Starting And Maintaining A Fire; Combustion Control; Refueling For Best Performance; Smoking - Causes And Troubleshooting - Lennox Hearth Products Montecito MONTE Installation And Operation Instructions Manual

Epa wood-burning fireplace signature collection
Hide thumbs Also See for Montecito MONTE:
Table of Contents

Advertisement

Building a Fire

(starting and maintaining a fire)

To start a fire, place several crumpled up balls of
newspaper in the firebox. Place small dry pieces
of kindling on top of the paper, criss-crossing the
kindling so that there are air spaces in between.
Keep the fuel far back enough so that air can
get underneath. Open the air controls fully
and light the newspaper. Once the newspaper
and the kindling is well ignited, close the door.
Once the kindling fire is well established, cord
wood can be added (see Primary Air Combus-
tion Control section for proper operation of the
air controls).
The unit will burn best with 2-3 pieces of cord
wood spaced 1 to 2 inches apart and allowing air
to get under the fuel. Criss-crossing or arrang-
ing the fuel so that air can get underneath, will
help the fire to get started easily. The unit should
be operated with the air control fully open long
enough to get the cord wood well ignited.
COMBUSTION CONTROLS
Primary Air and Air Boost Controls
There is no flue damper in the Montecito™ wood
burning fireplace. As is common with air tight
stoves, the combustion air control sets the flow
of air entering the firebox. This allows for a
more precise control of the fire. The combus-
tion air control is located below the door on
the left side. The main source of air (primary
air) entering the firebox can be diminished by
moving the air combustion control from left
to right. The primary air is fully opened when
the air control is completely moved to the left.
The air control device can also be used to add
an extra boost of air especially during fire start
up and reloading of the unit.
Combustion Air Register
Figure 1
4
Pulling the air combustion control will induce an
air boost at the base of the fire allowing an easier
fire start up. When the fire is well established,
the control can be pushed in to shut down the
air boost allowing for a longer burn time. The
combustion air control should be in the closed
position (primary air and air boost) when the
fireplace is not in use. This will minimize air
leakage up the chimney. The combustion air
control should be opened before opening the
door to minimize the possibility of back draft
coming into the room.
Accelerated Combustion
The maximum heat output for the Montecito
fireplace is achieved by burning with the door
closed and the combustion air opened and
pulled out. By this method, the Montecito
fireplace can produce up to 55,000 BTU of
heat per hour. However, it will be necessary
to reload with wood every one or two hours.
This is the least efficient method of burning the
Montecito fireplace.
Use caution when firing with the combustion
air control wide open. Only burn cord wood in
this manner. Small dry pieces of softwood and
construction scraps will burn very intensely us-
ing this method and may damage the firebox.
Medium Combustion
This is the recommended mode of operating
the Montecito fireplace and should be the one
normally used since it will deposit the least
amount of creosote on the glass and in the
chimney. The combustion air control must be
3/4 closed and pushed in to close the air boost.
The precise setting will depend on many fac-
tors, including chimney length and the moisture
content of the wood.
Push to Close Air Boost
Pull to Open Air Boost
Close
Open
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
For instance, a long chimney will necessitate
closing the damper more. To obtain the proper
combustion, close the damper completely, then
open it about 1/4" to 1/2". Three medium size
pieces of wood should be burning on a bed of
hot coals. The heat output will be approximately
30,000 BTU per hour and the loading time will
be about every 3-4 hours. Softwoods may be
burned using this method but the time will be
substantially reduced.
Slow Combustion
When the air combustion control is completely
closed, the fireplace is in a slow combustion phase.
If the hearth is hot enough, slow combustion will
not extinguish the fire, but there will be a notice-
able change in the flame pattern. The flames will
be slow and may appear dirty if the wood is too
wet (moisture content of 20% and more). Do not
allow the wood to burn without flame, since this
will produce excessive creosote in the unit.
Creosote may accumulate on the glass door.
This method of burning should be used only
after operating the Montecito fireplace with
the air control opened to produce a hot fire for
about an hour or at medium pace for at least
three (3) hours. Slow combustion can be used
at night in order to reduce the heat output and
to prolong the burn. The loading time will be
between 6-8 hours.

REFUELING FOR BEST PERFORMANCE

The Montecito fireplace will operate best if at-
tention is given to operating the unit with the
damper fully opened after refueling in order
to bring the firebox and the chimney system
up to their optimum operating temperature.
Combustion efficiency is relative to firebox
temperature. A temperature of 500º C (932º F)
and up, with a visible flame, in the upper part
of the firebox indicates a maximum efficiency.
To obtain this temperature, the fireplace must
be operated with the primary air and air boost
controls fully opened during 10 to 20 minutes
after reloading, depending on the heat and on
the moisture content of the wood.
Once you have reached the desired temperature,
the air boost can be closed and the primary air
set to a medium setting. You know you have
reached the desired temperature when, closing
the primary air control, you can see a flame
at the top of the firebox. The benefit of this
technique will be cleaner glass, less creosoting,
greater efficiency and the most pleasing fire for
your enjoyment.
SMOKING –
CAUSES AND TROUBLESHOOTING
To reduce the likelihood of smoking when open-
ing the door, set the combustion air controls to
the left before opening the door. Your fireplace
has been designed and tested to provide smoke
free operation. Occasionally, there may be a
small amount of smoking upon lighting the fire,
until the chimney heats up but this should not
continue. If the fireplace continues to smoke it
is probably for one of the following reasons:

Advertisement

Table of Contents
loading

Table of Contents