Related Manuals for JVC LVT1348-003A
Summary of Contents for JVC LVT1348-003A
-
Page 1: Micro Component System
MICRO COMPONENT SYSTEM UX-GD7 —Consists of CA-UXGD7 and SP-UXGD7 INSTRUCTIONS LVT1348-003A... - Page 2 IMPORTANT for the U.K. DO NOT cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or consult your dealer.
-
Page 4: Safety Instructions
“SOME DOS AND DON’TS ON THE SAFE USE OF EQUIPMENT” This equipment has been designed and manufactured to meet international safety standards but, like any electrical equipment, care must be taken if you are to obtain the best results and safety is to be assured. ✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮... -
Page 5: Table Of Contents
Introduction ... 2 Precautions ... 2 How to Read This Manual ... 2 Getting Started ... 3 Step 1: Unpack ... 3 Step 2: Prepare the Remote Control... 3 Step 3: Hook Up... 4 Changing the Scanning Mode ... 6 Selecting the Video Signal ... -
Page 6: Introduction
Precautions Installation • Install in a place which is level, dry and neither too hot nor too cold—between 5°C and 35°C. • Install the System in a location with adequate ventilation to prevent internal heat buildup inside the System. DO NOT install the System in a location near heat sources, or in a place subject to direct sunlight, excessive dust or vibration. -
Page 7: Getting Started
Step 1 :Unpack the package and check the accessories. Step 2 : Prepare the remote control. Step 3 : Hook up the components such as AM/FM antennas, speakers, etc. (see pages 4 to 6). Finally plug the AC power cord. Now you can operate the System. -
Page 8: Step 3: Hook Up
Step : Hook Up If you need more detailed information, see page 6. Illustrations of the input/output terminals below are typical examples. When you connect other components, refer also to their manuals, since the terminal names actually printed on the rear may vary. - Page 9 For better FM/AM reception Vynile-covered wire (not supplied) Extend it horizontally. AM loop antenna Keep it connected. Disconnect the supplied FM antenna, and connect to an outdoor FM antenna using a 75 Ω wire with coaxial type connector (IEC or DIN45325). Set the VIDEO OUT SELECTOR correctly for your TV.
-
Page 10: Changing The Scanning Mode
To assemble and connect the AM loop antenna To assemble the AM loop antenna To connect the AM loop antenna 1 Press and hold 2 Insert • If the AM loop antenna wire or speaker cords are covered with vinyl, remove the vinyl to expose the tip of the antenna by twisting the vinyl. -
Page 11: Before Operating The System
Before Operating the System Playable Disc Types This System has been designed to play back the following discs: Disc Type Mark (Logo) DVD Video DVD Audio Video CD (VCD) DIGITAL VIDEO Super Video CD (SVCD) SUPER VIDEO COMPACT Audio CD DIGITAL AUDIO CD-R Recorded in the Audio CD, VCD, SVCD,... -
Page 12: Display Indicators
Display Indicators The indications on the display teach you a lot of things while you are operating the System. Before operating the System, be familiar with when and how the indicator illuminates on the display. 1 Disc tray indicators • 1–5: Disc tray number indicators •... - Page 13 Indications on the main display while operating a disc While playing back a disc: • DVD Video: Chapter no. Elapsed playing time • By pressing SHIFT+0 (DISPLAY), you can see the current title and chapter numbers for a few seconds. •...
-
Page 14: Daily Operations-Playback
Daily Operations Numeric buttons DISPLAY RETURN MENU/PG GROUP/TITLE 4,¢ FM/PLAY MODE SHIFT 3D PHONIC —Playback Turn on the power. The STANDBY lamp on the main unit turns off. • Without pressing AUDIO by pressing one of the source selecting buttons in the next step. -
Page 15: Listening To The Radio
Listening to the Radio To select the band—FM or AM To tune in to a station While FM or AM is selected... Remote control: Main unit: sec. Frequency starts changing on the display. When a station (frequency) with sufficient signal strength is tuned in, the frequency stops changing. -
Page 16: Playing Back A Disc
Playing Back a Disc • For MP3/JPEG/DivX playback, see “Operations on the CONTROL Screen” on page 31. To insert a disc You can insert a disc while playing another source. Main Unit: To close the disc tray and start playback, press down the same lever again. - Page 17 To locate a particular position While playing a disc except MP3/JPEG... • No sound comes out while searching on DVD Video/ DVD-VR/SVCD/VCD/DivX. To return to normal playback, press DVD/CD 3. Remote To locate an item directly ONLY You can select a title/playlist/chapter/track directly and start playback with the numeric buttons.
