Related Manuals for Radio Shack 65562
Summary of Contents for Radio Shack 65562
- Page 1 49-329.fm Page 1 Thursday, June 1, 2000 7:46 AM Passive Infrared Sensor Alarm with Keychain Remote...
-
Page 2: Table Of Contents
49-329.fm Page 2 Thursday, June 1, 2000 7:46 AM ˆ Contents Features ..............3 Preparation ............5 Installing Batteries ..........5 Setting the Security Code ........9 Resetting the Security Code ......13 Installation ............13 Choosing a Mounting Location ......14 Temporarily Placing the Sensor Alarm .... -
Page 3: Features
49-329.fm Page 3 Thursday, June 1, 2000 7:46 AM ˆ Features Your RadioShack Passive Infrared Sensor Alarm is a high-quality, battery-operated security device. It uses a passive infrared (PIR) motion sensor to detect in- truders and activate a built-in alarm. The sensor alarm’s features include: Wireless RF (Radio Frequency) Operation —... - Page 4 49-329.fm Page 4 Thursday, June 1, 2000 7:46 AM Chime — lets you select a more pleasant sounding doorbell-type chime as the audible alarm. Panic Alarm — sounds the alarm immediately if you press on the main unit or if you press both PANIC (at the same time) on the remote control.
-
Page 5: Preparation
49-329.fm Page 5 Thursday, June 1, 2000 7:46 AM ˆ Preparation INSTALLING BATTERIES The main unit of your sensor alarm requires four AA batteries (not supplied) for power. For the best perfor- mance and longest life, we recommend alkaline bat- teries (available at your local RadioShack store). - Page 6 49-329.fm Page 6 Thursday, June 1, 2000 7:46 AM management authorities for information on recycling or disposal programs in your area or call 1-800-822- 8837. Some options that might be available are: mu- nicipal curbside collection, drop-off boxes at retailers such as your local RadioShack store, recycling collec- tion centers, and mail-back programs.
- Page 7 49-329.fm Page 7 Thursday, June 1, 2000 7:46 AM 2. Place the batteries in the compartment and on top of the attached ribbon, as indicated by the polarity symbols (+ and –) marked inside. Note: As soon as you press the last battery in place, the alarm sounds a loud chirp and both the red and the green indicators light briefly.
- Page 8 49-329.fm Page 8 Thursday, June 1, 2000 7:46 AM replace these batteries, be sure to apply the cur- rent security code to the remote control so the sensor alarm will recognize the remote signals (see “Remote Control” on Page 11). When the main unit’s indicator flashes LOW BATT...
-
Page 9: Setting The Security Code
49-329.fm Page 9 Thursday, June 1, 2000 7:46 AM SETTING THE SECURITY CODE Main Unit You can use a four-digit security code to disarm the alarm. The default code is 1234. Follow these steps to set a new security code at any time. Red Indicator Green Indicator INSTANT... - Page 10 49-329.fm Page 10 Thursday, June 1, 2000 7:46 AM 2. If necessary, disarm the sensor alarm (the red indicator should not be flashing) by entering the current security code. 3. Press . The sensor alarm beeps once and PROG the green PROG indicator lights. 4.
- Page 11 49-329.fm Page 11 Thursday, June 1, 2000 7:46 AM “Arming and Disarming the Sensor Alarm” on Page 19). Remote Control Each time you remove and replace the batteries in the main unit, you must program the main unit to rec- ognize the remote control’s signals.
- Page 12 49-329.fm Page 12 Thursday, June 1, 2000 7:46 AM 4. Enter your four-digit security code. The sensor alarm beeps three times and its PROG indicator flashes quickly. 5. Press on your remote control. DISARM The alarm’s PROG indicator lights steadily and the sensor alarm chirps, indicating that it received the remote signal.
-
Page 13: Resetting The Security Code
49-329.fm Page 13 Thursday, June 1, 2000 7:46 AM es the remote signals (see “Arming and Disarming the Sensor Alarm” on Page 19). RESETTING THE SECURITY CODE If you ever forget your security code, you can easily reset it to the default code (1234) by removing and re- installing the main unit’s batteries (see “Installing Bat- teries”... -
Page 14: Choosing A Mounting Location
49-329.fm Page 14 Thursday, June 1, 2000 7:46 AM • out of strong drafts, like those caused by central heating vents or air conditioners or air movement around fireplaces, exterior walls and windows, and refrigerators • so it does not detect your pet’s movements CHOOSING A MOUNTING LOCATION The sensor alarm’s main unit is designed to be mounted on a smooth, flat wall surface. -
Page 15: Temporarily Placing The Sensor Alarm
49-329.fm Page 15 Thursday, June 1, 2000 7:46 AM TEMPORARILY PLACING THE SENSOR ALARM Before you permanently mount the sensor alarm, temporarily place it at the selected location so you can check the coverage area. You might need to check several different locations to find the best one. Place the main unit on a stepladder (for example) at the recommended height, then move the stepladder to various locations in the room(s) you want to pro-... - Page 16 49-329.fm Page 16 Thursday, June 1, 2000 7:46 AM 3. Set the main unit’s slide switch to . A door- CHIME bell-type chime immediately sounds. INSTANT DELAY CHIME LOW BATT PROG 4. Walk around in the protected area. When the sensor alarm detects your motion, the chime sounds again.
