Sony RM-V202T Operating Instructions

3-264-085-11(1)
RM-V202T
Remote Commander
Operating Instructions
Mode d'emploi (au verso)
© 2004 Sony Corporation Printed in China
English
Notes on Batteries
Setting Up the Remote Commander
•Do not mix old batteries with new ones or mix different types
of batteries together.
About Presetting the Commander
•If the electrolyte inside the battery should leak, wipe the
The Commander is preset at the factory to operate Sony brand
contaminated area of the battery compartment with a cloth and
components. replace the old batteries with new ones. To prevent the
If you are using the Commander with a Sony component, you
electrolyte from leaking, remove the batteries when you plan
will not need to preset the Commander before you start using it.
not to use the Commander for a long period of time.
To set up the Commander to use with other (non-Sony)
manufacturers' components, or to use with a component that is
not preset at the factory, you will need to follow the instructions Setting the Code
in this manual to preset the Commander with the correct code
Follow steps 1 and 2 below for each component you plan to use
number for your component(s). (See the supplied "Component
with the Commander.
Code Numbers" table also.)
Step 1: Entering the Code Number
Component that can be preset Button Factory setting
1
See the supplied "Component Code numbers" table, and find
TV TV Sony TV
the three-digit code number for the desired component.
VCR/Satellite tuner/DVD/TV VCR Sony VHS VCR (VTR3)
If more than one code number is listed, use the number that is
SAT Sony satellite tuner listed first to complete the steps below.
For example, if you are setting up a Philips TV, you would
DVD Sony DVD player
use the code number 086.
Notes If your component is not listed, see "Searching for the Correct
Code."
•The Commander can be set up to operate only one component
per button – unless their code numbers happen to be the same. 2 S
While pressing the S (SET)
For example, you cannot set up the Commander to operate a
button, press the 1 button.
Sony TV and a Panasonic TV simultaneously (because they use
3 TV VCR SAT DVD
Press the button of the
different code numbers).
component that you want to
•You may not be able to operate even a Sony brand component
set up.
with the factory presetting. In such a case, follow the
procedure in "Setting the Code."
Note
On the VCR, SAT and DVD buttons, "VCR," "satellite tuner,"
Installing the Batteries and "DVD player" are assigned respectively at the factory.
But you can also assign other components on these buttons.
Before replacing the batteries, have new ones ready
For details, see "Changing the Component Type on the VCR,
beforehand.
SAT and DVD buttons."
Slide open the battery compartment and insert two size AA (R6)
4
Enter the component's code number.
0 8 6
batteries (not supplied).
For example, if you are entering the
Be sure to line up the + and – on the batteries with the + and –
code for a Philips TV, you would
on the battery compartment. Your Code Number
press -86.
1 2
5 Press and release the t button to store
the code number in the Commander's
memory.
6 Go to "Step 2: Checking if the Code Number Works" to finish
setting up.
If you press a wrong button in step 4
Press the 1 button while pressing the S (SET) button and then
When to replace the batteries go back to step 2.
Under normal conditions, batteries will last up to 6 months. If
the Commander does not operate properly, the batteries might
be worn out. Replace the batteries with new ones.
Notes
•Replace both batteries with new ones.
•Do not take more than 3 minutes to replace the batteries;
otherwise, your code number settings will be erased.
Step 2: Checking if the Code Number Works
Changing the Component Type on the
1 VCR, SAT and DVD buttons
Turn on the component you want to set up.
2 Aim the Remote Commander at the component and press a At the factory, "VCR" is assigned to the VCR button, "satellite
button to check if that button works. tuner" is assigned to the SAT button and "DVD player" to the
For example, press the 1 button to see if it works on your DVD button. By completing the following procedure, you can
component. change this setting so that you can assign any component to
these buttons.
3 Check that the other buttons of the Commander are operating
the corresponding functions of the component. 1 While pressing the S (SET) button, press the 1 button.
2 Press the VCR, SAT or DVD button.
You can write down the code number on the label inside the
battery compartment lid. 3 Press and release the x (stop) button.
4 Press and release one of the following buttons:
If the Commander Does not Seem to be 1 to assign a VCR
3 to assign a satellite tuner
Working...
