Operating Instructions - Jensen Multimedia AM/FM/DVD Receiver VM9511TS Instruction Manual

Audiovox multimedia am/fm/dvd receiver instruction manual
Hide thumbs Also See for Multimedia AM/FM/DVD Receiver VM9511TS:
Table of Contents

Advertisement

Available languages

Available languages

VM9511TS

OPERATING INSTRUCTIONS

Power On / Off
Press the
/MUTE button (7) to turn the unit on. The buttons on the
front of the unit light up and "WELCOME" appears briefly in the LCD
panel (23), followed by the current mode status. If the TFT screen is
open, only the current mode status is displayed. You can also turn
on the unit by pressing the OPEN button (1) and opening the TFT
screen.
Press and hold the
/MUTE button (7) on the front panel or the
POWER button (4) on the remote to power off the unit.The monitor
is drawn back into the main compartment and the LCD screen
displays "BYE BYE".
Audible Beep Confirmation
An audible beep tone confirms each function selection. The beep
tone cannot be disabled.
Mute
Press the
/MUTE button (7) on the front panel or the MUTE button
(3) on the remote to mute the volume from the unit. Press the MUTE
button again to restore the volume. "MUTE" is displayed on the LCD
monitor. Adjusting the volume or using any of the audio setup
features cancels the mute function.
Playing Source Selection
Press the SRC button (15) on the front panel or the SRC
button (8) on the remote to change between available playing
sources in the following order: TUNER, DVD, CD Changer,
AUX IN, CAMERA (rear view video camera) and SD. The
playing mode is displayed on the TFT and LCD screens.
AUX IN Mode
An external peripheral device can be connected to this unit
via RCA output and "AUX-IN".
CAMERA Mode
"CAMERA" mode is only available if the camera is connected and
during reverse driving. To install a rear view video camera, connect
the video input cable to the camera output cable.
Volume Adjustment
To increase or decrease the volume level, turn the ROTARY
ENCODER (6) on the front panel or press the VOL+/ VOL- buttons
(15, 16) on remote control. When the volume level reaches "0" or
"40", a beep sounds, indicating that the adjustment limit has been
reached. The volume ranges from "0" to "40". The LCD or TFT
screen displays the volume level for 3 seconds.
Programmable Turn-On Volume
This feature allows the user to select a turn-on volume setting
regardless of the volume setting prior to turning the unit off.
To program a specific volume level, push and hold the VOL/
LO/DX knob (6) while the yellow volume bar is displayed on
the screen. The unit will beep two times to confirm your turn-
on volume setting.
Audio Control Menu
The Audio Control feature allows you to easily adjust your audio
system to meet the acoustical characteristics of your vehicle, which
vary depending on the type of vehicle and its measurements. To get
the best possible sound quality from your new system, be sure to
adjust the settings for the speakers as well. Proper setting of the
Fader and Balance boosts the effects of the cabin equalizer.
Accessing the Audio Control Menu
Press the VOL/LO/DX knob (6) on the front panel once to display
the "AUDIO" menu.
Selecting an Audio Feature for Adjustment
Continuously press the VOL/LO/DX knob (6) on the front panel, or
press the (>>)/(
) buttons (14, 22) on the remote control or the (/\)/
<<
(V) buttons (18, 19) on the joystick to select the audio feature to be
adjusted.
Adjusting an Audio Feature
Rotate the VOL/LO/DX knob (6), press the (|<<)/(>>|) buttons (17,
19) on the remote control, or press the (<)/(>) buttons (16, 17) on the
joystick to adjust the selected feature to the desired setting.
Table 5: Audio Adjustments
Audio Function
Adjustable Range
EQ
User
Flat
Jazz
Pop
Classical
Rock
Vocal
BASS
-14 to +14
TREBL
-14 to +14
SUB
-7 to +7
LOUD
0 (off), 1-4
FAD (Fade)
-9 to +9
BAL
-9 to +9
NOTE: The Bass and Treble levels are only adjustable
when EQ is set to "User" mode.
15
The Loud function compensates for deficiencies in sound ranges at
low levels. Loudness levels range from 1-4 or "off". When the Loud
function is on, "LOUD" is displayed on the screen.
Exiting the Audio Control Menu
Press and hold the VOL/LO/DX knob (6) or stop making
adjustments for a few seconds to exit the audio control menu.
Six-Channel Audio Control
NOTE: Before adjusting the volume of any speaker,
please refer to "Surround Sound" on page 26.
Table 6: 6-Channel Audio Adjustments
Item
Adjustable Range
Master Volume
00 to 40
Front Left Channel Volume
-10 to +10
Front Right Channel Volume
-10 to +10
Rear Left Channel Volume
-10 to +10
Rear Right Channel Volume
-10 to +10
Center Channel Volume
-10 to +10
Subwoofer Volume
-10 to +10
Rear Zone
If a monitor is installed in the rear zone and connected to the
rear zone AV output, passengers in the back seat can control
the DVD output using the rear zone remote control. See
"Multi-Zone Remote Control" on page 12 for instructions.
System Reset
To correct a system halt or other illegal
operation, use the tip of a pen to press the
RESET button (22) located on the front
bottom-right corner of the unit. After a system reset, the unit restores
all factory default settings.
NOTE: If the unit is reset while a DVD is playing, the DVD
resumes play once the reset is complete.
Line Mute
If the "MUTE" wire is connected, audio output mutes when a
telephone call is received by the car phone or when verbal
navigation is performed.
[RESET] Button

Advertisement

Table of Contents
loading

Table of Contents