Table of Contents
Advertisement
Installer: Leave This Manual With The Appliance.
Consumer: Retain This Manual For Future Reference.
A French manual is available upon request. Order P/N 775,157CF.
Ce manuel d'installation est disponible en francais, simplement
en faire la demande. Numéro de la pièce 775,157CF.
• Hot! Do not touch! The glass and surfaces of this appliance will be hot during operation and will
retain heat for a while after shutting off the appliance. Severe burns may result.
• Carefully supervise children in the same room as appliance.
• If small children are present in the home, it is recommended that this appliance be fitted with a
screen door or screen panel kit. See Page 14 for ordering information.
• Suitable for installation into masonry or factory built fireplaces.
• Lennox™ gas-burning appliances are designed for use as a supplemental heater. They are not intended for
continuous use as a primary heat source.
WARNING: If the information in this manual is not
followed exactly, a fire or explosion may result
causing property damage, personal injury or loss
of life.
Do not store or use gasoline or other flammable
vapors or liquids in the vicinity of this or any other
appliance.
WHAT TO DO IF YOU SMELL GAS:
• Do not light any appliance.
• Do not touch any electrical switch; do not
Use any phone in your building.
• Immediately call your gas supplier from a
neighbor's phone. Follow your gas supplier's
instructions.
• If your gas supplier cannot be reached, call
the fire department.
Installation and service must be performed by a quali-
fied installer, service agency or the gas supplier
CARE AND OPERATION INSTRUCTIONS
Direct-Vent Gas
Fireplace Heater Inserts
P/N 775,157M Rev. J, 12/2007
US
Report No. 116-F-14-5
WARNINGS
AVERTISSEMENT: Assurez-vous de bien suivre les
instructions donné dans cette notice pour réduire au
minimum le risque d'incendie ou pour éviter tout dom-
mage matériel, toute blessure ou la mort.
POUR VOTRE SÉCURITÉ: Ne pas entreposer ni utiliser
d'essence ni d'autre vapeurs ou liquides inflammables dans
le voisinage de cet appareil ou de tout autre appareil.
POUR VOTRE SÉCURITÉ: Que faire si vous sentez une odeur
de gaz:
• Ne pas tenter d'allumer d'appareil.
• Ne touchez à aucun interrupteur. Ne pas vous servir
des téléphones se trouvant dans le batiment où vous
vous trouvez.
• Evacuez la piéce, le bâtiment ou la zone.
• Appelez immédiatement votre fournisseur de gaz depuis
un voisin. Suivez les instructions du fournisseur.
• Si vous ne pouvez rejoindre le fournisseur de gaz,
appelez le service dos incendies.
L'installation et service doit être exécuté par un qualifié instal-
.
leur, agence de service ou le fournisseur de gaz.
Models: EDVI25, EDVI30 & EDVI35
Advertisement
Table of Contents
Related Manuals for Lennox Hearth Products EDVI30
Summary of Contents for Lennox Hearth Products EDVI30
- Page 1 Suivez les instructions du fournisseur. • Si vous ne pouvez rejoindre le fournisseur de gaz, appelez le service dos incendies. L’installation et service doit être exécuté par un qualifié instal- leur, agence de service ou le fournisseur de gaz. Models: EDVI25, EDVI30 & EDVI35...
-
Page 2: Important Safety And Warning Information
IMPORTANT SAFETY AND WARNING INFORMATION READ THIS MANUAL IN ITS ENTIRETY AND UNDER-STAND THESE RULES TO FOLLOW FOR SAFETY. WARNING Improper installation, adjust- ment, alteration, service or maintenance can cause injury or property damage. Refer to this manual. For assistance or additional information consult a qualified installer, service agency or the gas supplier. -
Page 3: Table Of Contents
We extend our continued support to help you achieve the maximum benefit and enjoyment available from your new gas-fired heater. It is our goal at Lennox Hearth Products to provide you, our valued customer, with an appliance that will ensure years of trouble-free warmth and pleasure. -
Page 4: Burn-In Period
4 on Page 4. Once the pilot is lit, and valve knob is in the ON posi- tion, the ON/OFF switch will control the appliance ON/OFF operation. To operate, toggle the switch between its ON and OFF positions. Variable Flame Height Adjustment These millivolt appliances are equipped with a variable gas control valve. Flame height may be adjusted through a range between fixed low and high settings by rotating the HI/LO knob on the valve (see Figures 1 & 2) alternately, while the appliances are in operation. MODELS: EDVI30 & EDVI35 Honeywell Millivolt Gas Valve Controls PIEZO CONVERTIBLE IGNITER PILOT HI/LO REGULATOR ADJUSTMENT GAS CONTROL (adjusts flame height SCREW KNOB... -
Page 5: Operation/Care Of Your Appliance
OPERATION AND CARE OF YOUR APPLIANCE Appliance operation may be controlled through a remotely located optional wall thermostat or remote control. In lieu of remote control or remote wall thermo- stat operation, the appliance must be operated directly through the on/off switch located on the surround panel (see Figure 4). If your millivolt appliance is equipped with an optional wall thermostat kit or remote control kit and the pilot is lit (and valve is in the On position), the appliance main burner may be turned on and off with the wall thermostat or remote control. Always keep the appliance area clear and free from combustible materials, gasoline and other flammable liquids. Remember, Millivolt appliances have a continu- ous burning pilot flame. Exercise caution when using products with combustible vapors. MAINTENANCE The appliance and venting system should be thoroughly inspected before initial use and at least annually by a qualified service technician. However, more frequent periodic inspections and cleanings should be performed by the homeowner. Homeowner must contact a quali- fied service technician at once if any abnormal condition is observed. - Page 6 Label all wires prior to discon- nection when servicing con- trols. Wiring errors can cause improper and dangerous appli- ance operation. 13. (EDVI30 only) Remove the two blower mounting screws and remove blower per instructions in Figure 11. Disconnect wires from terminals & green ground wire after blower is pulled forward.