- Page 18 For DVD-VR: DVD-VR format has the following two ways of playing. • Original program (ORIGINAL PROGRAM): The System can play back items in a DVD-VR disc in the recorded order conventionally. • Playlist (PLAY LIST): The System can play back the playlist edited with the DVD recording equipment.
-
Page 19: Playing Back From The Pc
Playing Back from the PC This System is equipped with a USB terminal on the front panel. You can connect your PC to this terminal and enjoy the sound out of your PC. When you connect your PC for the first time, follow the procedure below. -
Page 20: Daily Operations
Daily Operations Remote control CANCEL A.STANDBY SLEEP BASS/TREBLE ENTER SHIFT Main unit —Sound&Other Adjustments Adjusting the Volume You can adjust the volume level from level 0 (VOL MIN) to level 31 (VOL MAX). Remote control: DISPLAY DIMMER CLOCK/ TIMER FADE MUTING To drop the volume in a moment AUDIO VOL... -
Page 21: Making Dvd Voice Clear-Clear Voice
Making DVD Voice Clear—CLEAR VOICE Remote ONLY This function allows you to easily understand the dialog of DVD even with the volume turned down. • This function only works for center-channel signal encoded multi-channel disc. Canceled Presetting Automatic DVD Sound Increase Level—DVD LEVEL Remote ONLY... -
Page 22: Changing The Picture Tone-Vfp (Video Fine Processor)
Changing the Picture Tone—VFP (Video Fine Processor) Remote ONLY While showing a playback picture on the TV screen, you can select the preset picture tone, or adjust it and store your own preferences. To select a preset picture tone Activate VFP. NORMAL GAMMA BRIGHTNESS... -
Page 23: Setting The Clock
Setting the Clock Remote ONLY Without setting the built-in clock, you cannot use the Daily Timer (see page 33) and Sleep Timer (see the right column). • To exit from the clock setting, press CLOCK/TIMER as required. • To go back to the previous step, press CANCEL. Activate the clock setting mode. -
Page 24: Advanced Radio Operations
Advanced Radio Operations Remote control SELECT SHIFT Receiving FM Stations with RDS Radio Data System (RDS) allows FM stations to send an additional signal along with their regular program signals. • When tuned to an FM station which provides the RDS service, the RDS indicator lights on the display. -
Page 25: Switching Temporarily To A Program Of Your Choice Automatically
Select a PTY code. (at the same time) NONE O NEWS O AFFAIRS O INFO O SPORT O EDUCATE O DRAMA O CULTURE O SCIENCE O VARIED O POP M O ROCK M O EASY M O LIGHT M O CLASSICS O OTHER M O WEATHER O FINANCE O CHILDREN O SOCIAL O RELIGION O PHONE IN O TRAVEL O LEISURE O JAZZ O COUNTRY O NATION M O... -
Page 26: Unique Disc Operations
Unique Disc Operations Remote control PAGE -/+ DVD/CD 3 ENTER SUBTITLE AUDIO SHIFT Selecting the Sound Track For DVD Video: While playing back a chapter containing audio languages, you can select the language to listen to. For DVD Audio/DivX: While playing back a track containing audio channels, you can select the audio channel to listen to. -
Page 27: Selecting The Subtitle Language
Selecting the Subtitle Language For DVD Video/DivX: While playing back a chapter containing subtitles in different languages, you can select the subtitle language to display on the TV screen. For SVCD: While playing back a track, you can select the subtitle even if no subtitles are recorded on the disc. -
