3. Tap ok. 4-38...
Page 77: Up/Down Control
Up/Down Control Customize the delay before repeating and the repeat rate for the up/down controls. Note: Tap Start > Help for context sensitive Windows Mobile Help when changing or viewing options. Tap the X icon in the top right corner to close Windows Mobile Help. 4-39...
Page 78: Input
Input Start > Settings > Personal > Input Input Method Select the preferred method of input. Factory Default Settings Input Method Keyboard Small keys Enabled The default method of input is the keyboard or input panel. When the cursor is located in a field allowing text input, the input panel may automatically be displayed.
Page 79: Word Completion
Word Completion Factory Default Settings Suggest words when entering text Enabled Suggest after entering A space Suggest _ word(s) Add a space after word Enabled Enable auto correct Enabled 4-41...
Page 80: Options
Options Factory Default Settings Voice recording format 8000 Hz, 8 Bit, Mono Default zoom level for writing 200% Default zoom level for typing 100% Capitalize first letter of sentence Enabled Scroll upon reaching the last line Enabled Note: Tap Start > Help for context sensitive Windows Mobile Help when changing or viewing options. Tap the X icon in the top right corner to close Windows Mobile Help.
Page 81: Owner Information
Owner Information Start > Settings > Personal > Owner Information Set the MX9 owner details. Factory Default Settings Identification Name, Company, Address, Telephone, E-mail Blank Notes Notes Blank Enter the information and tap ok to save the changes. The changes take effect immediately.
Page 82: System Panels
System Panels About Start > Settings > System > About The About panels show OS versions, allow device name and description input and display copyright information. The following screens are examples only. Version This screen displays information on the installed operating system and the hardware. Note that Windows Mobile is based on a Windows CE engine.
Page 83: Device Id
Device ID Factory Default Settings Device Name [device_specific]001 Device Description WM_MX9 The device name and description can be changed. Enter the name and description using either the keypad or the Input Panel and tap ok to save the changes. The changes take effect immediately. Note: Changing the device name deletes previous ActiveSync settings including backed up user files.
Page 84: Copyrights
Copyrights This screen is presented for information only. The Copyrights information cannot be changed by the user. 4-46...
Page 85: Administration - For Applock
AppLock is designed to be run on Windows based devices only. The AppLock program is installed before shipping. MX9 AppLock is setup by the Administrator by tapping Start > Settings > System > Administration. Configuration parameters are specified by the AppLock Administrator for the MX9 end-user. AppLock is password protected by the Administrator.
Page 86: Factory Default Settings - Applock
Factory Default Settings - AppLock Application Panel Filename Blank Title Blank Arguments Blank Order Internet Disabled Global Key Ctl+Spc / Ctrl+Spc Global Delay 10 sec Input Panel Disabled Launch Button Panel Auto at Boot Enabled Auto at Boot Retries Auto at Boot Delay 10 sec Auto Re-launch Enabled...
Page 87: Setup A New Device
MX9 and no password prompt is displayed. After the administrator specifies applications to lock, a password is assigned and the device is rebooted or the hotkey is pressed, the MX9 switches to end-user mode.
Page 88: Administration Mode
Administration Mode Administration mode gives full access to the mobile device, hardware and software configuration options. The administrator must enter a valid password (when a password has already been assigned) before access to Administration mode and configuration options are allowed. The administrator can configure the following options: Create/change the keystroke sequence to activate administrator access.
Page 89: Passwords
Passwords A password must be configured. If the password is not configured, a new device switches into Administration mode without prompting for a password. In addition to the Administrator hotkey press, a mode switch occurs if inaccurate information has been configured or if mandatory information is missing in the configuration. There are several situations that display a password prompt after a password has been configured.
Page 90: End-User Switching Technique
End-User Switching Technique A checkmark in the switchpad menu (see image above) indicates applications currently active or available for Launching by the user. When Keyboard is selected, the MX9 default input method (Input Panel, Transcriber, or custom input method) is activated.
Page 91: Application Configuration
Application Configuration Settings > System > Administration icon The default Administrator Hotkey sequence is Shift+Ctrl+A. Administrator mode allows access to all features on the device. When the hotkey is pressed to switch into Administrator mode, a password prompt is displayed (if a password has been configured). A password must be entered within 30 seconds (and within three tries) or the password prompt is removed and the device remains in end-user mode with the focus returned to the locked application.
Page 92: Application Panel
Use the Application tab options to select the applications to launch when the device boots up in End-user Mode. If no application is specified when the Administrator Panel is closed, the MX9 reboots into Administrator mode. If a password has been set, but an application has not been specified, the user will be prompted for the password before entering administration mode.
Page 93 Option Explanation Default is 10 seconds. Enter the number of seconds that Applications must wait before starting to run after reboot. Global Delay Note: Delay (Global) may not be available in all versions of AppLock. You can simulate a Global Delay function by setting a delay for the first application (lowest Order) launched and setting the delay to 0 for all other applications.
Page 94: Launch Button
Launch Button When clicked, displays the Launch options panel for the Filename selected on the Administration panel. Note: Launch order is determined by the Order specified in the Application tab. The Order value does not have to be sequential. 4-56...
Page 95: Auto At Boot
Auto At Boot Default is Enabled. Auto At Boot When enabled, automatically launches (subject to the specified Delay in seconds) the application after the unit is rebooted. If a Delay in seconds is specified, AppLock waits for the specified period of time to expire before launching the application. The Delay default value is 10 seconds;...
Page 96: Auto Re-Launch
Auto Re-Launch Default is Enabled. When enabled for a specific application. automatically re-launches it (subject to the specified Auto Re-Launch Delay in seconds) after it terminates. This option allows the Administrator to disable the re-launch operation. AppLock cannot prevent all applications from closing.
Page 97: Manual (Launch)
Manual (Launch) Default is Disabled. Enabling this option allows the end-user to launch the specified application(s). Upon bootup completion an application with Manual enabled is listed on the Switchpad accompanied by a checkmark that indicates the application is currently active or available for Launching. When an application name is tapped by the end-user, the application is launched (if inactive) and brought to the foreground.
Page 98: End User Internet Explorer (Euie)
End User Internet Explorer (EUIE) AppLock supports applications that utilize Internet Explorer, such as .HTML pages and JAVA applications. The end user can run an application by entering the application name and path in Internet Explorer’s address bar. To prevent the end user from executing an application using this method, the address bar and Options settings dialog are restricted in Internet Explorer.
Page 99: Security Panel
Security Panel Setting an Activation Hotkey Specify the hotkey sequence that triggers AppLock to switch between administrator and user modes and the password required to enter Administrator mode. The default hotkey sequence is Shift+Ctrl+A. key keypress is an invalid keypress for a hotkey sequence. Move the cursor to the Hot Key text box.
Page 100: Setting A Password In The Security Panel
Setting a Password in the Security Panel Move the cursor to the Password text box. The passwords entered in the Password and Confirm Password fields must match. Passwords are case sensitive. When the user exits the Administrator panel, the two passwords are compared to verify that they match. If they do not match, a dialog box is displayed notifying the user of the error.
Page 101: Options Panel
Options Panel AppLock uses 3 timeout values when locking applications: Launch timeout -- the time to wait for an application to initially launch before timing out. Default value is 60000 milliseconds (60 seconds). Replace timeout -- the time to wait for an application to replace the current window with another one before timing out. Default value is 20000 milliseconds (20 seconds).
Page 102: Status Panel
Status Panel Use the Status panel to view the log of previous AppLock operations and to configure which messages are to be recorded during AppLock operation. Status information is stored in a specific location on the storage device and in a specific logfile specified by the Administrator. For this reason, the administrator can configure the type of status information that is logged, as well as clear the status information.
Page 103: Log
Note: If a level higher than Error is selected, the status should be cleared frequently by the administrator. In addition to the three view levels the administrator can select that all status information be logged or turn off all status information logging completely.
Page 104: Applock Help
When the Administrator is selecting a hotkey sequence to use when switching user modes, they are not allowed to enter key combinations that are reserved by installed software applications. Honeywell has validated RFTerm key combinations ONLY. When RFTerm is installed on the mobile device and an RFTerm restricted key sequence is specified as a hotkey sequence by the Administrator, the following error message is displayed in a message box: Selected hotkey is not allowed.
Page 105: Applock Error Messages
AppLock Error Messages Any messages whose first word is an ‘ing’ word is output prior to the action described in the message. For example, “Switching to admin-hotkey press” is logged after the administrator has pressed the hotkey but prior to starting the switch process. For all operations that can result in an error, an Error level message is displayed when a failure occurs.
Page 106 Message Explanation and/or corrective action Level Could not create event The keyboard filter uses this event at the Administrator Control panel. The event could not be created. LOG_ERROR EVT_HOTKEYCHG If the keyboard cannot be controlled, AppLock cannot process the hotkey. This failure prevents a mode switch Could not hook keyboard LOG_ERROR into user mode.
Page 107 Message Explanation and/or corrective action Level Encrypt length failure Unable to encrypt password. LOG_ERROR Encrypt out of memory for Unable to encrypt password. LOG_ERROR Encrypted data OK The password has been successfully encrypted. LOG_EX In order for AppLock to control the application being locked so it can prevent the application from exiting, Enter AppLock- AppLock launches the application and has to wait until it has created and initialized its main window.
Page 108 Message Explanation and/or corrective action Level LOG_PROC- Exit password timeout Exiting password timeout processing. ESSING LOG_PROC- Exit restart app timer Processing is at the end of the timer function ESSING LOG_PROC- Exit TaskbarScreenMode Exiting the function that switches the screen mode back to normal operation for the administrator. ESSING LOG_PROC- Exit ToAdmin...
Page 109 Message Explanation and/or corrective action Level Keyboard hook loaded OK The keyboard hook dll exists and loaded successfully. LOG_EX L after Ctrl Processing the backdoor entry. LOG_EX When AppLock first loads, it loads a dll that contains the keyboard hook processing. This message is logged LOG_PROC- Loading keyboard hook prior to the load attempt.
Page 110 Message Explanation and/or corrective action Level Switching to admin- The keyboard hook load failed, so AppLock switches to admin mode. If a password is specified, the password LOG_PROC- kbdhook.dll not found prompt is displayed and remains until a valid password is entered. ESSING Switching to admin-key- If the keyboard hook initialization fails, AppLock switches to admin mode.
Page 111: Backlight
Power key press. When the MX9 is on battery power and the backlight timer expires, the display and the backlights for the display and keypad are turned off. Default value is 30 seconds and both the check boxes are enabled. Adjust the settings and tap OK to save the changes.
Page 112: External Power
When the MX9 is on external power and the backlight timer expires, the display and the backlights for the display and keypad are turned off. Default value is 1 minute and both the check boxes are enabled. Adjust the settings and tap ok to save the changes.
Page 113: Bluetooth
Bluetooth Start > Settings > System > Bluetooth Note: Contact technical assistance for upgrade availability if your Bluetooth panels are not the same as the panels presented in this section. Discover and manage pairing with nearby Bluetooth devices. Factory Default Settings Discovered Devices None Settings...
Page 114 It is not necessary to disconnect a paired scanner and printer before a different scanner or printer is paired with the MX9. The target Bluetooth device should be as close as possible (up to 32.8 ft (10 meters) Line of Sight) to the MX9 during the pairing process.
Page 115: Initial Configuration
LED on the device, or a dialog box is placed on the MX9 display. Whenever the MX9 is turned On, all previously paired, live, Bluetooth devices in the vicinity are paired, one at a time, with the MX9.
Page 116: Bluetooth Devices
Bluetooth Devices The Bluetooth Devices tab displays any device previously discovered and paired with the MX9. Before Discover (or initial setup) After Discover Clear Button Deletes all devices from the Device table that are not currently paired. A dialog box is presented.
Page 117: Discover Button
When an active paired device enters Suspend Mode, is turned Off or leaves the MX9 Bluetooth scanning range, the Bluetooth connection between the paired device and the MX9 is lost. There may be audible or visual signals as paired devices disconnect from the MX9.
Page 118: Bluetooth Device List
An icon with a red background indicates the device's Bluetooth connection is inactive. An icon with a white background indicates the device is connected to the MX9 and the device's Bluetooth connection is active. Double-click a device in the list to open the device properties menu. The target device does not need to be active.
Page 119: Bluetooth Device Menu
Stop the connection between the MX9 and the highlighted paired Bluetooth device. Remove an unpaired device from the Bluetooth device list. The highlighted device name Delete and identifier is removed from the MX9 Bluetooth Devices panel when the user taps the Clear button. Properties More information on the highlighted Bluetooth device.
Page 120: Bluetooth Properties
Bluetooth Properties Data on the Bluetooth Properties panel cannot be changed by the user. The data displayed is the result of the device Query performed during the Discovery process. The Status dialog box reflects the current state of the highlighted device. 4-82...
Page 121: Settings
Settings Filtered Mode Off Filtered Mode On Note: These options can still be checked or unchecked whether Bluetooth connection is enabled or disabled. Turn On Bluetooth Tap the button to toggle the Bluetooth client On. The button title changes from Turn On Bluetooth to Turn Off Bluetooth. Default The default value is Disabled (Bluetooth client is Off).
Page 122: Options
Enable this option to ensure other devices can discover the MX9. This option is Enabled (checked) by default. A dialog box appears on the MX9 screen notifying the user a Bluetooth device requests to pair with the MX9. The requesting Bluetooth device does not need to have been Discovered by the MX9 before Prompt if devices request to the pairing request is received.
Page 123: Reconnect
Reconnect Note: These options can still be checked or unchecked whether Bluetooth connection is enabled or disabled. 4-85...
Page 124: Options
Options Option Information This option is Enabled by default. There may be an audio or visual signal when a connection between a paired, active device is Report when connection lost. lost A visual signal may be a dialog box placed on the display notifying the user the connection between one (or all) of the paired Bluetooth devices has stopped.
Page 125: About
Setup the Bluetooth module to establish how the user is notified by easy pairing and auto-reconnect events. AppLock, if installed, does not stop the end-user from using the Bluetooth application, nor does it stop other Bluetooth-enabled devices from pairing with the MX9 while AppLock is in control. 4-87...
Page 126: Bluetooth Indicators
When an active paired device enters Suspend Mode, is turned Off or leaves the MX9 Bluetooth scan range, the Bluetooth connection between the paired device and the MX9 is lost. There may be audible or visual signals as paired devices disconnect from the MX9.
Page 127: Bluetooth Bar Code Reader Setup
To open the LXEZ Pairing program, tap Start > Settings > System > Bluetooth or tap the Bluetooth icon at the bottom of the Today panel. Locate the bar code label, similar to the sample shown above, attached to the MX9. The label is the Bluetooth address identifier for the MX9.
Page 128: Mx9 With Label
1. Scan the Bluetooth address bar code label, attached to the MX9, with the Bluetooth mobile scanner. 2. If this is the first time the Bluetooth scanner has scanned the MX9 Bluetooth label, the devices are paired. See section titled “Bluetooth Beep and LED...
Page 129: Mx9 Without Label
The devices are paired. The Bluetooth bar code reader responds with a series of beeps and LED flashes. Note: After scanning the MX9 Bluetooth label, if there is no beep and no LED flash from the Bluetooth device, the devices are currently paired.
Page 130: Bluetooth Reader Beep And Led Indications
Bluetooth product help. Note: If there is no beep or no LED flash from the Bluetooth managed printer, the MX9 and the printer are currently paired. No more than 32.80 feet (10 meters) line of sight in a quiet environment.
Page 131: Certificates
This panel lists any installed Personal certificates. Personal certificates are used to identify the user of the device. To install a User certificate: 1. Copy the .pfx or .p12 file to a folder on the MX9. 2. Use File Explorer to browse to the location of the file and open the file by tapping the file name.
Page 132: Intermediate
To install an Intermediate certificate: 1. Copy a DER-encoded .cer file, a base64-encoded .cer file or a .pfx file to a folder on the MX9. 2. Use File Explorer to browse to the location of the file and open the file by tapping the file name.
Page 133: Root
To install a Root certificate: 1. Copy a DER-encoded .cer file, a base64-encoded .cer file or a .pfx file to a folder on the MX9. 2. Use File Explorer to browse to the location of the file and open the file by tapping the file name.
Page 134: Encryption
Encryption Start > Settings > System > Encryption This panel enables or disables encryption of data files on removable storage cards. The default is Disabled. There may be a delay while files on removable storage cards are encrypted. Note: Tap Start > Help for context sensitive Windows Mobile Help when changing or viewing options. Tap the X icon in the top right corner to close Windows Mobile Help.
Page 135: External Gps
External GPS Start > Settings > System > External GPS Factory Default Settings GPS Program Port None GPS Hardware Port None Baud Rate 4800 Access Automatic This panel configures serial GPS access over hardware serial ports using the Microsoft GPS manager. The port used, baud rate and port sharing must be specified.
Page 136: Access
Access Note: Tap Start > Help for context sensitive Windows Mobile Help when changing or viewing options. Tap the X icon in the top right corner to close Windows Mobile Help. 4-98...
Page 137: License Manager
Following image is a sample screen. Your License Manager panel may show more tabs, e.g., RFTerm, depending on the number of software applications running on the MX9 that require a license. Contact technical assistance for software updates and releases as they become available.
Page 138: Managed Programs
Managed Programs Start > Settings > System > Managed Programs This panel displays the install history for .NET managed programs. The list is read only. See Also: "Remove Programs" Note: Tap Start > Help for context sensitive Windows Mobile Help when changing or viewing options. Tap the X icon in the top right corner to close Windows Mobile Help.
Page 139: Memory
Memory Start > Settings > System > Memory These panels report the current state of virtual memory. Main The split between Storage memory and Program memory is not adjustable. 4-101...
Page 140: Storage Card
Storage Card The pop-up list shows all mounted storage, both fixed and removable. The Find prompt at the bottom of the screen launches the Search utility. Note: Tap Start > Help for context sensitive Windows Mobile Help when changing or viewing options. Tap the X icon in the top right corner to close Windows Mobile Help.
Page 141: Mixer
Start > Settings > System > Mixer The MX9 has a speaker located above the scan button. It is active when a headset is not connected to the device. Use the settings on these panels to adjust the volume, record gain and sidetone for microphone input, speaker and speaker output.
Page 142: Mx9Wm Options
MX9WM Options Start > Settings > System > MX9WM Options Set MX9 specific device options. Options that cannot be edited by the user are dimmed. Contact technical assistance enhancements and updates as they become available. Communication By default, TCP/IP version 6 is enabled and dimmed on the MX9.
Page 143: Misc
Misc. CapsLock and Touch Screen Disable are disabled and dimmed. Enable Keypad Backlight is enabled by default. Uncheck this checkbox to disable the keypad backlight. Enable Ethernet on AC Power and Battery are enabled and dimmed. Only power key resumes is disabled by default. Check this checkbox to make the power key the only event to wake up from Suspend (wake on touch or key press are disabled).
Page 144: Status Popup
Status Popup When the Status popup window is enabled, and displayed, it is placed on top of the window in focus and hides any data beneath it. The Status Popup window is closed by pressing the assigned Status User or Status Admin key sequence. Note: Use a Diamond key for the assigned key sequence to use when opening and closing the popup.
Page 145: Peripherals
Peripherals Start > Settings > System > Peripherals This panel is used to enable and disable the touch screen heater and scan window heater, flashlight time delay to Off, and GPS On/Off. Settings have no effect if module is not installed. Factory Default Settings Heaters Touch screen heater...
Page 146: Flashlight
Flashlight Note: Setting has no effect if the flashlight is not installed. Select an option to set the timeout for the flashlight. Options are: 1 minute 2 minutes 3 minutes 4-108...
Page 147: Gps
GPS presence is displayed on the GPS panel. Power can be toggled on or off only when a GPS is installed. The default setting is Off. 4-109...
Page 148: Regional Settings
Regional Settings Start > Settings > System > Regional Settings 4-110...
Page 149 Note: Tap Start > Help for context sensitive Windows Mobile Help when changing or viewing options. Tap the X icon in the top right corner to close Windows Mobile Help. 4-111...
Page 150: Registry
Registry Start > Settings > System > Registry Choose an MX9 software reload scheme. Contents When clicked, a standard load file dialog is opened, to allow the user to pick a Registry Save (.RSG) file. The Load User applet then copies the specified User registry file to the Active registry. The user is asked to verify a reboot, and Defaults then the applet does a warmboot to activate the new registry.
