Operation Instruction Copy Button Pressing the button allows you to copy video clips. COPY Esc Button During menu setup, pressing the button closes the current menu or setup dialog box. Play/Stop Button Pressing the button enters the playback mode, and pressing the button again exits the PLAY/STOP playback mode.
4- & 8-Channel Digital Video Recorder Power LED The POWER LED is lit when the unit is On. USB Port A USB port on the front panel is provided to connect external hard disk or flash drives for video clip copying or system upgrades. Position external drives close enough to the DVR so that you can make the cable connections, usually less than 6 feet.
Operation Instruction ID Button If a DVR System ID is set to 0, the infrared remote control will control that DVR without any additional operations. (Refer to the System Information setup screen in this chapter for further information on setting the System ID.) If the system ID is 1 to 16, you must to press the button and then press the number button (1 to 16 (+10 &...
4- & 8-Channel Digital Video Recorder Stop: Pressing the button stops playback and enters the Live Monitoring mode. Backward: When in the pause mode, pressing the button moves to the previous image. Forward: When in the pause mode, pressing the button moves to the next image.
4- & 8-Channel Digital Video Recorder Chapter 4 ─ Operation NOTE: This chapter assumes your DVR has been installed and configured. If it has not, please refer to Chapters 2 and 3. The DVR’s controls are similar to a VCR. As with a VCR, the main functions are recording and playing back video.
Operation Instruction NOTE: The Live Monitoring menu also can be displayed by moving the mouse pointer to the top of the screen. Live Monitoring Menu Display Selecting (Display Menu) in the Live Monitoring menu displays the following Display Menu. Camera: Selecting Camera and choosing the camera number displays the ...
4- & 8-Channel Digital Video Recorder Sequence Selecting (Sequence) in the Live Monitoring menu causes the cameras to display sequentially. When in one of the multiview formats, selecting Sequence will cause the DVR to go through predefined screen layouts (Full Sequence). Or, the bottom, right screen will display live cameras sequentially (Cameo Sequence).
4- & 8-Channel Digital Video Recorder Zoom Mode (Camera Menu) Zoom in the Live You can enlarge an area of the video by selecting Monitoring menu. For a few seconds after selecting (Camera Menu) Zoom from the Camera, a rectangle displays on the screen.
Operation Instruction Camera Buttons: Pressing the individual camera buttons will cause the selected camera to display full screen. Arrow Buttons: Pressing the button plays video backward at high speed. Pressing the button again toggles the playback speed from . Pressing the button plays video forward at high speed.
4- & 8-Channel Digital Video Recorder NOTE: The Search menu also can be displayed by moving the mouse pointer to the top of the screen. Search Menu Display Selecting (Display Menu) in the Search menu displays the following Display Menu. Camera: Selecting Camera and choosing the camera number displays the ...
Operation Instruction Export Selecting (Export) in the Search menu displays the following Export menu. See the following Clip Copy section for details. EZ Copy: Selecting EZ Copy will set the starting point of the video to be clip copied, and the icon displays at the bottom-left corner of the screen.
Page 13
Clip-Copy Video clips can be copied on an external USB hard disk or flash drive. The copied video clips can be viewed on computers running Microsoft Windows 98, ME, 2000, XP, Vista or 7. Refer to the Appendix – USB Hard Disk Drive Preparation for information on preparing the external drive for clip copy.
Page 14
You do not need to install any special software on your personal computer to review the video clips. Refer to the Speco Central Operation Instruction for instructions on how to review video clips you have copied. NOTE: During Clip Copy, you cannot shut the system down, clear data on the storage device, or format the storage device.
Page 15
Internet Explorer: Version 6.0 or later Start Internet Explorer on your local PC. You can run the Speco Remote program by entering the following information in the address field. “http://IP address:12088” (The DVR IP address and the Speco Remote port number –...
① Click the to access to the web search mode. ② Position the mouse pointer on the WebWatch logo to see the version of the Speco Remote ③ program. The DVR information window displays the login information of Speco Remote.
NOTE: The icon will display on each camera screen when audio communication is available between the Speco Remote system and a DVR. Web Search Mode Remote Search is a remote web search program that allows you to search recorded video on the remote DVR.
Page 18
Click the to access to the web monitoring mode. ② Position the mouse pointer on the WebSearch logo to see the version of the Speco Remote ③ program. The DVR information window displays the time information of recorded data on the remote ④...
Operation Instruction Click the to save any video clip of recorded data as an executable file, or click the to save ⑪ the current image in a bitmap or JPEG file format. Click the to print the current image on a printer connected to your computer.