Table of Contents
Advertisement
4-1/2 inch (114mm) Cut Off Tool / Grinder
Meuleuse d'angle de 4-1/2 po. (114mm)*
Esmeriladora angular de 114mm (4-1/2 pulg.)
www.portercable.com
INSTRUCTIVO DE OPERACIÓN, CENTROS DE
SERVICIO Y PÓLIZA DE GARANTÍA.
ADVERTENCIA:
ANTES DE USAR EL PRODUCTO.
LÉASE ESTE INSTRUCTIVO
Instruction manual
Manuel d'instructions
Manual de'instrucciones
CATALOG NUMBER
N° de catalogue
catálogo N°
PC60TAG
PC60TCTAG
Advertisement
Table of Contents
Related Manuals for Porter-Cable PC60TAG
Summary of Contents for Porter-Cable PC60TAG
- Page 1 Esmeriladora angular de 114mm (4-1/2 pulg.) Instruction manual Manuel d’instructions Manual de’instrucciones www.portercable.com CATALOG NUMBER N° de catalogue catálogo N° INSTRUCTIVO DE OPERACIÓN, CENTROS DE PC60TAG SERVICIO Y PÓLIZA DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO PC60TCTAG ANTES DE USAR EL PRODUCTO.
-
Page 2: Safety Guidelines - Definitions
SAFETY GUIDELINES - DEFINITIONS It is important for you to read and understand this manual. The information it contains relates to protecting YOUR SAFETY and PREVENTING PROBLEMS. The symbols below are used to help you recognize this information. DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. -
Page 3: Safety Instructions For All Operations
wire brush, or cut-off tool. Read g) If devices are provided for the all safety warnings, instructions, connection of dust extraction and illustrations and specifications collection facilities, ensure these are provided with this power tool. Failure connected and properly used. Use of to follow all instructions listed below dust collection can reduce dust-related may result in electric shock, fire and/or... -
Page 4: Kickback And Related Warnings
the work area must wear personal Kickback is a sudden reaction to a protective equipment. Fragments of pinched or snagged rotating wheel, workpiece or of a broken accessory backing pad, brush or any other may fly away and cause injury beyond accessory. -
Page 5: Safety Warnings Specific For Sanding Operations
other blind areas. The protruding exposed towards the operator. wheel may cut gas or water pipes, The guard helps to protect operator electrical wiring or objects that can from broken wheel fragments and cause kickback. accidental contact with wheel. g) It is recommended to use grinding/ c) wheels must be used only for cutting wheels no thicker than 1/4 recommended applications. - Page 6 California to cause cancer, birth defects Minimum Gauge for Cord Sets or other reproductive harm. Some Volts Total Length of Cord in Feet 120V 0-25 26-50 51-100 101-150 examples of these chemicals are: (0-7,6m) (7,6-15,2m) (15,2-30,4m) (30,4-45,7m) • lead from lead-based paints, Ampere Rating More Not more American Wire Gauge...
-
Page 7: Functional Description
27 and 29 require different accessory guards. A Type 1 guard is provided for use with a Type 1 wheel. PC60TAG is provided with a Type 27 grinding guard only. A Type 1 guard for use with cut off wheels is available separately at additional cost. -
Page 8: Operation
Both Type 27 and Type 1 guards attach and are removed in the same way as described below. 1. Figure B - Open the guard latch (7), and align the lugs on the guard (8) with the slots on the gear case cover (9). - Page 9 Wire Wheels 4-1/2 inch (115mm) Grinding Wheels Type 27 guard Type 27 guard Type 27 guard unthreaded 3 inch wire backing flange Type 27 hubbed wheel cup brush Type 27 depressed center wheel sanding Discs Type 27 guard threaded clamp nut rubber backing pad 4-1/2 inch (115mm) 4 inch wire...
- Page 10 ROTATING ThE GEAR CAsE (FIG. E) Turn off and unplug tool before making any adjustments or removing or installing accessories. Before reconnecting the tool, depress and release the trigger switch to ensure that the tool is off. 1. Remove guard and flanges from tool. 2.
- Page 11 MOUNTING NON-hUBBED WhEELs WARNING: To prevent accidental operation, turn off and unplug tool before performing the following operations. Failure to do this could result in serious personal injury. Depressed center Type 27 grinding wheels must be used with included flanges. See pages 9 and 10 of this manual for more information.
- Page 12 sURFACE GRINDING WITh GRINDING WhEELs 1. Allow the tool to reach full speed before touching the tool to the work surface. 2. Apply minimum pressure to the work surface, allowing the tool 20˚-30˚ to operate at high speed. Grinding rate is greatest when the tool operates at high speed.
-
Page 13: Environmental Safety
2. Place the sanding disc (15) on the backing pad (14). 3. While depressing spindle lock, thread clamp nut (13) on spindle, piloting the raised hub on the clamp nut into the center of san ding disc and backing pad. 4. -
Page 14: Cleaning And Disposal
CLEANING AND DIsPOsAL 1. All surfaces in the work area should be vacuumed and thoroughly cleaned daily for the duration of the sanding project. Vacuum filter bags should be changed frequently. 2. Plastic drop cloths should be gathered up and disposed of along with any dust chips or other removal debris. - Page 15 and concrete use are available. Diamond blades for concrete cutting can also be used. WARNING: A closed, 2-sided cutting wheel guard is re quired when using cutting wheels. Fail ure to use proper flange and guard can re sult in injury resulting from wheel breakage and wheel contact.
-
Page 16: Maintenance
Maintenance CLEANING WARNING: Blowing dust and grit out of the motor housing using compressed air is a necessary maintenance procedure. Dust and grit from metal grinding often accumulate on interior surfaces and could create an electrical shock hazard if not cleaned out. -
Page 17: Service And Repairs
sERvICE AND REPAIRs All quality tools will eventually require servicing and/or replacement of parts. For information about Porter Cable, its factory service centers or authorized warranty service centers, visit our website at www.portercable.com or call our Customer Care Center at (888) 848-5175. All repairs made by our service centers are fully guaranteed against defective material and workmanship. - Page 18 The following are PORTER CABLE trademarks for one or more power tools and accessories: a gray and black color scheme; a “four point star” design; and three contrasting/outlined longitudinal stripes. The following are also trademarks for one or more Porter Cable and Delta products: 2 BY 4®, 890™, Air America®, AIRBOSS™, Auto-Set®, B.O.S.S.®, Bammer®, Biesemeyer®, Builders Saw®, Charge Air®, Charge Air Pro®, CONTRACTOR SUPERDUTY®, Contractor’s Saw®, Delta®, DELTA®, Delta Industrial®, DELTA MACHINERY &...