Samsung SRN-470D User Manual
Samsung SRN-470D User Manual

Samsung SRN-470D User Manual

Network video recorder
Hide thumbs Also See for SRN-470D:
Table of Contents

Advertisement

NETWORK VIDEO RECORDER

User Manual

SRN-470D/1670D

Advertisement

Table of Contents
loading

Summary of Contents for Samsung SRN-470D

  • Page 1: User Manual

    NETWORK VIDEO RECORDER User Manual SRN-470D/1670D...
  • Page 2 Disclaimer Samsung Techwin makes the best to verify the integrity and correctness of the contents in this document, but no formal guarantee shall be provided. Use of this document and the subsequent results shall be entirely on the user’s own responsibility. Samsung Techwin reserves the right to change the contents of this document without prior notice.
  • Page 3: Important Safety Instructions

    overview IMPORTANT SAFETY INSTRUCTIONS Read these operating instructions carefully before using the unit. Follow all the safety instructions listed below. Keep these operating instructions handy for future reference. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water.
  • Page 4: Overview

    • SAMSUNG retains the copyright on this manual. • This manual cannot be copied without SAMSUNG's prior written approval. • We are not liable for any or all losses to the product incurred by your use of non-standard product or violation of instructions mentioned in this manual.
  • Page 5 Operating Temperature The guaranteed operating temperature range of this product is 0°C ~ 40°C (32°F ~ 104°F). This product may not work properly if you run right after a long period of storage at a temperature below the guaranteed one. Prior to using a device that has been stored for a long period in low temperatures, allow the product to stand at room temperature for a period.
  • Page 6: Table Of Contents

    overview CONTENTS OVERVIEW Important Safety Instructions Before Start Contents Features Part Names and Functions (Front) Part Names and Functions (Rear) Remote Control INSTALLATION Checking the installation environment Rack Installation HDD Addition CONNECTING WITH OTHER DEVICE Connecting to an external device Connecting the USB Connecting External eSATA HDD Connecting the Alarm Input/Output...
  • Page 7 Search SEARCH & PLAY Playback WEB VIEWER Introducing Web Viewer Connecting Web Viewer Using Live Viewer Using Search Viewer Viewer Setup 109 About BACKUP VIEWER 110 SEC Backup Viewer APPENDIX 113 Product Specification 115 Product Overview 117 Default Setting 120 Troubleshooting 123 Open Source License Report on the Product English _7...
  • Page 8 FEATURES The product records video and audio from network cameras to a hard disk, and enables playback from the hard disk. It also provides remote monitoring environment for video and audio over the network using a remote computer. • User-friendly UI •...
  • Page 9: Package Contents

    Please unwrap the product, and place the product on a flat place or in the place to be installed. Please check the following contents are included in addition to the main unit. SRN-470D NETWORK VIDEO RECORDER SRN-470D ALARM NETWORK BACKUP...
  • Page 10 overview SRN-1670D ALARM ALARM NETWORK NETWORK BACKUP BACKUP DVD RECORDER NETWORK VIDEO RECORDER SRN-1670D DVD RECORDER OPEN/CLOSE OPEN/CLOSE NETWORK VIDEO RECORDER SRN - 1670D Remote Control / Mouse Remote Control Battery (AAA) Network Viewer Software / Power Cable User Manual User Manual CD Quick Guide SATA Cable...
  • Page 11: Part Names And Functions (Front)

    PART NAMES AND FUNCTIONS (FRONT) SRN-470D NETWORK VIDEO RECORDER SRN-470D ALARM NETWORK BACKUP DVD- DVD RECORDER SRN-1670D ALARM ALARM NETWORK NETWORK BACKUP BACKUP DVD RECORDER NETWORK VIDEO RECORDER SRN-1670D DVD RECORDER OPEN/CLOSE OPEN/CLOSE NETWORK VIDEO RECORDER SRN - 1670D Part Names Functions ALARM : Lights on when an event occurs.
  • Page 12: Part Names And Functions (Rear)

    Ports used for external storage device connections. NETWORK 1/2 NETWORK connector port. USB connector port. - ALARM IN : Alarm input ports. SRN-470D : 1~4 CH SRN-1670D : 1~16 CH - ALARM RESET : Alarm Reset port ALARM This is applicable only to SRN-1670D.
  • Page 13: Remote Control

    REMOTE CONTROL SEARCH BACKUP Displays the search menu. Displays the Backup Menu. OPEN/CLOSE Opens or closes the CD tray. MODE Changes the screen mode. DVR/NVR Activates the NVR function. POWER Displays the Exit pop up screen. NUMBER [0~ + 10] Used as the numeric input keys, or displays a single channel.
  • Page 14: Installation

    installation Please take note of the followings before using this product. • Do not use the product outdoor. • Do not spill water or liquid in the connection part of the product. • Do not impose the system to excessive shock or force. •...
  • Page 15: Rack Installation

