American Dynamics SpeedDome RASEL Series Installation And Service Manual

Speeddome optima lt indoor camera dome

Advertisement

Quick Links

SpeedDome
Optima LT Indoor
Camera Dome
RASEL Series

Installation and Service Guide

The SpeedDome Optima LT indoor camera dome
mounts either to a hard ceiling or to a 2x2 tile
ceiling using a mounting plate (instructions for the
plate are supplied separately).
CAUTION: Save the box and packing
!
materials. These materials are required
should you need to ship the dome to a
repair center.
Note: The dome accepts either cable or conduit. If
running cable through a plenum ceiling, either
plenum-rated cable or flexible conduit is required.
© Sensormatic 2003
SPEEDDOME OPTIMA LT INDOOR CAMERA DOME INSTALLATION AND SERVICE GUIDE (8200-0181-01, REV. C)
®
Contents
Warnings ............................................................2
Before You Begin ...............................................3
Installation ..........................................................6
Troubleshooting .................................................9
Parts List for Authorized Users ........................10
Specifications ...................................................12
Declarations .....................................................14

Customer Support

If you need assistance, contact your sales
representative.
1 of 14

Advertisement

Table of Contents
loading

Summary of Contents for American Dynamics SpeedDome RASEL Series

  • Page 1: Table Of Contents

    SpeedDome Contents ® Warnings ............2 Optima LT Indoor Before You Begin ..........3 Installation ............6 Camera Dome Troubleshooting ..........9 Parts List for Authorized Users ......10 Specifications ...........12 RASEL Series Declarations .............14 Installation and Service Guide Customer Support If you need assistance, contact your sales representative.
  • Page 2: Warnings

    EU power requirements: This product runs on Warnings 24Vac. In the EU, it is intended to be powered from a Limited Power Source. A limited power source is Please review the following warnings before you a certified source of SELV, and if inherently limited, install or service the camera dome.
  • Page 3: Before You Begin

    Data cable requirements Before You Begin SensorNet Manchester To ensure a smooth and successful installation, Cable type observe the following requirements. unshielded, shielded twisted twisted General Requirements pair* pair** Wire gauge 22 AWG 18 AWG · Have electrical work comply with latest national electrical code, national fire code, and all Non- Connection...
  • Page 4 80 (250) end of the cable. The figure below shows twisted pair cable connections. See installation guide 8200-0298-01 for details. Twisted Pair Adapter (Dome End) American Dynamics Dome Or Fixed Camera Twisted Pair Adapter (Fixed Camera End) Cat 2-6 UTP Cable...
  • Page 5: Setting The Camera Address

    SensorNet/Manchester Line Termination Power-Up Routine SensorNet and Manchester communication After power is connected to the dome, the dome protocols require that the dome furthest from the performs a homing routine. During the homing video controller or junction box be terminated. process, the camera will pan and then either: Looking through the hole in the top of the dome, ·...
  • Page 6: Installation

    3. To expose connectors and settings at the top Installation of the dome, remove the cover plate by removing one screw and loosening the other. 24Vac (P10) Address Switches Parts required Set the camera address. As an example, address 107 is shown. Note: For installation to a tile ceiling, also order the SW3 SW2 SW1 x100...
  • Page 7 12. Attach a BNC connector to the video cable (if 15. Using safety wire, attach the dome to a strong not using the Twisted Pair Adapter). Also structural ceiling member as follows: attach the orange 3-pin power plug to a. Find a strong structural member capable of connector P10 and the gray 2-pin data supporting the dome.
  • Page 8 16. Insert the dome into the hole in the ceiling. 19. Once the homing routine completes, affix the bubble to the dome as follows: a. Place the large hole at the end of the lanyard over the screw head of the bubble and pull its end to snap it in place.
  • Page 9: Troubleshooting

    Pan control absent or improper, but other Troubleshooting control OK. Send the dome to a repair center. If a failure cannot be easily fixed, send the dome to a repair center. Tilt control absent or improper, but other No power (no LEDs light). control OK.
  • Page 10: Parts List For Authorized Users

    General Parts List for Chassis Assembly, NTSC 0101-0013-01 Authorized Users Chassis Assembly, PAL 0101-0013-02 The following parts can only be ordered by Housing Assembly 0404-0009-01 authorized users. To become authorized, contact your sales representative. Install Kit 0352-0020-01 Bubble Assembly, Clear 0100-2458-01 Bubble Assembly, Smoked 0100-2458-02...
  • Page 11 10,11 Tilt Assy. 0400-1207-01/-02 Base Assy. 0404-0008-01 SPEEDDOME OPTIMA LT INDOOR CAMERA DOME INSTALLATION AND SERVICE GUIDE (8200-0181-01, REV. C) 11 of 14...
  • Page 12: Specifications

    White balance......Through the Lens (TTL) Specifications Automatic Tracing White Balance (ATW) NTSC version: Operation Pickup device ....768 (H) x 494 (V) pixels Manual pan speed....1–50° per second Scanning ......525 lines, 60 fields, Target pan speed....100° per second max. 30 frames Pan travel.......
  • Page 13: Electrical Specifications

    Electrical Specifications SensorNet Communications Power Line Address range ......0 to 255 Bit rate: ........230.4Kbps Input voltage ......18–30Vac, Class 2 Limited Power Source Network distance ....1km Design tolerance ....16–36Vac Maximum loads ...... 32 per node Line frequency ....... 50/60Hz Node repeaters.......
  • Page 14: Declarations

    Mechanical Specifications Other Declarations Camera Dome Thank you for using American Dynamics products. We support our products through an extensive and worldwide Housing diameter....190mm (7.5in) network of dealers. The dealer, through whom you originally purchased this product, is your point of contact if you have a Housing height need for service or support.

Table of Contents