FCC ID: OMOTX29UTH (transmitter)
RF Exposure mobile:
The internal / external antennas used for this mobile transmitter
must provide a separation distance of at least 20 cm (8 inches)
from all persons and must not be co-located or operating in
conjunction with any other antenna or transmitter."
Statement according to FCC part 15.19:
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept
any interference received, including interference that may
cause undesired operation.
Statement according to FCC part 15.21:
Modifications not expressly approved by this company could
void the user's authority to operate the equipment.
Statement according to FCC part 15.105:
NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more
of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and
receiver.
•
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for
help
TABLE OF CONTENTS
Topic
Page
Introduction
3
Inventory of Contents
4
Quick Set Up
4
Detailed Set Up
6
Battery Installation
6
12 or 24 Hour Time Display
8
Time Setting
9
Features
10
Minimum & Maximum Temperature
and Humidity
10
Resetting Minimum & Maximum
12 or 24 Hour
Temperature and Humidity
10
Time Display
Adding Additional Thermo-Hygro
Indoor
Sensors
11
Temperature
Viewing & Operating with Multiple
(˚F or ˚C)
Thermo-Hygro Sensors
13
Connection w/
Mounting
13
Sensor Icon
Troubleshooting
17
Low Battery
Maintenance & Care Instructions
18
Indicator
Specifications
18
Warranty Information
19
Set/Channel
Button
GB
P.2
Figure 1
WS-7220U-IT
915 MHz
Wireless Weather Station
Instruction Manual
This product offers:
I N S T A N T
TRANSMISSION
is the state-of-the-
art new wireless
transmission technology, exclusively
designed and developed by LA CROSSE
TECHNOLOGY. INSTANT TRANSMISSION
offers you can an immediate update (every 4
seconds!) of all your outdoor data measured
from the transmitters: follow your climatic
variations in real-time!
Outdoor
Temperature
(˚F or ˚C)
Outdoor
Humidity
(%RH)
Minimum/
Maximum &
Plus Button
P.3
GB
Contents
Language
English
French
Spanish
1. Have the Wireless Weather Station and
2. Batteries should be out of both units for 10
Wireless
Thermo-hygro
3. Place the batteries into the thermo-hygro
Sensor
TX29UD-TH-IT
4. DO NOT PRESS ANY BUTTONS FOR 15
In this time the Wireless Weather Station and
Mounting
the ther mo-hygro sensor will begin to
Bracket
Figure 2
communicate with each other, and the display
will show both the indoor temperature and an
INVENTORY OF CONTENTS
outdoor temperature. If the Wireless Weather
1. Wireless Weather Station (Figure 1)
Station does not display both temperatures after
2. Wireless Thermo-Hygro Sensor (TX29UD-TH-
the 15 minutes, please retry the set up as stated
IT) and mounting bracket. (Figure 2)
above.
3. 3 each, 1/2" Philips screws.
temperatures are displayed for 15 minutes you
4. One strip of double sided adhesive tape.
can place your thermo-hygro sensor outdoors,
5. Instruction Manual and Warranty Card.
and set your time.
ADDITIONAL EQUIPMENT
The thermo-hygro sensor should be placed in a
(not included)
dry, shaded area (ex: under the eve of a roof).
1. 1 Philips screwdriver.
The thermo-hygro sensor has a range of 330
2. 2 Fresh "AA" 1.5V Alkaline Batteries.
feet. Any walls that the signal will have to pass
3. 2 Fresh "AAA" 1.5V Alkaline Batteries.
through will reduce distance. An outdoor wall
or window will have up to 20 feet of resistance
QUICK SETUP
and an interior wall will have up to 10 feet of
Hint: Use good quality Alkaline Batteries; avoid
resistance. Your distance plus resistance should
rechargeable batteries.
not exceed 330 feet in a straight line.
NOTE: Fog and mist will not harm your thermo-
GB
P.4
Page
2
24
48
thermo-hygro sensor 3 to 5 feet apart.
minutes.
sensor first and next into the Wireless
Weather Station.
MINUTES.
After both indoor and outdoor
P.5
GB