Page 151: Remove Programs
Remove Programs Start > Settings > System > Remove Programs This panel is used to uninstall programs. The Remove Program listing is for all programs installed via ActiveSync or via a CAB file. Note: Tap Start > Help for context sensitive Windows Mobile Help when changing or viewing options. Tap the X icon in the top right corner to close Windows Mobile Help.
Page 152: Screen
Screen Start > Settings > System > Screen General 4-114...
Page 153: Align Screen
Align Screen Tap the Align Screen button. The align screen opens and displays a large cross-hair in the middle of the screen. Tap the middle of the cross-hair as it moves around the screen. When the process is complete, the General screen is displayed. Tap ok and the changes are saved.
Page 154: Clear Type
Clear Type 4-116...
Page 155: Text Size
Text Size Tap the marker and slide it across the bar. As the marker moves, the example text increases or decreases. Tap ok and the change is saved. The new text size is in effect immediately. Note: Tap Start > Help for context sensitive Windows Mobile Help when changing or viewing options. Tap the X icon in the top right corner to close Windows Mobile Help.
Page 156: Task Manager
Task Manager Start > Settings > System > Task Manager This panel displays all running tasks as well as the memory and CPU bandwidth being used by each task. Tapping on the column headings at the top of the screen sorts the tasks by the contents of that column. Tapping the same heading a second time reverses the sort order of that column.
Page 157: Wi-Fi
Start > Settings > System > WAN These panels can be used to set the parameters for the wireless Wide Area Network (WAN) on the MX9. The WAN is a form of wireless network that utilizes a cellular network instead of the spread spectrum network most used by wireless Local Area Networks (LAN).
Page 158: Initial Setup
Initial Setup 1. Enable the radio by clicking the Admin Login button on the Connection panel (the Connect button is dimmed). 2. Enter the password in the Admin Password Entry popup text box. The default case-sensitive password is LXEWWAN. The Connect button is enabled. 3.
Page 159: Connection
Connection The Connect button controls Connect/Disconnect operation and the caption of the button changes based on the connection status. The Connect button is dimmed when the radio is disabled or absent. Click the Connect button to begin a connection with a WWAN. The button caption changes to Disconnect. Clicking the Admin Login button displays the Admin Password Entry popup text box.
Page 160: Network
Network Enter the following information for the MX9: Phone (data access number) Username Password APN (Access Point Name) Note: Some fields may not require an entry. Contact your system administrator for the information needed. 4-122...
Page 161: Tcp/Ip
TCP/IP The TCP/IP tab contains a checkbox for indicating that TCP/IP parameters are to be obtained from the network DHCP server. This tab also contains fields for entering a static IP address and the addresses of the primary and secondary DNS servers, if DHCP and DNS are not used.
Page 162: Autoconnect
Autoconnect The Autoconnect tab contains two checkboxes. Automatically connect to network when device is turned on. When this checkbox is enabled (checked) the radio automatically connects to the network when the device is turned on (power button is pressed). Automatically reconnect to network when connection lost or resuming from suspend. When this checkbox is enabled, the radio automatically attempts to reconnect to the network when it is resumed after being in the suspend state.
Page 163: Admin
SIM card PIN number entry is locked from further use. If the radio is disabled, entering and submitting the PIN saves the PIN value on the MX9. The next time the radio is enabled and requires a PIN, the saved PIN will be sent and a PIN will not need to be entered again.
Page 164: About
About The About tab displays information about the WWAN radio and the current network connection. The About tab displays the SW Version, FW Version and Serial Number of the radio if there is a WAN radio installed in the device. the Local Phone Number shows the subscriber’s own number from the SIM card.
Page 165: Connections Panel
Note: The MX9 does not support beaming. The default setting for Beam Settings is Disabled as the MX9 does not support beaming. oBject EXchange - a communications protocol used to exchange information between mobile devices. The device must sup- port infrared communication.
Page 166: Connections
Connections Start > Settings > Connections > Connections Configure connections to a host PC. Advanced Panel Options 4-128...
Page 167 Note: Tap Start > Help for context sensitive Windows Mobile Help when changing or viewing options. Tap the X icon in the top right corner to close Windows Mobile Help. 4-129...
Page 168: Domain Enroll
Domain Enroll Start > Settings > Connections > Domain Enroll Enroll in Active Directory. To begin enrollment, tap Enroll in the Status bar. Please contact your system administrator for the applicable information to complete the screens. Note: Tap Start > Help for context sensitive Windows Mobile Help when changing or viewing options. Tap the X icon in the top right corner to close Windows Mobile Help.
Page 169: Network Cards
Network Cards Start > Settings > Connections > Network Cards This panel displays a listing of network adapters. The list is based on drivers installed in the registry whether the adapter is actually supported by the hardware or not. The Network Cards may not always be displayed. If this icon is not displayed, access Network Cards by selecting Start > Settings >...
Page 170 Note: Tap Start > Help for context sensitive Windows Mobile Help when changing or viewing options. Tap the X icon in the top right corner to close Windows Mobile Help. 4-132...
Page 171: Wireless Manager
Wireless Manager Start > Settings > Connections > Wireless Manager Provides information on the currently connected wireless network(s). The following image is an example only. If more than one wireless device is being managed, the All bar is displayed. Tap the All bar to disable/enable all wireless devices at once.
Page 172 The Bluetooth radio is off The Bluetooth radio is on Visible The MX9 is discoverable If the Bluetooth radio is Off, tapping the Bluetooth bar turns the radio On. Once the radio is On, it may cycle to Visible if the MX9 is discoverable.
Page 173: Miscellaneous Start Panels
Standard Microsoft Applications Note: The intent of this segment is to document standard Microsoft applications loaded on the MX9. Documentation only consists of a panel and minimal explanation. These are standard Microsoft small form applications for which help is available on the MX9 and the Internet.
Page 174 Address book application. Can be synchronized with PC Outlook address book using ActiveSync. Email application. Can be synchronized with PC Outlook email using ActiveSync or it can synchronize with an Exchange server. 4-136...
Page 175 Displays a structured picture of files on the system. This application provides several wizards to walk a user through device configuration. 4-137...
Page 176 Access Windows Mobile help system on the MX9. Options to search using Windows Live Search are available. Windows Live Messenger. Instant Messaging service. Internet access required. Not supported on the MX9. 4-138...
Page 177 Notes. Notebook application. Select Menu > View Recording Toolbar to create an audio note. Can be synchronized with PC Outlook notes using ActiveSync. Pictures and Video. Picture/video viewer application. Can be syn- chronized with PC My Documents folder using ActiveSync. 4-139...
Page 178 Tasks. Task list application. Can be synchronized with PC Outlook task list using ActiveSync. Text Messaging application. Can be synchronized with PC Outlook email using ActiveSync or it can synchronize with an Exchange server. 4-140...
Page 179 Windows Live. Sign in to Microsoft Windows Live online service. Internet access required. Windows Media. Audio visual management program. Not supported on the MX9. 4-141...
Page 180: Internet Explorer Mobile
Internet Explorer Mobile Start > Internet Explorer Set options for Internet connectivity. The navigation icons change state based on the web page contents. Navigation Icon Action Navigation Icon Action Add folder Favorites Add to Favorites Options Go Back Soft Input Panel Delete Favorite Zoom In / Zoom Out 4-142...
Page 181: Options
Options 4-143...
Page 182 4-144...
Page 183: Office Mobile
Office Mobile A suite of business related applications. Files can be created, opened, viewed, saved in different formats, etc. Note: For Microsoft Office Mobile instruction for Word, PowerPoint, Excel and OneNote, please refer to commercially available Microsoft Office Mobile user guides. Excel Mobile Spreadsheets can be edited, data can be sorted, formatting and changes are preserved.
Page 184: Powerpoint Mobile
PowerPoint Mobile Open, view and edit slides in landscape or portrait format. Zoom and GoTo features enabled. Select Menu > Options to change default settings. Word Mobile Open, view, edit documents. Formats are saved. Spelling checker, cut and paste are available, undo and redo commands. Select Menu >...
Page 185: Onenote Mobile
OneNote Mobile Open, view, edit text-only notes. Select Menu to change default settings. 4-147...
Page 186: Remote Desktop
For example, instead of running Word Mobile on the MX9, you can run the desktop computer version of Word and access all of the .doc files on that computer from your device.
Page 187: Connect To A Remote Server
Connect to a Remote Server 1. Configure the radio. 2. Enter the name of the computer to which you want to connect. If needed, enter the port number at the end of the computer name (remotecomputername:portnumber). 3. Enter the user name, password and domain. 4.
Page 188 4-150...
Page 189: Chapter 5 - Using Activesync
Windows 7 operating system on your desktop/laptop, replace ActiveSync with Windows Mobile Device Center. Using Microsoft ActiveSync, you can synchronize information on your desktop computer with the MX9 and vice versa. Synchronization compares the data on your mobile device with your desktop computer and updates both with the most recent data.
Page 190: Initial Setup
Connect the USB cable to the PC (the host) and the mobile device (the client) as detailed below. USB will start automatically when the USB cable is connected. When the MX9 loses connection, e.g., enters Suspend Mode, etc., the connection to ActiveSync will be lost. When the MX9 resumes, the ActiveSync session will automatically re-connect.
Page 191: Explore
Explore From the ActiveSync Dialog on the Desktop PC, tap the Explore button, which allows you to explore the mobile device from the PC side, with some limitations. You can copy files to or from the mobile device by drag-and-drop. You will not be allowed to delete files or copy files out of the \Windows folder on the mobile device.
Page 192: Disconnect
Open the status bar icon in the lower right hand corner of the status bar. Then tap the Disconnect button. When the MX9 loses connection, e.g., enters Suspend Mode, etc., the connection to ActiveSync will be lost. When the MX9 resumes, the ActiveSync session will automatically re-connect.
Page 193: Configuring The Mx9 With Hsmconnect
Windows Mobile Device Center (version 6.1 or higher) is required for a Windows Vista/Windows 7 desktop/laptop computer. ActiveSync is already installed on the MX9. The MX9 is preconfigured to establish a USB ActiveSync connection to a host PC when the USB cable is attached to the MX9 and the host PC.
