Brady BBP 33 User Manual
  1. Manuals
  2. Brands
  3. Brady Manuals
  4. Printer
  5. BBP 33
  6. User manual

Brady BBP 33 User Manual

Sign & label printer
Hide thumbs Also See for BBP 33:
Table of Contents

Advertisement

Quick Links

User's Manual

Advertisement

Table of Contents
loading

Related Manuals for Brady BBP 33

Summary of Contents for Brady BBP 33

  • Page 1 User’s Manual...
  • Page 2 This page is intentionally left blank.

  • Page 3: Copyright And Trademarks

    This manual is copyrighted with all rights reserved. No portion of this manual may be copied or reproduced by any means without the prior written consent of Brady. While every precaution has been taken in the preparation of this document, Brady...

  • Page 4: Brady Warranty

    Brady warrants to the buyer that its products are free from defects in material and workmanship, but limits its obligation under this warranty to replacement of the product shown to Brady’s satisfaction to have been defective at the time Brady...

  • Page 5: Bbp ® 33 Agency Compliance And Approvals

    Operation of this equipment in a residential area is likely to cause interference, in which case required corrective measures will be at the owner’s expense. The user is cautioned that any changes or modifications not expressly approved by Brady Worldwide, Inc. could void the user’s authority to use the equipment. Canada...

  • Page 6: Brady Network Card Compliance And Approvals

    Brady Network Card Compliance and Approvals Cumplimiento normativo y seguridad Brady Network Card Compliance and Approvals Warranty 1 year from the date of purchase. Terms and conditions apply. Refer the printer manual for more details. Garantía 1 año a partir el día de la compra. Se aplican términos y condiciones. Consulte el manual de la impresora para obtener más detalles.

  • Page 7: Safety Notices

    Brady Network Card Compliance and Approvals Indicaciones de seguridad Safety Notices • Do not use this product near water, for example, in a wet basement or near a swimming pool. • Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning.

  • Page 8: Fcc Radiation Exposure Statement

    Brady Network Card Compliance and Approvals Indicaciones de seguridad FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

  • Page 9: Declaration Of Conformity

    Brady Network Card Compliance and Approvals Declaration of Conformity Aviso de clase B de la FCC Note : Este equipamiento ha sido probado y cumple con los límites de un dispositivo digital Clase B, conforme a la Parte 15 de las reglas FCC. Estos límites están designados para proporcionar una protección razonable contra la interferencia perjudicial en una instalación...

  • Page 10: Important Note

    Brady Network Card Compliance and Approvals Declaration of Conformity Canada ICES-003 Class B Notice This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
  • Page 11 Brady Network Card Compliance and Approvals Declaration of Conformity Wireless Disclaimer The maximum performance for wireless is derived from Bluetooth 2.0 specifications. Actual performance can vary, including lower wireless network capacity, data throughput rate, range and coverage. Performance depends on many factors, conditions and variables, including...

  • Page 12: Eu Declaration Of Conformity

    Brady Network Card Compliance and Approvals EU Declaration of Conformity EU Declaration of Conformity Europe – EU Declaration of Conformity This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test methods have been applied in order to prove presumption of conformity with the essential requirements of the R&TTE Directive 1999/5/EC:...
  • Page 13 Brady Network Card Compliance and Approvals EU Declaration of Conformity FR - Français Par la présente [nom du fabricant] déclare que l'appareil [type d'appareil] est [French] conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE. Íslenska Þetta tæki er samkvæmt grunnkröfum og öðrum viðeigandi ákvæðum Tilskipunar...
  • Page 14 Brady Network Card Compliance and Approvals National Restrictions National Restrictions This product may be used in all EU countries (and other countries following the EU directive 1999/5/EC) without any limitation except for the countries mentioned below: Ce produit peut être utilisé dans tous les pays de l’UE (et dans tous les pays ayant transposés la directive 1999/5/CE) sans aucune limitation, excepté...
  • Page 15 Brady Network Card Compliance and Approvals Waste Electrical and Electronic Equipment Directive Waste Electrical and Electronic Equipment Directive In accordance with the European WEEE Directive, this device needs to be recycled in accordance with local regulations. English - Environmental Information for Customers in the European Union European Directive 2002/96/EC requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste.
  • Page 16 Brady Network Card Compliance and Approvals Waste Electrical and Electronic Equipment Directive Dansk (Danish) - Miljøinformation for kunder i EU EU-direktiv 2002/96/EF kræver, at udstyr der bærer dette symbol på produktet og/eller emballagen ikke må bortskaffes som usorteret kommunalt affald. Symbolet betyder, at dette produkt skal bortskaffes adskilt fra det almindelige husholdningsaffald.
  • Page 17 Brady Network Card Compliance and Approvals Waste Electrical and Electronic Equipment Directive Ελληνικά (Greek) - Στοιχεία περιβαλλοντικής προστασίας για πελάτες εντός της Ευρωπαϊκής Ένωσης Σύμφωνα με την Κοινοτική Οδηγία 2002/96/EC, ο εξοπλισμός που φέρει αυτό το σύμβολο στο προϊόν ή/και τη συσκευασία του δεν πρέπει να απορρίπτεται μαζί με τα μη διαχωρισμένα αστικά...
  • Page 18 Brady Network Card Compliance and Approvals Waste Electrical and Electronic Equipment Directive Lietuvškai (Lithuanian) - Aplinkosaugos informacija, skirta Europos Sąjungos vartotojams Europos direktyva 2002/96/EC numato, kad įrangos, kuri ir kurios pakuotė yra pažymėta šiuo simboliu (įveskite simbolį), negalima šalinti kartu su nerūšiuotomis komunalinėmis atliekomis. Šis simbolis rodo, kad gaminį...
  • Page 19 Brady Network Card Compliance and Approvals Waste Electrical and Electronic Equipment Directive Polski (Polish) - Informacja dla klientów w Unii Europejskiej o przepisach dotyczących ochrony środowiska Dyrektywa Europejska 2002/96/EC wymaga, aby sprzęt oznaczony symbolem znajdującym się na produkcie i/lub jego opakowaniu nie był wyrzucany razem z innymi niesortowanymi odpadami komunalnymi.

