Table of Contents
Advertisement
Quick Links
RETURN TO MAIN MENU
IM827-D
February, 2011
POWER FEED
10M WIRE FEEDER
™
11086, 11193, 11216, 11439, 11771, 11772
For use with machines having Code Numbers:
Safety Depends on You
Lincoln arc welding and cutting
equipment is designed and built
with safety in mind. However,
your overall safety can be
increased by proper installation
... and thoughtful operation on
your part. DO NOT INSTALL,
OPERATE OR REPAIR THIS
EQUIPMENT WITHOUT READ-
ING THIS MANUAL AND THE
SAFETY PRECAUTIONS CON-
TAINED THROUGHOUT. And,
most importantly, think before
you act and be careful.
OPERATOR'S MANUAL
Copyright © Lincoln Global Inc.
• World's Leader in Welding and Cutting Products •
• Sales and Service through Subsidiaries and Distributors Worldwide •
Cleveland, Ohio 44117-1199 U.S.A. TEL: 1.888.935.3877 FAX: 216.486.1751 WEB SITE: www.lincolnelectric.com
Advertisement
Table of Contents
Related Manuals for Lincoln Electric POWERFEED IM827-D
Summary of Contents for Lincoln Electric POWERFEED IM827-D
- Page 1 RETURN TO MAIN MENU IM827-D February, 2011 POWER FEED 10M WIRE FEEDER ™ 11086, 11193, 11216, 11439, 11771, 11772 For use with machines having Code Numbers: Safety Depends on You Lincoln arc welding and cutting equipment is designed and built with safety in mind.
-
Page 2: California Proposition 65 Warnings
351040, Miami, Florida 33135 or CSA Standard W117.2-1974. A Free copy of “Arc Welding Safety” booklet E205 is available from the Lincoln Electric Company, 22801 St. Clair Avenue, Cleveland, Ohio 44117-1199. bE SURE THAT ALL INSTALLATION, OPERATION, MAINTENANCE AND REPAIR PROCEDURES ARE PERFORMED ONLY bY QUALIFIED INDIVIDUALS. -
Page 3: Electric Shock Can Kill
ELECTRIC SHOCK can kill. 3.a. The electrode and work (or ground) circuits are electrically “hot” when the welder is on. Do not touch these “hot” parts with your bare skin or wet clothing. Wear dry, hole-free gloves to insulate hands. - Page 4 WELDING and CUTTING SPARKS can cause fire or explosion. 6.a. Remove fire hazards from the welding area. If this is not possible, cover them to prevent the welding sparks from starting a fire. Remember that welding materials from welding can easily go through small cracks and openings to adjacent areas.
- Page 5 PRÉCAUTIONS DE SÛRETÉ Pour votre propre protection lire et observer toutes les instructions et les précautions de sûreté specifiques qui parraissent dans ce manuel aussi bien que les précautions de sûreté générales suiv- antes: Sûreté Pour Soudage A L’Arc 1. Protegez-vous contre la secousse électrique: a.
- Page 6 Electric for advice or information about their use of our products. We respond to our customers based on the best information in our posses- sion at that time. Lincoln Electric is not in a position to warrant or guarantee such advice, and assumes no liability, with respect to such infor- mation or advice.
-
Page 7: Table Of Contents
–––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––– Installation...Section A Technical Specifications ...A-1 Safety Precautions ...A-2 Location...A-2 Mounting ...A-2 Safety Precautions ...A-3 Weld Cable Sizing ...A-3 Weld Cable Connection ...A-3 Weld Cable Sizes ...A-3 Electrode Lead ...A-3 Coaxial Weld Cables ...A-4 Changing Electrode Polarity ...A-4 Negative Electrode Polarity ...A-4 Control Cable ...A-5 Control Cable Connection ...A-5 Control Cable Specifications ...A-5... - Page 8 Operation...Section b Aluminum Synergic GMAW-P (Pulsed MIG) and GMAW-PP (Pulse on Pulse) Welding ...B-21 Machine Functionality by Weld Process ...B-22/B-27 CC-Stick ...B-22 CV GMAW/FCAW (NON-SYNERGIC)...B-23 GMAW (SYNERGIC) ...B-24 Pulse and Pulse-on-Pulse (SYNERGIC)...B-25 STT and STT II (SYNERGIC) ...B-26 GTAW (TIG) Welding ...B-27 User Memories ...B-28 Dip Switch Settings ...B-28 6.