-
Page 7: Maintenance Schedule
MAINTENANCE SCHEDULE Annually (Before the onset of the Burning Season) Maintenance Task Inspecting/Cleaning Burner, Logs and Controls Check Flame Patterns and Flame Height Inspecting/Cleaning Pilot and Burner Checking Vent System Appliance Checkout Replacing Rockwool Ember Materials Periodically (After the Burning Season) Maintenance Task Cleaning Firebox Interior Check Flame Patterns and Flame Height Checking Vent System Cleaning Front Door Window Accomplishing Person Qualified Service Technician Inspect valve and ensure it is properly operating. Check piping for leaks. Vacuum the control compartment, fireplace logs and burner area. Qualified Service Technician Refer to Figure 19 on Page 8 and verify the flame pattern and height displayed by the appliance conforms to the picture. -
Page 8: Front Glass Enclosure Panel, Removal And Installation
PROCEDURE FOR REMOVING THE STANDARD GLASS DOOR ASSEMBLY WARNING Handle glass door with extreme care! The glass door assembly is susceptible to damage. Do not scratch while handling or while reinstalling. WARNING Never operate unit without the front glass door panel in place and secure. - Page 9 If air shutter is open Flame will be blue too far Table 5 LOGS, VERMICULITE AND EMBERS - Models EDVI5 & EDVI30 (For EDVI35 Log Installation Instructions, see Page 11). Installation Instructions If logs are not installed according to the directions shown here, flame impingement and improper combustion could occur and result in soot and/or excessive production of carbon monoxide (CO) - a colorless, odorless, toxic gas.
- Page 10 1. Place the rear log onto the two corresponding locating pins at the back of the firebox as shown in Figure 22. Rear Log Figure 22 . Place the Front Right Log onto the two corresponding locating pins as shown in Figure 23. Figure 23 3. Place the Center Log onto the two corresponding locating pins as shown in Figure 24. Figure 24 Center Log 4. Place the Front Left Log onto the two corresponding locating pins as shown in Figure 25. Figure 25 5. Install the Top Left Log onto the corresponding locating pin and indentation on Center Log as shown in Figure 26. Figure 26 6. Install the Front Center Log over the Front Right Log . The front Front Right Log of log will rest on the burner and the back of log will rest on rear log as shown in Figure 27. Figure 27 7. Install the Top Right Log into the corresponding indentations on Front Center Log and Locating Pin as shown in Figure 28. NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE Front Left Log Top Left Log Front Center Log...
- Page 11 Figure 28 Top Right Log 8. Place the glowing embers on the burner as shown in Figure 29. One package of ember material has been included with this log set You will not need to use the entire bag. IMPORTANT: The quantity and placement of the ember material can affect insert performance therefore it is very important that it be placed as shown in Figure a. Unpackage and divide the fine ember material (mineral wool) into dime-sized fluffy pieces.
- Page 12 Carefully install the seven-piece log set into the firebox as shown in these instructions. All logs should fit onto corresponding pins and/or log stoppers. This will ensure a proper flame and safe combustion. 1. Place some vermiculite around the burner as shown in Figure 32 (the entire bag of vermiculite will NOT be used). . Place the Rear Log onto the two corresponding locating pins at the back of the firebox as shown in Figure 32. Rear Log Figure 32 Vermiculite 3. Place the Front Right Log and the Center Left Log onto the two corresponding locating pins (each) as shown in Figure 33. Center Left Log Figure 33 4. Place the Front Left Log onto the two corresponding locating pins, then place the Top Left Log onto the locating pin on the Center Left Log (the log will rest in the corresponding indent on Rear Log). See Figure 34. Top Left Log Front Left Log Figure 34 5. Place the Front Center Log in place as shown in Figure 35. The back of the log fits into the corresponding indent on Rear Log. Figure 35 6. Install the Top Right Log into the corresponding indentations on Front Center Log and Front Right Log as shown in Figure 36. Figure 36 7. Place the glowing embers on the burner as shown in Figure 37. One package of ember material has been included with this log set You will not need to use the entire bag.