  • Page 20: Copyright Notice

    Copyright (C) 1993, 1994, 1995, 1996, 1997, 1998, 1999,2000, 2001, 2002, 2003, 2004, 2005, 2006 by Larry Wall and others Open Source Licensing Information The Brady Network Card contains open source software licensed under Version 2 of the GNU General Public License. http://www.bradyid.com/opensource To view the license acreement, go to ®...

  • Page 21: Safety And Environment

    Safety and Environment Precautions Safety and Environment ® Please read and understand this manual before using the BBP 33 Sign & Label Printer for the first time. This manual describes all of the main functions of the printer. Precautions Before using the printer, please note the following precautions: •...

  • Page 22: Technical Support And Registration

    Technical Support and Registration Repair and Return Technical Support and Registration Contact Information For repair or technical assistance, locate your regional Brady Technical Support office by going to: • United States: www.bradyid.com • Europe: www.bradyeurope.com • Asia Pacific: www.bradycorp.com •...

  • Page 23: Overview

    Overview Keypad and Button Actions Overview About this Document The purpose of this guide is to provide information and instructions on using the ® 33 Sign & Label Printer. Conventions When using this document, it is important that you understand the conventions used throughout the manual.
  • Page 24 Overview Keypad and Button Actions This page is intentionally left blank. ® xxiv 33 Sign & Label Printer User’s Manual...

  • Page 25: Table Of Contents

    Contents Copyright and Trademarks ..................iii Brady Warranty ......................iv ® 33 Agency Compliance and Approvals............v Brady Network Card Compliance and Approvals ...........vi Safety and Environment..................xxxi Technical Support and Registration ..............xxii Overview .........................xxiii 1 - Introduction Features and Functions ..................1-1 Compatible Applications..................1-2 System Specifications....................
  • Page 26 Troubleshooting Brady Network Card ............. 2-47 Ethernet Connection Failed ............... 2-47 WiFi Connection Failed ................2-48 USB Connection Failed ................2-50 Brady Network Card Configuration Utility ............2-51 General Settings..................2-51 Network Settings ..................2-52 WiFi Settings ..................... 2-53 Bluetooth Settings ..................2-55 Name ....................
  • Page 27 Diagnostics......................3-17 Enter Diagnostic Mode ..................3-17 Sensors ......................3-17 Print Engine Base (PEB) Settings ............. 3-17 Sensor Conditions ..................3-18 Analog Readings ..................3-19 Copy Error Logs ....................3-20 Printer Error Log..................3-20 Script Error Log ..................3-20 USB Test ......................3-21 USB Flash Drive Test................

  • Page 28: Introduction

    This compact, easy-to-operate thermal transfer printer is a stand-alone that easily connects to your computer for printing labels that you produce using LABELMARK™, labeling software. Media and ribbons from Brady Corporation are programmed to work specifically with the printer.

  • Page 29: Compatible Applications

    Compatible Applications Compatible Applications ® The BBP 33 Sign & Label Printer is compatible with the following software applications: • LABELMARK™ Label Design Software • MARKWARE™ Tape and Label Software When used with one of these software packages, the printer will automatically recognize all enabled and compatible media.

  • Page 30: Keypad And Menu Functions

    Keypad and Menu Functions User Interface Keypad and Menu Functions The following describes the keys, buttons and display screen that are used to ® navigate through and use the BBP 33 Sign & Label Printer system. User Interface The user interface (UI) contains the keypad and buttons for using the printer. The main functions are as follows: Item # Icon...

  • Page 31: Display Screen

    Keypad and Menu Functions Display Screen Display Screen The display screen has two modes: • Ready Mode: Indicates printer status and displays estimated remaining media and estimated remaining ribbon. Also indicates the media and ribbon installed. • Menu Selection Mode: Lets you configure system defaults, view and set printer information, perform input and output operations and perform diagnostics.

  • Page 32: Menu Selection Mode

    Keypad and Menu Functions Display Screen Menu Selection Mode The table describes the main options of the display screen when in menu selection mode. See “User Interface Menu Structure” on page 1-6 for a list of all the menu options. Menu Item Description Auto cutter only: Used to automatically cut the media.

  • Page 33: User Interface Menu Structure

    Keypad and Menu Functions Display Screen User Interface Menu Structure ® 33 Sign & Label Printer User’s Manual...

  • Page 34: Printer Set Up

    Printer Set Up Unpack and Set up Printer Carefully unpack and inspect the printer surfaces (interior and exterior) and the labeling system for possible damage during shipping. Note: Be sure to remove any transportation protection from around the printhead and inside the enclosure cover.

