Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Kenwood KDC-MP5029V
Summary of Contents for Kenwood KDC-MP5029V
- Page 1 CD-RECEIVER KDC-MP5029V KDC-MP5029VG INSTRUCTION MANUAL © B64-3051-00/00 (MW)
-
Page 2: Table Of Contents
Contents Safety precautions Notes About CDs About,MP3, and WMA General features Power Selecting the Source Volume Attenuator System Q Audio Control Audio Setup Speaker Setting Theft Deterrent Faceplate Switching Display Dimmer Control TEL Mute Tuner features Tuning Tuning Mode Station Preset Memory Auto Memory Entry Preset Tuning Frequency Step Setting... -
Page 3: Safety Precautions
KENWOOD disc changers/ CD players released in 1998 or later can be connected to this unit. Refer to the catalog or consult your Kenwood dealer for connectable models of disc changers/ CD players. Note that any KENWOOD disc changers/ CD players released in 1997 or earlier and disc changers made by other makers cannot be connected to this unit. -
Page 4: Notes
Notes • If you experience problems during installation, consult your Kenwood dealer. • If the unit fails to operate properly, press the Reset button. The unit returns to factory settings when the Reset button is pressed. • Press the reset button if the disc auto changer fails to operate correctly. -
Page 5: About Cds
About CDs Handling CDs • Don’t touch the recording surface of the CD. • CD-R and CD-RW are easier to damage than a normal music CD. Use a CD-R or a CD-RW after reading the caution items on the package etc. •... -
Page 6: About,Mp3, And Wma
About, MP3 and WMA The playable MP3/WMA file (hereafter called Audio file) and the media format has the following limitation. The Audio file, which is out of the specification, may not able to be played normally, or the file and folder names may not be displayed correctly. -
Page 7: General Features
General features ATT/DIM Release button ATT indicator Power Turning ON the Power Press the [SRC] button. • When the power is ON, the <Security Code> (page 18) is displayed as "CODE ON" or "CODE OFF". Turning OFF the Power Press the [SRC] button for at least 1 second. Selecting the Source Press the [SRC] button. -
Page 8: Attenuator
General features Attenuator Turning the volume down quickly. Press the [ATT] button. Each time the button is pressed, the Attenuator turns ON and OFF. When it’s ON, the "ATT" indicator blinks. System Q You can recall the best sound setting preset for different types of music. -
Page 9: Speaker Setting
Speaker Setting Fine-tuning so that the System Q value is optimal when setting the speaker type. Enter Standby Press the [SRC] button. Select the "STANDBY" display. Enter Speaker Setting mode Press the [VOL] knob. Select the Speaker type Turn the [VOL] knob. Each time the knob is turned, the setting switches as shown below. -
Page 10: Switching Display
General features Switching Display Switching the information displayed. Enter Switching Display mode Press the Control knob for at least 1 second. "DISP SEL" is displayed. Select the Display item Push the Control knob to [4] or [¢]. In Tuner source Information Frequency Clock... -
Page 11: Tuner Features
Tuner features Tuning Selecting the station. Select tuner source Press the [SRC] button. Select the "TUNER" display. Select the band Push the Control knob to [FM] or [AM]. Each time the knob is pushed to [FM], it switches between the FM1, FM2, and FM3 bands. Tune up or down band Push the Control knob to [4] or [¢]. -
Page 12: Auto Memory Entry
Tuner features Auto Memory Entry Putting stations with good reception in the memory automatically. Select the band for Auto Memory Entry Push the Control knob to [FM] or [AM]. Open Auto Memory Entry Press the [AME] button for at least 2 seconds. When 6 stations that can be received are put in the memory Auto Memory Entry closes. -
Page 13: Cd/Audio File/Vcd/External Disc Control Features
CD/Audio file/VCD/External disc control features Release button Playing CD, Audio file & VCD When there is no disc inserted Drop open the faceplate Press the Release button. Insert a disc. Push the faceplate on the left side, and return it to its former position. •... -
Page 14: Playing External Disc
CD/Audio file/VCD/External disc control features Playing External Disc Playing discs set in the optional accessory disc player connected to this unit. Press the [SRC] button. Select the display for the disc player you want. Display examples: Display Disc player "CD CH" CD changer "MD CH"... -
Page 15: Scan Play
In CD ,VCD & External disc source Repeat play Display Track Repeat "TRACK REP" Disc Repeat (In Disc Changer) "DISC REP" "REP OFF" In Audio file Repeat play Display File Repeat "FILE REP" Folder Repeat "FOLD REP" "REP OFF" Scan Play Playing the first part of each song on the disc you are listening to and searching for the song you want to listen to. -
Page 16: Folder Select
