Provisiones especiales: Disposizioni speciali: Representative in the Union: Patrick Vervier, Stanley Dubuis 17-19, rue Jules Berthonneau-BP 3406 41034 Blois Cedex, France. Vertreter in der Union/Représentant dans l’union/Representante en la Union/Rappresentante presso l’Unione Done at/Ort/Fait à/Dado en/Fatto a Stanley Hydraulic Tools, Milwaukie, Oregon USA...
REPAIRS AND / OR SERVICE TO THIS TOOL MUST ONLY BE DONE BY AN AUTHORIZED AND CERTIFIED DEALER. For the nearest authorized and certified dealer, call Stanley Hydraulic Tools at the number listed on the back of this manual and ask for a Customer Service Representative.
Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULATIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte- nance personnel. 4 ► GR30 User Manual...
• Do not tighten or loosen the wheel nut by impact. The GR30 Hydraulic Grinder will provide safe and de- Hold the shaft with a second wrench on the the flats pendable service if operated in accordance with the in- behind the wheel and tighten securely.
Page 6
Do not allow other persons near the tool when start- ing or cutting. • Any use of this tool outside those stated in this man- ual are forbidden. • Never operate the tool when you are tired or fa- tigued. 6 ► GR30 User Manual...
OPERATION MANUAL. OPERATION MANUAL. TAG TO BE REMOVED ONLY BY TAG TO BE REMOVED ONLY BY TOOL OPERATOR. TOOL OPERATOR. SEE OTHER SIDE SEE OTHER SIDE SAFETY TAG P/N 15875 (shown smaller then actual size) GR30 User Manual ◄ 7...
HOSE SAFETY TAGS To help ensure your safety, the following DANGER tags are attached to all hose purchased from Stanley Hydraulic Tools. DO NOT REMOVE THESE TAGS.
2000 psi 2000 psi 2000 psi (at the power supply outlet) (172 bar) (138 bar) (138 bar) (138 bar) (138 bar) NOTE: These are general hydraulic system requirements. See tool specification page for tool specific requirements 10 ► GR30 User Manual...
PRE-OPERATION PROCEDURES 4. Check the grinding wheel: a. Make sure the correct wheel is selected for the The GR30 Hydraulic Grinder Requires minimum setup job. The wheel must conform to the specifica- for operation. When the installation and operation in- tions listed in this manual.
Page 12
Make sure the grinder stops when the trigger is the tool. released. 4. The tool should be clean, with all fittings and fasten- ers tight. 12 ► GR30 User Manual...
Page 13
The oil should be at or above 50 °F/10 °C with a viscos- of the body. ity of 400 SSU/82 cs before operating the tool. GR30 User Manual ◄ 13...
(supply) hose, then the output (return) hose. 3. Place dust plugs on the couplers, as applicable. 4. Wipe the tool thoroughly with a clean dry cloth. 5. Clean any foreign matter from the grinding wheel surfaces. 14 ► GR30 User Manual...
This can cause damage to internal seals. • Always replace hoses, couplings and other parts with replacement parts recommended by Stanley Hydraulic Tools. Supply hoses must have a mini- mum working pressure rating of 2500 psi/172 bar. GR30 User Manual ◄ 15...
If a situation occurs that is not chart can be used as a guide to correct the problem. covered, call your Stanley Customer Service represen- When diagnosing faults in operation of the tool, always tative for assistance.
Page 17
Porting spool incorrectly installed. Contact your authorized Stanley dis- stop after release of trigger. tributor. Mechanical failure. Contact your authorized Stanley dis- tributor. * Grinding wheel should rotate CCW when viewed from the shaft end. GR30 User Manual ◄ 17...
Weight (with Wheel Guard) ........................10 lbs/4.5 kg Length..............................8 in/20.3 cm Width ..............................10 in/25/4 cm This tool is for land use only. Contact your authorized Stanley distributor for information about the GR29 underwater model. SOUND POWER AND VIBRATION DECLARATION Test conducted on GR3070101, operated at 8 gpm input Measured A-weighted sound power level, Lwa (ref.