• First, try repeating these setup procedures using the other 8 to assign a TV
- to assign a DVD
codes listed for your component (see the supplied
"Component Code Numbers" table).
5 Press and release the t button.
• If after trying all the codes listed for your component you still
6
Enter the component's code number by following steps 2 to 6
cannot get the Commander to work properly, try the search
of "Entering the Code Number," or steps 1to 6 of "Searching
method described in "Searching for the Correct Code."
for the Correct Code."
Searching for the Correct Code
Operating a Component
If you have tried all the code numbers listed for your component
and you still cannot get the Commander to work (or if your
1 Press the button of the desired TV VCR SAT DVD
component is not listed in the "Component Code Numbers"
component on the Commander.
table), try these steps.
2 Point the Commander directly at the component.
Before starting the Search function
3 Press the button for the function you want to use.
Set each component to the following status to enable the Search
See "Remote Button Descriptions" for complete descriptions of
function.
the buttons on the Commander.
TV: power-on
Other components: power-off
Notes on Using the Remote Commander
1
While pressing the S (SET) button, press the 1 button. Basically, use this Commander in the same way as the
Commanders supplied with your components.
2 On the Commander, press the button of the component that
•Using this Commander will not increase the functions of your
you want to set up.
components. The functions of the Commander are limited to
3 Press and release the PROGR+ button. Then press and release
the functions of the components themselves. For example, if
the 1 button. your TV does not have a MUTING function, the % button on
4 this Commander will not function with your TV.
Repeat step 3 until the correct code number is found.
•Some functions of the component may not work with this
Each time you press the PROGR+ button and then the 1
Commander.
button, a new code number will be transmitted.
Keep trying until your component operates as follows:
• TV: power-off
Setting a channel with a single
• Other components: power-on
button (Channel macro function)
• TV without a power switch: the Channel + function works.
Be patient as you do this; it could take as many as 120 tries You can program the Channel Macro function on any of the
before the correct code number is located.
buttons listed below (macro keys).
For example, instead of pressing 1, 2, and then ENT button to
5 When the correct code is found, press the t button to store
change the TV channel, you can perform these operations by
the code number in the Commander's memory.
pressing only the N button.
6 Check that the Commander is operating the other functions of
your component by pressing the corresponding buttons on
The macro keys are:
the Commander. If they seem to be working properly, you are N, m, M, x, X, and zREC.
done setting up the Commander. (During "TV" or "satellite tuner" operations only.)
If the component does not operate properly, repeat steps 1 to 5 The series of operations that can be programmed must consist of
and search for another code.
two to four sequential pressings of the - to 9 buttons or ENT
button.
If you still cannot get the Commander to work properly, see
"Troubleshooting." Note
The Channel Macro function may not work correctly for some
Note components.
Be sure to proceed to each next step in the above procedure
within 10 seconds; otherwise setting mode will be canceled. To program a series of operations
1 Press the desired component select button.
(You can select "TV" or "satellite tuner" only.)
2 While pressing the desired macro key, press the buttons
required for the operations in sequence.
For example, to program 1 t 2 t ENT on the N button,
hold down N first, press 1, 2, and ENT in sequence, and
then release N.
Notes
•Even if you try to program more than four operations and Remote Button Descriptions
press the corresponding buttons in step 2 above, only the first
four buttons that were pressed will be programmed.
General
•If you try to program only one operation on a macro key, the
S 1 To set up the
setting operation will be rejected.
TV VCR SAT DVD Commander, press S
•You can program the Channel Macro function for up to three
1 2 3 (SET) while pressing 1.
components only. To program a fourth component, first clear
5 2+: Volume up.
all macro keys for a component.
4 5 6
2–: Volume down.
•If you have programmed the Channel Macro function for TV
7 8 9
7 To mute the volume on
or satellite tuner operation, the button used as a macro key
1- 2-
0 the TV.
cannot be used for Fastext buttons. ENT
PROGR qa To turn on and off the
power of the selected
To change or clear a program
component.
When you want to change the setting, or if you are no longer
qs Component select
using a programmed operation, follow the procedure below to
buttons.
overwrite or clear the program.