-
Page 17: Mounting The Sensor Alarm
49-329.fm Page 17 Thursday, June 1, 2000 7:46 AM MOUNTING THE SENSOR ALARM After you determine the best location for your sensor alarm, follow these steps to mount it on the wall. 1. If necessary, disarm the sensor alarm (the red indicator should not be flashing) by entering the current security code. - Page 18 49-329.fm Page 18 Thursday, June 1, 2000 7:46 AM 4. Turn the main unit clockwise (so the right screw head slides into the curved groove) until it is secure. Installation...
-
Page 19: Operation
49-329.fm Page 19 Thursday, June 1, 2000 7:46 AM ˆ Operation We recommend that you test the sensor alarm at least once a month by arming and disarming it as de- scribed in the following section. ARMING AND DISARMING THE SENSOR ALARM Arming To have the alarm’s siren sound as soon as the sen-... - Page 20 49-329.fm Page 20 Thursday, June 1, 2000 7:46 AM To have the alarm’s siren sound about 30 seconds af- ter the sensor detects motion, set the slide switch to DELAY To arm the sensor alarm, press on the main unit or on the remote control.
- Page 21 49-329.fm Page 21 Thursday, June 1, 2000 7:46 AM the indicator flashes every second for about 30 sec- onds, then the alarm siren sounds and the indicator stays on. The alarm siren sounds for up to 2 minutes. To stop it sooner, disarm the alarm (see “Disarming”).
-
Page 22: Using The Chime Alarm
49-329.fm Page 22 Thursday, June 1, 2000 7:46 AM Notes: • You can temporarily silence the alarm only once each time you disarm it. • If entering your security code does not disarm the sensor alarm, try entering the default code (1234). -
Page 23: Using The Panic Alarm
49-329.fm Page 23 Thursday, June 1, 2000 7:46 AM sounds every time the sensor detects motion. To turn off the chime, set the slide switch to either INSTANT DELAY USING THE PANIC ALARM If you want to startle an intruder (for example) by in- stantly sounding the alarm siren, simply press PANIC on the main unit or press... -
Page 24: Care
49-329.fm Page 24 Thursday, June 1, 2000 7:46 AM ˆ Care To enjoy your RadioShack Passive Infrared Sensor Alarm for a long time: • Keep the sensor alarm and remote dry. If they do get wet, wipe them dry immediately. •... -
Page 25: Replacing The Remote Control's Battery
49-329.fm Page 25 Thursday, June 1, 2000 7:46 AM REPLACING THE REMOTE CONTROL’S BATTERY Your sensor alarm’s remote control uses the supplied 12V alkaline battery for power. When the remote con- trol’s indicator lights dimly or not at all when you press , or if the remote control stops operat- DISARM ing properly (the main unit cannot receive the remote... -
Page 26: Fcc Statement
49-329.fm Page 26 Thursday, June 1, 2000 7:46 AM Note: You do not need to reset the remote control or main unit after replacing the remote’s battery. Cautions: • Dispose of the old battery promptly and properly. Do not burn or bury it. •... -
Page 27: Specifications
49-329.fm Page 27 Thursday, June 1, 2000 7:46 AM radio communications. However, there is no guaran- tee that interference will not occur in a particular in- stallation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the inter- ference by one or more of the following measures:... - Page 28 49-329.fm Page 28 Thursday, June 1, 2000 7:46 AM Operating Ambient Temperature ......32–122°F (0–50°C) Operating Relative Humidity ......Less than 95% Auto Alarm Reset Time ......120 ±5 Seconds Siren Output Sound Pressure Level: About 108 dB at 1 Foot (34 cm) Internal PIR Detection Area ......
- Page 29 49-329.fm Page 29 Thursday, June 1, 2000 7:46 AM Limited Ninety-Day Warranty This product is warranted by RadioShack against manufacturing defects in material and workmanship under normal use for ninety (90) days from the date of purchase from RadioShack company-owned stores and authorized RadioShack franchisees and dealers.
- Page 30 49-329.fm Page 30 Thursday, June 1, 2000 7:46 AM (continued) (c) refund the purchase price. All replaced parts and products, and products on which a refund is made, become the property of RadioShack. New or reconditioned parts and prod- ucts may be used in the performance of warranty service. Re- paired or replaced parts and products are warranted for the remainder of the original warranty period.