-
Page 9: Installation
TECHNICAL SPECIFICATIONS : Power Feed™ 10M Single Wire Feeder WIRE DRIVE OR WIRE DRIVE SECTION OF FEEDER SPEC.# TYPE LOW SPEED RATIO Low Speed K2230-1 Bench Model 50-800 IPM K2314-1 Boom Model (1.27-20.3 m/m) CONTROL bOx, WIRE DRIVE AND COMPLETE UNITS SPEC.# TYPE INPUT POWER... -
Page 10: Safety Precautions
SAFETY PRECAUTION ELECTRIC SHOCK can kill. • Only qualified personnel should perform this installation. • Turn off the input power to the power source at the disconnect switch or fuse box before working on this equipment. Turn off the input power to any other equipment connected to the welding system at the disconnect switch or fuse box before working on this equipment. -
Page 11: Safety Precautions
Table A.2 has the copper cable sizes recommended for different currents and duty cycles. Lengths stipu- lated are the distance from the welder to work and back to the welder again. Cable sizes are increased for greater lengths primarily for the purpose of mini- mizing voltage in the welding circuit. -
Page 12: Coaxial Weld Cables
For Electrode Connect the Polarity: Electrode lead to Positive Positive Stud Negative Negative Stud For additional Safety information regarding the elec- trode and work cable set-up, See the standard "SAFE- TY INFORMATION" located in the front of the Instruction Manuals. CAUTION Excessive voltage drops caused by poor work piece connections often result in unsatisfactory... -
Page 13: Control Cable
DIP Switch #7 Position (negative) - polarity (positive) + polarity FIGURE A.3 CONTROL CAbLE CONTROL CAbLE CONNECTIONS • All system control cables are the same. • All control cables can be connected end to end to extend their length. • All system equipment must be connected to a con- trol cable. -
Page 14: Wire Drive Systems
WIRE DRIVE SYSTEMS Drive Roll Kits are designed to feed specific types and wire sizes. The Power Feed™ 10M Single Wire Feeder does not include these Drive Roll Kits with this Wire Drive, but are available for ordering from the fol- lowing tables: Drive Roll Kits, Steel Wires Includes: 4 Smooth V groove drive rolls and an inner... -
Page 15: Drive Roll Pressure Setting
Set the drive roll pressure by: 1. Press the end of the gun against a solid object that is electrically isolated from the welder output and press the gun trigger for several seconds. 2. If the wire "birdnests" or jams, the drive roll pres- sure is too high. -
Page 16: Welding Gun Torch And Accessories
WELDING GUNS, TORCHES AND ACCES- SORIES GUN RECEIVER bUSHING The Power Feed™ 10M Single Wire Feeder comes with a K1500-2 gun receiver bushing, for use with the Magnum gun with a K466-10 connector kit which . The Power Feed™ 10M Single Wire Feeder Push Pull model comes with a S25398 gun receiver bush- ing, for use with the push pull gun. -
Page 17: Wire Feed Shut Down Circuit
WIRE FEED SHUT DOWN CIRCUIT The wire feed shut down circuit is used to stop the wire feed in the event of a fault. The most common use of the circuit is with water cooled guns. A flow sensor is connected to the circuit to protect the weld- ing gun if the water flow is interrupted. -
Page 18: Wire Reel Loading
A-10 CLAMPING COLLAR SCREWS LOW SPEED HIGH SPEED SCREW SETTING SCREW FOR ROTATING FEED PLATE 9. Loosen the two screws on the bottom of the feed plate clamping collar. 10. Rotate the feed plate to the desired position. 11. Tighten the two screws on the bottom of the feed plate clamping collar. - Page 19 A-11 Using K1504-1 Coil Reel 50-60 lb. (22.7 - 27.2 kg) Coil Mounting (See Figure A.10) 1. Make sure the spindle of the wire reel stand is in the upper position. 2. With the coil reel assembly mounted to a 2" (51mm) spindle, loosen the spinner nut and remove the cover plate.
