Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Simrad BSM-3
Summary of Contents for Simrad BSM-3
- Page 1 BSM-3 Installation Manual ENGLISH simrad-yachting.com...
- Page 3 NMEA 2000 is a registered trademark of the National Marine Electronics Association. Navionics is a registered trademark of Navionics SpA. Simrad is a trademark of Kongsberg Maritime AS Company registered in the US and other countries and is being used under license.
- Page 4 Reorient or relocate the receiving antenna • Increase the separation between the equipment and receiver • Connect the equipment into an outlet on a circuit different from that of the receiver • Consult the dealer or an experienced technician for help. BSM-3 Installation Manual...
-
Page 5: About This Manual
About this manual This document describes how to install the BSM-3 and connect the unit to transducers and display units. Separate installation instruction for transducers are included with the transducer package. The BSM-3 is compatible with the following MFD displays and systems: •... -
Page 6: Table Of Contents
Introduction BSM-3 module layout Parts included in package Installation and wiring Mounting location Securing BSM-3 module Wiring Connecting the BSM-3 to your display Transducer connection BSM-3 connectors Transducer with a 7-pin connector Transducer with bare wires Airmar transducers Trouble shooting... -
Page 7: Introduction
Introduction BSM-3 module layout ethernet connector GroundinG screW led status indicators removable cover connectors Parts included in package For spare parts and part numbers, see“Spare parts and accessories” on page 22. Item No. Description BSM-3 sounder module Ethernet cable, 1.8 m (6 ft) Power cable (bare wires), 2 m (6.5 ft) - Page 8 Item No. Description Screws Spare Fuse kit including; 3A Fuses and fuse holders Warranty card This manual Required tools and supplies 2 mm (5/64”) Drill Drill Bit Screw driver Pencil Introduction | BSM-3 Installation Manual...
-
Page 9: Installation And Wiring
If possible, mount the unit close to the edges of a panel to minimize vibration. Do not run the transducer cabling near the BSM-3 power cables, any VHF antenna coax cables or any DC or AC power cables. Avoid placing Ethernet cables close to VHF antennas. -
Page 10: Securing Bsm-3 Module
Securing BSM-3 module Mount the BSM-3 on a vertical surface with the power and transducer cable connections exiting downwards. Fasten the BSM-3 by using the 4 stainless steel self tapping screws included with the unit. 10 | Installation and wiring |... -
Page 11: Wiring
The unit has no power key and will turn on when power is applied. When used in an NSE/NSS/NSO evo2 system, it is recommended to connect the BSM-3 to the Power control bus, and set display system to power control master. -
Page 12: Connecting The Bsm-3 To Your Display
Connecting the BSM-3 to your display The BSM-3 connects to your display system over an Ethernet network, either directly or via a Network Expansion Port. When connected to an NSO, the RJ45 to 5 pin cross-over Ethernet cable included with the NSO system must be used. -
Page 13: Transducer Connection
Cable gland for independent temperature input: Tied to Transducer 1 Transducer port 2 : 7 pin blue connector: Connect low frequency transducers Cable gland for independent temperature input: Tied to Transducer 2 | 13 Transducer connection | BSM-3 Installation Manual... -
Page 14: Transducer With A 7-Pin Connector
Most Airmar transducers as of 2014 are available with 7-pin blue connectors including dual channel transducers. These connect to the corresponding connectors on the BSM-3. Dual channel transducers will have two connectors and will be labeled. Transducer with bare wires Remove connectors Remove cover. -
Page 15: Airmar Transducers
Insert the gland housing in to the BSM-3 case and secure with nut. Pass the gland securing nut over the bare wires and along the cable. Pass the cable through the gland housing. Terminate the wires to the terminal blocks according to the terminal... - Page 16 Low freq. depth shield Black and white (or black) Low freq. negative Blue/white or yellow Low freq. positive * Dual transducer installation only TEMP HIGH TEMP LOW XDCR HIGH XDCR LOW SPEED 16 | Transducer connection | BSM-3 Installation Manual...
- Page 17 Setting up the transducers The BSM-3 is compatible with Airmar’s Transducer ID protocol. If you have an Airmar transducer that supports this feature, BSM-3 will read your transducer’s specification at start-up and automatically adjust the frequency and temperature settings. The transducer’s XID wire (orange) should be connected to the XDCR_ID_HIGH/LOW terminal in the TEMP HIGH/LOW connector as shown below.
-
Page 18: Trouble Shooting
On - Green Ethernet connected and ok Transducer not connected Flashing every 0.5 second - Initializing transmitter Green Trans- ducers Flashing every second - Searching for bottom signal Green On - Green System operational 18 | Trouble shooting | BSM-3 Installation Manual... -
Page 19: Technical Specification
40-60 kHz; 25-45 kHz Narrowband Frequencies Transceiver High: 200 kHz; 83 kHz Narrowband Frequencies Transceiver Low: 50 kHz; 38 kHz; 28 kHz Transmitter and Dual Broadband tuned receivers receiver type Dual tuned CHIRP transmitters | 19 Technical specification | BSM-3 Installation Manual... - Page 20 CHIRP, simultaneous with narrowband Zoom size Auto/manual x2, x3, x4, x5, x6, x7, x8 (user selectable) DC Voltage requirements Voltage 10.7–32 VDC (for 12 or 24 VDC systems) Interfaces Network Ethernet 10/100 20 | Technical specification | BSM-3 Installation Manual...
-
Page 21: Dimensional Drawings
Dimensional drawings 340 mm (13.38”) 320 mm (12.60”) | 21 Dimensional drawings | BSM-3 Installation Manual... -
Page 22: Spare Parts And Accessories
Ethernet cable yellow 5 Pin 15.2 m (50 ft) 000-10029-001 NEP-2 Network Expansion Port (Yellow connectors) Transducers For a full list of compatible transducers please refer to the transducer selection guide on http://www.simrad-yachting.com/transducerguide/ 22 | Spare parts and accessories | BSM-3 Installation Manual...