Page 28: Selecting Browsable Still Pictures
Selecting Browsable Still Pictures While playing back a track linked to browsable still pictures (B.S.P.), you can select the still picture (turn the page) to be shown on the TV screen. • This function is only used while playing DVD Audio. •... -
Page 29: Advanced Disc Operations
Advanced Disc Operations Remote control CANCEL Numeric buttons DVD/CD 3 5,∞ 4,¢ FM/PLAY MODE SHIFT Main unit DISC1 Programming the Playing Order— Program Play You can arrange the playing order of the chapters or tracks (up to 99) before you start playback. Before starting playback, activate Program Play. -
Page 30: Playing At Random-Random Play
Start playback. Playback starts in the order you have programmed. To skip a step: To pause: To release, press DVD/CD 3. To check the programmed contents Before or after playback... In the reverse order. In the programmed order. To modify the program Before or after playback... -
Page 31: Playing Repeatedly
Playing Repeatedly Remote ONLY • You can also select the repeat mode using the on-screen bar (see page 29). Repeat Play • For DVD Video/DVD-VR: During playback... Before playback... ALL* Canceled • For DVD Audio: During or before playback... • For MP3/DivX: During or before playback... -
Page 32: On-Screen Disc Operations
On-Screen Disc Operations Remote control Numeric buttons DVD/CD 3 ENTER 4,¢ REPEAT On-screen bars DVD Video Dolby DISC TITLE TITLE 2 CHAP CHAP 3 DVD-VIDEO 2/0.0ch TIME TIME CHAP. DVD Audio DISC GROUP 14 TRACK 23 DVD-AUDIO TIME TRACK PAGE SVCD TITLE DISC... -
Page 33: Operations Using The On-Screen Bar
Operations Using the On-screen Bar Ex.: Selecting a subtitle (French) for DVD Video: While a disc is selected as the source... Display the on-screen bar with the pull-down menu. Dolby DISC 3 TITLE 2 DVD-VIDEO 2/0.0ch Dolby DISC 3 TITLE TITLE 2 DVD-VIDEO 2/0.0ch... -
Page 34: Time Search
Select the repeat mode you want. Repeats all discs or all programmed tracks (not for some DVD Videos). Repeats a desired portion (see below). TITLE Repeats the current title*. GROUP Repeats the current group. DISC Repeats the current disc (except for DVD). -
Page 35: Operations On The Control Screen
Chapter/Track Search You can search for the chapter (DVD Video/DVD-VR) or track (DVD Audio) number to play. While playing, display the on-screen bar with the pull- down menu. Select CHAP. TRACK Display the pop-up window. Dolby DISC 2 TITLE TITLE 2 CHAP CHAP 3 DVD-VIDEO... -
Page 36: Unique Jpeg Operations
To select a group/track in the list Move the highlight bar to a desired item. • If you move the highlight bar while playing back an MP3 disc, the selected track starts playback automatically. To start playback Playback starts with the selected track. Pressing DVD/CD 3 also starts playback. -
Page 37: Timer Operations
Remote control CANCEL Timer Operations Setting the Daily Timer Using Daily Timer, you can wake up with your favorite music. You can store three Daily Timer settings; however, you can activate only one of the timers at a time. • To exit from the timer setting, press CLOCK/TIMER as required. - Page 38 4 For “TUNER FM” and “TUNER AM”: Select a preset channel (see page 11). • Select “FM – –” or “AM – –” for the last selected station. For “DISC”: Select the disc number, title/group/ playlist number, then the chapter/track number (see page 12).