-
Page 20: Weld Wire Routing
A-12 Loading 30 lb. (13.6 kg) Readi-Reels (See Figure A.11) A K363-P Readi-Reel adapter is required for loading these spools on 2" (51mm) spindles. 1. Squeeze the release bar on the retaining collar and remove it from the spindle. 2. Place the Readi-Reel adapter on the spindle, align- ing the spindle brake pin with one of the holes in the adapter. -
Page 21: Shielding Gas Connection
A-13 SHIELDING GAS CONNECTION NOTE: Gas supply pressure must be regulated to a maximum of 80 psi(5.5 bar). Install the shielding gas supply as follows: 1. Secure the cylinder to prevent it from falling. 2. Remove the cylinder cap. Inspect the cylinder valves and regulator for damaged threads, dirt, dust, oil or grease. -
Page 22: Examples Of Connecting An Arclink Power Wave System
The majority will self configure. If an assembled system flashes the sta- tus light green rapidly on all components, contact the Lincoln Electric Company for further assistance. Current Power Feed™ 10M models that will not self configure... -
Page 23: Bench Model Features
A-15 bOOM CONFIGURATION WIRE DRIVE bENCH MODEL FEATURES bASIC Power Feed™ 10M Single Wire Feeder WELDING SYSTEM CONFIGURATION C a b l e W o r k P o w e r S o u r c e S h i e l d i n g E l e c t r o d e C a b l e D i g i t a l C o n t r o l C a b l e D r i v e R o l l... -
Page 24: Operation
• Insulate yourself from the work and ground. • Always wear dry insulating gloves. • Do not use AC welder if your cloth- ing, gloves or work area is damp or if working on, under or inside work- piece. -
Page 25: Definitions Of Welding Modes
DEFINITIONS OF WELDING MODES NON-SYNERGIC WELDING MODES • A Non-synergic welding mode requires all welding process variables to be set by the operator. SYNERGIC WELDING MODES • A Synergic welding mode offers the simplicity of single knob control. The machine will select the cor- rect voltage and amperage based on the wire feed speed (WFS) set by the operator. -
Page 26: Required Equipment
PROCESS LIMITATIONS The Power Feed™ 10M Single Wire Feeder is not suitable for: • SAW • GTAW with HF Not all weld modes or processes described in this manual are avail- able on all Power Wave power sources. REQUIRED EQUIPMENT Lincoln’s Power Feed™... -
Page 27: Front Panel Controls And Connections
FRONT PANEL CONTROLS AND CONNECTIONS CASE FRONT CONTROLS ITEM Status LED indicates system status. Digital Meter Display is a bright LED display of key welding information. Adjusting Parameter Knobs. MSP4 Panel is used to set the weld mode, adjust the arc, change arc start/end parameters and for set- up information. -
Page 28: Status Led
1. STATUS LED The status LED indicates system status. Normal operation is a steady green light. Note: During normal power-up, the LED may flash red and/or green as the equipment performs self tests. LED condition Definition Steady green System okay. The power source and wire feeder are communicating nor- mally. -
Page 29: B. Volts / Trim Display And Output Knob
b. VOLTS / TRIM DISPLAY AND OUTPUT KNOb The voltage/trim meter displays either the voltage or trim value, depending upon the welding process (mode) being used and the status of the wire feeder and power source. Below the meter are the words “Volts” and “Trim”. An LED light illuminates to designate which value is being displayed on the meter. -
Page 30: Overview
OVERVIEW: The MSP4 is the standard mode select panel for the Power Feed™ 10M Single Wire Feeder wire feeders. The MSP4 is capable of: - Weld mode selection. - Arc Control adjustment. - Weld sequence control (Preflow Time, Run-in WFS, etc.) FIGURE B.3 IR PORT PULSE 4043 Ar... -
Page 31: Power-Up Sequence
This allows wireless machine configuration using a Palm OS based hand held computer. A proprietary Palm OS application, Weld Manager, was developed for this pur- pose. (Contact Lincoln Electric for more information on this feature.) LOCKOUT/SECURITY The MSP4 can be optionally configured to prevent the welder from changing selected user interface controls. -
Page 32: Limit Setting
LIMIT SETTING The MSP4 can be optionally configured to limit the operator’s range of control of any weld parameter (weld WFS, arc control, etc.). Limits are only available with the Dual Procedure/Memory Panel. MACHINE SETUP/USER PREFERENCES The MSP4 can be used to configure and troubleshoot the machine. -
Page 33: Setup Features Menu
b-10 The Setup Menu gives access to the Setup Configuration. Stored in the setup configuration are user parameters that generally only need to be set at installation. The parameters are grouped as shown in the following table. PARAMETER P.1 through P.99 P.100 through P.107 SET-UP FEATURES MENU (See Figure B.3a) - Page 34 b-11 Parameter Exit Setup Menu This setup menu parameter can be used to exit the setup menu. When P.0 is displayed, press the left Mode Select button to exit the setup menu. Wire Feed Speed Units P.1 selects which units wire feed speed will be displayed in. English = in/minute wire feed speed units (default).