  • Page 35: System Components

    Label Exit/Tearoff Bar or Auto Cutter* Media Guides Media Ribbon Cartridge Ribbon Cover Ribbon Cartridge Latch Brady Network Card Expansion Ports 10 Media Wiper 11 Power Button 12 Media Bridge* 13 Ribbon Cover Latch *See User’s Manual for component descriptions.

  • Page 36: Set Up The Printer

    Unpack and Set up Printer Set up the Printer Set up the Printer Connect Printer Power To setup the printer: 1. Plug the power cord [1] into the printer at the location shown. 2. Plug the other end of the power cord into an AC power outlet. The printer automatically turns on and displays the printer status and the size and color of the currently installed media.

  • Page 37: Install Or Change Supplies

    Unpack and Set up Printer Set up the Printer Install or Change Supplies The media and ribbon supply cartridges use a “smart cell” to define and track the supply information. The system automatically recognizes the supply information for the installed media and ribbon. Note: The printer can be either on or off when changing supplies.
  • Page 38 Unpack and Set up Printer Set up the Printer 4. Place ribbon cartridge with ribbon over print head [4] and the product label toward machine, then snap into place. 5. Close and latch the ribbon cover. 6. Close the enclosure cover. 7.
  • Page 39 Unpack and Set up Printer Set up the Printer To install or change media: 1. Open the enclosure cover. 2. Release the latch on the ribbon cover [2] and swing open. ® 33 Sign & Label Printer User’s Manual...
  • Page 40 Unpack and Set up Printer Set up the Printer 3. If engaged, swing yellow media wiper [3] to the back. 4. Slide yellow media guides [4] to full-open. 5. Remove existing media, if installed, by pulling cartridge from printer. 6. Insert media cartridge until spindle ends rest in slots of media holder [6]. Media unwinds from the top of the roll and the smart cell should be on the left side of the spindle.
  • Page 41 Unpack and Set up Printer Set up the Printer Note: When sleeve material is used, the tearbar should be released so the material does not catch on the tearbar when the material is retracted. 11. If sleeve material is installed, release the tearbar by moving the two release tabs [11], one each side, toward the outer edge.

  • Page 42: Feeding And Cutting Label Stock

    Unpack and Set up Printer Feeding and Cutting Label Stock Feeding and Cutting Label Stock Use this procedure to advance the media to the cut position, and (optionally) tear or cut the media. Note: For die-cut media, the media is advanced to the cut position which is the next die-cut label.

  • Page 43: Print Two-Sided Sleeve Material

    Print Two-sided Sleeve Material Feeding and Cutting Label Stock Print Two-sided Sleeve Material When printing two-sided sleeve material, side one is loaded and printed directly from the roll. To print side two, the material is cut at the end of the job, then loaded from the back of the printer.
  • Page 44 Print Two-sided Sleeve Material Feeding and Cutting Label Stock Note: Make sure you place the edge for the starting (1st) label into the printer first. 7. From the back of the printer, feed the edge of the marker through the slot between the enclosure cover and the printer as follows: •...

  • Page 45: System Power

    System Power Rebooting the Printer System Power These procedures describe how to power-up the printer when starting from a non- powered state (i.e., printer has been unplugged) and how to remove power from the printer. Note: With power removed (i.e., printer disconnected from power source), the system clock retains its settings for about 30 days.

  • Page 46: Connect Printer To A Pc Via Usb

    Connect Printer to a PC via USB Rebooting the Printer Connect Printer to a PC via USB ® To use your PC with the BBP 33 Sign & Label Printer, you must have the USB device driver installed on your PC. Note: See “Compatible Applications”...

  • Page 47: Brady Network Cards

    Brady Network Cards Supported Networks Brady Network Cards Supported LED Light Networks LED Light The changing colors of the LED light on the Brady Network Card signifies the following: Color Status Solid Green Card is functioning normally, status is OK. Blinking Orange The firmware is corrupted and it needs to be upgraded.