    Please consult your provider for further information on HDD installation since improper installation or settings may damage the product. Number of HDDs supported : SRN-470D : Up to 1 SRN-1670D : Up to 5 HDDs supported Make sure to unplug the power cord from the wall outlet before proceeding with the installation.
  • Page 16 If installing HDD to SRN-470D 1. First, loosen the screws on both sides and remove the cover. 2. Loosen the left and right screws on the lower hard disk bracket to remove it. 3. Insert the additional hard disk into the bracket and fix it using the provided screws.
  • Page 17 4. Insert the bracket where the additional hard disk is inserted into the lower bracket and fix it using the provided screws. 5. When done, connect the power cable and connect the signal cable (SATA cable) to the connector for the main board.
  • Page 18 installation If installing HDDs to SRN-1670D 1. First, loosen the screws on both sides and remove the cover. Cover 2. Loosen the screws (x4) in the left/right and upper sides and remove the upper brackets. Upper Bracket Lower Bracket 3. Install HDDs (x2) on the lower bracket and fix them with screws.
  • Page 19 5. When the installation of additional HDDs is done, insert the lower and upper brackets into the NVR and fix them with the provided screws. 6. When adding a HDD is completed, plug the power cable and connect the SATA cable (for transferring the HDD signal) to the connector of the main board.
  • Page 20: Connecting With Other Device

    CONNECTING TO AN EXTERNAL DEVICE SRN-470D AUDIO OUT VIDEO OUT Power (VGA) HDMI OUT Adaptor eSATA HDD Mouse SRN-1670D AUDIO OUT VIDEO OUT (VGA) HDMI OUT Power eSATA HDD Mouse Unrated or improper power source may cause damage to the system. Ensure that you use only the rated power source before pressing the POWER button.
  • Page 21: Connecting The Usb

    CONNECTING THE USB 1. By factory default, a USB port is provided for external connection. 2. You can connect a USB HDD, USB CD/DVD player, USB memory or mouse to the USB port. 3. If a USB HDD is connected to the system, recognition and settings are available in "Menu Setup > Device > Storage Device".
  • Page 22: Connecting The Alarm Input/Output

    CONNECTING THE ALARM INPUT/OUTPUT The Alarm In/Out port at the back is composed of the following. SRN-470D Sensors Alarm • ALARM IN 1 ~ 4 : Alarm Input Port • ALARM OUT 1 ~ 2 : Alarm Output Port...
  • Page 23 SRN-1670D Alarm Sensors • ALARM IN 1 ~ 16 : Alarm Input Port • ALARM RESET : On receiving an Alarm Reset signal, the system cancels the current Alarm Input and resumes sensing. • ALARM OUT 1 ~ 4 : Alarm Output Port ALARM OUT ALARM IN ALARM IN...
  • Page 24: Connecting The Network

    connecting with other device CONNECTING THE NETWORK For more information about network connection, refer to "Network Configuration". (Page 72) Network connection via Ethernet (10/100/1000BaseT) Switch Switch Windows Network Viewer Network Camera Network Camera Network connection via router xDSL or Cable Modem NETWORK Brodband router...
  • Page 25: Connecting To Internet Through Adsl

    Connecting to Internet through ADSL NETWORK Phone(ADSL) Line ADSL MODEM Switch Switch Windows Network Viewer Network Camera Network Camera Connecting the network camera Switch Switch Network Camera ex) IP : 192.168.2.10 Network Camera ex) IP : 192.168.2.20 Network Camera ex) IP : 192.168.1.20 Network Camera ex) IP : 192.168.1.10 You can connect the camera or network viewer to either [NETWORK1] or [NETWORK2] to your preference.
  • Page 26: Live

    live GETTING STARTED Starting the system 1. Connect the power cable of the NVR to the wall outlet. 2. Press the Power button on the front panel. 3. You will see the initialization screen. The initialization process will last about 2 minute. If a new HDD is installed, the initialization process may take longer.
  • Page 27: Locking All Buttons

    Login If you want to access a specific NVR menu or restricted menu, you must obtain the applicable permissions to do so. 1. In Live mode, right-click any area, or press [MENU] on the Scene Mode ► remote control. Live Status Record Status You will see the context menu on the screen as shown.
  • Page 28: Live Screen Configuration

    live LIVE SCREEN CONFIGURATION Icons on the Live Screen You can check the status or operation of the NVR with the icons on the live screen. 2012-01-01 00:00:01 CAM 01 Name Description Current Date, Time Displays the current time and date. Login Information When you are logged in, the "LOG ON"...
  • Page 29 Status no video will be displayed but this icon. SRN-470D : If the resolution of a camera video exceeds 1600x1200, the channel of the video source will be shown as HD. For a proper video playback, the connected camera should support a low resolution profile as well.
  • Page 30 live Live Screen Menu Besides the function buttons on the remote control, right-click any area in the Live screen, or press [MENU] on the remote control to display the context menu where you can access a desired menu item. The context menu differs depending on the state of Log in/out, split mode, and NVR operation status. Depending on the user permissions, you may have limited access to menu items of Live View, Backup, Stop Recording, Search, PTZ, Remote Alarm Output, and Exit.
  • Page 31 Split Mode Menu In Live split mode, right-click to display this context menu as shown. The context sensitive menu in split mode differs, depending on the login/logout status. Scene Mode ► Live Status Record Status Audio Off Freeze Stop Alarm Record Play Search...
  • Page 32: View The Launcher Menu