-
Page 13: Millivolt Appliance Checkout
MILLIVOLT APPLIANCE CHECKOUT Light the pilot by following the instructions Pages 16 or 17 of this manual. The pilot flame should be steady, not lifting or floating. Flame should be blue in color with traces of orange at the outer edge. The top 3/8" (10 mm) at the pilot generator (thermopile) and the top 1/8" minimum (tip) of the quick drop out thermocouple should be engulfed in the pilot flame. The flame should project 1" (25 mm) beyond the hood at all three ports (Figure 38). Replace logs if removed for pilot inspec- tion. Proper Pilot Flame Appearance Thermocouple Igniter Rod ¹⁄₈" Min Hood (3 mm) ³⁄₈"... -
Page 14: Accessory Components
These decorative screen door panels fit over the standard glass door panels. Cat. No. Model Description H1501 TPSDK-5 Twin-Pane Screen Door Kit, EDVI5 H0877 TPSDK-30DVI Twin-Pane Screen Door Kit, EDVI30 H0878 TPSDK-35I Twin-Pane Screen Door Kit, EDVI35 Brickaded Liner Kits The brickaded liner kits include panels for the rear and side walls of the firebox. The panels have brick-like features in relief. These kits can be retrofitted into previously installed Elite™ inserts. -
Page 15: Wall Thermostat
FLK-30DVI Flat Louver Kit, Charcoal, EDVI30 H0887 FLK-30DVIG Flat Louver Kit, Gold, EDVI30 H0888 FLK-30DVIBS Flat Louver Kit, Brushed Stainless, EDVI30 H0889 FLK-35 Flat Louver Kit, Charcoal, EDVI35 H0890 FLK-35G Flat Louver Kit, Gold, EDVI35 H0891 FLK-35BS Flat Louver Kit, Brushed Stainless, EDVI35... -
Page 16: Lighting Instructions - Millivolt
WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE. A. This appliance has a pilot which must be lighted with a piezo igniter. When lighting the pilot, follow these instructions exactly. B. BEFORE OPERATING, smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor. WHAT TO DO IF YOU SMELL GAS • Extinguish any open flame. - Page 17 INSTRUCTIONS D’ALLUMAGE – VANNE GAZ MILLIVOLT POUR VOTRE SÉCURITÉ, LISEZ CES INSTRUCTIONS AVANT L’ALLUMAGE AVERTISSEMENT : SI VOUS NE SUIVEZ PAS CES INSTRUCTIONS À LA LETTRE, IL POURRAIT S’EN SUIVRE UN INCENDIE OU UNE EXPLOSION CAUSANT DES DOMMAGES MATÉRIELS, DES BLESSURES CORPORELLES OU MÊME DES PERTES DE VIE. A. Cet appareil est muni d’une veilleuse qui doit être allumée avec un allumeur piézo-électrique. Lorsque vous allumez la veilleuse, suivre exactement ces instructions.
-
Page 18: Replacement Parts List
Room Air Blower System Blower Assembly, 7” Blower Assembly, 9" Power Cord Rheostat (knob included) Knob, Rheostat Switch, Temp. Control (TOD) Where Used EDVI5 EDVI30 & EDVI35 EDVI5 EDVI30 & EDVI35 EDVI5 & EDVI30 EDVI35 EDVI30 EDVI35 EDVI5 EDVI5 EDVI30... -
Page 19: Parts Diagrams
REPLACEMENT PARTS DIAGRAMS NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE... -
Page 20: Troubleshooting Guide - Millivolt
TROUBLESHOOTING THE MILLIVOLT GAS CONTROL SYSTEM Note: Before troubleshooting the gas control system, be sure external gas shut off valve (located at gas supply inlet) is in the “ON” position. Important: Valve system troubleshooting should only be accomplished by a qualified service technician. SYMPTOM 1) Spark igniter will not light A. - Page 21 NOTES: THIS PAGE LEFT BLANK INTENTIONALLY...
- Page 22 NOTES: THIS PAGE LEFT BLANK INTENTIONALLY...
- Page 23 NOTES: THIS PAGE LEFT BLANK INTENTIONALLY...
-
Page 24: Product Reference Information
Fuel Type (Check one) c Natural Gas c Propane Gas (LP) Lennox reserves the right to make changes at any time, without notice, in design, materials, specifications, prices and also to discontinue colors, styles and products. Consult your local distributor for fireplace code information. Printed in U.S.A. © LENNOX HEARTH PRODUCTS 2003 P/N 775,157M REV. J 1/007 Normally, all parts should be ordered through your Lennox distributor or dealer. Parts will be shipped at prevailing prices at time of order. When ordering repair parts, always give the following information: 1. The model number of the appliance. . The serial number of the appliance. 3. The part number. 4. The description of the part. 5. The quantity required. 6. The installation date of the appliance. If you encounter any problems or have any questions concerning the installation or application of this system, please contact your dealer. LENNOX HEARTH PRODUCTS 1110 West Taft Orange, CA 92865 visit us at www.Lennox.com 1110 West Taft Avenue • Orange, CA 9865...