CD/Audio file/VCD/External disc control features Function of Audio file Folder Select Quickly selecting the folder you want to listen to. Enter Folder Select mode Press the [F.SEL] button. "F-SELECT" is displayed. During Select mode the folder information is displayed as shown below. Folder name display Displays the current folder name. -
Page 17: Menu System
Menu system Menu System Setting during operation beep sound etc. functions. The Menu system basic operation method is explained here. The reference for the Menu items and their setting content is after this operation explanation. Enter Menu mode Press the [MENU] button for at least 1 second. "MENU"... -
Page 18: Security Code
Menu system In Standby mode Security Code Because authorization by the Security Code is required when it’s removed from the vehicle, personalizing this unit is by using the Security Code is a help in preventing theft. • When the Security Code function is activated, it can’t be released. -
Page 19: Dsi (Disabled System Indicator)
Exit Clock adjustment mode Press the [MENU] button. In Standby mode DSI (Disabled System Indicator) A red indicator will blink on the unit after the faceplate is removed, warning potential thieves. Display Setting "DSI ON" LED flashes. "DSI OFF" LED OFF. In FM reception CRSC (Clean Reception System Circuit) -
Page 20: Cd Read Setting
Menu system In Standby mode CD Read Setting When there is a problem on playing a CD with special format, this setting play the CD by force. Display Setting "CD READ 1" Play CD and Audio file. "CD READ 2" Play CD by force. -
Page 21: Basic Operations Of Remote
Basic Operations of remote FM/AM/ Not Used [0] — [9] Loading and Replacing the battery Use two "AA"-size batteries. Slide the cover while pressing downwards to remove it as illustrated. Insert the batteries with the + and – poles aligned properly, following the illustration inside the case. -
Page 22: In Disc Source
Basic Operations of remote Audio Control [AUD] button Select the Audio item for adjustment. [VOL] buttons Adjust the Audio item. • Refer to <Audio Control> (page 8) for the operation method, such as the procedures of Audio control and others. In Tuner source [FM]/ [AM] buttons Select the band. -
Page 23: Accessories/Installation Procedure
Accessories/ Installation Procedure Accessories Installation Procedure 1. To prevent a short circuit, remove the key from the ignition and disconnect the - battery. 2. Make the proper input and output wire ...1 connections for each unit. 3. Connect the speaker wires of the wiring harness. 4. -
Page 24: Connecting Wires To Terminals
To rear right speaker Car fuse box (Main fuse) English To connect these leads, refer to the relevant instruction manuals. To KENWOOD disc changer/ External optional accessory Fuse (10A) Power control wire (Blue/White) P.CONT Motor antenna control wire (Blue) ANT. -
Page 25: Installation
Installation non-Japanese cars Metal mounting strap (commercially available) Firewall or metal support Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. Self-tapping screw (commercially available) Screw (M4X8) (commercially available) • Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (for example, the sound may skip). - Page 26 Installation Screwing the Faceplate on the Unit If you want to fasten the faceplate to the main unit so that it does not fall off. Refer to the section <Removing the hard rubber frame> (page 27) and then remove the hard rubber frame.
-
Page 27: Removing The Unit
Removing the Unit Removing the hard rubber frame Engage the catch pins on the removal tool and remove the two locks on the upper level. Upper the frame and pull it forward as shown in the figure. Accessory2 Removal tool When the upper level is removed, remove the lower two locations. -
Page 28: Troubleshooting Guide
Troubleshooting Guide What might seem to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Before calling service, first check the following table for possible problems. General The power does not turn ON. ✔... - Page 29 Tuner source Radio reception is poor. ✔ The car antenna is not extended. ☞ Pull the antenna out all the way. ✔ The antenna control wire is not connected. ☞ Connect the wire correctly, referring to the section on <Connecting Wires to Terminals>. Disc source "AUX EXT"...
- Page 30 LOAD: Discs are being exchanged in the Disc changer. IN (Blink): The CD player section is not operating properly. ➪ Reinsert the CD. If the CD cannot be ejected or the display continues to flash even when the CD has been properly reinserted, please switch off the power and consult your nearest service center.
-
Page 31: Specifications
Treble : 10 kHz ±10 dB Preout level / Load (during disc play) : 2000 mV/10 kΩ Preout impedance : ≤ 600 Ω CD player section Laser diode : GaAlAs Digital filter (D/A) : 8 Times Over Sampling D/A Converter...