    2. Move the cursor to the bottom and click a desired item in the Launcher menu. If no input is entered for 10 seconds, the menu will disappear. The Launcher menu can be accessed only by using the mouse. SRN-470D supports only: Single mode, 4-split mode, and Auto Sequence. Menu Description Displays the current time and date.
  • Page 33: Live Screen Mode

    LIVE SCREEN MODE You can play up to 16 live video channels in single, 6-split, or auto sequence mode. SRN-470D supports only: Single mode, 4-split mode, and Auto Sequence. NVR Live will request the closest camera profile to each channel size.
  • Page 34: Switching The Split Mode

    live Switching the split mode You can also play 16 Live channels in the sequence of: Single, 4-split and 9-split mode. Auto Sequence 13-16 9-12 10-16 Single mode 4-split mode 9-split mode In Single mode, If you have set <Dwell Time> in "Setting the Device > Camera", Auto Sequence will be conducted at the set interval.
  • Page 35: Channel Setting

    • If pressing the right [►] button in 4-split mode : Channel (CH 1~4) Channel (CH 5~8) Channel (CH 9~12) Channel (CH 13~16) Auto Sequence CH13 CH14 CH10 CH11 CH12 CH15 CH16 13-16 9-12 Channel Setting You can display the channel in a desired area of a split screen. 1.
  • Page 36: Record Status

    live Live Status Select <Live Status> from the live screen menu to display status and transfer information of connected camera to each channel. Record Status Select <Record Status> from the live screen menu to display camera profile, input/recording frame rates, input/limit/recording bps of each channel.
  • Page 37: Zoom

    ZOOM This is activated only in Live Single mode. If you zoom in the screen in Single mode, the selected channel will be enlarged in the original size; if zooming in again, the selected area will be enlarged as twice as the original size. 1.
  • Page 38: Audio On/Off

    live AUDIO ON/OFF You can turn the sound on/off corresponding to the channel in Live mode. AUDIO ON/OFF in Single mode Click the sound icon ( ) on the screen or press [AUDIO] on the remote control to turn on/off the sound. If you have configured the audio output settings properly but the audio or voice is not output, check if the connected network camera supports the sound signal and if you have configured the sound settings as appropriate.
  • Page 39: Event Monitoring

    EVENT MONITORING This will display the channel in sync with a specific event (Sensor/Motion/Video Loss) if it occurs. In "Monitor > Event Display", set the event monitoring to ON/OFF and specify the event display time. (Page 62) • If multiple events occur simultaneously, the screen will switch to a split mode. - 2~4 events : 4-split mode - 5~9 events : 9-split mode - 10~16 events : 16-split mode...
  • Page 40: Ptz Control

    Even if the connected network camera does not support the PTZ operations, you can configure the PTZ control settings (if possible) by installing the PTZ driver (physical device). This is available only with Samsung Techwin-manufactured PTZ network camera. 40_ live...
  • Page 41: Using The Ptz Camera

    Using the PTZ camera You can use a single PTZ camera to perform the Pan, Tilt and Zoom operations to monitor multiple places, and configure the custom settings of the presets in a desired mode. 1. Open the <PTZ Control> menu. The <...
  • Page 42 live Preset Preset is a specific position remembered by the PTZ camera. You can use the Preset function to define up to 127 presets for a single PTZ camera. To add a preset 1. Check the preset checkbox. 2. Select <Add>. The virtual keyboard will appear on the screen.
  • Page 43: Menu Setup

    menu setup You can setup the system properties, devices, and options for recording, event, backup and network. SYSTEM SETUP You can setup Date/Time/Language, Permission, System Properties and Log. Date/Time/Language Setting the Date/Time/Language You can check and setup the current Date/Time and time related properties, as well as the language used for the interface on the screen.
  • Page 44 menu setup Setting Holiday You can set specific dates to Holidays according to your preferences. Holidays are applied to <Recording Schedule> and <Alarm Out Schedule> too. [MENU]  <System Configuration>  ►  <Date/Time/Language>  [ENTER]  ◄►  <Holiday> ...
  • Page 45 Permission Management You can set permissions of each user over the NVR's specific function and settings. Setting the Administrator You can set and change Administrator's ID and password. The administrator can use and set all menu items and functions. [MENU]  <System Configuration>  ►▼  <Permission Management>  [ENTER]  <Admin>  ▲▼◄►...
  • Page 46: Setting The Group

    menu setup Setting the Group You can create user groups and setup permissions for those user groups. You can register a user for each group in <User>. [MENU]  <System Configuration>  ►▼  <Permission Management>  [ENTER]  ◄►  <Group>...
  • Page 47 Setting the users You can add a user and edit information of a registered user. [MENU]  <System Configuration>  ►▼  <Permission Management>  [ENTER]  ◄►  <User>  ▲▼◄►  [ENTER] To register a user 1. Select a user group. You must first register a group where the user will belong to so that user can be registered.
  • Page 48: Setting Permissions

    menu setup Setting Permissions You can set restricted access for all general users. Items with restrictions will require logging in for use. [MENU]  <System Configuration>  ►▼  <Permission Management>  [ENTER]  ◄►  <Setup>  ▲▼◄►  [ENTER] •...
  • Page 49: System Management