  • Page 48: Installing A Brady Network Card

    Installing a Brady Network Card Installing a Brady Network Card If your Brady printer is equipped with a Brady Network Card (WiFi or Ethernet), you can configure the printer to run as a local printer (physically attached to your PC via a USB cable) and as a network (shared) printer through Ethernet or WiFi.
  • Page 49 Brady Network Cards Installing a Brady Network Card Install WiFi (first time) Use this installation process to configure your Brady Network Card (BNC) for WiFi printing and install the printer driver for your Brady printer: • If you have just purchased the printer and are setting it up for the first time.
  • Page 50 Installing a Brady Network Card 6. Click First time install for network driver (default), then click Next. 7. Check that your printer is powered on and that the Brady Network Card LED is solid green. 8. Connect the printer to your PC with a USB cable.
  • Page 51 Brady Network Cards Installing a Brady Network Card 9. If the Found New Hardware Wizard displays, continue with the next step, otherwise skip to Step 14. 10. Click the radio button Yes, now and every time I connect a device, then click Next.
  • Page 52 Brady Network Cards Installing a Brady Network Card 12. When completed, click Finish to close the wizard, then click Next. 13. The networks supported by your Brady Network Card are shown. To activate WiFi, click Wireless, then click Next. ®...
  • Page 53 Brady Network Cards Installing a Brady Network Card 14. In the Printer Description field, enter an easy-to-identify name/description for this network connection. You can use any alphanumeric characters. 15. In the Network Address Type field, choose DHCP protocol (default). Note: If you choose Static, you must enter the IP Address, Subnet Mask and Default Gateway fields.
  • Page 54 Brady Network Cards Installing a Brady Network Card 18. Choose the network that your PC is currently connected to, then click Next. Note: If you do not see your network in the list, you can choose Other to manually specify a network.
  • Page 55 Click Next. Note: The Bonjour program is designed to establish and monitor network printers. The Bonjour Printer Wizard establishes your Brady printer as a network printer. 21. Read the Apple End User License Agreement then click I accept the terms in the license agreement.
  • Page 56 Note: For easier identification, the name or description you assigned in Step 14. displays in the lower left corner of the screen. 24. In the Manufacturer field, click Brady (the manufacturers are listed in alphabetical order). 25. In the Model field, click the printer to install, then click Next.
  • Page 57 Brady Network Cards Installing a Brady Network Card 26. When the Bonjour Printer wizard completes, click Finish. 27. The Brady Printer Installation is completed. Click Finish to exit the wizard. ® 33 Sign & Label Printer User’s Manual...
  • Page 58 PC using Ethernet or over a LAN network. Note: The Brady Network Card is configured to support either Ethernet or WiFi connections. You cannot have both connections active at the same time.
  • Page 59 Brady Network Cards Installing a Brady Network Card 5. If your printer and PC are still connected with a USB cable, disconnect it now, then click Next. 6. Click First time install for network driver (default), then click Next. ®...
  • Page 60 Brady Network Cards Installing a Brady Network Card 7. Verify that your printer printer is powered on and the Brady Network Card LED is solid green. 8. Connect the printer to your PC with a USB cable. 9. If the Found New Hardware Wizard displays, continue with the next step, otherwise skip to Step 16.
  • Page 61 Brady Network Cards Installing a Brady Network Card 11. Click the radio button Install software automatically (Recommended), then click Next. 12. When the installation is complete, click Finish to close the wizard, then click Next. ® 33 Sign & Label Printer User’s Manual...
  • Page 62 Brady Network Cards Installing a Brady Network Card 13. Click the radio button for Ethernet, then click Next. 14. In the Printer Description field, enter an easy-to-identify name/description for this network connection. You can use any alphanumeric characters. 15. In the Network Address Type field, choose the default DHCP protocol.
  • Page 63 Brady Network Cards Installing a Brady Network Card 17. Verify that your printer and PC are connected to the same network, then click Next. Note: To verify that your printer and PC are on the same network, see the connection guidelines shown below.
  • Page 64 Click Next. Note: The Bonjour program is designed to establish and monitor network printers. The Bonjour Printer Wizard establishes your Brady printer as a network printer. 19. Read the Apple End User License Agreement, then click I accept the terms in the license agreement and click Next to continue.
  • Page 65 Note: For easier identification, the name or description you assigned in Step 14. displays in the lower left corner of the screen. 21. In the Manufacturer field, click Brady (the manufacturers are listed in alphabetical order). 22. In the Model field, click the printer to install, then click Next.
  • Page 66 Brady Network Cards Installing a Brady Network Card 23. When the Bonjour Printer wizard completes, click Finish. 24. When the Brady Printer Installation is completed click Finish to exit the wizard. ® 33 Sign & Label Printer User’s Manual...
  • Page 67 Note: Your additional PC must be on the same network as the printer. If not, it will not be detected during installation. Once the Brady Network Card has been configured for Ethernet or WiFi, you can install those network drivers on additional PC’s.
  • Page 68 Brady Network Cards Installing a Brady Network Card 4. Verify that the printer is powered on and the Brady Network Card is functioning properly (green light is on), then click Next. The Bonjour wizard lauches automatically. Note: The Bonjour program is designed to establish and monitor network printers.
  • Page 69 Brady Network Cards Installing a Brady Network Card 6. Read the Apple End User License Agreement, then click I accept the terms in the license agreement. 7. Click Next to continue. 8. Click the assigned network printer name. Note: For easier identification, the name or description you assigned previously displays in the lower left corner of the screen.
  • Page 70 10. In the Manufacturer field, click Brady (the manufacturers are listed in alphabetical order). 11. In the Model field, click the printer to install, then click Next. 12. If Brady cannot be found in the Manufacturer field, click Have Disk. ® 33 Sign & Label Printer User’s Manual...
  • Page 71 .inf file for installing a BBP33 printer. Example 14. When the Bonjour Printer wizard completes, click Finish. 15. When the Brady Printer Installation is completed, click Finish to exit the wizard. ® 33 Sign & Label Printer User’s Manual...
  • Page 72 Use this installation process if you intend to send print jobs to the printer from a PC using USB cable only. This procedure installs the printer driver for your Brady printer and installs the Brady Network Card (BNC) configuration utility.
  • Page 73 Brady Network Cards Installing a Brady Network Card 5. If your printer and PC are still connected with a USB cable, disconnect it now, then click Next. 6. Click the radio button to Install USB Driver Only, then click Next.
  • Page 74 Brady Network Cards Installing a Brady Network Card 7. Connect the printer to your PC with a USB cable. 8. If the Found New Hardware Wizard displays, continue with the next step, otherwise skip to Step 10. 9. Click the radio button Yes, now and every time I connect a device, then click Next.
  • Page 75 Brady Network Cards Installing a Brady Network Card 10. Click the radio button Install software automatically (Recommended), then click Next. 11. When the install is complete, click Finish to close the wizard, then click Next. ® 33 Sign & Label Printer User’s Manual...
  • Page 76 Brady Network Cards Installing a Brady Network Card 12. When the Brady Network Card Configuration Utility and USB Driver are successfully installed, click Finish. ® 33 Sign & Label Printer User’s Manual...

  • Page 77: Install Usb Driver

    Establish Adhoc Connection An ad hoc network is a temporary connection between computers and devices used for a specific purpose, such as printing documents from a Brady printer. Ad hoc networks can only be wireless. 1. Open the Brady Network Card Configuration Utility by choosing: Start>Programs>Brady>Brady Network Card>Brady Network Card...
  • Page 78 Brady Network Cards Installing a Brady Network Card 4. Click the radio button Ad-hoc, enter a SSID (network name) and set Channel to Auto (default). 5. Click Connect. The WiFi settings update. ® 33 Sign & Label Printer User’s Manual...

  • Page 79: Install Network Driver

    3. Click Connect. The adhoc connection is established. Install Network Driver To install network drivers, refer to Steps 1 through 13 in “Install Additional PC’s using Brady Network Card Utility” on page 2-34). ® 33 Sign & Label Printer User’s Manual...

  • Page 80: Troubleshooting Brady Network Card

    Brady Network Cards Troubleshooting Brady Network Card Troubleshooting Brady Network Card Ethernet Connection Failed If Ethernet connection fails, an error message displays. The Ethernet connection can fail if the PC and printer are not on the same network. 1. Click Back.

  • Page 81: Wifi Connection Failed

    Brady Network Cards Troubleshooting Brady Network Card WiFi Connection Failed WiFi connection can fail for two reasons: • The PC and printer are not on the same network. • A wrong passkey or security code was entered. PC and Printer not on Same Network 1.
  • Page 82 Brady Network Cards Troubleshooting Brady Network Card Wrong Passkey or Security Mode 1. Click Back. 2. Re-enter the correct passkey. ® 33 Sign & Label Printer User’s Manual...
  • Page 83 Brady Network Cards Troubleshooting Brady Network Card Note: If you selected ‘Other’ in the network list, you need to enter the security mode as well. 3. Click Next to continue with installation. ® 33 Sign & Label Printer User’s Manual...

  • Page 84: Usb Connection Failed

    Brady Network Cards Troubleshooting Brady Network Card USB Connection Failed The USB connection could fail for two reasons: • The printer is powered OFF. • The USB cable is not connected. If the connection fails: 1. Click Back. 2. Power ON the printer and connect the USB cable.

  • Page 85: Brady Network Card Configuration Utility

    Card Configuration Utility. One dialog box iswith multiple tabs is displayed. General Settings On the General Settings tab, the model number of the Brady Network Card is identified and the previously defined connections listed. To change the status of each supported configuration: 1.

  • Page 86: Network Settings

    Brady Network Cards Using Brady Network Card Configuration Utility Network Settings The Network Settings tab displays the unique name you gave to the printer and the Address Type used by it. DHCP is the recommended setting. Note: If Static is selected, you must enter the IP Address, Subnet Mask, and Default Gateway.

  • Page 87: Wifi Settings

    Brady Network Cards Using Brady Network Card Configuration Utility WiFi Settings The WiFi Settings tab displays: • The network type - Infrastructure vs. Adhoc. • The currently connected network. • Security settings for the currently connected network. To setup WiFi settings: 1.

  • Page 88: Name

    Brady Network Cards Using Brady Network Card Configuration Utility 3. If you selected: • A network from the list, enter the network mode or re-enter the network passkey. The SSID (Network Name) field is non-editable. • Other, you can enter a Network Name.

  • Page 89: Firmware Upgrade/Factory Reset

    1. Access the Brady website at www.bradyid.com. 2. Click Customer & Tech Support 3. Under Product & Software Downloads, click the the Brady Network Card firmware upgrade. 4. In the list presented, select the upgrade you want to download, then click BEGIN DOWNLOAD.
  • Page 90 Brady Network Cards Using Brady Network Card Configuration Utility 5. On the File Download screen, click Save. 6. Using standard Windows procedures, determine the directory where you want to save the download data. ® 33 Sign & Label Printer User’s Manual...
  • Page 91 Brady Network Cards Using Brady Network Card Configuration Utility 7. On the Firmware Upgrade tab of the Configuration Utility screen, click Browse. 8. Find the directory in which you saved the download ZIP file, then click Open. 9. On the Firmware Upgrade/Factory Reset tab, click Upgrade. The upgrade program information is automatically installed on your system.

  • Page 92: Factory Reset

    Brady Network Cards Using Brady Network Card Configuration Utility Factory Reset To return all settings to the original Factory settings (defaults): 1. On the Firmware Upgrade/Factory Reset tab of the Configuration Utility, click Reset to Factory Defaults. A warning message displays indicating all previous defined settings will be removed.