Page 194: Using Hsmconnect
Using HSMConnect 1. Power up the MX9. 2. Connect the MX9 to the host PC using the USB connection cable. Once connected, the ActiveSync dialog box appears and the ActiveSync connection is automatically established. 3. Select “No” for partnership when prompted. Dismiss any ActiveSync dialog boxes warning a partnership is not set up. It is not necessary to establish a partnership to use HSMConnect.
Page 195 6. Click the OK button to dismiss the About CERDisp dialog box on the MX9 desktop by clicking the OK button in the HSMConnect window on the PC desktop. The dialog box automatically times out and disappears after approximately 20 seconds.
Page 197: Chapter 6 - Data Collection
Symbol Multi-Range "LORAX" Laser, 1524ER Hand Held Products 2D Area Imager, 5300. The integrated scan engine activates when the Scan button on the front of the MX9 is depressed or when the trigger on an installed trigger handle is depressed.
Page 198: Return To Factory Default Settings
Return to Factory Default Settings After scanning the engine-specific bar code to return the scanner/imager to factory default settings, the next step is to open the bar code wedge panel on the mobile device collecting the scanned data. Click the OK button to close the panel. This action will synchronize all scanner formats for your device.
Page 199: Main Tab
The Data Collection Wedge supports up to three concurrent data collection devices. For example, the internal scanner could be used to collect data at the same time a Bluetooth scanner is paired and/or a serial device is attached to COM1. The MX9 must be in a desktop cradle to use a tethered scanner.
Page 200: Continuous Scan Mode
Start > Settings > System > Data Collection > Main Continuous scan mode is only available if the MX9 is equipped with a Symbol scanner. Continuous scan mode draws power from the main battery every time a scan read/decode sequence is performed.
Page 201: Com1 Tab
COM1 Tab Start > Settings > System > Data Collection > COM1 tab Factory Default Settings Baud Rate 9600 Data Bits Stop Bits Parity None Integrated laser scanner default values are 9600 Baud, 8 data bits, 1 stop bit and No parity. If these values are changed, the default values are restored after a cold boot or reflashing.
Page 202: Notification Tab
Notification Tab Start > Settings > System > Data Collection > Notification tab Factory Default Settings Enable Internal Scanner Sound Enabled Good Scan Vibration Bad Scan Vibration This panel toggles internal scanner sounds on and off. Internal scanner sound, by default, is enabled. Enable Good scan vibration or Bad scan vibration when a tactile response on a good scan or bad scan is desired.
Page 203 Volume and Vibration Since the Data Collection Wedge uses the operating system interface to sound beeps, if the volume/vibrate icon is set to anything other than On, Wedge beeps do not sound. Wedge vibration is not affected by these settings.
Page 204: Data Options Tab
MX9 with any other imager/scanner Note: The HHP Properties button is only present if the MX9 is equipped with a Hand Held products imager. Choose an option in the Enable Code ID drop-down box: None, AIM, Symbol, HHP or Custom.
Page 205: Enable Code Id
Enabling or disabling a specific bar code symbology at the scanner/imager is done manually using the configuration bar code in the Integrated Scanner Programming Guide. For MX9 with Hand Held Products Decoding Engine Data Collection Wedge enables or disables the bar code at the imager as well as enabling or disabling the bar code processing in the Wedge software.
Page 206: Buttons
This allows custom IDs, based on actual code IDs, to be processed before the Code ID. The external scanner operation cannot be controlled by the MX9 scanner driver; therefore, a ‘good’ beep may be sounded from the external scanner even if a bar code from an external scanner is rejected because of the configuration specified.
Page 207: Symbology Settings
Symbology Settings Start > Settings > System > Data Collection > Symbology Settings button The Symbology selected in the Symbology drop down list defines the symbology for which the data is being configured. The features available on the Symbology panel include the ability to individually enable or disable a bar code from scanning, set the minimum and maximum size bar code to accept, strip Code ID,...
Page 208: Advanced Button
Advanced Button If there are advanced configuration options for the selected symbology, an Advanced button is displayed in the lower right corner of the panel. Not all bar code symbologies have configuration parameters so the Advanced button is not present for all symbologies.
Page 209: Enable, Min, Max
Enable, Min, Max Enable This checkbox enables (checked) or disables (unchecked) the symbology field. The scanner driver searches the beginning of the bar code data for the type of ID specified in the Data Options tab -- Enable Code ID field plus any custom identifiers. When a code ID match is found as the scanner driver processes incoming bar code data, if the symbology is disabled, the bar code is rejected.
Page 210: Strip Leading/Trailing Control
Strip Leading/Trailing Control Start > Settings > System > Data Collection > Symbology button This group of controls determines what data is removed from the collected data before the data is buffered for the application. When all values are set, Code ID takes precedence over Leading and Trailing; Barcode Data stripping is performed last. Stripping occurs before the Prefix and Suffix are added, so does not affect them.
Page 211: Barcode Data Match List
Barcode Data Match List Barcode Data Panel This panel is used to strip data that matches the entry in the Match list from the bar code. Enter the data to be stripped in the text box and tap the Insert or Add button. The entry is added to the Match list. To remove an entry from the Match list, highlight the entry in the list and tap the Remove button.
Page 212: Barcode Data Match Edit Buttons
Barcode Data Match Edit Buttons Entering data into the text entry box enables the Add button. Tap the Add button and the data is added to the next empty location in the Custom ID list. Tap on an empty line in the Custom ID list. The Add button changes to Insert. Enter data into both Insert the Name and ID Code fields and tap the Insert button.
Page 213: Match List Rules
Match List Rules The data in the match list is processed by the rules listed below: Strings in the list will be searched in the order they appear in the list. If the list contains ABC and AB, in that order, incoming data with ABC will match first, and the AB will have no effect.
Page 214: Add Prefix/Suffix Control
Add Prefix/Suffix Control Note: Non-ASCII equivalent keys in Key Message mode are unavailable in this option. Non-ASCII equivalent keys include the function keys (e.g., <F1>), arrow keys, Page up, Page down, Home, and End. Use this option to specify a string of text, hex values or hat encoded values to be added to the beginning (prefix) or the end (suffix) of the bar code data.
Page 215: Symbologies
Symbologies The Code ID drop-down box filters the available symbologies, in the Symbology drop down box, by the selected Code ID. When a Hand Held Products imager scan engine is installed, AIM, Custom and HHP symbologies are displayed. HHP does not support Symbol IDs.
Page 216: Hhp Symbologies
HHP Symbologies Advanced properties are available when an integrated Hand Held Products imager is installed. Advanced properties are applicable regardless of the ID type selected (AIM or HHP). HHP = Hand Held Products. Not all HHP symbologies have Advanced options. Click the symbology link in the table below for the symbology Advanced options.
Page 217 Codabar Check Character Required – When enabled, the check character is required. Default is disabled. Transmit – When enabled, the check character is transmitted. Default is disabled. Start / Stop Character Transmit – When enabled, the start / stop characters are transmitted. Default is disabled.
Page 218 Code 39 Check Character Required – When enabled, the check character is required. Default is disabled. Transmit – When enabled, the check character is transmitted. Default is disabled. Transmit Start / Stop Character – When enabled, the start / stop characters are transmitted.
Page 219 EAN 13 Transmit Check Character – When enabled, transmit the check character. Default is disabled. Addenda Read 2-Digit – When enabled, transmit the 2 digit addenda. Default is disabled. Read 5-Digit – When enable, transmit the 5 digit addenda. Default is disabled. Required –...
Page 220 Mesa UPCA – When enabled, decode UPCA Mesa. Default is disabled. EAN13 – When enabled, decode EAN 13 Mesa. Default is disabled. Code39 – When enabled, decode Code 39 Mesa. Default is disabled. Code128 – When enabled, decode Code 128 Mesa. Default is disabled. Interleaved 2 of 5 –...
Page 221 Planet (PostaL AlphaNumeric Encoding Technique) Transmit Check Character – When enabled, transmit the check character. Default is disabled. Posicode Limited Labels – Select the type of Posicode Limited labels: None A – Posicode Limited A B – Posicode Limited B 6-25...
Page 222 Telepen Original Output – When enabled, output is Original Telepen. When disabled, output is AIM. Default is enabled. UPCA Transmit Check Character – When enabled, transmit the check character. Default is enabled Transmit Number System Digit – When enabled, transmit the number system digit.
Page 223 UPCE0 Note: The UPCE0 and UPCE1 parameters are always set to match each other. Therefore if a change is made to a parameter to either the EPCE0 or UPCE1 Advanced Properties that same change is automatically made to the Advanced Properties for the other symbology.
Page 224: Ocr Symbology
OCR Symbology Font – Font selection: Disabled A = OCR A B = OCR B Money = OCR Money MICR = Magnetic Ink Character Recognition Default is disabled. Direction – Decoder reads OCR fonts in any direction, but setting direction parameter correctly can increase decoding speed: Left to Right Top to Bottom...
Page 225: Ocr Template Examples
OCR Template Examples To read a combination of 6 alpha and numeric characters use the following template: aaaaaa To read the same string with a modulo 10 check digit in the 7 character position, use the following template: aaaaaac Then enter 0123456789 for the Check parameter. To read either a string of 6 alphabetic letters OR a string of 8 numeric digits, use this template: lllllltdddddddd Note the use of the “t”...
Page 226: Ctrl Char Mapping
Ctrl Char Mapping The Ctrl Char Mapping button activates a dialog to define the operations the Data Collection Wedge performs on control characters (values less than 0x20) embedded in bar codes. Control characters can be replaced with user-defined text which can include hat encoded or hex encoded values.
Page 227: Translate All
Translate All When Translate All is checked, unprintable ASCII characters (characters below 20H) in scanned bar codes are assigned to their appropriate CTRL code sequence when the bar codes are sent in Character mode. The wedge provides a one-to-one mapping of control characters to their equivalent control+character sequence of keystrokes. If control characters are translated, the translation is performed on the bar code data, prefix, and suffix before the keystrokes are simulated.
Page 228: Custom Identifiers
Custom Identifiers Code IDs can be defined by the user. This allows processing parameters to be configured for bar codes that do not use the standard AIM or Symbol IDs or for bar codes that have data embedded at the beginning of the data that acts like a Code ID. These are called “custom”...
Page 229 Parameters Name text box Name is the descriptor that is used to identify the custom Code ID. Names must be unique from each other; however, the Name and ID Code may have the same value. Name is used in the Symbology drop down box to identify the custom Code ID in a user-friendly manner.
