Filling Fuel Tank - Ariens 932037 - 724, 932036 - 524, 932504 - 524, 932505 - 724 Owner's/Operator's Manual

Ariens snow blower owner/operator manual
Hide thumbs Also See for 932037 - 724, 932036 - 524, 932504 - 524, 932505 - 724:
Table of Contents

Advertisement

FILLING FUEL TANK

WARNING: AVOID INJURY. Read and
understand the entire Safety section
before proceeding.
Fuel Shut-Off Valve
IMPORTANT: The fuel shut-off valve MUST be
in the closed position prior to transporting the
unit.
The fuel shut-off valve has two positions:
• Closed Position: Use this position to
service, transport, or store the unit.
• Open Position: Use this position to run the
unit.
To add fuel to fuel tank:
1. ALWAYS place unit in open or well-
ventilated area.
2. Stop engine and allow to cool.
3. Clean Fuel Cap and surrounding area to
prevent dirt from entering Fuel Tank.
4. Remove Cap.
IMPORTANT: DO NOT use gasohol or
gasoline containing alcohol. See Engine
Manual for correct type and grade of fuel.
5. Fill fuel tank to within 1/2 in. (1.2 cm)
below bottom of filler neck with unleaded
gasoline.
NOTE: Tank capacity is 2 qt (1.96 L).
6. Replace Fuel Cap and tighten.
7. ALWAYS clean up any spilled fuel.
PRE-START
1. Frozen Impeller
IMPORTANT: Before starting engine, check
impeller to be sure it is not frozen.
To check impeller:
1. With key in "Stop" position, squeeze
Attachment Clutch Bail to Engaged
position.
2. Pull Recoil Starter Handle.
3. If Impeller is frozen, (cannot pull Starter
Handle) move unit to a heated area and
thaw to prevent possible damage.
2. Check Function of Clutches
If clutches do not engage or disengage
properly, adjust or repair before operation (see
Service and Adjustments).
3. Adjust Axle Lock
Use the axle lock pin to lock or unlock the right
wheel. Lock the right wheel to increase
traction; unlock the right wheel to allow for
easier turning of the unit.
4. Adjust Runners
Check and adjust Runners (see Service and
Adjustments). Allow 1/8 in. (3 mm) between
scraper blade and hard, smooth surface(s).
Allow 1-1/4 in. (30 mm) between scraper blade
and uneven or gravel surfaces.
5. Check Engine Fuel & Crankcase Oil
WARNING: AVOID INJURY. Read
and understand the entire Safety
section before proceeding.
Check and add fuel if required. Check that the
engine crankcase oil is full using dipstick.
Refer to Engine Manual for detailed
instructions.
TO STOP IN AN EMERGENCY
Immediately release both control bails to stop
unit in an emergency. Stop engine, remove
key and wait for all rotating parts to stop before
leaving operator's position.
STARTING AND SHUT OFF
WARNING: FAILURE TO FOLLOW
INSTRUCTIONS could result in
personal injury and/or damage to
unit. DO NOT attempt to start your
unit at this time. Read entire Owner/
Operator Manual and the Engine
Manual first.
IMPORTANT: Allow unit and engine to adjust
to the outdoor temperatures before clearing
snow. Before shut-off, run the attachment a
few minutes to prevent freeze-up.
NOTE: Try out each control without the engine
running to see how it works and what it does.
Manual Start
1. Turn discharge chute straight ahead.
2. Make sure that the traction clutch and
attachment drive clutch bails are fully
disengaged.
3. Push Primer Bulb 2 or 3 times for cold
engine.
NOTE: When temperature is below -15˚ F
(-26˚ C) additional priming may be needed.
4. If engine is cold, apply choke. See Engine
Manual for detailed instructions.
NOTE: A warm engine requires less choking
than a cold engine.
5. Set throttle to proper starting position.
6. Insert key into ignition switch and push
into RUN position. DO NOT twist key after
it is inserted.
GB - 16

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents