Quadra-Fire SAPH-MBK-IPI Installation Manual
Quadra-Fire SAPH-MBK-IPI Installation Manual

Quadra-Fire SAPH-MBK-IPI Installation Manual

Hide thumbs Also See for SAPH-MBK-IPI:
Table of Contents

Advertisement

INSTALLER: Leave this manual with party responsible for use and operation.
OwNER: Retain this manual for future reference.
NOTICE: DO NOT discard this manual!
Models:
SAPH-MBK-IPI
SAPH-MBK-IPIL
SAPH-D-PMH-IPI
SAPH-D-PMH-IPIL
SAPH-D-MBK-IPI
SAPH-D-MBK-IPIL
SAPH-D-CSB-IPI
SAPH-D-CSB-IPIL
This appliance may be installed as an OEM installation
in manufactured home (USA only) or mobile home and
must be installed in accordance with the manufacturer's
instructions and the manufactured home construction
and safety standard, Title 24 CFR, Part 3280 or Standard
for Installation in Mobile Homes, CAN/CSA Z240MH, in
Canada.
This appliance is only for use with the type(s) of gas
indicated on the rating plate.
1
Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Installation Manual • 2343-980_R8 • 11/14
Installation Manual
Installation and Appliance Setup
R
wARNING: If the information in these
instructions is not followed exactly, a fire
or explosion may result causing property
damage, personal injury, or death.
• DO NOT store or use gasoline or other
flammable vapors and liquids in the vicinity of
this or any other appliance.
• What to do if you smell gas
- DO NOT try to light any appliance.
- DO NOT touch any electrical switch. DO
NOT use any phone in your building.
- Immediately call your gas supplier from a
neighbor's phone. Follow the gas supplier's
instructions.
- If you cannot reach your gas supplier, call
the fire department.
• Installation and service must be performed by
a qualified installer, service agency, or the gas
supplier.
!
HOT GLASS wIll CAUSE
BURNS.
DO NOT TOUCh glASS
UNtIl Cooled.
NEVER AllOw ChIldrEn
to toUCh glaSS.
In the Commonwealth of Massachusetts installation must
be performed by a licensed plumber or gas fitter.
See Table of Contents for location of additional
Commonwealth of Massachusetts requirements.
WARNING

Advertisement

Table of Contents
loading

Summary of Contents for Quadra-Fire SAPH-MBK-IPI

  • Page 1 This appliance is only for use with the type(s) of gas See Table of Contents for location of additional indicated on the rating plate. Commonwealth of Massachusetts requirements. Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Installation Manual • 2343-980_R8 • 11/14...
  • Page 2: Table Of Contents

    Rear Vent Conversion ..... . 32 B. Securing and leveling the appliance ....35 Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Installation Manual • 2343-980_R8 • 11/14...
  • Page 3: Installation Standard Work Checklist

    _____________________________________________________________________________________ _________________________________________________________________________________________________ _________________________________________________________________________________________________ Comments Communicated to party responsible ____________________ by ______________________on ___________ (Builder / Gen. Contractor/) (Installer) (Date)  = Contains updated information. 2343-982 Rev. B 2/14 Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Installation Manual • 2343-980_R8 • 11/14...
  • Page 4: Product Specific And Important Safety Information

    SaPh-d-MBK-IPIl (0-2000 FT) 22,500 16,500 compliance with the applicable electrical codes, when SaPh-d-CSB-IPIl (lP) it is installed in locations such as in bathrooms or near sinks. Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Installation Manual • 2343-980_R8 • 11/14...
  • Page 5: Requirements For The Commonwealth Of Massachusetts

    (1/2) in. in size, “GAS VENT DIRECTLY Connection section additional BELOw. KEEP CLEAR OF ALL OBSTRUCTIONS”. Commonwealth of Massachusetts requirements. Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Installation Manual • 2343-980_R8 • 11/14...
  • Page 6: Getting Started

    Non-corrosive leak check solution 1/2 - 3/4 in. length, #6 or #8 Self-drilling screws Caulking material (300ºF minimum continuous exposure rating) one 1/4 in. female connection (for optional fan). Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Installation Manual • 2343-980_R8 • 11/14...
  • Page 7: Framing And Clearances

    GAS LINE CORD Location Inches Millimeter Location Inches Millimeter 19-3/4 9-3/8 27-5/8 20-3/4 NOTE: Diagrams show gas appliance equipped without optional Blower, Part #GFK-160A. Figure 3.1 Appliance Dimensions Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Installation Manual • 2343-980_R8 • 11/14...
  • Page 8: Clearances To Combustibles