-
Page 39: Setup Menu Operations
Setup Menu Operations Remote control ENTER SET UP Setup Menu Icons The icon for the selected Setup Menu will be highlighted. Ex.: LANGUAGE Setup Menu is selected. LANGUAGE MENU LANGUAGE ENGLISH AUDIO LANGUAGE ENGLISH SUBTITLE ON SCREEN LANGUAGE ENGLISH SELECT TO SELECT. -
Page 40: Language Setup Menu
Finish the setting. Repeat steps 3 to 4 to set other items on the same Setup Menu. Repeat steps 2 to 4 to set other items on another Setup Menu. To exit from the Setup Menu LANGUAGE Setup Menu You can select the initial languages for disc playback. You can also select the language shown on the TV screen while operating this System. -
Page 41: Audio Setup Menu
PICTURE SOURCE You can obtain optimal picture quality by selecting an appropriate option—picture source type (either video source or film source). Select one of the following: AUTO: Normally select this. When playing back a disc containing both video and film sources, the System automatically changes the processing to match to the picture type (film or video source) of the current chapter. -
Page 42: Others Setup Menu
D. (Dynamic) RANGE COMPRESSION You can compress the dynamic range (the difference between the loudest sound and the softest sound) to enjoy a powerful sound even at a low volume level when listening to Dolby Digital software. This is useful at night. •... -
Page 43: Operating The Tv
Remote control TV CH+/– SHIFT Operating the TV Operating TV You can operate the JVC’s TV using this remote control. To operate the TV To turn on or off the TV: TV/VIDEO TV VOL+/– To adjust the TV volume: To select the TV channel:... -
Page 44: Additional Information
Additional Information Learning More about This System Getting Started (see pages 3 to 6) Changing the Scanning Mode: • To enjoy the progressive video picture, connect a TV with the progressive video input using component video cord. Daily Operations—Playback (see pages 10 to 15) Listening to the Radio: •... - Page 45 • The sound may not be played back correctly—interrupted or degraded—due to your PC settings or PC specifications. * Microsoft , Windows 98, Windows Me, Windows 2000 and Windows trademarks of Microsoft corporation. Daily Operations—Sound&Other Adjustments (see pages 16 to 19) Adjusting the Volume: •...
-
Page 46: Maintenance
Setup Menu Operations (see pages 35 to 38) LANGUAGE Setup Menu: • When the language you have selected for “MENU LANGUAGE,” “AUDIO LANGUAGE,” or “SUBTITLE” is not recorded on a disc, the original language is used as the initial language. PICTURE Setup Menu—MONITOR TYPE: •... -
Page 47: Troubleshooting
Troubleshooting If you are having a problem with your System, check this list for a possible solution before calling for service. General: Adjustments or settings are suddenly canceled before you finish. ] There is a time limit. Repeat the procedure again. Operations are disabled. -
Page 48: Language Code List
Language Code List Afar Abkhazian Afrikaans Ameharic Arabic Assamese Aymara Azerbaijani Bashkir Byelorussian Bulgarian Bihari Bislama Bengali, Bangla Tibetan Breton Catalan Corsican Czech Welsh Danish Bhutani Greek Esperanto Estonian Basque Persian Finnish Fiji Faroese Frisian Irish Scots Gaelic Galician Guarani Gujarati Hausa Hindi... -
Page 49: Optical Digital Out Signals
OPTICAL DIGITAL OUT Signals DIGITAL AUDIO OUTPUT Playback disc DVD Video with 48 kHz, 16/20/24 bit Linear with 96 kHz, Linear PCM with Dolby Digital with DTS DVD Audio with 48/96/192 kHz, 16/20/24 bit Linear PCM with 44.1/88.2/176.4 kHz, 16/20/24 bit Linear PCM with Dolby Digital with DTS DVD-RW/RAM/ROM in DVD-VR... -
Page 50: Parts Index
Parts Index Refer to the pages to see how to use the buttons and controls. Remote control 26, 34, 39 11, 13, 17 – 19, 21, 23 – 25, 30, 31 10, 12, 13, 24, 26, 32 11, 13, 24 12, 24, 26, 32 10, 16, 39 11 –... -
Page 51: Specifications
Specifications Amplifier section Output power: 140 W (70 W + 70 W) at 6 Ω (10% THD) Analog input: AUX: Sensitivity/Impedance (at 1 kHz) 400 mV/47 kΩ USB input: USB Ver.1.1 Digital output: OPTICAL DIGITAL OUT: –21 dBm to –15 dBm (660 nm ±30 nm) VIDEO OUT: Color system Video (composite):... - Page 52 © 2005 Victor Company of Japan, Limited 0405MWMMDWBET...