- Page 35 b-12 Parameter Procedure Change Method Selects how remote procedure selection (A/B) will be made. The selected procedure can be changed locally at the user interface by pressing the 'A-Gun-B' button. The following methods can be used to remotely change the selected procedure: •...
- Page 36 b-13 Parameter Gun Offset Adjustment Range: -30 to 30 (default = 0) Adjusts the wire feed speed calibration of the pull motor of a push-pull gun. This should only be performed when other possible corrections do not solve any push-pull feeding problems. An rpm meter is required to perform the pull gun motor offset calibration.
- Page 37 b-14 Parameter P.16 Push-Pull Gun Knob behavior Determines how the potentiometer on the Push/Pull torch will behave. • Gun Pot Enabled = The welding wire feed speed is always controlled by the potentiometer on the push- pull gun (default). The left front panel knob is only used to adjust Start and Crater wire feed speed. •...
- Page 38 b-15 Parameter P.99 Show Test Modes Most power sources contain weld modes used for calibration and test purposes. By default, the machine does not include test weld modes in the list of weld modes that are available to the operator. To manually select a test weld mode, set this option to "Yes".
-
Page 39: Cold Feed / Gas Purge Switch
b-16 4. COLD FEED / GAS PURGE SWITCH Cold Feed and Gas Purge are combined into a two position momentary toggle switch. To activate Cold Feeding, hold the switch in the UP position. The wire drive will feed electrode but neither the power source nor the gas solenoid will be ener- gized. - Page 40 b-17 2 STEP TRIGGER OPERATION (See Figure B.4) Sometimes it is advantageous to set specific arc start, crater and arc ending parameters for the ideal weld. Many times when welding aluminum crater control is necessary to make a good weld. This is done by set- ting Start, Crater and Burnback functions to desired values.
- Page 41 Start and less heat desired during Crater. With 4 step trigger, the welder chooses the amount of time to weld at the Start, Weld and Crater settings by using the gun trigger. Burnback reduces the likelihood of wire to sticking in the weld pool at the end of a weld and also prepares the end of the wire for the next arc start.
-
Page 42: Process Setup And Operation
b-19 PROCESS SETUP AND OPERATION The Power Feed ™ /Power Wave ® system delivers world class arc performance for a wide variety of processes. Using the foundation of Waveform Control Technology™, each weld mode is precisely tuned to meet exacting standards for low spatter, weld bead profile and arc shape. -
Page 43: Steel And Stainless Synergic Gmaw-P (Pulsed Mig) Welding
b-20 STEEL AND STAINLESS SYNERGIC GMAW-P (PULSED MIG) WELDING Synergic GMAW-P (Pulsed MIG) welding is ideal for low spatter, out of position and reduced heat input applica- tions. During pulse welding, the welding current continuously switches from a low level to a high level and then back again. -
Page 44: Aluminum Synergic Gmaw-P (Pulsed Mig)And Gmaw-Pp (Pulse On Pulse) Welding
b-21 ALUMINUM SYNERGIC GMAW-P (PULSED MIG)AND GMAW-PP (PULSE ON PULSE) WELDING The Power Feed™ 10M Single Wire Feeder and Power Wave welding power source combine to readily produce top quality aluminum welds with excellent appearance, little spatter and good bead shape. Push- pull guns are available for consistent feeding when welding a long distance away from the wire feeder. -
Page 45: Machine Functionality By Weld Process
