La Crosse Technology WS-8055U Instruction Manual

La Crosse Technology WS-8055U Instruction Manual

Radio controlled moon phase clock

Advertisement

WS-8055U
Radio Controlled Moon Phase Clock
Instruction Manual

Advertisement

Table of Contents
loading

Summary of Contents for La Crosse Technology WS-8055U

  • Page 1 WS-8055U Radio Controlled Moon Phase Clock Instruction Manual...
  • Page 2: Table Of Contents

    TABLE OF CONTENTS Topic Inventory of Contents/ Additional Equipment About WWVB Quick Set-Up Guide Detailed Set-Up Guide Battery Installation Program Mode Function Buttons Time Zone Setting DST (Daylight Saving Time) Setting Language Selection Time Setting Calendar Setting 12/24-Hour Setting Selecting °F or °C Features &...
  • Page 3: Inventory Of Contents/ Additional Equipment

    2) Wait 10 minutes for WWVB reception. 3) If there is no WWVB reception, manually set the time and date (instructions in the Program Mode). 4) Program the settings. 5) Place the WS-8055U in a suitable location, where WWVB signals can be received.
  • Page 4: Detailed Set-Up Guide

    DETAILED SET-UP GUIDE BATTERY INSTALLATION Note: To avoid start-up problems make sure that the batteries do not spring free. A) MOON PHASE CLOCK 1) Remove the battery cover, located on the backside of the unit. 2) Observe the correct polarity, and install 2 AA batteries.
  • Page 5: Program Mode

    PROGRAM MODE To enter the Program Mode hold down the “SET” button for 2 seconds, until “-5EST” flashes in the Date LCD. The Program Mode is laid out in a manner that allows you to program each function separately, or you can follow the instructions entirely to program the Moon Phase Clock.
  • Page 6: Dst (Daylight Saving Time) Setting

    III) DST (DAYLIGHT SAVING TIME) SETTING Note: The DST default is “On”, meaning that the WWVB will automatically change the time according to Daylight Saving Time in the spring and fall. For areas that do not recognize DST changes (Arizona and parts of Indiana) turn the DST “OFF”. 1) Hold down the “SET”...
  • Page 7: Calendar Setting

    VI) CALENDAR SETTING Note: When the WWVB signal is found, that date will over-ride the manually set date. 1) Hold down the “SET” button for 2 seconds (the selected time zone will flash), press the “SET” button 5 more times, until the default year “00” flashes in the date LCD.
  • Page 8: Features & Operations

    FEATURES & OPERATIONS CHANGING DISPLAY MODE (DAY, SECONDS, AND TEMPERATURE) There are three possible display modes to view the day, seconds, and temperature. The month&date/weekday/moon phase/indoor temperature is the default. To change the display: 1) Press the “+” button. The display should now show the month&date/weekday/moon phase/seconds.
  • Page 9: Mounting

    C) ACTIVATING THE SNOOZE FUNCTION 1) While the alarm is sounding, press the “SNOOZE” button to activate the snooze function. The alarm “sound” icon and “SNOOZE” icon (to the right of the time) will flash. The duration of the snooze function is 10 minutes, then the alarm will resume.
  • Page 10: Maintenance & Care

    2) Check batteries. 3) Read “moon phase” section in manual Note: For any questions not answered, contact La Crosse Technology with the contact information found at the end of this instructional manual. Alarm in the general direction of Ft. Collins, Colorado.
  • Page 11: Specifications

    La Crosse Technology immediately upon discovery of any defects covered by this warranty. Before sending the Moon Phase Alarm in for repairs, contact La Crosse Technology. The Moon Phase Alarm will be repaired or replaced with the same or similar model.
  • Page 12 We accept no liability for technical mistakes or printing errors, or their consequences. All trademarks and patents are acknowledged. La Crosse Technology, Ltd 2809 Losey Blvd. S. La Crosse, WI 54601 Phone: 608.782.1610...

Table of Contents