    To change the user password If you log in with the user account of a group with restricted access, you just can change your own password. 1. Provide the login information. 2. Select <User Menu>. The Permission Management screen appears. 3.
  • Page 50 menu setup To upgrade the current software version 1. Connect a device storing the software to be updated. It may take about 10 seconds to recognize the device. Upgradeable devices include USB memory, CD/DVD and network device. To update the network, the current NVR should have been connected to the network. Upgrade via the proxy server may not be enabled due to the restricted access.
  • Page 51 Settings You can copy and import the NVR settings by using a storage media. [MENU]  <System Configuration>  ►▼  <System Management>  ▼►  <Settings>  ▲▼◄►  [ENTER] • Storage Device : Shows the connected storage device. •...
  • Page 52: Log Information

    menu setup Log Information You can browse logs on the system and events. Checking the system log System Log shows log and timestamp on every system start up, system shutdown, and changes on system settings. [MENU]  <System Configuration>  ►▼  <Log Information>  [ENTER]  <System Log>  ▲▼◄►...
  • Page 53: Checking The Event Log

    Checking the event log You can search recorded events including alarms, camera events and video loss. It also shows the log and its timestamp. [MENU]  <System Configuration>  ►▼  <Log Information>  [ENTER]  ▼► <Event Log>  ▲▼◄►...
  • Page 54: Setting The Device

    menu setup SETTING THE DEVICE You can setup Camera, Storage Device, Remote Device and Monitor. Camera To register a camera You can register a network camera for each channel and make connection between. [MENU]  ▲▼  <Device>  ►  <Camera>  [ENTER]  ▲▼◄►  [ENTER] •...
  • Page 55 • Model : Select a camera model. - Samsung Network Camera/Encoder : Means the camera/encoder supports Samsung Techwin's SVNP protocol. When connecting a camera that does not appear in the camera list, select Samsung Netowrk Camera/Encoder. However, you must select the correct model name of the camera, if it's in the list. Some of obsolete camera models may not be supported.
  • Page 56 Ex) http://www.samsungipolis.com/snb5000 provide "snb5000" for iPOLiS DDNS - MAC (Samsung) : Available if the camera supports the MAC Address-based DDNS. - URL : Used for URL address input. Refer to the user manual of the connected camera and check the DDNS specification that is supported by the camera.
  • Page 57 • User Model Modification : When registering a new camera, it is named according to the device’s default if user set the model to <Samsung Network Camera/Encoder>. In case if automatic registration fails, user can change the model name of camera to be registered.
  • Page 58: Camera Setting

    menu setup Camera Setting You can change the video settings of a registered network camera for each channel. • Profile : Show a video profile for the connected camera. • Codec : Show the codec information for the selected profile. •...
  • Page 59: Storage Device

    If the channel is set to <Covert1> or <Covert2> mode, the channel’s sound is not hearable. However, the channel’s sound is recorded if its Audio setting is set to <ON>, even the sound is not heard in Live mode. • Audio - If set to <ON>, you can turn the audio of the channel ON/OFF on the Live screen.
  • Page 60 • Alarm - Alarm signal will output through the alarm out port on the rear side when selected <1>, <2>, <3>, and <4>. SRN-470D supports only alarms : <1> and <2>. - If <BEEP> was selected, a beep will sound.
  • Page 61 • Duration : Sets the alarm duration for the alarm signal and beep sound. - Check Alarm, Replace Alarm signals will output through the selected alarm out ports (1, 2, 3, and 4). SRN-470D supports only alarms : <1> and <2>. - If <BEEP> was selected, a beep will sound.
  • Page 62: Monitor Settings

    menu setup Monitor You can set the information displayed on the monitor as well as the output system. Monitor settings You can configure the monitor output-related settings including the displayed information, dwell time and output system. [MENU]  ▼  <Device>  ►▼  <Monitor>  [ENTER]  ▲▼◄►  [ENTER] •...
  • Page 63: Setting The Screen Mode

    To adjust the display position Some monitors many not display information (camera name, icon, time information, etc.) about the NVR, depending on the condition. Then, you can change the display position of the data. 1. From the monitor setup menu, select <Display Position Setup>. 2.
  • Page 64: Setting The Recording

    menu setup SETTING THE RECORDING You can setup scheduled recording, event recording and other recording related settings. Recording Schedule Make your reservation on a date and time to schedule the recording on specified time. [MENU]  ▼  <Record>  ►  <Recording Schedule>  [ENTER]  ▲▼◄►  [ENTER] •...
  • Page 65: Event Record Duration

    Event Record Duration You can set the beginning and ending point of a recording on an event. [MENU]  ▼  <Record>  ►▼  <Event Record Duration>  [ENTER]  ▲▼◄►  [ENTER] • Pre Event : The recording of an event will start at a pre-determined time prior to the actual occurrence of the event. If it is set to 5 seconds, the recording begins from 5 seconds before the event.
  • Page 66 menu setup • Full Frame : Shows the amount of received data for full frame recording. • Key Frame : Shows the amount of received data for key frame recording. • Bitrate Limit : Shows allowed maximum limit of data bitrate, per channel. If a channel's data transfer exceeds defined allowed limit, then it may affect to other channels, and may force switching to <Key Frame>...
  • Page 67: Record Option