    Model Top of Side of Inside Outside pipe pipe corner wall vent SaPh-MBK-IPI 8-1/2 54-5/8 Inches SaPh-d-PMh-IPI SaPh-d-MBK-IPI 1388 Millimeters SaPh-d-CSB-IPI Figure 3.2 Appliance Locations Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Installation Manual • 2343-980_R8 • 11/14...
  • Page 9: Termination Location And Vent Information

    18/12 to 20/12 ..........7.5 over 20/12 to 21/12 ..........8.0 * 3 foot minimum in snow regions Figure 4.1 Minimum Height From Roof To Lowest Discharge Opening Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Installation Manual • 2343-980_R8 • 11/14...
  • Page 10: Chimney Diagram

    • Vinyl protection kits are suggested for use with vinyl siding. Figure 4.3 Minimum Clearances for Termination Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Installation Manual • 2343-980_R8 • 11/14...
  • Page 11: Approved Pipe

    • Roof flashing and a storm collar are required when venting passes through the roof. • Follow instructions provided with the venting for installation of these items. Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Installation Manual • 2343-980_R8 • 11/14...
  • Page 12: Use Of Elbows

    (flange of termination cap) (see Figure 4.3). • Vertical terminations are measured to bottom of termination cap. • horizontal pipe installed level with 1/4 inch rise per foot. Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Installation Manual • 2343-980_R8 • 11/14...
  • Page 13: Venting Guidelines For Horizontal Runs

    45º elbows: one 90º elbow or two 45º elbows must have a mini- mum vertical of 2 feet. 4 ft min. (1.22 m) Snorkel Kit Figure 4.6 Figure 4.7 Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Installation Manual • 2343-980_R8 • 11/14...
  • Page 14 7 ft., 6 in. 2.3 m 28 ft. 8.5 m 5 ft., 7 in. 1.7 m 30 ft. 9.1 m 4 ft., 7 in. 1.4 m Figure 4.8 Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Installation Manual • 2343-980_R8 • 11/14...
  • Page 15 4 ft., 6 in. 1.4 m 28 ft. 8.5 m 2 ft., 7 in. 787 mm 30 ft. 9.1 m 1 ft. 9 in. 533 mm Figure 4.9 Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Installation Manual • 2343-980_R8 • 11/14...
  • Page 16 24 ft. 7.3 m 1 ft., 6 in. 457 mm 28 ft. 8.5 m 11 in. 279 mm 30 ft. 9.1 m 11 in. 279 mm Figure 4.10 Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Installation Manual • 2343-980_R8 • 11/14...
  • Page 17 Top Vent - Vertical Termination = 30 ft. Max. (9.1 m) = 6 ft. Min. (1.8 m) No Elbow Figure 4.11 Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Installation Manual • 2343-980_R8 • 11/14...
  • Page 18 7.3 m 30 ft. 9.1 m 4 ft., 6 in. 1.4 m 28 ft. 8.5 m 34 ft. 9.1 m 2 ft., 7 in. 787 mm Figure 4.12 Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Installation Manual • 2343-980_R8 • 11/14...
  • Page 19 30 ft. 9.1 m 3 ft., 4 in. 1.0 m 24 ft. 7.3 m 30 ft. 9.1 m 1 ft., 6 in. 457 mm INSTALLED HORIZONTALLY Figure 4.13 Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Installation Manual • 2343-980_R8 • 11/14...
  • Page 20 Rear Vent Kit. Note: all horizontal vent pipe runs must have 1/4 inch rise per foot. NOTICE: An SLK-SNKD is required for this vent configuration. Figure 4.15 Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Installation Manual • 2343-980_R8 • 11/14...
  • Page 21 2 ft., 7 in. 787 mm 14 in. 357 mm Note: a derating orifice is required with this application and is included in the Rear Vent Kit. Figure 4.15 Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Installation Manual • 2343-980_R8 • 11/14...
  • Page 22 357 mm 1 ft., 6 in. 457 mm Note: a derating orifice is required with this application and is included in the Rear Vent Kit. INSTALLED HORIZONTALLY Figure 4.17 Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Installation Manual • 2343-980_R8 • 11/14...
  • Page 23 357 mm 6 ft. 1.8 m 40 ft. 12.2 m Note: a derating orifice is required with this application and is included in the Rear Vent Kit. Figure 4.18 Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Installation Manual • 2343-980_R8 • 11/14...
  • Page 24 1 ft., 6 in. 457 mm 36 ft., 4 in. 11.0 m Note: a derating orifice is required with this application and is included in the Rear Vent Kit. Figure 4.19 Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Installation Manual • 2343-980_R8 • 11/14...
  • Page 25 7. the connection between the appliance and the retro connector may be completed with sections of direct vent pipe. Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Installation Manual • 2343-980_R8 • 11/14...
  • Page 26 4 ft. (1m) Air VENT PIPE Intake section. 4 ft. (1m) of 3 in. (76mm) Flex Liner Co-Axial to Co-Linear Connector Air Intake Section Figure 4.24 Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Installation Manual • 2343-980_R8 • 11/14...
  • Page 27 Connect the flex to the coupler by using four sheet metal screws for each side. See Figure 4.27. Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Installation Manual • 2343-980_R8 • 11/14...
  • Page 28 See Figure 4.29. redrill larger holes on connector as needed. Be careful to ensure that the connector is centered in the opening and the mounting holes line up with the masonry wall. Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Installation Manual • 2343-980_R8 • 11/14...
  • Page 29 • May impair safe operation of this appliance or other appliances connected to the flue. • Vent this appliance directly outside. • Use separate vent system for this appliance. Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Installation Manual • 2343-980_R8 • 11/14...
  • Page 30: Vent Clearances And Framing