Page 230: Control Code Replacement Examples
Control Code Replacement Examples Configuration Example Con- Example con- Translation Translated data data trol Character figuration The control character is discarded from 0x1B in the bar code is dis- Ignore(drop) ESCape ‘Ignore (drop)’ the bar code data, prefix and suffix carded.
Page 231 Bar Code Symbology Raw Scanner Data Resulting Data EAN-128 ]C11234567890123 bbb1234567890xxx EAN-128 ]C111234567890123 bbb11234567890xxx EAN-128 ]C1123 < rejected > (too short) EAN-13 ]E01234567890987 ccc]E04567890yyy EAN-13 ]E01231234567890987 ccc]E0234567890yyy EAN-13 ]E01234 ccc]E0yyy I2/5 ]I04444567890987654321 < rejected > (too long) I2/5 ]I04444567890123 ddd7890zzz I2/5 ]I0444 dddzzz...
Page 232: Hhp Properties
HHP Properties When the MX9 is equipped with a Hand Held Products imager, this option is used to configure imager parameters. Option Action Centering The centering feature is used to allow the user to accurately scan a selected bar code among a group of bar codes that are located closely together.
Page 233 Option Action Mode In Standard mode the imager will decode both linear and 2-D symbologies. In Aggressive Linear Decode mode the imager will only read linear symbologies in this mode, but decoding these is faster and more accurate than Standard Mode. In Quick Omni mode the imager searches for a bar code in a reduced field located around the center of the image.
Page 234: Length Based Bar Code Stripping
Length Based Bar Code Stripping Use this procedure to create symbology rules for two bar codes with the same symbology but with different discrete lengths. This procedure is not applicable for bar codes with variable lengths (falling between a maximum value and a minimum value). Example 1: A normal AIM or Symbol symbology role can be created for the desired bar code ID.
Page 235 Tap the Barcode Data button. Tap the Add button. Add the data for the match codes. Refer to the previous section Bar Code Data Match List for instruction. Scan a bar code and examine the result. 6-39...
Page 236: Processing Tab
Processing Tab The Processing tab contains a user configurable key delay that applies to scanned bar codes as they are input when Remote Desktop is the application with the input focus. Factory Default Settings Enable buffered key output Enabled Same buffer limit (characters) Delay between (key) buffers 75 ms Enable only in Remote Desktop...
Page 237: About Tab
About Tab The About tab lists the version of the Data Collection Wedge (DCWedge) software and the type of scanner/imager installed in the MX9. Symbol Scanner Hand Held Products Imager Valid scanner / imager types: HHP – Hand Held Products 5300 2D Imager Symbol - Symbol SE955 Symbol –...
Page 238: Hat Encoding
Hat Encoding Hat Encoded Characters Hex 00 through AD 6-42...
Page 239 Hat Encoded Characters Hex AE through FF 6-43...
Page 240 6-44...
Page 241: Chapter 7 - Enhanced Launch Utility
Chapter 7 - Enhanced Launch Utility Introduction The launch utility on the MX9 has two functions: Process registry based Launch items Process script based Launch items. The registry based Launch items are processed before the script based Launch items. Registry Based Launch Items Note: The Registry based Launch items (documented here) are processed before the Script Based Launch items.
Page 242 The auto-launch process is as follows. 1. The launch utility opens the registry database and reads the list of CAB files to auto-launch. 2. First it looks for FileName to see if the CAB file is present. If not, the registry entry is ignored. If it is present, and the Installed flag is not set, auto-launch makes a copy of the CAB file (since it gets deleted by installation), and runs the Microsoft utility WCELOAD to install it.
Page 243: Launch Startup Options
Launch Startup options The Launch utility uses registry entries to enable or disable startup options. These flags are located in the registry key: HKEY_LOCAL_MACHINE\Software\LXE\Launch These can be configured using RegEdit. The options are as follows: Ship Value Description Default LaunchPSM Execute the Persist keys JumpStart Look for and execute JumpStart scripts...
Page 244: Script Based Launch Items
Script Based Launch Items Note: The Script Based Launch items (documented here) are processed after the Registry Based Launch items (documented earlier). The Enhanced (script based) portion of the Launch utility provides several features: Launch .CAB file Run .EXE file Run .EXE file using specified parameters Run .BAT file Process .REG file...
Page 245: File Names
File Names From a Cold Boot it looks for JmpStart.cld but from a Warm Boot it looks for JmpStart.wrm. The Launch program can also be run manually. Unless it is given a file as part of the command line it tries to run Launch.txt. The script file may be in ASCII or Unicode.
Page 246: Commands Supported By Launch
Commands Supported by Launch Copy ElseIfFIile IfFile Mkdir Delete EndIf IfTerm Rmdir DelRegData EndIfFile Launch SetRegData DelRegKey EndIfTerm LaunchCmd SetRegKey ElseIf FCopy Message Shortcut The commands supported by Launch are detailed below. Square brackets indicate that a parameter is optional. Characters in Italics represent a variable, and not a literal.
Page 247 DelRegData Description Deletes a specified registry data field. Syntax Delregdata,key,subkey,field Parameters key: The abbreviated major registry key where you want to delete a field. Can be one of: cr or hkcr (HKEY_CLASSES_ROOT) cu or hkcu (HKEY_CURRENT_USER) lm or hklm (HKEY_LOCAL_MACHINE). The case of key doesn’t matter subkey: The subkey that holds the field you want to delete.
Page 248 DelRegKey Description Deletes a specified registry subkey. Syntax DelRegKey,key,subkey Parameters key: The abbreviated major registry key where you want to delete the subkey. Can be one of: cr or hkcr (HKEY_CLASSES_ROOT) cu or hkcu (HKEY_CURRENT_USER) lm or hklm (HKEY_LOCAL_MACHINE). The case of key doesn’t matter subkey: The subkey you want to delete.
Page 249 ElseIfFIile Description Begins conditional command block executed only if the file specified in the previous IfFile does not exist. Syntax ElseIfFile Parameters None Example IfFile , below Notes Results are unpredictable if not paired properly with IfFile command. EndIf Description Ends conditional command block begun with the previous IF command.
Page 250 EndIfFile Description Ends conditional command block begun with the previous IF command. Syntax EndIfFile Parameters None Example IfFile , below Notes Results are unpredictable if not paired properly with IfFile command. EndIfTerm Description Ends conditional command block executed only if the device type specified in IfTerm matches. Syntax EndIfTerm Parameters...
Page 251 FCopy Description Copies a file, overwriting any existing file. Syntax fcopy,source-file,destination-file Parameters source-file: The file to be copied, including its path destination-file: The destination path and filename Example fcopy,\Storage Card\MyData.dat,\Temp\MyData.dat Notes If the destination file already exists it is overwritten. If the source file is blank, a zero-byte file is created.
Page 252 IfFile Description Begins the conditional execution of a block of commands only if the specified file exists. Syntax IfFile,file Parameters file: The path and filename to determine if the commands should be executed Example IfFile,\System\MyData.dat any number of commands, executed if file exists ElseIfFile any number of commands, executed if file does not exist EndIfFile...
Page 253 IfTerm Description Begins the conditional execution of a block of commands only if the terminal matches the specified terminal type. Syntax IfTerm,terminal Parameters terminal: The terminal type to determine if the commands should be executed Example IfTerm,MX3X any number of commands EndIfTerm Notes If the terminal type is identical (not case-dependent) the commands are executed.
Page 254 LaunchCmd Description Runs a program with arguments. Syntax Launchcmd,program,arguments,wait-code Parameters program: The full path and filename of the program to be run. wait-code Tells Launch how to behave when the program is running. w(ait) causes Launch to stop processing the script until the program has finished executing. c(ontinue) makes Launch continue processing the script while the program is executing.
Page 255 Mkdir Description Creates a directory. Syntax Mkdir,dir Parameters dir: The full path and name of the directory to be created. Example mkdir,\Program Files\MyApp Notes A new directory cannot be created if its parent directory doesn’t exist. For example, to create a directory called \MyApp with a subdirectory called SubDir1, use mkdir,\MyApp followed by mkdir,\MyApp\SubDir1.
Page 256 SetRegData Description Adds or updates a data field in the registry. Syntax Setregdata,key,subkey,type,field,data[,data2][,data3]... Parameters key: The abbreviated major registry key where you want to create/update the subkey. Can be one of: cr or hkcr (HKEY_CLASSES_ROOT) cu or hkcu (HKEY_CURRENT_USER) lm or hklm (HKEY_LOCAL_MACHINE). The case of key doesn’t matter subkey: The subkey you want to create/update a field in.
Page 257 SetRegKey Description Adds a sub key to the registry. Syntax Setregkey,key,subkey Parameters key: The abbreviated major registry key where you want to create the subkey. Can be one of: cr or hkcr (HKEY_CLASSES_ROOT) cu or hkcu (HKEY_CURRENT_USER) lm or hklm (HKEY_LOCAL_MACHINE). The case of key doesn’t matter subkey: The subkey you want to create.
Page 258 Shortcut Description Creates a shortcut. Syntax Shortcut,name,target Parameters name: The path and name of the shortcut file. The file name must end in .lnk for Windows to recognize it as a short- cut. target: The target of the shortcut. If the target has a space in it quote marks must be used (see Command Line Structure section and example below).
Page 259: Launch Error Messages
Launch Error Messages Launch displays a message if it encounters an error during the processing of a script. It is possible to get cascading error messages, as Launch does not stop processing the script if it encounters an error. An example of this would be a failure creating a directory causing the failure of all files copied to that directory.
Page 260 Error Message Given by Description Parms: Invalid Remove Directory RmDir Not enough parameters were supplied. Parms: Invalid Set Registry Data SetRegData Not enough parameters were supplied. Parms: Invalid User Message Message Not enough parameters were supplied. Program Launch couldn't get Exit- Launch There was a problem getting the exit status of the program.
Page 261: Example Script File
Example Script File iffile,\System\applock.cab launchcmd,\Windows\wceload.exe,"/noaskdest /noui \System\applock.cab",w launch,\Windows\applockprep.exe,c endiffile launchcmd,\Windows\wceload.exe,"/noaskdest /noui \System\wedge.cab",w iffile,\System\summit.cab launchcmd,\Windows\wceload.exe,"/noaskdest /noui \System\summit.cab",w endiffile iffile,\System\RFTerm.cab launchcmd,\Windows\wceload.exe,"/noaskdest /noui \System\RFTerm.cab",w endiffile iffile,\System\Java.cab launchcmd,\Windows\wceload.exe,"/noaskdest /noui \System\Java.cab",w launchcmd,\Windows\wceload.exe,"/noaskdest /noui \Windows\Jeode.cab",w endiffile launch,\System\regrest.exe,w coldboot 7-21...