    Record Option You can set the recording to stop or overwrite when the HDD is full. [MENU]  ▼  <Record>  ►▼  <Record Option>  [ENTER]  ▲▼◄►  [ENTER] • Disk End Mode : Select a HDD repetitive recording type. - Overwrite : If the HDD is full, this will overwrite the existing data and keep recording.
  • Page 68: Setting The Event

    • Alarm out : Sets the alarm output method. For further information on alarm output, refer to "HDD Alarm > Alarm". (Page 60) SRN-470D supports only alarms <1> and <2>. • Duration : Sets the duration of alarm signal and alarm sound.
  • Page 69: Video Loss Detection

    Camera Event You can set whether to react to camera events (motion detection, video analysis, audio events) and alarm output / time. [MENU]    <Event>  ►  <Camera Event>  [ENTER]  ◄►  [ENTER] • Mode : Select whether to react to camera events or not. •...
  • Page 70: Backup

    menu setup Alarm Out Schedule You can set the conditions and operating hours for scheduled alarms. [MENU]  ▼  <Event>  ►  <Alarm Out Schedule>  [ENTER]  $%_+  [ENTER] • Alarm Out : Sets the alarm output method. For further information on alarm output, refer to "HDD Alarm >...
  • Page 71 • Type : Sets the backup data format. - NVR : Saved data can be played back only by the NVR. - SEC : Saves data in the Samsung's proprietary format with built-in viewer, which supports immediate playback on a PC.
  • Page 72: Network Configuration

    menu setup NETWORK CONFIGURATION It provides networked monitoring of Live screen from a remote place, and supports mail forwarding function with events. You can configure the network environment which enables such functions. Connection Mode You can set the network connection route and protocol. Network 1/Network 2 connection settings Sets the protocol and environment of the network.
  • Page 73: Connecting And Setting The Network

    Connecting and Setting the Network Networking may differ from the connection method, check your environment before setting the connection mode. When no router is used • Static IP mode - Internet connection : Static IP ADSL, leased line, and LAN environments allows connection between the NVR and remote user.
  • Page 74 menu setup When a router is used To avoid IP address conflict with the NVR's static IP, check followings : • Setting the NVR with a static IP - Internet connection : You can connect the NVR to a router which is connected to an ADSL/Cable modem or a router in a Local Area Network (LAN) environment.
  • Page 75: Advanced Setting

    Advanced Setting [MENU]  ▼  <Network>  ►  <Connection Mode>  [ENTER]  ▲▼◄►  <Advanced>  ▲▼◄►  [ENTER] • Protocol Type : Select the protocol type between TCP and UDP. If you select UDP, the items of Port(UDP) and Unicast/Multicast will be active. If set it to TCP, the Port(TCP) item will be active.
  • Page 76 menu setup DDNS You can set the DDNS site for a remote user's network connection. [MENU]  ▼  <Network>  ►▼  <DDNS>  [ENTER]  ▲▼◄► [ENTER] • DDNS Site : Specify the use of DDNS and select a site that you registered. •...
  • Page 77: Ddns Setting

    DDNS Setting DDNS is a short form of Dynamic Domain Naming System. DNS (Domain Name System) is a service that routes a domain name consisting of user friendly characters (ex : www.google.com) to an IP address consisting of numbers (64.233.189.104). DDNS (Dynamic DNS) is a service that registers a domain name and the floating IP address with the DDNS server so that the domain name can be routed to the IP address even if the IP is changed in a dynamic IP system.
  • Page 78: Mailing Service

    menu setup Mailing Service You can send an e-mail to a NVR-registered user at a specific time interval, or if an event occurs. If the camera is set to <OFF> or the channel’s event is Video Loss, a notification is sent to the designated email address only in text.
  • Page 79: Event Setting

    Event Setting You can set the interval and type of the event that will be sent to the user. [MENU]  ▼  <Network>  ►▼  <Mailing Service>  [ENTER]  ▲▼◄►  <Event>  ▲▼◄►  [ENTER] • Event Interval : Set the event interval. If a series of events occurs, the e-mail will be sent at the specified interval, not on each event.
  • Page 80 menu setup Recipient Setting You can add/remove a recipient(s) to/from the specified group and edit the group if necessary. [MENU]  ▼  <Network>  ►▼  <Mailing Service>  [ENTER]  ▲▼◄►  <Recipient>  ▲▼◄►  [ENTER] • Select a recipient group who receives the email notification. The group list will be displayed only if you added at least one group to the <Group>...
  • Page 81: Search & Play

    search & play SEARCH You can perform the search for recorded data by the time or by the search criteria such as an event. You can access the <Search> menu directly in Live mode. Scene Mode ► Live Status Record Status Audio Off Freeze Stop Alarm...
  • Page 82: Event Search

    search & play 3. The record data on the specific date will be listed. The display bar is different according to the data type. So check the data type for the color in the left pane. If DST (Daylight Saving Time) is configured, overlapping multiple recordings may be produced for a certain moment of time. Such a time section is distinguished with yellow color to mark DST section.
  • Page 83: Backup Search