    *dimension is increased by 1/4 inch for every foot of horizontal pipe coming from the appliance. **as dimension “e” changes, dimension “a” must change accordingly. Figure 5.2 wall Penetration Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Installation Manual • 2343-980_R8 • 11/14...
  • Page 31: Ceiling Firestop/Floor Penetration Framing

    Figure 5.3 Installing Ceiling Firestop INSTALL ATTIC INSULATION SHIELDS BEFORE OR AFTER INSTALLATION OF VENT SYSTEM CEILING FIRESTOP CEILING FIRESTOP INSTALLED BELOW CEILING INSTALLED ABOVE CEILING Figure 5.4 Installing the Attic Shield Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Installation Manual • 2343-980_R8 • 11/14...
  • Page 32: Appliance Preparation

    Figure 8.) 3. Remove the inner pipe adapter Figure 5 shown in Figure 3 by removing six screws. Remove gasket and discard. Replace six screws into holes and tighten. Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Installation Manual • 2343-980_R8 • 11/14...
  • Page 33 See Figure 13. REMOVE SCREwS Figure 8. Attach inner collar adapter to rear flue vent. Figure 10. Remove Upper Baffle Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Installation Manual • 2343-980_R8 • 11/14...
  • Page 34 15. Using the 3/8 in. open end wrench, replace the main burner the firebox. orifice with the orifice included in the conversion kit. Use appropriate orifice for gas type. See Figure 14. 22. Reinstall front casting. 2342-925C Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Installation Manual • 2343-980_R8 • 11/14...
  • Page 35: Securing And Leveling The Appliance

    Normally, only one is required on the leg not touching the floor. Figure 8.11 2. Slide assembled nuts and bolts into slots on legs with the nuts on the bottom. Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Installation Manual • 2343-980_R8 • 11/14...
  • Page 36: Venting And Chimneys

    Use care when removing termination cap from slip pipe. If slip section seals are broken during removal of the termination cap, vent may leak. Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Installation Manual • 2343-980_R8 • 11/14...
  • Page 37: Assemble Slip Sections

    • Only outer pipes are sealed, sealing the inner flue is not required. • All unit collar, pipe, slip section, elbow and cap outer flues shall be sealed. Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Installation Manual • 2343-980_R8 • 11/14...
  • Page 38: Secure The Vent Sections

    Figure 7.7 Rotate Seams for Disassembly point to appliance. 120º Figure 7.5 Securing Vertical Pipe Sections Figure 7.8 Align and Disassemble Vent Sections 120º Figure 7.6 Securing Horizontal Pipe Sections Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Installation Manual • 2343-980_R8 • 11/14...
  • Page 39 2 in. (51 mm) MIN. BELOW FINISHED CEILING CUT HOLE 1/8 in. (3 mm) GREATER IN SIZE THAN PATTERN OF SUPPORT BOX AS IT IS PROJECTED ONTO ROOF LINE Figure 7.9 Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Installation Manual • 2343-980_R8 • 11/14...
  • Page 40: Vertical Termination Requirements

    • Caulk the perimeter of the flashing where it contacts the roof surface. See Figure 7.15. • Caulk the overlap seam of any exposed pipe sections that are located above the roof line. Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Installation Manual • 2343-980_R8 • 11/14...
  • Page 41 • tighten nut and make sure the collar is tight against the Caulk pipe section. • Caulk around the top of the storm collar. See Figure 7.15. Figure 7.15 Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Installation Manual • 2343-980_R8 • 11/14...
  • Page 42: Horizontal Termination Requirements

    • Rest the small leg on the extended heat shield on top of the pipe section to properly space it from the pipe section. Important Notice: heat shields may not be field constructed. Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Installation Manual • 2343-980_R8 • 11/14...
  • Page 43 HRC caps are available. When penetrating a brick wall, a brick extension kit is available for framing the brick. Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Installation Manual • 2343-980_R8 • 11/14...
  • Page 44: Electrical Information

