Kenwood KDC-MP338 Instruction Manual
Kenwood cd-receiver instruction manual
Hide thumbs
Also See for KDC-MP338:
- Training manual (52 pages) ,
- Instruction manual (68 pages) ,
- Instruction manual (68 pages)
Table of Contents
Advertisement
KDC-X492
KDC-MP438U
KDC-MP408U
KDC-MP338
CD-RECEIVER
INSTRUCTION MANUAL
AMPLI-TUNER LECTEUR DE CD
MODE D'EMPLOI
REPRODUCTOR DE DISCOS COMPACTOS RECEPTOR DE FM/AM
MANUAL DE INSTRUCCIONES
Kenwood Corporation
~
'~IO'"
READY
H3'Radio·
'!IREADY
«i
Me
D
Madefor
@J
iPod
Take the time to read through this instruction manual.
Familiarity with installation and operation procedures will help you obtain the best
performance from your new CD-receiver.
For your records
Record the serial number, found on the back of the unit, in the spaces designated on the
warranty card, and in the space provided below. Refer to the model and serial numbers
whenever you call upon your Kenwood dealer for information or service on the product.
Model KDC-X492/MP438U/MP408U1MP338 Serial number
_
US Residence Only
©
864-3955-00/00
(KW)
Advertisement
Table of Contents
Related Manuals for Kenwood KDC-MP338
Summary of Contents for Kenwood KDC-MP338
- Page 1 Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the space provided below. Refer to the model and serial numbers whenever you call upon your Kenwood dealer for information or service on the product. Model KDC-X492/MP438U/MP408U1MP338 Serial number US Residence Only ©...
-
Page 2: Table Of Contents
Deactivating Security Code Manual Clock Adjustment AMP Control Auxiliary Input Display Setting Receive mode Setting Demonstration mode Setting Basic Operations of remote control 15 KDC-X492/KDC-MP438U/KDC-MP408U/KDC-MP338 Accessories/Installation Procedure 18 Connecting Wires to Terminals Installation Troubleshooting Guide Specifications Panel illustrations used in this... -
Page 3: Before Use
CDs to play. In such a situation, remove the disc and wait for the condensation to evaporate. If the unit still does not operate normally after a while, consult your Kenwood dealer. • If you experience problems during installation, consult your Kenwood dealer. -
Page 6: General Operation
On the KDC-X492/KDC-MP438U/KDC- MP408U, this item can be selected at any time. On the KDC-MP338, this item is displayed only when the tone quality has been adjusted. On the KDC-MP338, this item disappears when another setting is selected. -
Page 7: Audio Setup
Audio Setup - - - - You can set Sound system, such as follows; Front High Pass Filter* "HPF" Through/40*'/60*'/80/100/120/ 1501180/220*' Hz Rear High Pass Filter* "HPR" Through/40*1/60*1/80/100/120/ 1501180/220*' Hz Low Pass Filter "LPF SW" 50*'/60*1.2/801100*1/1201160*3/ Through Hz Subwoofer Phase* "PHASE"... -
Page 8: Display Switching
In Standby! input I n _ 1 ' .._ _ Source name Clock KDC-X492/KDC-MP438U1KDC-MP408U/KDC-MP338 Enter Switching Display mode [~II] Press the "DISPLAY SEL" is displayed. Select the Display item Push the Control knob towards right or left. -
Page 9: Tuner Operation
Tuner Operation Function of remote control Direct Access Tuning Entering the frequency and tuning. Enter Direct Access Tuning mode Press the [DIRECT] button on the remote control. "- - - -" is displayed. Enter the frequency Press the number buttons on the remote control. -
Page 10: Music Disc/Audio File Operation
Press the button. • Direct Music Search cannot be performed during playing of iPod, Random play, or scan play. KDC-X492/KDC-MP438U/KDC-MP408U/KDC-MP338 Function of disc changers with remote control Direct Disc Search Searchs the disc by entering the disc number. Enter the disc number Press the number buttons on the remote control. -
Page 11: Ipod Select
Cancelling the Multi Jog Select mode Press the [MJOG] button. • Track Select is available only during playing of the built- in CD player. • Track Select cannot be performed during Random play or scan play. I 11... -
Page 12: Menu Operation
*Factory setting *1 Function of KDC-X492. *2 Function of KDC-MP438U. *3 Function of KDC-MP408U. *4 Function of KDC-MP338. Displayed item is depending on currently selected source, The mark in Source column shows the KDC-X492/KDC-MP438U/KDC-MP408U/KDC-MP338 source to which the item is displayed. -
Page 13: Deactivating Security Code
Repeat steps 3 and 4, and complete the Security Code. Confirm the Security Code Press the Control knob for at least When "RE-ENTER" is displayed, "CODE" is also displayed. Do the step through operation, and reenter the Security Code. "APPROVED" is displayed. The Security Code function activates. -
Page 14: Auxiliary Input Display Setting
For how to select menu items, refer to <Menu System>(page 12). Enter Receive mode Press the Control knob for at least 1 second. KDC-X492/KDC-MP438U/KDC-MP408U/KDC-MP338 Set the Receive mode Push the Control knob towards up or down. Exit Receive mode Press the [MJOG] button. -
Page 15: Basic Operations Of Remote Control
Basic Operations of remote control VOL-~~ __-+++--An AUD--+__ *!--DIRECT *KDC-X4921MP438U/MP408U General control Volume control [VOL] ~[SRCJ Source select Volume reduce [ATT] When the button is pressed again, the volume returns to the previous level. When the volume is reduced, the "AD" indicator flashes. In Audio control Audio item select [AUD]... - Page 16 • When the iPod is connected to this unit, "KENWOOD" or ",/" is displayed on the iPod to indicate that you cannot operate the iPod. • When the USB device is connected to this unit, it can be charged up provided that this unit is powered.
