Advertisement
Quick Links
Advertisement
Related Manuals for Honeywell 9007AX01
Summary of Contents for Honeywell 9007AX01
- Page 1 Universal Vehicle Power Supply 9007AX01 Installation Instructions...
- Page 2 Disclaimer Honeywell International Inc. (“HII”) reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult HII to determine whether any such changes have been made. The information in this publication does not represent a commitment on the part of HII.
-
Page 3: What You Get
About the Universal Vehicle Power Supply The universal vehicle power supply kit provides filtered and regulated 12 VDC output power, as well as short circuit, over- voltage, and over-temperature protection. The vehicle voltage input range for this supply is 6 to 96 VDC. Universal Vehicle Power Supply Requirements Computer Computer Electrical Rating... - Page 4 About the Vehicle Voltage Make sure that your vehicle’s electrical system is in good working condition for all types of installations. The charging circuit must work properly and vehicle generated electrical “noise” must be minimized. Excess electrical noise can be severe enough to defeat the electrical filtering that is built into Intermec products.
- Page 5 Install the Y-Cable 1 Connect the 3-pin connector and the 2 -pin connector of the y-cable to the power supply. 2 Connect one of these adapter cables to the y-cable and the computer: • P/N VE027-8024-C0 (CV31 or CV61) • P/N 236-294-001 (CV41) This illustration shows connecting adapter cable P/N VE027-8024-C0 to the y-cable and a CV61.
- Page 6 Install the CV31 Ignition Sensing Cable (Optional) Install the CV31 ignition sensing cable to automatically turn on the CV31 when the operator turns on the vehicle. 1 Connect the ignition (blue) wire to the ignition circuitry of the vehicle (up to 60 V). 2 Connect the grounding (black) wire to the vehicle chassis for electrostatic discharge (ESD) protection.
- Page 7 About the Vehicle Battery Cable Follow these installation guidelines: • The power supply can draw up to 0.25 A, even with no load. So, for gas-powered vehicles, you also need to install an On/Off switch with a minimum of 15 A DC rating or an automatic shut-off device in series with the inline fuse holder.
- Page 8 4 Install heat shrink tubing on the battery cable jacket. Battery cable jacket Black wire Red wire Ground wire Heat shrink tubing Heat shrink tubing Fuse Green wire White wire Terminal ring 5 Insert and secure the fuse in the fuse holder assembly. 6 Assemble the negative wire: Strip 0.60 cm (0.25 in) of insulation from the green and white wires.
- Page 9 9 Crimp a 3/8-inch terminal ring onto the braided ground wire. 10 Connect the 4-pin connector to the power supply. 11 Connect the battery cable to the vehicle battery. For more information, see the next section. How to Connect to the Vehicle Battery The procedure you use to connect to the vehicle battery depends on the location of the battery terminal: •...
- Page 10 3 Slide the positive fuse link terminal ring from the input power cable onto positive battery clamp bolt. 4 Place another 3/8-inch washer onto the battery clamp. 5 Thread another 3/8-inch nut onto the battery clamp bolt and tighten the nut securely. 6 Repeat Steps 1 through 5 for the negative wire.
-
Page 11: Power Connector Pin Assignments
5 Put another 3/8-inch washer on the battery terminal post. 6 Slide the positive battery cable on the post. 7 Insert the post assembly (Steps 2 through 6) into the positive battery terminal. 8 Tighten the battery terminal post securely. 9 Tighten the nut installed in Step 2 to secure the washers and cables firmly in place. - Page 12 Vin+ heater 12 V regulated DC+ for heated display Vin+ 12 to 60 V non-regulated DC+ input Honeywell Scanning & Mobility 9680 Old Bailes Road Fort Mill, SC 29707 www.honeywellaidc.com Universal Vehicle Power Supply (9007AX01) Installation Instructions *931-088-003* P/N 931-088-003...