Page 262 7-22...
Page 263: Chapter 8 - Enabler Installation And Configuration
Doing so results in unnecessary delays when booting the device. The Avalanche Enabler installation file ENABLER.CAB is loaded on the MX9 by Honeywell; however, the device is not configured to launch the Enabler installation file automatically. The installation application must be run manually the first time Avalanche is used.
Page 264: Enabler Uninstall Process
7. Reboot the MX9 if necessary. Update Monitoring Overview There are three methods by which the Enabler on the MX9 can communicate with the Mobile Device Server running on the host machine. Wired via a serial cable between the Mobile Device Server PC and the MX9.
Page 265: Mobile Device Wireless And Network Settings
Mobile Device Wireless and Network Settings Once the connection to the Mobile Device Server is established, the MX9 Enabler attempts to apply all network and wireless settings contained in the active profile. The success of the application of settings is dependent upon the local configuration of control parameters for the Enabler.
Page 266: User Interface
User Interface The Enabler can be configured and controlled manually through the user interface on the MX9. This section details the functionality that can be controlled by the user or system administrator. Parameters and Screen Displays Screen displays shown in this section are designed to present the end-user with information graphically.
Page 267: File Menu Options
Wavelink Avalanche Mobility Center User Guide for details. The Settings option under the File menu allows the MX9 user to access the control panel to locally configure the Enabler settings. The Enabler control panel is, by default, password protected.
Page 268: Avalanche Update Using File > Settings
Avalanche Update using File > Settings Use these menu options to setup the Avalanche Enabler on the MX9. Change the settings and then save the changes (reboot) before connecting to the network. Alternatively, the Mobile Device Server can be disabled until needed (refer to the Wavelink Avalanche Mobility Center User’s Guide for details).
Page 269: Connection
Connection Avalanche Enter the IP Address or host name of the Mobile Device Server assigned to the MX9. Server Address Check Serial Indicates whether the Enabler should first check for serial port connection to the Mobile Device Server Connection before checking for a wireless connection to the Mobile Device Server.
Page 270: Execution
Execution Note the dimmed options on this MX9 panel. This menu option is designed to manage downloaded applications for automatic execution upon startup. Auto-Execute An application that has been installed with the Avalanche Management system can be run Selection automatically following each boot.
Page 271: Server Contact
Sync Clock Reset the time on the MX9 based on the time on the Mobile Device Server host PC. On Startup – Connect to the Mobile Device Server when the Enabler is accessed. On Resume – Connect to the Mobile Device Server when resuming from Suspend mode.
Page 272: Data
Data The Data tab controls when data is transferred between the MX9 and the Mobile Device Server. Transfer Data When When enabled, periodic updates from the Mobile Device Server are postponed until the MX9 has been Device is Idle idle for the specified period of time. The default is disabled.
Page 273: Preferences
By default, Keep settings unlocked for 10 minutes is disabled (checkbox is blank). Application Behavior of the Enabler when the MX9 boots up. The default is Monitor for Updates. Do not Monitor - When the device boots, do not launch the Enabler application and do not attempt to connect to the Mobile Device Server.
Page 274 Activity Log Use this option to control the level of detail recorded in the log file. The default is No Activity Log. No Activity Log - No log file is written. Critical - Only critical errors written to the log files. Error - Communication or configuration problems are written to the log file along with critical Log Level messages.
Page 275: Taskbar
Taskbar For best results use AppLock to manage the taskbar. AppLock is resident on each mobile device. The Display State options control the appearance of the taskbar while using the Enabler interface. Normal - taskbar is visible, taskbar icons function normally. Hidden - taskbar is not displayed Locked - taskbar is visible, but most icons are hidden or for information only.
Page 276: Scan Config
Scan Config For best results use eXpress Config and eXpress Scan for this function. eXpress Scan is included with the updated MX9 enablers. Scan Config functionality is a standard option of the Wavelink Avalanche MC system but is not currently supported on the MX9.
Page 277: Display
Display Update Window Display The user interface for the Enabler can be configured to dynamically change based on the status of the MX9 connection with the Mobile Device Server. At startup Default is Half Screen. Options are Half screen, Hidden or Full screen.
Page 278: Shortcuts
For best results use AppLock for this function. AppLock is resident on each mobile device. Configure shortcuts to other applications on the MX9. Shortcuts are viewed and activated in the Programs panel. This limits the user’s access to certain applications when the Enabler is controlling the mobile device display.
Page 279: Saas
SaaS Use to configure the Enabler to connect with Avalanche on Demand. This is a Software-as-a-Service version of Avalanche. Using either of the SaaS configuration options below assumes the user has registered with Wavelink. Disable SaaS No SaaS connection is used. Scan Configure Scan bar codes printed from within the Avalanche Console to configure the Enabler for the SaaS con- SaaS...
Page 280: Adapters
Settings should not be checked as configuration packages provide more radio configuration options. Current Lists all network adapters currently installed on the MX9. Adapter Primary Indicates if the Enabler is to attempt to configure the primary adapter (active only if there are multiple network Adapter adapters).
Page 281 Icon When enabled, the Enabler will ignore any network or wireless settings coming from the Avalanche MC Console Manual and use only the network settings on the MX9. Settings Properties Selecting the Properties icon displays the Manual Settings Properties dialog applet. From here, the user can...
Page 282 Note: The Authentication tab may not be present in all versions of the Enabler. Enabling “Manage Wireless Settings” for Summit Client devices is not recommended. Note: When you download a profile that is configured to manage network and wireless settings, the Enabler will not apply the manage network and wireless settings to the adapter unless the global Manage wireless settings and Manage network settings options are enabled on the Adapters panel.
Page 283: Status
It also searches for new adapters and may cause a slight delay to refresh the contents of the drop-down menu. Link speed indicates the speed at which the signal is being sent from the adapter to the MX9. Speed is dependent on signal strength.
Page 284: Exit
Exit The Exit option is password protected. The default password is leave. The password is not case-sensitive. If changes were made on the MX9 Startup/Shutdown tab screen, then after entering the password, tap OK and the following screen is displayed: Change the option if desired.
Page 285: Using Remote Management
Using Remote Management 1. Configure the radio to connect to the network running the Mobile Device Server. After the MX9 is connected, proceed to step 2. 2. If it is desired to configure the radio using the Summit package, add the configured package to the Wavelink Avalanche MC Console and enable it.
Page 286: Using Express Scan
Using eXpress Scan eXpress Scan Desktop Icon If the MX9 has an eXpress Scan icon on the desktop, eXpress Scan may be used for the initial configuration of the device. If the eXpress Scan icon is not present on the desktop, install the Enabler. If the icon is still not present,...
Page 287: Step 3: Process Completion
Step 3: Process Completion After the last bar code is scanned, the settings are automatically applied. Once configured, the MX9 is warmbooted. Once connected to the wireless network and the Mobile Device Server, any software updates and additional configuration data are downloaded.
Page 288 8-26...
Page 289: Chapter 9 - Wireless Network Configuration
EAP-FAST Important Notes It is important that all dates are correct on the MX9 and host computers when using any type of certificate. Certificates are date sensitive and if the date is not correct authentication will fail. It may be necessary to upgrade radio software in order to use certain Summit Client Utility (SCU) features.
Page 290: Summit Client Utility
Note: When making changes to profile or global parameters, tap the power key to place the MX9 in Suspend. When the MX9 resumes from suspend the parameters are applied. The MX9 can be resumed by tapping the power key or the touch screen or by pressing any key.
Page 291: Summit Tray Icon
Summit Tray Icon The Summit tray icon provides access to the SCU and is a visual indicator of radio status. The Summit tray icon is displayed when: The Summit radio is installed and active The Windows Zero Config utility is not active The Tray Icon setting is On Click the icon to launch the SCU.
Page 292: Using Windows Mobile Wireless Manager
Using Windows Mobile Wireless Manager For best results use the Summit Client Utility to manage wireless connectivity. However, if desired, Windows Mobile includes the Wireless Manager utility to manage wireless network connections in place of the Summit Client Utility. To use the Windows Mobile Wireless Manager, first open the Summit Client Utility. 1.
Page 293 Enter the SSID of the desired network in the Network name text box. Be sure to check the This is a hidden network checkbox for a non-broadcast SSID. In the Connects to box, select The Internet if the MX9 connects directly to the Internet, select Work if the MX9 connects to a network (even if the network provides an Internet connection).
Page 294: Edit A Network Connection
Note: Tap Start > Help for context sensitive Windows Help when changing or viewing options. Tap the X icon in the top right corner to close Windows Help. Edit a Network Connection Double tap the network name to edit the configuration or tap the network name and tap Connect to connect to the network. Network configuration screens are the same as displayed in the previous section.
Page 295: Main Tab
Main Tab Start > Settings > System > Wi-Fi > Main tab Factory Default Settings Admin Login SUMMIT Radio Enabled Active Config/Profile Default Regulatory Domain Varies by location The Main tab displays information about the wireless client device including: SCU (Summit Client Utility) version Driver version Radio Type (BG is an 802.11 b/g radio, ABG is an 802.11 a/b/g radio).
Page 296: Auto Profile
The Disable Radio button can be used to disable the network card. Once disabled, the button label changes to Enable Radio. By default the radio is enabled. The Admin Login button provides access to editing wireless parameters. Profile and Global may only be edited after entering the Admin Login password.
Page 297: Admin Login
Admin Login To login to Administrator mode, tap the Admin Login button. Once logged in, the button label changes to Admin Logout. The admin is automatically logged out when the SCU is exited. The Admin can either tap the Admin Logout button, or the OK button to logout. The Administrator remains logged in when the SCU is not closed and a Suspend/Resume function is performed.
Page 298: Profile Tab
Profile Tab Start > Settings > System > Wi-Fi > Profile tab Note: Tap the Commit button to save changes before leaving this panel or the SCU. If the panel is exited before tapping the Commit button, changes are not saved! Factory Default Settings Profile Default...