    Backup Search Searches for backup data in the connected backup device. Only data in the format of NVR is included in the search. Refer to <Type> in "Backup > Backup". (Page 70) 1. Select <Backup Search> in the <Search> menu. 2.
  • Page 84: Playback

    search & play PLAYBACK Play You can play data stored in the HDD and backup a desired portion of the data. Scene Mode ► Live Status Record Status Audio Off Freeze Stop Alarm Record Play Search Backup Main Menu Shutdown Hide Launcher Logout 1.
  • Page 85 Using the Playback Button Name Description Play Timeline Indicates the current playback point, and can be used to move. Skip Backward Moves backward by unit time. Backward Fast Used for quick backward search while in Play. Play Backward Slow Play Used for backward frame-by-frame search while in PAUSE.
  • Page 86: Web Viewer

    web viewer INTRODUCING WEB VIEWER What is Web Viewer? Web Viewer allows remote access to your NVR(Network Video Recorder). You have access to live video, archived video, PTZ control (if configured), etc. Product Features • Remote connection using the browser •...
  • Page 87: Connecting Web Viewer

    CONNECTING WEB VIEWER 1. Open your web browser and type the IP address or URL of NVR into the URL address box. You must have specified the IP address in “Network > Connection Mode”. The URL connection will be enabled only when the DDNS connection settings have been completed. For more information, refer to “Network Configuration >...
  • Page 88: Using Live Viewer

    web viewer USING LIVE VIEWER The Live Viewer screen consists of following : This displays the IP address and the model name of the connected NVR. These menus consist of <LIVE>, <SEARCH>, <SETUP>, <ABOUT>. Select a split mode or full screen mode. Shows the IP address and model name of the connected NVR.
  • Page 89 OSD Information Display The channel number, video size, and IP address of the connected NVR are displayed. This icon will appear if the audio signal is currently being output. The current date and time will be displayed according to the selected time information display setting <NVR Time>...
  • Page 90 web viewer Connected NVR This displays the IP address and the status of the connecting NVR. Connection failure message No Response : Appears when the NVR does not respond. Access Denied : Appears when the maximum number of users is exceeded. The number of simultaneous connections are limited to 10.
  • Page 91 Saving the Live Screen on the PC • CAPTURE : Saves the current screen into a BMP or JPEG file. The default saving path is “C:\Program Files\Samsung\NVR Web Viewer\SnapShot\Live”. To change the saving path, click <SAVE PATH ( )> button and then select the path you want.
  • Page 92: Using Ptz Camera

    • RECORD : Saves the current image on the screen and saves it as a avi video file. To record it, it is required at least 1GB of available space. The default saving path is “C:\Program Files\Samsung\NVR Web Viewer\VideoClip\Live”. To change the saving path, click <SAVE PATH ( )>...
  • Page 93 • MENU : Appears the camera menu screen. • Up/Down/Left/Right : Available camera operation keys. • Tour : This is to call a group and its presets in order and to monitor the overall process. • Swing : Moves the camera lens direction between 2 points set for the camera.
  • Page 94: Using Search Viewer

    web viewer USING SEARCH VIEWER The Search Viewer screen consists of following : This displays the IP address and the model name of the connected NVR. These menus consist of <LIVE>, <SEARCH>, <SETUP>, <ABOUT>. These buttons are used for the screen split and full screen mode. Shows the IP address and model name of the connected NVR.
  • Page 95 Split-Screen You can change the split mode by clicking each number icon. <SINGLE MODE> <QUAD MODE> • Click < > button. The screen displays the selected camera connected to the NVR in “SINGLE MODE”. • Click < > button. The screen displays the selected camera connected to the NVR in “QUAD MODE”.
  • Page 96 PC.) To stop recording, click this button again. To record it, it is required at least 1GB of available space. The default saving path is “C:\Program Files\Samsung\NVR Web Viewer\VideoClip\Search”. To change the saving path, click <SAVE PATH ( )>...
  • Page 97: Searching The Recorded Video In The Calendar

    Searching the Recorded Video in the Calendar If the video data has been recorded on a date, the date is distinguished in green. If you click the date, the recorded video information is displayed in the time line. Click <Today> to change the date to today.
  • Page 98: Controlling Playback

    web viewer Controlling Playback Fast Backward : Reverse-plays faster. Each time you press the button, the play speed will switch to: x2, x4, x6, x8, x16, x32 and x64. Reverse Play : Performs Reverse Play. Play : Performs playback. Fast Forward : Plays faster. Each time you press the button, the play speed will switch to: x2, x4, x6, x8, x16, x32 and x64.
  • Page 99: Viewer Setup