    Verify proper operation after servicing. WARNING! Risk of Shock! Replace damaged wire with type 105º C rated wire. Wire must have high temperature insulation. Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Installation Manual • 2343-980_R8 • 11/14...
  • Page 45: Wiring Requirements

    FLAME IGNITER SENSE TO JUNCTION BOX (110V) MODULE FLAME MODULATION RC100 RC200 RC300 (OPTIONAL WALL CONTROLS) BATTERY PACK 6V DC Figure 8.1 IPI wiring Diagram Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Installation Manual • 2343-980_R8 • 11/14...
  • Page 46 Minimum 14-3 AWG with Ground Black Black White White Green Green Junction Box Power Switch Box Supply Wires Knockout Figure 8.2 Junction Box wired to wall Switch or BC10 Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Installation Manual • 2343-980_R8 • 11/14...
  • Page 47: Optional Fan Installation

    3. Slide temperature sensor switch/bracket assembly onto the 10-32 screw located on the underside of the appliance. Secure the bracket assembly with the wing nut provided. See Figure 8.4. Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Installation Manual • 2343-980_R8 • 11/14...
  • Page 48: Gas Information

    1/2 in. (13 mm) t-handle manual shut-off valve and flexible gas connector are connected to the 1/2 in. (13 mm) control valve inlet. • If substituting for these components, please consult local codes for compliance. Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Installation Manual • 2343-980_R8 • 11/14...
  • Page 49: Air Shutter Setting

    • Slide the wing nut to the left to open the air shutter. • tighten the wing nuts. NOTICE: If sooting occurs, provide more air by opening the air shutter. wING NUTS FOR SHUTTER ADJUSTMENT Figure 9.1 Air Shutter Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Installation Manual • 2343-980_R8 • 11/14...
  • Page 50: Appliance Setup

    2. Release both glass latches at the lower corners of the appliance. Remove glass from appliance. See Figure 10.2. TOP CASTING FRONT CASTING Figure 10.1 Remove Casting GLASS LATCHES Figure 10.2 Remove Glass Frame Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Installation Manual • 2343-980_R8 • 11/14...
  • Page 51: Install The Log Assembly

    If center ports are covered, sooting may occur. Adjust placement of mineral wool after fireplace has been turned off and is cool. Figure 5. Placement of Mineral wool 2342-935 Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Installation Manual • 2343-980_R8 • 11/14...
  • Page 52: Install Fixed Glass Assembly

    See Figure 10.1 and 10.2 for reference. Reinstall front casting. Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Installation Manual • 2343-980_R8 • 11/14...
  • Page 53: Reference Materials

    8-11/16 in. 1-1/2 in. 5-1/2 in. 12 in. 220 mm 38 mm 305 mm 146 mm SLP-FS SLP-WS Ceiling Firestop Wall Shield Firestop Figure 11.1 SLP Series Vent Components Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Installation Manual • 2343-980_R8 • 11/14...
  • Page 54 26 in. 660 mm 14-7/16 in. 367 mm DVP-HSM-B Extended Heat Shield 2-5/16 in. 14-7/16 in. 59 mm 367 mm SLP-WT-BK Wall Thimble-Black Figure 11.2 SLP Series Vent Components Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Installation Manual • 2343-980_R8 • 11/14...
  • Page 55 SLP-TVHW Horizontal Vertical Termination Kit Termination Cap 10-11/16 in. 271mm 28-1/2 in. 724 mm 13-1/2 in. 343 mm SLK-SNKD Snorkel Termination Cap Figure 11.3 SLP Series Vent Components Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Installation Manual • 2343-980_R8 • 11/14...
  • Page 56 (318 mm) SLP Low Profile Cap 7-3/8 IN. 187 mm 17-7/8 IN. 454 mm 14 IN. 356 mm 12 IN. 305 mm Figure 11.4 SLP Series Vent Components Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Installation Manual • 2343-980_R8 • 11/14...
  • Page 57 A. Vent Components Diagrams (continued) COAXIAL to COLINEAR VENTING LINK-DV30B 768-380A DV-46DVA-GCL Flex Liner Kit Stainless Steel Flex Pipe Coaxial/Colinear Appliance Connector lINKSQC-dV30 (CoPPeR) lINKSQB-dV30 (BlaCK) Figure 11.5 SLP Series Vent Components Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Installation Manual • 2343-980_R8 • 11/14...
  • Page 58: Accessories

    Please contact your Quadra-Fire dealer with any questions or concerns. For the location of your nearest Quadra-Fire dealer, please visit www.quadrafire.com. Printed in U.S.A. - Copyright 2014 Quadra-Fire • SAPH-MBK-IPI, SAPH-D-PMH-IPI, SAPH-D-MBK-IPI, SAPH-D-CSB-IPI Installation Manual • 2343-980_R8 • 11/14...

Table of Contents