Page 299: Buttons
Buttons Button Function Commit Saves the profile settings made on this screen. Settings are saved in the profile. Allows entry of a username and password, certificate names, and other information required to authenticate with Credentials the access point. The information required depends on the EAP type. Deletes the profile.
Page 300: Profile Parameters
WPA PSK, WPA TKIP, WPA CCKM, WPA2 PSK, WPA2 AES, or WPA2 CCKM. Encryption None CKIP is not supported in the MX9. Note: The Encryption type chosen determines if the WEP Keys / PSK Keys button is active and also determines the available entries in the WEP or PSK pop-up window.
Page 301 It is important the Radio Mode parameter correspond to the AP to which the device is to connect. For example, if this parameter is set to G rates only, the MX9 may only connect to APs set for G rates and not those set for B and G rates.
Page 302: Status Tab
Status Tab Start > Settings > System > Wi-Fi > Status tab This screen provides information on the radio: The profile being used The status of the radio card (down, associated, authenticated, etc.) Client information including device name, IP address and MAC address. Information about the Access Point (AP) maintaining the connection to the network including AP name, IP address and MAC address.
Page 303: Diags Tab
Diags Tab Start > Settings > System > Wi-Fi > Diags tab The Diags screen can be used for troubleshooting network traffic and radio connectivity issues. (Re)connect – Use this button to apply (or reapply) the current profile and attempt to associate or authenticate to the wireless LAN.
Page 304: Global Tab
Global Tab Start > Settings > System > Wi-Fi > Global tab The parameters on this panel can only be changed when an Admin is logged in with a password. The current values for the parameters can be viewed by the general user without requiring a password. Note: Tap the Commit button to save changes.
Page 305: Custom Parameter Option
Custom Parameter Option Honeywell does not support the parameter Custom option. The parameter value is displayed as “Custom” when the operating system registry has been edited to set the Summit parameter to a value that is not available from the parameter’s drop down list.
Page 306: Global Parameters
Global Parameters Parameter Default Function If signal strength is less than this trigger value, the client looks for a different Access Point with a Roam stronger signal. -65 dBm Trigger Options are: -50 dBm, -55, -60, -65, -70, -75, -80, -85, -90 dBm or Custom. The amount by which a different Access Point signal strength must exceed the current Access Roam Point signal strength before roaming to the different Access Point is attempted.
Page 307 Parameter Default Function Cisco IE = Cisco Information Element. Use of Wi-Fi Multimedia extensions. Options are: On, Off Specifies the type of authentication server. Auth Type 1 Server Options are: Type 1 (ACS server) and Type 2 (non-ACS server) Authentication method used within the secure tunnel created by EAP-TTLS. Options are: AUTO-EAP (Any available EAP method) TTLS Inner...
Page 308 Parameter Default Function If the packet size (in bytes) exceeds the specified number of bytes set in the fragment threshold, the packet is fragmented (sent as several pieces instead of as one block). Use a low setting in areas Frag 2346 where communication is poor or where there is a great deal of wireless interference.
Page 309 Parameter Default Function Options are: Any number between 0 and 30000 ms. Note: Tap the Commit button to save changes. If this panel is closed before tapping the Commit button, changes are not saved! 9-21...
Page 310: Sign-On Vs. Stored Credentials
Sign-On vs. Stored Credentials When using wireless security that requires a user name and password to be entered, the Summit Client Utility offers these choices: The Username and Password may be entered on the Credentials screen. If this method is selected, anyone using the device can access the network.
Page 311: How To: Use Sign On Screen
How to: Use Sign On Screen 1. After completing the other entries in the profile, click on the Credentials button. Leave the Username and Password blank. No entries are necessary on the Credentials screen for LEAP or LEAP/WPA. 2. For PEAP-MSCHAP and PEAP-GTC, importing the CA certificate into the Windows certificate store is optional. 3.
Page 312: Windows Certificate Store Vs. Certs Path
Windows Certificate Store vs. Certs Path Note: It is important that all dates are correct on the MX9 and host computers when using any type of certificate. Certificates are date sensitive and if the date is not correct authentication will fail.
Page 313 6. Uncheck the Use full trusted store checkbox. 7. Select the desired certificate and click the Select button to return the selected certificate to the CA Cert textbox. 8. Click OK to exit the Credentials screen and then Commit to save the profile changes. 9-25...
Page 314: Configuring The Profile
Configuring the Profile Use the instructions in this section to complete the entries on the Profile tab according to the type of wireless security used by your network. The instructions that follow are the minimum required to successfully connect to a network. Your system may require more parameters than are listed in these instructions.
Page 315: No Security
No Security To connect to a wireless network with no security, make sure the following profile options are used. Enter the SSID of the Access Point assigned to this profile Set EAP Type to None Set Encryption to None Set Auth Type to Open Once configured, click the Commit button.
Page 316: Wep
To connect using WEP, make sure the following profile options are used. Enter the SSID of the Access Point assigned to this profile Set EAP Type to None Set Encryption to WEP or Manual WEP (depending on SCU version) Set Auth Type to Open 9-28...
Page 317 Click the WEP keys/PSKs button. Valid keys are 10 hexadecimal or 5 ASCII characters (for 40-bit encryption) or 26 hexadecimal or 13 ASCII characters (for 128- bit encryption). Enter the key(s) and click OK. Once configured, click the Commit button. Ensure the correct Active Profile is selected on the Main tab and perform a Suspend/Resume.
Page 318: Leap
LEAP To use LEAP (without WPA), make sure the following profile options are used. Enter the SSID of the Access Point assigned to this profile Set EAP Type to LEAP Set Encryption to WEP EAP or Auto WEP (depending on SCU version) Set Auth Type as follows: If the Cisco/CCX certified AP is configured for open authentication, set the Auth Type radio parameter to Open.
Page 319 Enter the Domain\Username (if the Domain is required), otherwise enter the Username. Enter the password. Click OK then click the Commit button. Ensure the correct Active Profile is selected on the Main tab and perform a Suspend/Resume. The SCU Main tab shows the device is associated after the radio connects to the network.
Page 320: Peap/Mschap
PEAP/MSCHAP To use PEAP/MSCHAP, make sure the following profile options are used. Enter the SSID of the Access Point assigned to this profile Set EAP Type to PEAP-MSCHAP Set Encryption to WPA TKIP Set Auth Type to Open To use another encryption type, select WPA CCKM, WPA2 AES or WPA2 CCKM for encryption and complete other entries as detailed in this section.
Page 321 Enter the Domain\Username (if the Domain is required), otherwise enter the Username. Enter the password. Leave the CA Certificate File Name blank for now. Click OK then click Commit. Ensure the correct Active profile is selected on the Main Tab. Windows Certificate Store vs.
Page 322 Once successfully authenticated, import the CA certificate into the Windows certificate store. Return to the Credentials screen and check the Validate server checkbox. If using the Windows certificate store: Check the Use MS store checkbox. The default is to use the Full Trusted Store. To select an individual certificate, click on the Browse button.
Page 323: Peap/Gtc
PEAP/GTC To use PEAP/GTC, make sure the following profile options are used. Enter the SSID of the Access Point assigned to this profile Set EAP Type to PEAP-GTC Set Encryption to WPA TKIP Set Auth Type to Open To use another encryption type, select WPA CCKM, WPA2 AES or WPA2 CCKM for encryption and complete other entries as detailed in this section.
Page 324 Enter the Domain\Username (if the Domain is required), otherwise enter the Username. Enter the password. Leave the CA Certificate File Name blank for now. Click OK then click Commit. Ensure the correct Active Profile is selected on the Main Tab. Windows Certificate Store vs.
Page 325 Once successfully authenticated, import the CA certificate into the Windows certificate store. Return to the Credentials screen and check the Validate server checkbox. If using the Windows certificate store: Check the Use MS store checkbox. The default is to use the Full Trusted Store. To select an individual certificate, click on the Browse button.
Page 326: Wpa/Leap
WPA/LEAP To use WPA/LEAP, make sure the following profile options are used. Enter the SSID of the Access Point assigned to this profile Set EAP Type to LEAP Set Encryption to WPA TKIP Set Auth Type as follows: If the Cisco/CCX certified AP is configured for open authentication, set the Auth Type radio parameter to Open.
Page 327 Enter the Domain\Username (if the Domain is required), otherwise enter the Username. Enter the password. Click OK then click the Commit button. Ensure the correct Active Profile is selected on the Main tab and perform a Suspend/Resume. The SCU Main tab shows the device is associated after the radio connects to the network.
Page 328: Eap-Fast
RADIUS server must have auto provisioning enabled to send the PAC provisioning credentials to the MX9. For automatic PAC provisioning, once a username/password is authenticated, the PAC information is stored on the MX9. The same username/password must be used to authenticate each time. See the note below for more details.
Page 329 To use Sign-On credentials: Do not enter a User and Password as the user will be prompted for the Username and Password when connecting to the network. To use Stored Credentials: Enter the Domain\Username (if the Domain is required), otherwise enter the Username. Enter the password.
Page 330: Eap-Tls
EAP-TLS To use EAP-TLS, make sure the following profile options are used. Enter the SSID of the Access Point assigned to this profile Set EAP Type to EAP-TLS Set Encryption to WPA TKIP Set Auth Type to Open To use another encryption type, select WPA CCKM, WPA2 AES or WPA2 CCKM for encryption and complete other entries as detailed in this section.
Page 331 Enter the Domain\Username (if the Domain is required), otherwise enter the Username. Select a user certificate from the Windows certificate store. Use the Browse button to locate the User Cert from the certificate store. Highlight the desired certificate and press the Select button. The name of the certificate is displayed in the User Cert box.
Page 332 Enter the certificate filename in the CA Cert textbox. Click OK then click Commit. The MX9 should be authenticating the server certificate and using EAP-TLS for the user authentication. Ensure the correct Active Profile is selected on the Main tab and perform a Suspend/Resume.
Page 333: Wpa Psk
WPA PSK To connect using WPA/PSK, make sure the following profile options are used: Enter the SSID of the Access Point assigned to this profile Set EAP Type to None Set Encryption to WPA PSK or WPA2 PSK Set Auth Type to Open 9-45...