    VIEWER SETUP You can configure the NVR settings remotely on the network. To configure the NVR settings, click <Setup>. System You can configure the various settings of the NVR system. Date/Time/Language For more information, refer to “Date/Time/Language” in the “System Setup” menu. (Page 43) Date/Time Set the date and time.
  • Page 100 web viewer Holiday You can set specific dates to Holidays according to your preferences. For more information, refer to “Setting Holiday” in the “System Setup” menu. (Page 44) Permission Management For more information, refer to <Permission Management> in the “System Setup” menu. (Page 45) Admin You can change the admin ID or the password.
  • Page 101 Setup You can set the user permission. System Management For more information, refer to <System Management> in the “System Setup” menu. (Page 49) System Information You can see information of the current system. Check the software version and MAC address. Device You can check a list of devices that are connected to the NVR and configure the necessary settings.
  • Page 102 web viewer Camera Setup You can change the settings of a connected network camera. Channel Setup You can configure the video settings for each channel. Storage Device You can check and change the settings related to the data storage device. Device You will see a list of storage devices that are connected to the NVR.
  • Page 103: Remote Device

    Remote Device You can specify the ID of a remote control that will operate in sync with NVR. Monitor Monitor You can configure the monitoring screen settings and set the output system. If the video is not played properly, refer to the troubleshooting section later in this manual.
  • Page 104: Record Setup

    web viewer Record For more information, refer to “Setting the Recording”. (Page 64) Recording Schedule If you set a recording schedule for a specific date and time, the recording will start at that specific time. Event Record Duration You can set the start and end times of recording that will be activated if an event occurs.
  • Page 105 Network Camera You can configure the record-related settings of the network camera. Record Option You can set the Disk End Mode. English _105...
  • Page 106 web viewer Event For more information, refer to “Setting the Event”. (Page 68) Sensor Detection NVR/Network Camera You can set the sensor operation mode and the synchronized camera as well as the alarm output type and the duration. If the connected network camera that has configured the alarm in/out settings triggers an alarm, NVR will perform the alarm out.
  • Page 107 Alarm Out Schedule You can schedule the alarm output according to the day of the week and the time. The default setting is Event Sync, which activates the alarm only if an event occurs. Network For more information, refer to “Network Configuration”. (Page 72) Connection Mode A remote user can access the NVR via the network to check the current mode and the IP address.
  • Page 108: Live Transfer

    web viewer DDNS Network 1/2 You can check the DDNS settings. Live Transfer You can configure the network transfer settings of the network camera. Mailing Service You can specify the SMTP server that sends a mail if an event occurs and set the recipient group and users. SMTP You can set the server that sends mails and specify if you use the authentication process.
  • Page 109: About

    Group You can add a group to receive the mail if an event occurs and set the permission to receive the event mail for each group. Recipient You can add a user or users who will receive the mail. ABOUT Click <ABOUT>.
  • Page 110: Backup Viewer

    backup viewer SEC BACKUP VIEWER You can play a file that is backed up in the format of SEC. Backup in the format of SEC will involve in generating two files: one for the backup data and one for the viewer. If you run the backup file viewer, the backup data file will be automatically played.
  • Page 111 Name Description A toggle button. Each time you press this button, the audio output will toggle between activated and deactivated. Audio You can adjust the volume level from 0 to 100. Enlarge the image by up to 100 times as big as the current one. Press the Zoom In( ) button the enlarge the image;...
  • Page 112 backup viewer Name Description A toggle button; each time you press this button, the "Slow Playback " icon changes its color to display it’s activated/deactivated. The play speed may differ depending on resolution. For more information, refer to “Speed difference according to the resolution”. A toggle button;...
  • Page 113: Appendix

    PRODUCT SPECIFICATION Item Details Model SRN-470D SRN-1670D Video In Max. 4CH Max. 16CH Video Out VGA(1)/ HDMI(1) VGA(1)/ HDMI(1) Compression H.264, MJPEG, MPEG-4 H.264, MJPEG, MPEG-4 Speed 120fps, 4CIF(704x480) 240fps, 4CIF(704x480) Split Mode 1/4/Auto Sequence 1/4/6/8/9/13/16/Auto Sequence Display VGA(1024x768/1280x1024(60Hz))/...
  • Page 114 Item Details Model SRN-470D SRN-1670D Interface RJ-45, Gigabit Ethernet x 2 RJ-45, Gigabit Ethernet x 2 TCP/IP, DHCP, PPPoE, SMTP, NTP, TCP/IP, DHCP, PPPoE, SMTP, NTP, Protocols HTTP, DDNS, RTP, RTSP HTTP, DDNS, RTP, RTSP Network Program NET-i viewer, Webviewer...
  • Page 115: Product Overview

    PRODUCT OVERVIEW • SRN-470D unit : mm (inches) DVD- DVD RECORDER 215.0 (8.46) English _115...
  • Page 116 appendix • SRN-1670D unit : mm (inches) 440(17.32”) NETWORK VIDEO RECORDER SRN-1670D 116_ appendix...
  • Page 117: Default Setting

