Kenwood KDC-BT8041U Instruction Manual page 34

Appendix
Menu Glossary
• SRC Select
Setting up the Source Select mode.
1 : Displays source icons for your choice.
2 : Allows you to select sources one after another.
• BT DVC Status (Displaying the Bluetooth device
Status)
You can display the connection status, signal
strength, and battery level.
: Bluetooth cell-phone connection status.
: Bluetooth Audio connection status.
: Battery level of cell-phone.
Full
: Signal strength of cell-phone.
Maximum
⁄
• Icons are not displayed if information cannot be
obtained from the cell-phone.
• Since the number of steps of the control unit is different
from that of the cell-phone, the statuses displayed on
the control unit may discord from those displayed on
the cell-phone.
• Auto Answer (Setting the Time Interval for
Automatic Answer)
This function automatically answers (responds
to) a call after lapse of the preset time interval for
automatic answer.
"OFF" : Does not answer the phone call
automatically.
"0" : Automatically answers the phone call at once.
"1s" – "99s" : Automatically answers the phone call
after lapse of 1 – 99 seconds.
⁄
• If the time set in the cell-phone is shorter than that set in
the unit, the former will be used.
• This function does not work for call waiting.
• SP Select (Setting up the Voice Output
Speakers)
You can specify the voice output speakers.
"Front" : Outputs voice from the front-left and front-
right speakers.
"F-R" : Outputs voice from the front-right speaker.
"F-L" : Outputs voice from the front-left speaker.
⁄
• Select the speaker which is further from the microphone
in order to prevent howling or echoes.
• Call Beep (Setting the Beep of the Incoming
Call)
You can output a beep from the speaker when a
call comes in.
"ON" : Beep is heard.
"OFF" : Beep is canceled.
34
| KDC-BT8041U/ KDC-BT8141U
Nearly dead
Minimum
• Display
If this unit is not operated at least 5 seconds with
"OFF" selected, the display turns off. During a setup
mode, the display will not turn off even if 5 seconds
lapse.
• ILM Dimmer (illumination dimmer)
Reduces the key Illumination brightness.
AUTO: Dims the illumination in conjunction with
the Light switch of the vehicle.
MNAL1: Dims the illumination constantly.
MNAL2: Turns off the upper and lower illuminations,
and dims the left and right illuminations.
OFF: Does not dim the illumination.
• SWPRE (Switching Preout)
Switches the preout between rear output ("Rear")
and subwoofer output ("Sub-W").
• AMP
Selecting "OFF" turns off the built-in amplifier.
Turning off the built-in amplifier improves the
quality of the sound from Preout.
• Zone2 (Dual Zone)
Set the destination (front speaker "Front" or rear
speaker "Rear") of the sub source (AUX IN) when the
Dual Zone function is turned on.
• Supreme
Technology to extrapolate and supplement with
proprietary algorithm, the high-frequency range
that is cut off when encoding at low bit rate (less
than 128Kbps, Sampling frequency is 44.1kHz).
Supplementing is optimized by compression
format (AAC, MP3 or WMA) and processed
according to bit rate.
The effect is negligible with music that is encoded
at high bit rate, variable bit rate or has minimal high
frequency range.
• News (News Bulletin with Timeout Setting)
Automatically receives news bulletin when it
starts. Set the time during which interrupt is to be
disabled after start of another news bulletin.
Changing "News 00min" to "News 90min" turns this
function ON.
If news bulletin starts when this function is ON,
"NEWS" is displayed and news is received. If "20min"
is has been set, reception of another news bulletin
will not start for 20 minutes.
The news bulletin volume is the same level that
was set for Traffic Information.
• Seek Mode (Tuning mode select)
Select a tuning mode of the radio.
Tuning mode Display
Auto seek "Auto1"
Preset station seek "Auto2"
Manual "Manual" Normal manual tuning control.
Operation
Automatic search for a station.
Search in order of the stations in the
Preset memory.