Page 334 Click the WEP keys/PSKs button. This value can be 64 hex characters or an 8 to 63 byte ASCII value. Enter the key and click OK. Once configured, click the Commit button. Ensure the correct Active Profile is selected on the Main tab and perform a Suspend/Resume.
Page 335: Certificates
Please refer to the Security Primer to prepare the Authentication Server and Access Point for communication. Note: It is important that all dates are correct on the MX9 and host computers when using any type of certificate. Certificates are date sensitive and if the date is not correct authentication will fail.
Page 336: Generating A Root Ca Certificate
Generating a Root CA Certificate Note: It is important that all dates are correct on the MX9 and host computers when using any type of certificate. Certificates are date sensitive and if the date is not correct authentication will fail.
Page 337 Click the Download a CA certificate, certificate chain or CRL link. Make sure the correct root CA certificate is selected in the list box. 9-49...
Page 338 To download the CA certificate, click on the Download CA certificate link. Click the Save button and save the certificate. Make sure to keep track of the name and location of the certificate. Install the certificate on the MX9. 9-50...
Page 339: Installing A Root Ca Certificate
\System folder or other path specified in the Summit Certs global parameter. Copy the certificate file to the MX9. The certificate file has a .CER extension. Locate the file and tap it. A certificate installation warning text box is displayed: Your device is being asked to install a security certificate.
Page 340: Generating A User Certificate
Generating a User Certificate The easiest way to get the user certificate is to use the browser on a PC to navigate to the Certificate Authority. To request the user certificate, open a browser to http://<CA IP address>/certsrv. Sign into the CA with the username and password of the person who will be logging into the mobile device. This process saves a user certificate file.
Page 341 Click the Request a certificate link. Click on the User Certificate link. 9-53...
Page 342 Click on the Submit button. if there is a message box asking if you want to confirm the request, click Yes. The User Certificate is issued. Install the user certificate on the requesting computer by clicking the Install this certificate link. Export the certificate as described below.
Page 343: Exporting A User Certificate
Exporting a User Certificate Start Internet Explore on the PC that requested the certificate. Select Tools > Internet Options > Content and click the Certificates button. Make sure the Personal tab is selected. Highlight the certificate and click the Export button. The Certificate Export Wizard is started Select Yes, export the private key and click Next.
Page 344: Installing A User Certificate
PC to the MX9. Copy the certificate to a location on the MX9, such as a storage card or the \System folder. Locate the certificate file (it has a .PFX extension) and tap on it. You are prompted for the password that was assigned when the certificate was exported.
Page 345: Chapter 10 - Keymaps
MX9 62-Key Keymap The following keypad keymap is used on an MX9 that is not running a Terminal Emulator. Terminal emulators use a separate keymap. A modifier key pressed after itself toggles that modifier key off. Modifier keys pressed following any other modifier key clears earlier modifier keys.
Page 346 To get this function Press these keys in this order Result / Notes Back space BS (Backspace) Back one space Backtab Orange Backtab Cursor Up Up Arrow Cursor up one line Cursor Down Down Arrow Cursor down one line Cursor Right Blue Up Arrow Cursor right one space...
Page 347 To get this function Press these keys in this order Result / Notes SHFT F24 mode a (lowercase is the default) SHFT SHFT SHFT SHFT SHFT SHFT SHFT SHFT SHFT 10-3...
Page 348 To get this function Press these keys in this order Result / Notes SHFT SHFT SHFT SHFT SHFT SHFT SHFT SHFT SHFT SHFT SHFT SHFT SHFT SHFT SHFT SHFT SHFT 0 (zero) 0 (zero) . (period) Orange Period . (period) Orange Period Blue...
Page 349 To get this function Press these keys in this order Result / Notes Orange Comma Orange Semicolon Blue Equal sign Orange Exclamation mark SHFT 1 (number) Exclamation mark Orange At sign SHFT 2 (number) At sign Orange Number sign SHFT 3 (number Number sign Orange...
Page 350: Mx9 62-Key 5250 Keypad Keymap
MX9 62-Key 5250 Keypad Keymap To get this function Press these keys in this order Result / Notes Attention (Attn) 5250 Attn Clear (Clr) 5250 Clr Delete (Del) 5250 Del Duplicate (Dup) 5250 Dup Erase Input (E-Inp) 5250 E-Inp Field Exit (Enter)
Page 351 To get this function Press these keys in this order Result / Notes Display Backlight Blue Right Scan Up Arrow Backlight lighter Lighter Display Backlight Blue Right Scan Down Arrow Backlight darker Darker Alt mode Alt mode Ctl mode Control mode Escape Escape Space...
Page 352 To get this function Press these keys in this order Result / Notes F10 mode Blue F11 mode Blue F12 mode Blue F13 mode Blue F14 mode Blue F15 mode Blue F16 mode Blue F17 mode Blue F18 mode Blue F19 mode Blue F20 mode...
Page 353 To get this function Press these keys in this order Result / Notes SHFT SHFT SHFT SHFT SHFT SHFT SHFT SHFT SHFT SHFT SHFT SHFT SHFT SHFT SHFT SHFT SHFT SHFT SHFT SHFT SHFT SHFT SHFT SHFT SHFT SHFT 10-9...
Page 354 To get this function Press these keys in this order Result / Notes 0 (zero) 0 (zero) . (period) Orange Period . (period) Orange Period Blue Dash or minus sign Reverse Solidus or Blue Backslash Solidus or Forward Orange slash Blue Left square bracket Blue...
Page 355 To get this function Press these keys in this order Result / Notes SHFT 0 (zero) Right parenthesis " Orange Double quote Blue Curly left brace Blue Curly right brace Orange Vertical bar or Pipe Orange Tilde < Blue Less than mark >...
Page 356: Mx9 38-Key Keymap
MX9 38-key Keymap The following keypad keymap is used on an MX9 that is not running a Terminal Emulator. Terminal emulators use a separate keymap. A modifier key pressed after itself toggles that modifier key off. Any key press, other than a modifier key following any modifier key unsticks the modifier keys.
Page 357 To get this function Press these keys in this order Result / Notes Cursor Left Blue Down Arrow Cursor left one space Insert Orange CTRL Insert mode Delete Orange BKSP Delete one character Home Orange SHIFT Down Arrow Home Orange SHIFT Up Arrow Page up...
Page 358 To get this function Press these keys in this order Result / Notes Alpha Alpha Alpha Alpha Alpha Alpha Alpha Alpha Alpha Alpha Alpha Alpha 7777 Alpha Alpha Alpha Alpha Alpha Alpha Alpha 9999 SHFT Alpha SHFT Alpha SHFT Alpha SHFT Alpha SHFT...
Page 359 To get this function Press these keys in this order Result / Notes SHFT Alpha 7777 SHFT Alpha SHFT Alpha SHFT Alpha SHFT Alpha SHFT Alpha SHFT Alpha SHFT Alpha 9999 0 (zero) 0 (zero) . (period) Orange Period Blue Dash or minus sign Reverse Solidus or Blue...
Page 360 To get this function Press these keys in this order Result / Notes Orange Number sign SHFT 3 (number) Number sign Orange Dollar sign SHFT 4 (number) Dollar sign SHFT 5 (number) Percent sign Blue CTRL Caret or circumflex SHFT 6 (number) Caret or circumflex &...
Page 361: Chapter 11 - Technical Specifications
Chapter 11 - Technical Specifications Processor Marvell PXA-320 / 806 MHz Memory 128MB on-board RAM / 128 on-board Flash SD expansion slot for flash memory (128MB / 512MB / 1GB / and 4 GB supported) Expansion slots Internal CF slot for Summit a/b/g radio, protected inside device. Microsoft®...
Page 362: Dimensions And Weight
Dimensions and Weight Dimensions and weights for MX9 configurations. Length (overall) 9.94 in / 25.2 cm Width at Display 3.87 in / 9.8 cm Depth at display/scanner 2.67 in / 6.8 cm Width at keypad 2.94 in / 7.5 cm Depth at keypad 1.78 in / 4.5 cm...
Page 363: Main Battery Technical Specifications
For 5 GHz frequency band, the site survey limit is -65 dBm signal strength, 15 dB SNR as measured by Honeywell. The noise levels for each of the radios (as measured by the MX9 appropriate antenna) is less than or equal to the values...
Page 364: Bluetooth System Compatibility
Backward compatibility with Bluetooth 1.1 and 1.2 WAN Radio Note: Only one radio at a time can be in an MX9. The MX9 provides an 802.11a/b/g WAN radio and supports GSM/EDGE. Carriers are AT&T in the US (GSM) and RTTE Europe.
Page 365: Ac/Dc Wall Adapter
AC/DC Wall Adapter The AC/DC Power Adapter is only intended for use in a 25°C (77°F) maximum ambient temperature environment. Input Power Switch None Power "ON" Indicator Input Fusing Thermal Fuse Input Voltage 100 VAC min – 240 VAC max Input Frequency 50 - 60 Hz Input Connector...
Page 366: Gps Receiver Technical Specifications
GPS Receiver Technical Specifications The GPS receiver COM port is turned off by default. The COM port is 5, defaults are 9600 baud, 8 bits, no parity, 1 stop bit. COM5 default baud rate is 4800 for NMEA communication. GPS COM settings are stored in the registry. Frequency Band Channel bandwidth is 2 MHz.
Page 367: Chapter 12 - Technical Assistance
Limited Warranty Honeywell International Inc. ("HII") warrants its products to be free from defects in materials and workmanship and to conform to HII’s published specifications applicable to the products purchased at the time of shipment. This warranty does not cover any HII product which is (i) improperly installed or used;...
Page 368 The duration of the limited warranty for the MX9 Battery Charger is 1 year. The duration of the limited warranty for the MX9 2400mAh Li-Ion and 2100mAh Li-Ion Battery is 6 months. The duration of the limited warranty for the MX9 AC power supply and cables is 1 year.
Page 369 12-3...
Page 370 Honeywell Scanning & Mobility 9680 Old Bailes Road Fort Mill, SC 29707 www.honeywellaidc.com E-EQ-MX9WMRG Rev D 1/13...

Honeywell MX9 Reference Manual

Chapter 1 - Introduction

Chapter 2 - Hardware

Chapter 3 - Power

Chapter 4 - Software

Chapter 5 - Using Activesync

Chapter 6 - Data Collection

Quick Links

Related Manuals for Honeywell MX9

Summary of Contents for Honeywell MX9