b-22 MACHINE FUNCTIONALITY bY WELD PROCESS CC-STICK Use the following tables to review how the machine functions (output controls, arc control and weld options) for the weld modes listed in the top table. ARC CONTROL ARC FORCE DESCRIPTION (Soft)-10.0 to Arc Force adjusts the short cir- (Crisp)+10.0 cuit current for a soft arc, or for... -
Page 46: Cv Gmaw/Fcaw (Non-Synergic
b-23 MACHINE FUNCTIONALITY bY WELD PROCESS CV GMAW/FCAW (NON-SYNERGIC) Use the following tables to review how the machine functions (output controls, arc control, Start options and weld options) for the weld modes listed in the top table. OUTPUT CONTROL KNObS, WELD MODE 5 & 6 AMPS LESS MORE... -
Page 47: Gmaw (Synergic
b-24 MACHINE FUNCTIONALITY bY WELD PROCESS GMAW (SYNERGIC) Use the following tables to review how the machine functions (output controls, arc control, Start options and weld options) for the weld modes listed in the top table. MATERIAL Steel Steel Stainless Stainless Aluminum 4043 Aluminum 5356... -
Page 48: Pulse And Pulse-On-Pulse (Synergic
b-25 MACHINE FUNCTIONALITY bY WELD PROCESS PULSE AND PULSE-ON-PULSE (SYNERGIC) Use the following tables to review how the machine functions (output controls, arc control, Start options and weld options) for the weld modes listed in the top table. MATERIAL ALUMINUM 4043 ALUMINUM 4043 ALUMINUM 5356 ALUMINUM 5356... -
Page 49: Stt And Stt Ii (Synergic
b-26 MACHINE FUNCTIONALITY bY WELD PROCESS STT AND STT II (SYNERGIC) Use the following tables to review how the machine functions (output controls, arc control, Start options and weld options) for the weld modes listed in the top table. MATERIAL PROCESS STEEL ... -
Page 50: Gtaw (Tig) Welding
b-27 MACHINE FUNCTIONALITY bY WELD PROCESS GTAW (Touch Start TIG) Welding Use the following tables to review how the machine functions (output controls, arc control, Start options and weld options) for the weld modes listed in the top table. ARC CONTROL No Arc Controls are active for Touch Start TIG. -
Page 51: User Memories
b-28 USER MEMORIES Recall a memory with memory buttons To recall a user a memory, press one of the six user memory buttons. The memory is recalled when the button is released. Do not hold the button for more than two seconds when recalling a user memory. Recall a memory with the gun trigger If desired, memories 2 through 6 can be recalled with the gun trigger. -
Page 52: Limit Settings
b-29 LIMIT SETTING Each user memory can be optionally configured to limit the user’s range of control over some user interface set- tings. By default, user limits are not enabled. To set lim- its for a selected memory, first select a weld mode and perform a memory save. -
Page 53: Accessories
OPTIONAL: K2339-1 K2429-1 ArcLink “T” Cable Connector K2360-1 Dual Procedure/Memory Panel K1543-xx K1796-xx K1842-xx K1500-1 Gun Receiver Bushing (for guns with K466-1 Lincoln gun connec- tors; Innershield and Subarc guns) K1500-2 Gun Receiver Bushing (for guns with K466-2, K466-10 Lincoln gun connectors;... - Page 54 K1500-4 Gun Receiver Bushing (for gun with K466-3 Lincoln gun connec- tors; compatible with Miller® guns.) K1500-5 Gun Receiver Bushing (compatible K489-7 Gun Receiver Bushing (for Lincoln K466-2 Magnum 200/300/400 to K1500-2 K613-7 Magnum 550 to K1500-3 Adapter K1546-1 Incoming Bushing, Lincoln Conduit K1546-2 Incoming Bushing, Lincoln Conduit K1733-1...
- Page 55 K162-1 Spindle Adapter, for Readi-Reels K435 Spindle Adapter, for mounting 14 lb. Innershield Coils on 2" spindles. K468 Spindle Adapter, for mounting 8" K363P Readi-Reel Adapter, for mounting K438 Readi-Reel Adapter, for mounting K1504-1 Coil Adapter, for mounting 50-60 K1634-1 Plastic Wire Cover for 30-44 lb.