- Page 17 Disconnection Massage>, and <Rejecting an Incoming call>, press [AUTO] button for at least 1 second. Moreover, some displays are different from the description of KCA-BT1 00 Instruction Manual. "DISCONCT" "HF DISCONCT" "CONNECT" "HF CONNECT" "PHN-DEl." "DEVICE DEl" "P-STATUS" "DVC STATUS" "BT-CON Y"...
-
Page 18: Accessories/Installation Procedure
Kenwood disc changers/ CD players released in 1998 or later can be connected to this unit. Refer to the catalog or consult your Kenwood dealer for connectable models of disc changers/ CD players. Note that any Kenwood disc changers/ CD players released in 1997 or earlier and disc changers made by other makers cannot be connected to this unit. -
Page 19: Connecting Wires To Terminals
: in the vehicle. IConnect to the terminal that is grounded when either the :§ To connect the Kenwood navigation system, consult your navigation manual. ~;;:;:--l--4- : Depending on what antenna you are using, connect either to :the control terminal of the motor antenna, or to the power Herminal for the booster amplifier of the film-type antenna. -
Page 20: Installation
0Smm 05mm Accessory@...for Nissan car Accessory@...forToyota car KDC-X492/KDC-MP438U/KDC-MP408U/KDC-MP338 Removing the hard rubber frame Engage the catch pins on the removal tool and remove the two locks on the upper level. Upper the frame and pull it forward as shown in the figure. -
Page 21: Troubleshooting Guide
Troubleshooting Guide Some functions of this unit may be disabled by some settings made on this unit. o · Cannot set up the subwoofer. • Cannot set up the High Pass Filter. • Cannot set up the Fader. • No Audio control effect on AUX. •... - Page 22 If the "E-99" code does not disappear, consult your nearest service center. IN (Blink): The CD player section is not operating properly. Reinsert the CD. If the CD cannot be ¢ ejected or the display continues to flash...
-
Page 23: Specifications
: 40 dB AM tuner section Frequency range (10kHz space) : S30 kHz - 1700 kHz Usable sensitivity (SIN = 20dB) : 28 CD player section Laser diode : GaAIAs Digital filter (D/A) : 8 Times Over Sampling A Converter... - Page 25 Kenwood Corporation 2967-3, ISHIKAWA-MACHI, HACHIOJI-SHI TOKYO, JAPAN KENWOOD CORP CERTIFIES THIS EQUIPMENT CONFORMS TO DHHS REGULATIONS N0.21 CFR 1040. 10, CHAPTER 1, SUBCHAPTER Location: Bottom Panel...
- Page 27 Questa scheda necessaria per acquistare un nuovo pannello frontale dopo un furto danni. Atencion: Esta tarjeta es necesaria para comprar el panel en el caso de que Ie haya sido robado se haya estropeado. KENWOOD Car Audio Passport Kenwood Corporation...
- Page 28 Name of set Nom de I'appareil Modello dell'apparecchio ~\m~1~\\il\\1 III I1\\1\11 019048 176325 NO.1 Serial No. de serie Serien-Nr. User name Nom de I'utilisateur Eigentumer-Name Nome del proprietario Usuario User address Adresse de I'utilisateur Adresse Indirizzo Direcci6n Phone Phono Telefon ITelefono Telefono Modell Sales dete...
- Page 29 ATTENTION Before using this product for the first time Demonstration function is set to ON as the original setting for this product. It is recommended that this feature is turned OFF at the time of installation, or before initial use of the product. If the Demonstration mode is left in the ON position, the display will change arbitrarily and the security code feature can not be accessed.
- Page 30 Dear Customer, Thank you for purchasing this kenwood product. As mentioned in the pages of this booklet, our warranty is only valid in the countries listed. If your country is not listed please contact your retailer for information on warranty procedure, or write to:...
- Page 31 The following are not covered by the warranty: Any product which is not distributed in the U.S.A. by Kenwood orwhich is not purchased in the U.S.A. from an authorized Kenwood car stereo dealer or an automobile dealer, unless the product is purchased through the U.S.A Military Exchange Service.
- Page 32 Kenwood sont garanties pendant la periode d'un III an a compter de la date d'achat, de bail ou de location originale. sauf dans les cas ou les produits Kenwood sont employes dans un but professionnel ou commercial.