Land Pride Accuz Z52 , Z60, Z72 Operator's Manual

Zero turning radius mowers
Hide thumbs Also See for Accuz Z52 , Z60, Z72:
Table of Contents

Advertisement

Accu-Z
®
®
Z52
, Z60
& Z72
19097
®
®
Zero Turning Radius Mowers
356-005M
Operator's Manual
!
Read the Operator's manual entirely. When
you see this symbol, the subsequent
instructions and warnings are serious - follow
without exception. Your life and the lives of
others depend on it!
© Copyright 2003 Printed
Cover photo may show optional equipment not supplied
with standard unit.
03/11/03

Advertisement

Table of Contents
loading

Summary of Contents for Land Pride Accuz Z52 , Z60, Z72

  • Page 1 Accu-Z ® ® ® , Z60 & Z72 19097 ® Zero Turning Radius Mowers 356-005M Operator’s Manual Read the Operator’s manual entirely. When you see this symbol, the subsequent instructions and warnings are serious - follow without exception. Your life and the lives of others depend on it! ©...
  • Page 2: Table Of Contents

    Copyright 2003 All rights Reserved Land Pride provides this publication “as is” without warranty of any kind, either expressed or implied. While every precaution has been taken in the preparation of this manual, Land Pride assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained herein. Land Pride reserves the right to revise and improve its products as it sees fit.
  • Page 3: Important Safety Information

    Land Pride Important Safety Information Important Safety Information These are common practices that may or may not be applicable to the products described in this manual. Be Aware of Signal Words A signal word designates a degree or level of hazard seriousness. The...
  • Page 4 Dismounting from a moving mower could cause serious injury or death. Keep hands, feet, and clothing away from power-driven parts. Wear snug fitting clothing to avoid entanglement with moving parts. Make sure all persons are clear of working area. Land Pride 03/11/03...
  • Page 5: Safety Labels

    3. Replace all damaged or missing labels. To order new labels go to your Land Pride dealer. 4. Some new equipment installed during repair require safety labels to be affixed to the replaced component as specified by Land Pride. When ordering new components make sure 03/11/03 Wear Protective Equipment Protective clothing and equipment should be worn.
  • Page 6 Z52®, Z60® & Z72® Zero Turning Radius Mowers Accu-Z 356-005M 19097 838-305C 19098 Warning: Rollover Hazard (Beneath Bumper on Back of Frame) 838-306C Warning: Do not operate without deflector 818-543C 19097 Danger: Guard is missing (Beneath foot pan on mower deck) Land Pride 838-303C Danger: Battery (Beneath Seat) 03/11/03...
  • Page 7 Land Pride Important Safety Information 03/11/03 19057 19057 19097 19057 Z52®, Z60® & Z72® Zero Turning Radius Mowers Accu-Z 356-005M 838-307C Warning: Moving Parts (Both Sides) 838-308C Warning: Rotating Blade Hazard (Both Sides) 838-310C Warning: General 838-399C Warning: Fuel Imbedded in Fuel Tank...
  • Page 8: Introduction

    To order a new Operator or Parts Manual contact your authorized dealer. Manuals can also be downloaded, free-of-charge from our website at www.landpride.com or printed by your dealer from the Land Pride Service & Support Center CD-Rom. Terminology: “Right” or “Left” as used in this manual is determined by facing the direction the machine will operate while in use unless otherwise stated.
  • Page 9: Section 1 Assembly And Set-Up

    Land Pride Section 1 Assembly and Set-Up Section 1 Assembly and Set-Up Control Lever and Seat Assembly The seat is removed for ease in shipping and the control lever’s upper bolts and flat washers are removed and the levers are rotated down.
  • Page 10: Optional Equipment Assemblies

    Control Lever Extensions Refer to Figure 1-5: 1. Install the Extensions (#4) as shown. Z52®, Z60® & Z72® Zero Turning Radius Mowers Accu-Z 356-005M Figure 1-4 Air Cleaner 19121 Control Lever Assembly Figure 1-5 Land Pride 5/16” Bolt Hose Clamp 20860 03/11/03...
  • Page 11: Accu-Vac Assembly

