Porter-Cable 7519 Instruction Manual
Double insulated routers
Hide thumbs
Also See for 7519:
- Instruction manual (17 pages) ,
- Instruction manual (14 pages) ,
- Instruction manual (3 pages)
Table of Contents
Advertisement
899750 - 02-14-02.qxd
Instruction
manual
To learn more about Porter-Cable
visit our website at:
http://www.porter-cable.com
Copyright © 2002 Porter-Cable Corporation
9/24/02
7:42 AM
Page 1
Double Insulated
Routers
MODEL 7519
Consisting of:
MODEL 75192 Motor
MODEL 75361 Base
Please make certain that the person who is
to use this equipment carefully reads and
understands these instructions before
starting operations.
The Model and Serial No. plate is located on the main
housing of the tool. Record these numbers in the
spaces below and retain for future reference.
Model No. ______________________________________
Type ___________________________________________
Serial No. _______________________________________
ESPAÑOL: PÁGINA 15
FRANÇAISE : PAGE 29
MODEL 7518
Consisting of:
MODEL 75182 Motor
MODEL 75361 Base
IMPORTANT
Part No. 899750 - 02-14-02
Advertisement
Table of Contents
Related Manuals for Porter-Cable 7519
Summary of Contents for Porter-Cable 7519
-
Page 1: Instruction Manual
Consisting of: MODEL 75192 Motor MODEL 75361 Base IMPORTANT Please make certain that the person who is To learn more about Porter-Cable to use this equipment carefully reads and visit our website at: understands these instructions before http://www.porter-cable.com starting operations. -
Page 2: General Safety Rules
899750 - 02-14-02.qxd 9/24/02 7:42 AM Page 2 WARNING: SOME DUST CREATED BY POWER SANDING, SAWING, GRINDING, DRILLING, AND OTHER CONSTRUCTION ACTIVITIES contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: ·... - Page 3 899750 - 02-14-02.qxd 9/24/02 7:42 AM Page 3 Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts. Avoid accidental starting.
- Page 4 If you have questions relative to its application, DO NOT use the tool until you have written Porter-Cable and we have advised you. Technical Service Manager...
-
Page 5: Replacement Parts
When servicing use only identical replacement parts. MOTOR Many Porter-Cable tools will operate on either D.C., or single phase 25 to 60 cycle A.C. current and voltage within plus or minus 5 percent of that shown on the specification plate on the tool. Several models, however, are designed for A.C. -
Page 6: Functional Description
18-20 FUNCTIONAL DESCRIPTION FOREWORD Model 7518 Porter-Cable Router incorporates a speed control that provides operating speeds from 10,000 RPM to 21,000 RPM, to handle the most demanding router applications in various materials. Model 7519 Porter-Cable Router is designed for continuous, rugged operations to handle the most demanding routing applications at 21,000 RPM. - Page 7 899750 - 02-14-02.qxd 9/24/02 7:43 AM Page 7 CAUTlON: While preparing the router for use, while making adjustments, and when router is not in use, ALWAYS DISCONNECT IT FROM THE POWER SOURCE. Fig. 2 ASSEMBLY INSTALLING AND REMOVING THE BIT CAUTION: DISCONNECT TOOL FROM POWER SOURCE.
-
Page 8: Adjusting Depth Of Cut
899750 - 02-14-02.qxd 9/24/02 7:43 AM Page 8 ADJUSTING DEPTH OF CUT CAUTION: DISCONNECT TOOL FROM POWER SOURCE. Fig. 3 Loosen clamp screw (A) Fig. 3. While holding base (E), turn motor unit (F), Fig. 3, COUNTERCLOCKWISE until the tip of the bit is above bottom surface of base. Set router on flat wood surface. -
Page 9: Operation
(2) allow router to cool for three minutes; and, (3) restart router following the instructions in TO START AND STOP ROUTER. SOFT START Model 7518 and 7519 have a “Soft Start” feature designed to minimize startup reaction torque. SPEED CONTROL (Model 7518 only) The speed control is located as shown in Fig. -
Page 10: Using The Router
899750 - 02-14-02.qxd 9/24/02 7:43 AM Page 10 USING THE ROUTER IMPORTANT: Before using your router, consider the kind and total amount of material to be removed. Depending on the material, it may be necessary to make more than one cut to avoid overloading the motor. - Page 11 899750 - 02-14-02.qxd 9/24/02 7:43 AM Page 11 Fig. 6 TEMPLET GUIDES A wide variety of templet guides are available for use in pattern and templet routing operations. Fig. 7 shows a typical combination bit, templet guide, and locknut. CAUTION: DISCONNECT TOOL FROM POWER SOURCE. To install, insert templet guide in center hole in router base and secure in place with the locknut.
-
Page 12: Maintenance
FACTORY SERVICE CENTER. At approximately 100 hours of use, take or send your tool to your nearest authorized Porter-Cable Service Station to be thoroughly cleaned and inspected. Have worn parts replaced and lubricate with fresh lubricant. Have new brushes installed, and test the tool for performance. - Page 13 7:43 AM Page 13 ACCESSORIES A complete line of accessories is available from your Porter-Cable • Delta Supplier, Porter-Cable • Delta Factory Service Centers, and Porter-Cable Authorized Service Stations. Please visit our Web Site for a catalog or for the name of your nearest www.porter-cable.com...
- Page 14 PORTER-CABLE LIMITED ONE YEAR WARRANTY Porter-Cable warrants its Professional Power Tools for a period of one year from the date of original purchase. We will repair or replace at our option, any part or parts of the product and accessories covered under this warranty which, after examination, proves to be defective in workmanship or material during the warranty period.
- Page 15 Pour obtenir des pièces et accessoires pour les produits Porter-Cable • Delta, s’adresser à tout distributeur Porter- Cable • Delta, centre de service agréé ou centre de service d’usine Porter-Cable • Delta. Si vous n’avez accès à aucun de ces centres, appeler le 888-848-5175 et on vous dirigera vers le centre de service d’usine Porter-Cable •...