Table of Contents
Advertisement
SECTION
1
WATER SOFTENER
START UP
C, PROGRAM
_SET
WATER HARDNESS
NUMBER
• Press the SELECT 1 button once to display
25
(flashing) and HARDNESS.
The
grains
per
gallon
(gpg)
hardness
of your
water
supply
is on your water
analysis
report.
Be sure
to enter
water
test
re-
sults on page A, for future
refer-
ence.
l___LiGNA ]
HARDNESS
If your
water
supply
contains
iron, compensate
for
it by adding
to the water
hardness
number.
For ex-
ample, assume your water is 20 gpg hard and contains
2
ppm iron. Add 5 to the hardness
number for each 1 ppm
of iron. In this example, you would use 30for your hard-
ness number.
20 gpg hardness
2 ppmironx
5 = 10
+10
(times)
30 HARDNESS
NUMBER
• Press the UP / DOWN
buttons
to set your
water
hardness
number
in the display.
The DOWN
button
moves
the display
to 1. The UP button
moves
the
display
to the highest
setting
(see maximum
setting
for your
model
in the specifications).
Note:
Between
1 and
25, each
press
of the UP / DOWN
button
changes
the display
by 1. Between
25 and
the highest
number,
the
display
changes
5 at a
time...25,
30, 35, etc. Holding
the UP or DOWNbut-
ton in changes
the display
twice
each second.
_[I
SET RECHARGE
(REGENERATION)
TIME
•
Press
the SELECT
1 button
to display
2:00 AM
(flashing)
and RECHARGE
TIME.
At the 2:00 AM
recharge
time
setting,
the softener
begins
re-
generation
(see
pages
2-4 and
....... q,lqN_
....
I-'LIU
RECHARGE
TIME
THE TIMER
2-5) at 2:00 AM, ending
no later than 4:00 AM. This
is a good time in most
households
because
water
is
not being used
(see Automatic
Bypass,
page 2- 6). If
a different
recharge
time setting
would
be better
for
your
household,
do the following.
• Press
the UP / DOWN
buttons
to set the desired
recharge
starting
hour.
Be sure to observe
the AM-
PM as you did when
setting
the present
time of day.
Note:
Each press
of the UP / DOWN
buttons
changes
the
display
one hour.
Holding
the buttons
in changes
the display
twice
each second.
_IE
SET
SALT
TYPE
(sodium
chloride
or potas-
sium
chloride,
see page
1-6):
•
Press
the SELECT
1 button
to display
nACI, the
default
setting.
If you
want
to use
potassium
_'_a
FIF I
chloride
(KC1)
instead
of stan-
-_--_
nnc
i
dard
sodium
chloride
(NaC1)
water
softener
salt, be sure to set
2
KCI in the display
using
the UP
....
button.
The KCI setting
adjusts
V?'_f;
I I-
regeneration
cycle times
to com-
87
C;L I
8
pensate
for the variable
dissolv-
ing rate
of potassium
chloride.
!
Refer
to page
1-6 for informa-
-'-
tion on various
salts.
•
Press
the SELECT
button
once
again,
to com-
plete
initial
programming,
and the current
time of
day will show
in display.
SaLTS_N_
......
!-, -I1-1 _
-_,-
_-I.ZID
7
5
5
2
1
IF YOU NEED
HELP PROGRAMMING
THE TIMER,
CALL TOLL FREE,
NUMBER
1 - 800- 426- 9345.
www.KenmoreWater.com
SEE PAGES 2-1, 2-2 AND
2-3 FOR OTHER
FACE PLATE
TIMER
FEATURES.
1-4
Problems,
Questions?
Call
1- 800- 426- 9345
Kenmore
Water
Line
Hide quick links:
Advertisement
Table of Contents