    Section 1 Assembly and Set-Up Accu-Vac Assembly Refer to Figure 1-9 on page 12 Land Pride offers as an option an Accu-Vac Collection System designed to collect mower clippings into two 30 gallon rubber containers mounted on the back of the mower.
  • Page 12: Blower, Pulley And Pulley Cover Assembly

    6. Install blower belt (#16) to double pulley and route it as shown. (Belt must be on top pulley) Blower Drive Belt 7. Assemble pulley cover (#17) using existing knobs (#18). Route Belt to Top Pulley Land Pride 20855 Blower Belt 03/11/03...
  • Page 13: Bagger Assembly

    Land Pride Section 1 Assembly and Set-Up Bagger Assembly Refer to Figure 1-8: NOTE: Accu-Vac Collection System cannot be mounted on Accu-Z mowers manufactured with Honda engines. Use only with Kawasaki engines. 1. Remove and retain rear bumper bolts (#3) and flat washers (#4).
  • Page 14: Front Lift And Weight Assembly

    Z52®, Z60® & Z72® Zero Turning Radius Mowers Accu-Z 356-005M NOTE: Lubricant can be used when installing tube to bagger so the tube will slide over bagger inlet easier. Front Lift and Weight Assembly Figure 1-10 Land Pride 19911 Z52 Left Side 19909 03/11/03...
  • Page 15: Section 2 Operation

    Land Pride Section 2 Operation Section 2 Operation 19058 5. Deck Lift Pedal 1. Ignition Switch 6. Hour Meter 2. Throttle Lever 7. Oil Pressure Light 3. Control Levers 8. Fuel Tanks 4. Blade Engagement Switch 9. Hydraulic Reservoir Controls For general location of the controls described in this section, refer to Figure 2-1.
  • Page 16: Parking Brake

    Push the deck lift pedal to raise the deck when going over obstructions. Deck Height Locking Pin 19698 Deck Lift Pedal Figure 2-6 Land Pride 19060 Deck Lift Pedal 19061 03/11/03...
  • Page 17: Instrumentation

    If the seat switch is not operating properly and if the cause can not be determined, replace the seat switch. If the problem can not be located, contact your Land Pride Dealer. WARNING! The safety interlock system should always function per steps 4 and 5.
  • Page 18: Moving Mower With Stalled Engine

    IMPORTANT: Always make certain the two bypass valves are returned to their operating position before running the mower following repairs. Forward Travel Reverse Travel Right Turn Right Turn Steering Figure 2-9 Land Pride 19064 Reverse Travel 03/11/03...
  • Page 19: Driving The Mower

    Land Pride Section 2 Operation Driving the Mower DANGER! Never make sudden stops or reverse direction, especially when going down a slope. The steering is designed for sensitive response. Rapid movement of the control levers in either direction could result in a reaction of the mower that can cause serious injury.
  • Page 20: Mower Deck Operation

    NOTE: Engaging the blade engagement switch at high engine rpm or when under heavy load (in tall grass for example) can cause belts to slip, resulting in premature wear or possible damage. Blade Engagement Switch 19065 19059 Blade Engagement Switch Figure 2-11 Land Pride 03/11/03...
  • Page 21: Operating Instructions

    Land Pride Section 2 Operation Operating Instructions After thoroughly familiarizing yourself with the Operator’s Manual and completing the Operator’s Checklist, you are almost ready to begin mowing. Approach the mower from the front and make sure the steering levers are spread fully apart in parking brake position.
  • Page 22: Section 3 Adjustments

    Some repairs require the assistance of a trained service mechanic and should not be attempted by unskilled personnel. Consult your Land Pride service center when assistance is needed. Torque Values WARNING! Particular attention must be given to tightening the drive wheel lug nuts and wheel motor nuts.
  • Page 23: Control Lever Neutral Adjustment

    Land Pride Section 3 Adjustments Control Lever Neutral Adjustment Before considering any adjustment, check the tire air pressure and make certain hydraulic system oil is at operating temperature. Unequal tire pressure will cause the mower to drift to one side. Refer to “Tire Inflation Chart”...
  • Page 24: Control Lever Stops