  • Page 93: User Interface Menu

    User Interface Menu The User Interface (UI) menu provides feedback and also allows you to access and change printer settings, printer status and tools. A 5-way navigation keypad lets you navigate through the menu structure to choose the option(s) you want. In Ready mode, the UI menu indicates printer status and displays estimated remaining material and ribbon.
  • Page 94 Status Info Status Info Status Info includes information about the printer configuration and fonts. From this menu, you can also print a configuration label, font list or graphics list. To view system information: Note: Press to exit a menu at any time. 1.

  • Page 95: Print Energy

    Output Settings Print Energy Output Settings Output Settings let you set the print energy and print speed. You can also set when you want to tear/cut the label, set mirror printing on or off and change the horizontal and vertical offset. Note: If password protection has been implemented, you will need to enter the password to have access to these functions.

  • Page 96: Print Speed

    Output Settings Tear/Cut Settings Print Speed Print speed lets you adjust the speed setting from 1 to 4 inches per second (ips). Optimal print speed settings are set automatically by the smart cell for the installed media and should only be changed if you are experiencing problems. For example, you can change print speed if you want to print graphics or other densely populated labels more slowly to ensure complete coverage.

  • Page 97: Mirror Print Settings

    Output Settings Offset Mirror Print Settings Use this procedure to print labels suitable for reading in a mirror or through the back of the label. To set the mirror-image option: Note: Mirror print settings are in effect only during the current print job. When the print job is complete, the printer returns to the default setting.

  • Page 98: Language

    Printer Settings Units Printer Settings The Printer Settings menu lets you set the default values for the printer. Defaults are common settings that are pre-assigned to make the system usable as soon as power is applied (e.g., set date and time to your local date and time). By changing the defaults, you can set the printer to your specific requirements.

  • Page 99: Contrast

    Printer Settings Standby Interval Contrast To set the contrast: 1. Press to go to the navigation menu. 2. Press to scroll to Printer Settings, then press 3. Press to scroll to Contrast, then press 4. Press to increase or decrease the contrast setting. Contrast values are between 1 and 20.

  • Page 100: Date & Time

    Connection The printer has three ready modes: • Initializing: The printer is ready, but the connection to the Brady Network Card (BNC) module has not yet been established. • Ready: The printer is fully functional, the BNC module has responded and the printer is ready to print.

  • Page 101: Restore Defaults

    Printer Settings Restore Defaults Restore Defaults Restore Defaults resets the printer to its factory settings. Once selected, it may take a few moments to restore the defaults. 1. Press to go to the navigation menu. 2. Press to scroll to Printer Settings, then press 3.

  • Page 102: Import

    Tools Import Tools Import Import lets you add your own graphics or fonts for use on the printer. Graphics Use this procedure to add your own graphics for use in labels that you create on the printer. Imported graphics must be in one of the following supported format(s) and imported from a USB flash drive.
  • Page 103 Tools Import Fonts Use this procedure to add your own fonts for use in your labels. Only True-Type fonts can be imported. The following True-Type fonts are resident on the printer: • Arial (Normal, Bold, Italic) • Courier New (Normal, Bold, Italic) •...

  • Page 104: Delete

    Tools Delete Delete Use these procedures to delete any of your own graphics or fonts that you previously imported. Note: You cannot delete any of the fonts that come with the printer. Delete Graphics To delete a graphic: 1. Press to go to the navigation menu.

  • Page 105: Password Protection

    Tools Password Protection Password Protection Use this procedure to enable password protection or to change a password. Passwords can be enabled for the Output Settings or Printer Settings menus. Enable Protection To enable password protection: 1. Press to go to the navigation menu. 2.

  • Page 106: Change Password

    Tools Password Protection Change Password When changing the password, be sure to write down the new key combination so that you don’t forget it. To change the password: 1. Press to go to the navigation menu. 2. Press to scroll to Tools, then press 3.

  • Page 107: Upgrade From Pc

    Do not interrupt power on either the printer or PC during the upgrade process. To upgrade: 1. Before installing, verify the following: • Upgrade Utility is available on your PC or via the Brady website (see Technical Support and Registration in this manual for more information). ® •...

  • Page 108: Upgrade From Usb Flash Drive

    Tools Upgrade from USB Flash Drive Upgrade from USB Flash Drive Use this procedure to upgrade the firmware or software from a USB flash drive that contains the upgrade. The system will support only one USB device at a time. To upgrade software from a USB flash drive: CAUTION! Do not interrupt power during an upgrade from a USB flash drive.

  • Page 109: Diagnostics

    Diagnostics Diagnostics Some diagnostics are not available for users. Advanced diagnostics are password protected and to be used only with Brady Technical Support. The password is assigned by Brady. Enter Diagnostic Mode Use this procedure to access any of the diagnostics menus.

  • Page 110: Sensor Conditions

    Tools Diagnostics Sensor Conditions This diagnostic detects the sensor conditions for ribbon motion, door, cutter, leading (edge), diecut, tapeout, wiper, center and tear bar. Conditions are: • BL (blocked) • Clos (closed) or Open • Hom (home position) • Eng (engaged) •...

  • Page 111: Analog Readings

    Tools Diagnostics Analog Readings This diagnostic detects the analog readings for the diecut analog/digital converter, head voltage and thermistor temperature. To view the analog readings: 1. Access Diagnostic mode (see “Enter Diagnostic Mode” on page 3-17). 2. Press to scroll to Analog Readings, then press .