To switch to the
1 Hold down the macro key that you want to change or clear. MENU GUIDE OK operations of each
component, press the
2 After waiting for about three seconds, press the new sequence
REC
button on which that
of buttons, or, to clear the program, press and release -, and
component is assigned.
then press and release ENT.
3 Release the macro key.
Note
Be sure to wait for about three seconds in step 2 above. While
z The number 5 button and the
you are holding down the macro key and waiting, the
programmed signals are transmitted; therefore, if you are PROGR+ button each have a
aiming the Commander at your component, the programmed tactile dot for ease of use.
operations may be performed before you go on with the
procedure.
Operating a TV
2 To change the programme. qf PROGR+:
Troubleshooting
Also to turn on the power. Programme up.
3 To select double-digit PROGR–:
If you have problems setting up or using the Commander:
numbers. Programme down.
•When setting up the Commander, carefully go through the
Works in the same way as qg To turn on.
procedures described in "Setting the Code." If the code that is
your TV's commander. To return from Teletext to
listed first for your component does not work, try other codes
4 To change the input mode. TV.
for that component in the order in which they are listed. If all
6 To switch to Teletext. qh To operate JUMP,
the codes fail to work (or if your component is not listed in this
8 To move the cursor FLASHBACK, or
manual), try using the procedures in "Searching for the Correct
upward, downward, to the CHANNEL on the TV,
Code."
•Check that you are aiming the Commander directly at the right or left. depending on the
9 To call up the MENU manufacturer's setting.
component, and that there are no obstructions between the
display. qk To enter the selection.
Commander and the component.
•Make sure the batteries you are using are not worn out, and qd To select a number between ql Fastext buttons.
20 and 29.
that they are inserted correctly.
•Check that the button of the TV, VCR, SAT, or DVD is pressed
to choose your desired component.
•Check that the component has infrared remote capability. For Operating a VCR
example, if your component did not come with a remote
2 To change the programme. 0, ql and w;
commander, it is probably not capable of being controlled by a
3 To select double-digit N: To play.
remote commander.
numbers. x: To stop.
•Should any problem persist, reset the Commander to the
Works in the same way as m: To rewind.
factory setting by pressing the 1, t and 2– buttons
your VCR's commander. M: To fast-forward.
simultaneously.
4 To switch the signals zREC: To record, press N
supplied to the TV. while pressing
Customer Service
6 To expose the on-screen zREC.
If you have any questions or problems
display. X: To pause.
concerning the Remote Commander that
8 To move the cursor qd To select a number between
are not covered in this manual, please call
upward, downward, to the 20 and 29.
the customer remote helpline. The number
left, or to the right. qf PROGR+:
is mentioned in the warranty card.
9 To call up the MENU Programme up.
display. PROGR–:
Helpline available Programme down.
qg To change the input mode.
qk To enter the selection.
Operating a satellite tuner
Specifications
2 To change the programme. qf PROGR+:
3 To select double-digit Programme up.
Operable distance Approx. 7 m (23 ft) (varies depending of the
numbers. PROGR–:
component of each manufacturer)
Work in the same way as Programme down.
Power requirements Two size AA (R6) batteries (not supplied)
your satellite tuner's qh To operate JUMP,
Battery life Approx. 6 months (varies depending on
commander. FLASHBACK or frequency of use)
4 To change the input mode CHANNEL RETURN Dimensions Approx. 55 × 200 × 32 mm (w/h/d)
(H/V). function on the satellite (2 1 / × 7 7 / × 1 5 / in.)
4 8 16
8 To move the cursor tuner, depending on the Mass Approx. 95 g (3.4 oz.) (not including
upward, downward, to the manufacturer's setting. batteries)
right or left. qj To bring up the Master
Design and specifications are subject to change without notice.
9 To call up the MENU Guide.
display. qk To enter the selection.
The validity of the CE marking is restricted to only those countries
qd To select a number between ql Fastext buttons.
where it is legally enforced, mainly in the countries EEA (European
20 and 29.
Economic Area).
Operating a DVD
2 Number buttons: To set qf PROGR+:
items selected from the To proceed to the
screen. next location or
3 To select numbers 10 and song.
above. Programme up.