    4. Check the length of the reverse spring when the control lever is in the neutral position. This dimension should be 1 7/8”. If it is not, adjust the lower nylock nut until the dimension is achieved. 5. Repeat for other side. Land Pride 03/11/03...
  • Page 25: Steering Dampener

    Land Pride Section 3 Adjustments Steering Dampener Refer to Figure 3-5: The steering dampeners are incorporated into the unit to provide some resistance when the control levers are moving forward or rearward. To set the steering dampeners in the correct operating position follow these steps: 1.
  • Page 26 However, if no brake resistance is noticed, the brake needs adjusted as follows: 7. Loosen the brake linkage jam nuts. Refer to Figure 3-10. Jam Nut Brake Linkage Loosen Brake Linkage Jam Nut Figure 3-10 Land Pride Travel Slot 19084 Jam Nut Turnbuckle 19085 03/11/03...
  • Page 27: Hydraulic Pump Belt Adjustment

    Land Pride Section 3 Adjustments 8. Rotate the tire and at the same time rotate the turnbuckle to shorten the length of the brake linkage to increase the brake pressure. When you feel the brake begin to engage, stop adjusting the turnbuckle. Re- tighten the jam nuts on the turnbuckle.
  • Page 28: Deck Level Adjustment

    Loosen all nuts on the deck lift threaded rods, and the hardware on the adjuster (on the right front), until all the deck lift chains are loose, and the deck is sitting tightly on all four blocks. Blocks 19088 Land Pride Height Adjusting Stop 19089 Cutting Height Figure 3-15...
  • Page 29 Land Pride Section 3 Adjustments threaded Rod Chain Deck Level Adjustment Figure 3-17 5/16” Bolt Adjuster Hardware Deck Level Adjustment Figure 3-18 7. Loosen the two nuts on the front of height indicator so that the foot pedal is free. Refer to Figure 3-19.
  • Page 30: Deck Cutting Height Adjustment

    1”, 1 1/2”, 2”, 2 1/2”, 3”, 3 1/2”, 4”, 4 1/2” or 5”. The notch located at the rear of the right height adjusting bar is to used when the deck is placed in the transport mode. Land Pride Stop 19089 03/11/03...
  • Page 31: Anti-Scalp Rollers

    Land Pride Section 3 Adjustments Anti-Scalp Rollers Anti-scalp rollers are standard on the Accu Z. These anti- scalp rollers are designed to minimize scalping when mowing on rough uneven terrain. After setting the cutting height, adjust the front anti-scalp rollers so they extend below the deck but do not contact the ground.
  • Page 32: Section 4 Maintenance And Lubrication

    Top View Deck Top View Z52®, Z60® & Z72® Zero Turning Radius Mowers Accu-Z 356-005M Maintenance Locations Figure 4-1 Land Pride 1. Engine Oil Fill & Dipstick 2. Fuel Filter 3. Donaldson Engine Air Cleaner 4. Engine Oil Drain Plug 5.
  • Page 33: Maintenance Schedule

    Land Pride Section 4 Maintenance and Lubrication Service at Intervals Indicated Verify Safety Start Interlock System Visually Inspect Unit for loose hardware and/or damaged parts Visually Inspect Tires Check Oil Level, Engine (1) Clean Air Intake Screen Check Fuel Level Blades - Sharpen &...
  • Page 34: Maintenance

    Some repairs require the assistance of a trained service mechanic and should not be attempted by unskilled personnel. Consult your Land Pride dealer when assistance is needed. Torque Values WARNING! Particular attention must be given to tightening the drive wheel lug nuts, wheel motor nuts, and blade spindle nuts.
  • Page 35: Hour Meter

    Land Pride Section 4 Maintenance and Lubrication Hour Meter To recognize when your machine needs servicing, check the hour meter and the maintenance schedule. The hour meter shows the number of hours the engine has run and the maintenance schedule lists the service intervals. See Figure 4-2.
  • Page 36: Access To Engine And Hydraulic Pumps