  • Page 112: Copy Error Logs

    Tools Diagnostics Copy Error Logs Printer Error Log 1. Insert a USB drive into any available port on the printer. 2. Access Diagnostic mode (see “Enter Diagnostic Mode” on page 3-17). 3. Press to go to Copy Error Logs, then press 4.

  • Page 113: Usb Test

    Tools Diagnostics USB Test The USB test verifies that the USB ports are active. The tests can be performed with a flash drive or a type-B cable. USB Flash Drive Test To perform a USB test: 1. Access Diagnostic mode (see “Enter Diagnostic Mode” on page 3-17). 2.

  • Page 114: Keyboard Setup

    4. Press repeatedly to exit to the main menu. Advanced Diagnostics A password is required to enter the advanced diagnostic procedures. Contact your Brady Technical Support contact for help with these diagnostics. ® 33 Sign & Label Printer User’s Manual...
  • Page 115 USB Flash Drive Advanced Diagnostics USB Flash Drive Use this procedure to download and print label scripts from a USB device. Label scripts can be created in any of the following programming languages: • BPL (xml) • • jScript • To download a label script: 1.

  • Page 116: Maintenance

    Maintenance Printer Maintenance Removing Power and Media from Printer Before performing any maintenance procedure that involves opening the enclosure cover, you should remove the power and media from the printer. To remove printer power and media: 1. Remove the power plug [1] from the printer. 2.
  • Page 117 Printer Maintenance Removing Power and Media from Printer 3. Release the latch on the ribbon cover [3] and swing open. 4. Release the ribbon cartridge latch [4] and lift the ribbon cartridge up and out. 5. Move yellow media wiper [5] to the back. 6.

  • Page 118: Cleaning The Printer

    Printer Maintenance Cleaning the Printer Cleaning the Printer Remove Dust Dust generated by media cuts can accumulate in the unit. If a significant amount of dust is built up, clean the unit using this procedure. Materials Required • Isopropyl Alcohol •...

  • Page 119: Clean Printer And Keypad Residue

    Printer Maintenance Cleaning the Printer Clean Printer and Keypad Residue Whenever performing any maintenance on the printer, you should also clean any residue caused by the media. Materials Required • Compressed Air Bottle, purchased locally (e.g., HOSA AIR-464 Gear Duster) •...

  • Page 120: Clean Tearbar

    Printer Maintenance Cleaning the Printer Clean Tearbar Note: This procedure is used only for models with a tearbar. Clean the tearbar whenever there are signs of residue or sticky build up. Most of the sticky residue from the tape supply builds up on the underside of the flip-up tearbar.
  • Page 121 Printer Maintenance Cleaning the Printer 5. To lift up the tearbar, move the two yellow tearbar release tabs [5], on each side, toward the outer edge. The tearbar will automatically flip up. ® 6. Using isopropyl alcohol and Kimwipes , clean the underside of the tearbar [6] to remove any built up adhesive.

  • Page 122: Clean Auto-Cutter Blade

    Printer Maintenance Cleaning the Printer Clean Auto-Cutter Blade Note: This procedure is used only for models with an auto-cutter. Note: When cleaning the cutter, you should also clean the media and cutter sensors (see “Clean Sensors” on page 4-9). Materials Required •...
  • Page 123 Printer Maintenance Cleaning the Printer 4. Clean metal cutting blade [4]: a. If the cutting blade shows significant residue, use the adhesive scraping tool from the cleaning kit, or other flat-edged tool, to gently scrape the reside off the cutting blade. b.

  • Page 124: Clean Sensors

    Printer Maintenance Cleaning the Printer Clean Sensors The sensors are located inside the printer and may be covered with dust that results from tearing or cutting the media. The media sensor is located under the yellow media guide. Materials Required •...

  • Page 125: Clean Tape Entrance

    Printer Maintenance Cleaning the Printer Clean Tape Entrance This procedure cleans the tape entrance, exit area and exit chute. The tape entrance can become sticky because of adhesive buildup Note: Clean the exit area after cleaning the sensors (see “Clean Sensors” on page 4-9).
  • Page 126 Printer Maintenance Cleaning the Printer Clean Exit Area (Tearbar only) To clean the exit chute: 1. If necessary, remove power and media from the printer (see “Removing Power and Media from Printer” on page 4-1). 2. Open the enclosure cover. 3.

  • Page 127: Cleaning The Cutter Blade Exit Area (Auto Cutter Only)

    Printer Maintenance Cleaning the Printer Cleaning the Cutter Blade Exit Area (Auto Cutter only) This procedure cleans the cutter blade exit area and the exit chute. Note: You should clean the exit area after cleaning the cutter blade and sensors. The cleaning swab may be damaged when cleaning the exit area.

  • Page 128: Clean Printhead

    Printer Maintenance Cleaning the Printer Clean Printhead Materials Required • Cleaning Kit (Cat # B31-CCT), includes foam swabs, adhesive scraping tool, plastic bottle (not available in all regions) • Isopropyl Alcohol CAUTION! Use only the materials supplied in the cleaning kit. Using other materials may permanently damage the printhead.

  • Page 129: Replacing The Media Wiper

    Printer Maintenance Replacing the Media Wiper Replacing the Media Wiper Materials Required • Media Wiper (5 pack) Kit, Cat #B31-WIPER (sold separately) To replace the media wiper: 1. Remove power and media from the printer (see “Removing Power and Media from Printer”...

