Contents Safety precautions Notes General features Power Selecting the Source Volume Attenuator Audio Control Audio Setup Bass Boost Speaker Setting Clock Display Subwoofer Output Theft Deterrent Faceplate TEL Mute Tuner features Tuning Tuning Mode Station Preset Memory Auto Memory Entry Preset Tuning Frequency Step Setting CD player features...
CDs to play. In such a situation, remove the disc and wait for the condensation to evaporate. If the unit still does not operate normally after a while, consult your Kenwood dealer. English...
• If you experience problems during installation, consult your Kenwood dealer. • When you purchase optional accessories, check with your Kenwood dealer to make sure that they work with your model and in your area. • Characters in the LCD may become difficult to read in temperatures below 5 ˚C (41 ˚F).
General features Release button Power Turning ON the Power Press the [SRC] button. Turning OFF the Power Press the [SRC] button for at least 1 second. Selecting the Source Press the [SRC] button. Source required Tuner Standby (Illumination only mode) Clock display Volume Increasing Volume...
General features Audio Control Select the source to adjust Press the [SRC] button. Enter Audio Control mode Press the [VOL] knob. Select the Audio item to adjust Press the [VOL] knob. Each time you press the knob, the item to be adjusted alternates between the items shown in the table below.
Speaker Setting Fine-tuning so that the System Q value is optimal when setting the speaker type. Enter Standby Press the [SRC] button. Select the "STBY" display. Enter Speaker Setting mode Press the [VOL] knob. Select the Speaker type Turn the [VOL] knob. Each time you turn the knob, the setting alternates between the settings shown in the table below.
Tuner features ST indicator Tuning Selecting the station. Select tuner source Press the [SRC] button. Select the "TUnE" display. Select the band Push the Control knob towards [FM] or [AM]. Each time you push the knob toward [FM], it switches between the FM1, FM2, and FM3 bands. Tune up or down band Push the Control knob towards [4] or [¢].
Station Preset Memory Putting a station in the memory. Select the band Push the Control knob towards [FM] or [AM]. Select the frequency to put in the memory Push the Control knob towards [4] or [¢]. Put the frequency in the memory Press the desired [1] —...
CD player features RDM indicator REP indicator IN indicator Playing CD When a disc is inserted Press the [SRC] button. Select the "CD" display. ⁄ • When a CD is inserted, the "IN" indicator is ON. Pause and play Press the Control knob. Each time you press the knob, the audio pauses or plays.
Track Search Selecting the song you want to hear. Push the Control knob towards [4] or [¢]. Track Repeat Replaying the song you are listening to. Press the [REP] button. Each time you press the button, the Track Repeat turns ON or OFF. When the Track Repeat is ON, the "REP"...
Menu system Menu System Setting beep sound during operation, etc. functions. The Menu system basic operation method is explained here. The reference for the Menu items and their setting content is after this operation explanation. Enter Menu mode Press the [MENU] button for at least 1 second. "MEnU"...
In Standby mode Manual Clock Adjustment Select Clock Adjustment mode Push the Control knob towards [FM] or [AM]. Select the "CLCK" display. Enter Clock Adjust mode Press the Control knob for at least 1 second. The clock display blinks. Adjust the hours Push the Control knob towards [FM] or [AM].
Accessories/ Installation Procedure Accessories English Installation Procedure 1. To prevent a short circuit, remove the key from the ignition and disconnect the - battery. 2. Make the proper input and output wire connections for each unit..1 3. Connect the speaker wires of the wiring harness. 4.
Connect to the terminal that is grounded when either the telephone rings or during conversation. ⁄ To connect the Kenwood navigation system, consult your navigation manual. To front left speaker To front right speaker To rear left speaker...
Installation non-Japanese cars Metal mounting strap (commercially available) Firewall or metal support Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. Self-tapping screw (commercially available) Screw (M4X8) (commercially available) ⁄ • Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (for example, the sound may skip).
Removing the hard rubber frame Engage the catch pins on the removal tool and remove the two locks on the upper level. Upper the frame and pull it forward as shown in the figure. Lock Accessory2 Removal tool When the upper level is removed, remove the lower two locations.
Troubleshooting Guide Some functions of this unit may be disabled by some settings made on this unit. Cannot display the user of System Q. <Audio control> (page 6) is not set. • Cannot set up the subwoofer. • No output from the subwoofer. •...