Roland HT-TX Owner's Manual

Checking the Included Items Main Features
• The unit This unit is a transmitter/receiver for long-distance transmission of HDMI signals over up to 100 meters using a single LAN cable (Cat5e or higher).
• AC adaptor, insertion plugs (3 types)
• Support for 1080/59.94p (full HD) and 3D video
• RS-232 conversion cable (2 m)
• Support for HDMI 1.4 and HDCP 2.0
• Ferrite core x 3
• Support for RS-232 signals
• Owner's Manual (this document)
Panel Descriptions
HT-TX01 (Transmitter)
* These connectors are not used.
1 2 3
4 5 6
No. Name Explanation
1 Power indicator
This lights up when power is supplied.
2
LINK indicator This lights up when the transmitter/receiver is correctly connected
3 HDMI INPUT connector The HDMI signal from the source device is input here.
4 AC adaptor connector This is for connecting the included AC adaptor.
Attaching the Ferrite Cores
1. Open an included ferrite core by spreading apart the tabs at two places.
2. Attach the ferrite core to an HDMI cable, LAN cable, or RS-232 conversion cable.
* Close the ferrite core by pressing down on each tab until it clicks into place.
Attach near the base of the plug at
the end that connects to the unit.
Attaching an AC Adaptor Insertion Plug
1. Attach an included AC adaptor insertion plug to the AC adaptor.
* Attach the insertion plug for your country or region.
* Attach the insertion plug by pressing it in until it clicks into place.
* Be sure always to use the included AC adaptor with the unit.
To detach, pull out the insertion plug
while squeezing the left and right
sides of the lock section inward.
Owner's Manual
HT-RX01 (Receiver)
* These connectors are not used.
1 2 7
4 8 6
No. Name Explanation
5 HDBaseT (TX) connector
This is for connecting a receiver.
This is for connecting a remote-control device (RS-232-compatible
6
RS-232 connector
computer, projector, or the like) using the included RS-232 conversion cable.
7 HDMI OUTPUT connector This outputs the HDMI signal to a display device.
This is for connecting a transmitter, Roland XS series unit, or other such
8
HDBaseT (RX) connector
device.
Connection Examples
* For a connection to the HDBaseT connector, use a Cat5e (Category 5e) or higher shielded LAN cable.
* *For a connection to the RS-232 connector, use the included RS-232 conversion cable.
Roland XS series device, etc. Roland V-40HD device, etc.
RS-232 HDBaseT OUTPUT
connector
connector
HDMI OUTPUT
connector connector
RS-232
connector
HT-TX01
RS-232-compatible
device (computer, etc.)
HT-RX01
HT-RX01
HDMI INPUT
HDMI INPUT
connector
connector
RS-232
connector
Displays, RS-232-compatible
Displays, RS-232-compatible
projectors, etc. projector, etc. device (computer, etc.)
projectors, etc.
Before using this unit, carefully read the sections entitled "USING THE UNIT SAFELY" and "IMPORTANT NOTES"
on back side. These sections provide important information concerning the proper operation of the unit.
Additionally, in order to feel assured that you have gained a good grasp of every feature of your new unit, read
Owner's Manual in its entirety. This manual should be saved and kept on hand as a convenient reference.
RS-232 Connector (RS-232 Conversion Cable) Specifications
Pin No.
1 2 3 4 5
1
2
1 2 3 4 5 3
4
5
6 7 8 9
6
D-sub 9-pin (male)
7
RXD
8
6 7 8 9 TXD GND
9
RXD
TXD GND
Communication method Synchronous (asynchronous), full-duplex
Communication speed
Parity
Data length
3.5mm miniature
Stop bit
phone plug
Code set
Flow control
Main Specifications
Input Formats 480/59.94i, 576/50i, 480/59.94p, 576/50p, 720/59.94p, 720/50p,
1080/59.94i, 1080/50i, 1080/59.94p, 1080/50p, 640 x 480, 800 x 600,
1024 x 768, 1280 x 768, 1280 x 1024, 1366 x 768, 1400 x 1050,
1600 x 1200, 1920 x 1200
* RGB formats : Conforms to VESA DMT Version 1.0 Revision 11.
* The maximum refresh rates of RGB is 75 Hz. (excluding 1600 x 1200
and 1920 x 1200. The refresh rate of these 2 is 60Hz)
* 1920 x 1200/60Hz : Reduced blanking
* Also check the supported resolutions of the connected device.
Audio Formats The maximum is PCM 8ch, Dolby Digital, True HD DTS-HD Master Audio
Input Connectors HT-TX01 HDMI x 1: Type A 19 pins
HT-RX01 RJ45 x 1
Output Connectors
HT-TX01 RJ45 x 1
HT-RX01 HDMI x 1: Type A 19 pins
Other Connectors RS-232 x 1: 9 pins D-sub type * When using additional RS-232 cable.
Transmission distance The maximum is 100 m (328 ft)
* The available distance depends on the quality of the LAN cable.
Operating temperature range 0 to 40 degree C
32 to 104 degrees F
Operating temperature humidity 10 to 85 % (no condensation)
Storage temperature range -20 to 60 degree C
-4 to 140 degrees F
RS-232
Storage temperature humidity 10 to 85 % (no condensation)
Power Supply AC Adaptor
Current Draw 2 A
Dimensions 81 (W) x 93 (D) x 24 (H) mm
3-3/16 (W) x 3-11/16 (D) x 1 (H) inches
Weight excl. AC adaptor
300 g
11 oz
* In the interest of product improvement, the specifications and/or appearance of this unit are subject to
change without prior notice.
For EU Countries
RS-232
connector
Cable Wiring Diagram
Signal
When using the included RS-232 conversion cable, RXD, TXD, and GND are wired as shown below.
N.C.
RXD Unit end
(conversion cable end)
TXD
N.C. : 1
N.C.
RXD : 2
GND
TXD : 3
N.C.
N.C. : 4
N.C.
GND : 5
N.C.
N.C. : 6
N.C.
N.C. : 7
N.C. : 8
N.C. : 9
9600 bps, 19200 bps, 38400 bps, 115200 bps
none
* When you want to extend the RS-232 conversion cable, use a straight cable.
8 bit
1 bit
ASCII
none
Dimensions
Copyright © 2014 ROLAND CORPORATION
All rights reserved. No part of this publication may be reproduced in
any form without the written permission of ROLAND CORPORATION.
Controller end
1 :
2 : RXD
3 : TXD
4 :
5 : GND
6 :
7 :
8 :
9 :
73.4
81
69
For China
* 5 1 0 0 0 4 4 5 9 1 - 0 1 *