  • Page 130: Clearing Jams

    Printer Maintenance Replacing/Adjust Media End Caps Clearing Jams To clear jams from the printer: 1. Remove all damaged ribbon and/or media from the printer. 2. Check that there is no damage to the print head, tear-off bar, sensors, or any other parts.

  • Page 131: Troubleshooting

    Troubleshooting Messages ® The BBP 33 Sign & Label Printer contains error messages that describe what action you should take to resolve any messages or errors. Messages indicate the problem for the task being performed and also provide a possible corrective action.

  • Page 132: Hardware Errors

    Messages Hardware Errors Hardware Errors Problem Cause Corrective Action Printer too warm. Print job The printhead is too hot. The printhead has reached maximum canceled. operating temperature. Allow printer to cool down approximately 10 minutes, Error: 18 then re-initiate the print job. Printer too cold.

  • Page 133: Media Errors

    Messages Ribbon Errors Media Errors Problem Cause Corrective Action Error reading media memory Printer cannot read the media Replace media. If problem persists, cell. Reload or replace media. memory cell: media validation failed contact Technical support. [48]; cannot read media cell [49]; Errors: 48, 49, 50, 51, 52 cannot read memory CRC [50];...

  • Page 134: A - Supported Scripting Languages

    The following tables describe the ZPL, jScript and DPL commands that are supported by ® the BBP 33 Sign & Label Printer. Note: For Brady Print Language (BPL) commands, see the BPL Programmer’s Guide that is included on your Product CD. ZPL Supported Commands Job Control ®...
  • Page 135 ZPL Supported Commands Objects Objects Drawing Objects ® Drawing Objects Descriptions Command Rectangle Circle Diagonal Line Ellipse Download graphic file to printer Text Commands ® Text Description Command Set Text Font (A-Z, 0-9) Set Default Font Assign Character Identifier to Built-in Font ®...
  • Page 136 ZPL Supported Commands Objects Barcodes ® Barcode Descriptions Command ANSI Codabar Aztec 1 Aztec 2 Codablock Code 11 Code 39 Code 49 Code 93 Code 128 Data Matrix EAN/JAN-8 EAN/JAN-13 EAN/UPC Extension Field Default Industrial 2 of 5 Interleaved 2 of 5 Logmars Micro-PDF417 PDF417...
  • Page 137 ZPL Supported Commands Field Data Field Data ® Field Data Descriptions Command Field Data Origin (set upper left corner relative to label home) Field Parameter (set vertical/reverse for font field) Field Reverse Print (white over black or black over white) Field Separator (end of field definition) Field Typeset (sets field position, relative to home) Set field orientation...

  • Page 138: Jscript Supported Commands

    jScript Supported Commands Objects jScript Supported Commands Job Control Job Control Descriptions jScript Start Job End Job (see Number of Labels) Set Label Size (width and length) Measuring Unit (mm, inches, dots) Printer Orientation (degrees) [Label Rotation] Reverse Print Mirror Image Number of Labels / End Job Objects Drawing Objects...

  • Page 139: Printer Status

    jScript Supported Commands Printer Status Barcodes Barcode Descriptions jScript Bar Code Aztec AZTEC Codabar A / F CODABAR Codablock F CODEABLOCKF Code 128 A / B / C CODE128 Code 39 CODE39 Code 93 CODE93 Data Matrix DATAMATRIX EAN-8 EAN8 EAN-13 EAN13 EAN-128...

  • Page 140: Dpl Supported Commands

    DPL Supported Commands Commands DPL Supported Commands Note: These commands conform Revision D, 2001 Datamax Programmer’s Manual Commands Commands Descriptions Set Cut Amount By (Command must be issued and a cut will not occur until job is done.) Set Continuous paper Length <STX>c Input Image Data <STX>I...
  • Page 141 DPL Supported Commands Barcodes Barcodes Barcode Descriptions Barcode Command Structure b [bb] c d eee ffff gggg jj...j where: a = Rotation (1, 2, 3, 4) b [bb] = Barcode c = Wide Bar, (always fixed value of 1)* d = Narrow Bar (1-9)* eee = Symbol Height (001 - 999) ffff = Row (0000 - 9999) gggg = Column...
  • Page 142 DPL Supported Commands Objects Objects Object Descriptions Draw Box 1X1100000970013b0093004200020002 (Parameters bbbb and ssss indicate line thickness of where: box and must be the same.) 1 = Fixed Value 1 = Fixed Value eee = Fixed Value ffff = Row gggg = Column b = Box hhhh = Box Horizontal Width...
  • Page 143 DPL Supported Commands Objects Object Descriptions Draw Line 1X1100000970013L093042 where: 1 = Fixed Value 1 = Fixed Value eee = Fixed Value ffff = Row gggg = Column L = Line Drawing hhhh = Horizontal Width of Line vvvv = Vertical Height of Line Text (font) Only some True Type fonts are supported.
  • Page 144 DPL Supported Commands Objects Object Descriptions Polygon 1 X 11 ppp rrrr cccc P ppp bbbb rrrr cccc rrrr cccc ... <CR> Polygons are created by defining the positions of where corners, specifying a number of data points that 1 = Rotation (must be 1) represent the vertices of the object, which can range 001 = Fixed Value from a simple line (two points), or a triangle (three...
  • Page 145 © 2012 Brady Worldwide, Inc. All Rights Reserved.

Table of Contents