4 To change the sound. PROGR–:
6 To show the current play To proceed to the
status on the screen. previous location or
8 To move the cursor song.
upward, downward, to the Programme down.
left, or to the right. qg To switch the subtitle.
9 To display the DVD menu. qh To display the title menu.
0 To record, press N while qj To clear the selected
pressing zREC. characters from the screen.
First release N, then To select the deck.
release zREC. qk To execute items selected
qd To enter the setting. To set from the screen.
items selected from the ql N: To play.
screen. m: To rewind.
M: To fast-forward.
x: To stop.
w; X: To pause.
Component code numbers / Codes des appareils
TV/VCR/COMBO
English
Brand Component Code No.
TV/VCR/COMBO*
The left row of the table shows the brand, the center row Sony TV 001 002 003 004 005 006 007
VCR (VTR1:Betamax) 001 007 010 011
shows the component (TV, VCR or COMBO) and the right
VCR (VTR2:8mm) 002 008
row shows the code No.
VCR (VTR3:VHS) 003 009
* COMBO stands for the unit combined with TV and VCR.
VCR (VTR4:DV) 004
SAT (Satellite tuner)
VCR (VTR5:DV) 005
The left row of the table shows the brand and the right row
VCR (VTR6:DV) 006
shows the code No. Aiwa TV 051
digital: digital satellite tuner VCR 033 065 045
analog: analog satellite tuner Akai TV 061 011 020 056 062
VCR 041 034 043
DVD
Alba TV 081 062
The left row of the table shows the brand and the right row
VCR 039
shows the code No.
Amstrad VCR 039
Audio Sonic TV 081
Français
Baird VCR 049 042
B&O TV 083
TV/VCR/COMBO*
(Bang&Olufsen) VCR 064
La colonne gauche du tableau indique la marque, la colonne
Beko TV 025
du milieu indique l'appareil (téléviseur (TV), magnétoscope
Bestar TV 013
(VCR) ou COMBO) et la colonne droite le n° de code.
Blaupunkt TV 026 028
* COMBO désigne un combiné téléviseur-magnétoscope.
VCR 018 030
SAT (récepteur satellite) Blue sky TV 013
La colonne gauche du tableau indique la marque et la colonne Brandt TV 037
Brionvega TV 048 046
droite le n° de code.
Bush TV 121 081 075 062 010 119
digital: récepteur satellite numérique
analog: récepteur satellite analogique VCR 041
CGM TV 029
DVD
VCR 046 013 044 045
La colonne gauche du tableau indique la marque et la colonne
COMBO TV 029&VCR 013
droite le n° de code. Clatronic TV 013 014
VCR 039
Continental TV 076
To set a Component Code (see the instruction manual for Crown TV 024 033 065
details) Daewoo TV 074 011 013 067 123 124
VCR 058 057
Pour enregistrer un code d'appareil (voir le mode d'emploi
COMBO TV 074&VCR 057
pour plus dedétails)
Deccacolour TV 012 084 085
Dual TV 013 047
S Emerson TV 086 125
Fenner TV 068 008
Ferguson TV 038 066 042 041 037
While pressing the S (SET) button, press the
VCR 067 023 024
1 button.
COMBO TV 074&VCR 057
Finlux TV 022
Tout en maintenant la touche S (SET) enfoncée,
First line TV 013 056
appuyez sur la touche 1.
Fisher TV 056
VCR 039
Fraba TV 013
Funai TV 065
TV VCR SAT DVD
VCR 029
GoldStar/LG TV 092 098 101 011 017 018 013 116
VCR 052 046
COMBO TV 054&VCR 052
Goodmans TV 020 011 062 037 013 014 015 075
Code No.
120
VCR 058 012
COMBO TV 074&VCR 058
Grundig TV 091 026 027 009 022 104
VCR 013 021 018
COMBO TV 009&VCR 013
Hansol TV 117
Hitachi TV 089 093 094 052 053 010 011 015
105
VCR 047 035 048
Höher TV 125 086
Hyper TV 025 008
ICE TV 062
Inno-Hit TV 010
Irradio TV 011 062 068
JVC TV 077 062 078 114
VCR 015 030 059 016
Continued on reverse side
Suite au verso