-
Page 56: Maintenance
SAFETY PRECAUTIONS WARNING ELECTRIC SHOCK can kill. • Do not touch electrically live parts such as output terminals or internal wiring. • When inching with gun trigger, electrode and drive mechanism are “hot” to work and ground and could remain energized several seconds after the gun trigger is released. -
Page 57: Troubleshooting
HOW TO USE TROUbLESHOOTING GUIDE Service and Repair should only be performed by Lincoln Electric Factory Trained Personnel. Unauthorized repairs performed on this equipment may result in danger to the technician and machine operator and will invalidate your factory warranty. For your safety and to avoid Electrical Shock, please observe all safety notes and precautions detailed throughout this manual. - Page 58 Observe all Safety Guidelines detailed throughout this manual Error Codes for the Power Wave 455: Code 10555 and below Note: For any Err # listed below write down the error number for refference and try cycling power to see if the error clears itself.
- Page 59 Observe all Safety Guidelines detailed throughout this manual Error Codes for the Power Wave 455: Code 10555 and below Note: For any Err # listed below write down the error number for refference and try cycling power to see if the error clears itself.
- Page 60 Observe all Safety Guidelines detailed throughout this manual Error Codes for the Power Wave 455: Code 10675 and above. ERROR CODES FOR THE POWER WAVE 455 The following is a list of possible error codes that the Power Feed 10M Dual Wire Feeder can output via the dis- play on this user interface.
- Page 61 Observe all Safety Guidelines detailed throughout this manual Error Codes for the Power Wave 455: Code 10675 and above. ERROR CODES FOR THE POWER WAVE 455 As a troubleshooter aid, error code information will now persist on the user interface displays even after the fault is cleared.
- Page 62 Observe all Safety Guidelines detailed throughout this manual Error Codes for the Power Wave ® 455: Code 10675 and above. ERROR CODES FOR THE POWER WAVE The following is a list of possible error codes that the Power Feed play on this user interface. Note: For any Err # listed below write down the error number for reference and try cycling power to see if the error clears itself.
- Page 63 Observe all Safety Guidelines detailed throughout this manual Error Codes for the Power Wave 455: Code 10555 and below ® Note: For any Err # listed below write down the error number for refference and try cycling power to see if the error clears itself.
- Page 64 Observe all Safety Guidelines detailed throughout this manual PRObLEMS (SYMPTOMS) LINC-NET SYSTEM ERROR CODES Err 006 Err 100 ARCLINK SYSTEM ERROR CODES Err 31 Primary overcurrent Err 32 Capacitor bank "A" under voltage. If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
- Page 65 Observe all Safety Guidelines detailed throughout this manual PRObLEMS (SYMPTOMS) ARCLINK SYSTEM ERROR CODES Err 33 Capacitor bank "B" under voltage. Err 34 Capacitor bank "A" overvolt- age. Err 35 Capacitor bank "B" overvolt- age. Err 41 Long term secondary over- current.
- Page 66 E-10 Observe all Safety Guidelines detailed throughout this manual PRObLEMS (SYMPTOMS) Err 44 Main CPU problem. Err 53 Voltage sense loss. Err 81 Motor overload, long term. Err 82 Motor overload, short term. Err 95 Spool gun or pull gun motor overload.
- Page 67 E-11 Observe all Safety Guidelines detailed throughout this manual PRObLEMS (SYMPTOMS) The feeder doesn’t power up - no display, no cold feed. No shielding gas. If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
- Page 68 E-12 Observe all Safety Guidelines detailed throughout this manual PRObLEMS (SYMPTOMS) Inconsistent wire feeding or wire not feeding but drive rolls turning. If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
- Page 69 E-13 Observe all Safety Guidelines detailed throughout this manual PRObLEMS (SYMPTOMS) Wire feed speed consistently oper- ates at the wrong value. Variable or "hunting" arc. Poor arc starts with sticking or "blast-offs", weld porosity, narrow and ropy looking bead. If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
- Page 70 DIAGRAMS Enhanced Diagram POWER FEED™ 10M SINGLE WIRE FEEDER...
- Page 71 DIAGRAMS Enhanced Diagram POWER FEED™ 10M SINGLE WIRE FEEDER...
- Page 72 DIMENSION PRINT POWER FEED™ 10M SINGLE WIRE FEEDER...
- Page 75 • World's Leader in Welding and Cutting Products • • Sales and Service through Subsidiaries and Distributors Worldwide • Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB SITE: www.lincolnelectric.com...