    Fluid level should be 1” from top of reservoir. Use only SAE 10W40 SG, SF/CC, CD service motor oil. Change hydraulic system filter element (Land Pride P/N 831-030C) (Fig. 4-5) after first 50 hours of mower operation, then replace filter and oil in reservoir every 500 hours thereafter.
  • Page 37: Fuel System

    Land Pride Section 4 Maintenance and Lubrication 1. Fill the filter element with clean system oil. Smear a light coating of oil on upper surface of rubber seal. 2. Install the filter element on base. Tighten the oil filter by hand until the filter seal makes contact with the filter head, then tighten an additional 3/4”...
  • Page 38: Engine Air Filter

    Dust must not leak past the seals on each end of the air filter element. The filter must be aligned within the canister and properly seated for an effective seal so that no dirt can enter the engine. Land Pride 03/11/03...
  • Page 39: Damaged Filter, Seals Or Canister

    Use only the correct Donaldson air filter element, Land Pride part number 839-312C, which is designed to fit the canister properly. Land Pride air filter elements have the correct media composition, filter area, micron size and dimensions. Always use genuine Land Pride filters. Many aftermarket filters have been found to be incompatible with Land Pride’s canisters and engines.
  • Page 40: Belt Replacement

    Mower Blade Maintenance Lift Jack Option For easier blade maintenance a lift jack can be purchased from your Land Pride Dealer and easily assembled to your mower. Refer to Figure 4-12. Lift Jack 19912 Figure 4-12 Check the mower blades daily, they are the key to power efficiency and well groomed turf.
  • Page 41: Storage

    1. Remove all grass, dirt, and trash. Clean and touch up all scrapes with Land Pride spray paint. 2. Clean paper air filter. Replace if necessary. Wash and re-oil foam pre-cleaner.
  • Page 42: Section 5 Specifications And Capacities

    37.5 FT. LBS @ 2500 RPM 1.8 US quarts 39” 76" 60" 72" 65" 82 1/2" 1,100 lbs. 1,230 lbs. 24 x 12.00 - 12, turf tread 53" Electronic Mechanical 12 US GAL 10W40 motor oil Reverse: 0-5 MPH Land Pride 03/11/03...
  • Page 43 Land Pride Section 5 Specifications and Capacities Parking Mower Drive Safety Features Seat Cup Holder Hand Operated Controls Indicators Cutting Heights Mowing Blades Blade Tip Speed Blade Drive Spindles Flotation Mainframe Construction Drive motor mount Caster wheels Front caster forks...
  • Page 44: Section 6 Features And Benefits

    For extra comfort for the larger person. Add the extensions to give more leg room. Deck has a spring assisted chain suspension which offers excellent flotation over uneven terrain. Height is changed by a spring-loaded foot operated lever and pin. Easy to push and faster than waiting on an electric actuation. Land Pride 03/11/03...
  • Page 45: Section 7 Troubleshooting

    Land Pride Section 7 Troubleshooting Section 7 Troubleshooting Symptoms Starting motor does not crank Engine cranks but does not start Engine: Runs with continuous misfiring or engine runs unevenly or erratically Loss of power or system will not operate in either direction...
  • Page 46: Section 8 Appendix

    4290 3160 ft-lb= foot pounds 2190 4820 3560 mm x pitch = nominal thread dia. in millimeters x thread pitch Inflation PSI Land Pride Bolt Head Identification 10.9 Class 5.8 Class 8.8 Class 10.9 N · m ft-lb N · m ft-lb N ·...
  • Page 47: Warranty Statement

    Belts, blades, and tires are considered wear items. Filters and Plugs are considered maintenance items. This Warranty is limited to the replacement of any defective part by Land Pride and the installation by the dealer of any such replacement part, and does not cover common wear items such as blades, belts, tines, etc.
  • Page 48 Corporate Office: P.O. Box 5060 Salina, Kansas 67402-5060 USA www.landpride.com...

This manual is also suitable for:

Accu-z z60

Table of Contents