    DEFAULT SETTING This returns the factory default settings. To reset the system, move to “System Management > Settings > Load Factory Default” and press the <Default> button. The default settings are based on SRN-1670D. The default password can be exposed to a hacking thread so it is recommended to change the password after installing the product. Note that the security and other related issues caused by the unchanged password shall be responsible for the user.
  • Page 118 appendix Category Details Factory Default Event Display Display Monitor Multi CH SEQ Time 5 sec Device Monitor Video Output VGA(1280x1024) Display Position Setup Mode Live Screen Recording Schedule CH1~CH16 Both(Cont&Evnt) Pre Event Event Record Duration POST Event 1 min Standard REC Rate Full Frame Record Record Setup...
  • Page 119 Category Details Factory Default Address Type Static IP Bandwidth Unlimited Static IP 192.168.1.200 Network1 Gateway 192.168.1.1 Subnet Mask 255.255.255.0 168.126.63.1 Address Type Static IP Bandwidth Unlimited Static IP 192.168.2.200 Network2 Connection Mode Gateway 192.168.2.1 Subnet Mask 255.255.255.0 168.126.63.1 Protocol Type Port (TCP) Network Port (UDP)
  • Page 120: Troubleshooting

    appendix TROUBLESHOOTING Problem Action  Check if the power supply system is properly connected. The system does not turn on and the indicator on the  Check the system for the input voltage from the power source. front panel does not work at all. ...
  • Page 121 Problem Action  Check the registered Camera if it support PTZ function. No response controlling PTZ in the live viewer  Check if the network cable is connected properly. The camera is not connected or the PC fails to connect to the product. ...
  • Page 122 appendix Problem Action  When you are backing up data, you have choices about the player either: PC Backup data is just not played by the PC or NVR. or NVR. Make your selection before proceeding.  If you are using the PC to play the data, the format of the backup file should be either SEC.
  • Page 123: Open Source License Report On The Product

    Corresponding Source code from us for a period of three years after our last shipment of this product by sending email to help.cctv@samsung.com If you want to obtain the complete Corresponding Source code in the physical medium such as CD-ROM, the cost of physically performing source distribution might be charged.
  • Page 124 In addition, mere aggregation of another work not based on the Program It is not the purpose of this section to induce you to infringe any patents with the Program ( or with a work based on the Program ) on a volume of or other property right claims or to contest validity of any such claims;...
  • Page 125: Terms And Conditions

    one line to give the program’s name and an idea of what it does. For example, if you distribute copies of such a program, whether gratis or for a fee, you must pass on to the recipients the same freedoms that Copyright (C) yyyy name of author you received.
  • Page 126 An interactive user interface displays “Appropriate Legal Notices” to the Conveying under any other circumstances is permitted solely under the extent that it includes a convenient and prominently visible feature that (1) conditions stated below. Sublicensing is not allowed; section 10 makes it displays an appropriate copyright notice, and (2) tells the user that there unnecessary.
  • Page 127 a) Convey the object code in, or embodied in, a physical product The requirement to provide Installation Information does not include a (including a physical distribution medium), accompanied by the requirement to continue to provide support service, warranty, or updates Corresponding Source fixed on a durable physical medium for a work that has been modified or installed by the recipient, or for the customarily used for software interchange.
  • Page 128 8. Termination. Each contributor grants you a non-exclusive, worldwide, royalty-free patent license under the contributor's essential patent claims, to make, You may not propagate or modify a covered work except as expressly use, sell, offer for sale, import and otherwise run, modify and propagate provided under this License.
  • Page 129 14. Revised Versions of this License. Preamble The Free Software Foundation may publish revised and/or new versions The licenses for most software are designed to take away your freedom of the GNU General Public License from time to time. Such new versions to share and change it.
  • Page 130 Although the Lesser General Public License is Less protective of the you distribute them as separate works. But when you distribute the users’ freedom, it does ensure that the user of a program that is linked same sections as part of a whole which is a work based on the Library, with the Library has the freedom and the wherewithal to run that program the distribution of the whole must be on the terms of this License, whose using a modified version of the Library.
  • Page 131 You must give prominent notice with each copy of the work that the 10. Each time you redistribute the Library (or any work based on the Library is used in it and that the Library and its use are covered by this Library), the recipient automatically receives a license from the original License.
  • Page 132: Openssl License

    16. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR 5. Products derived from this software may not be called “OpenSSL” nor AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY may “OpenSSL” appear in their names without prior written permission OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE of the OpenSSL Project.
  • Page 133 Copyright ( c ) 2004, Kneschke, incremental All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met : - Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
  • Page 134 Correct Disposal of This Product (Waste Electrical & Electronic Equipment) (Applicable in the European Union and other European countries with separate collection systems) This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB cable) should not be disposed of with other household waste at the end of their working life.
  • Page 135 SAMSUNG TECHWIN AMERICA Inc. SAMSUNG TECHWIN EUROPE LTD. 100 Challenger Rd. Suite 700 Ridgefield Park, NJ 07660 Samsung House, 1000 Hillswood Drive, Hillswood Business Park Toll Free : +1-877-213-1222 Direct : +1-201-325-6920 Chertsey, Surrey, UNITED KINGDOM KT16 OPS Fax : +1-201-373-0124 TEL : +44-1932-45-5300 FAX : +44-1932-45-5325 www.samsungcctvusa.com...

This manual is also suitable for:

Srn-1670d

Table of Contents