Page 1
Order Number: MGCS011201C0 H21 (H22 for USA) Digital Imaging Systems DP-1510P / 1810P / 1810F / 2010E WARNING This service information is designed for experienced repair technicians only and is not intended for use by the general public. It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product.
Page 2
The contents of this Service Manual are subject to change without notice. Published in Japan.
(DA-SM08B/16B/64B/28B)....364 3.19. LFB PC Board........186 8.4. Installing the Automatic Document Feeder (DA-AS180) 3.20. SNS PC Board........187 for DP-1510P/1810P/2010E....365 3.21. MJR PC Board........188 8.5. Installing the Inverting Automatic 3.22. CST4 PC Board ........189 Document Feeder (DA-AR201) 3.23. LANB PC Board........192 for DP-2010E ........
Page 4
Table of Contents Schematic Diagram ......406 9.1. General Circuit Diagram System Circuit............406 9.2. SC PC Board ........411 9.3. LPC3 PC Board ........441 9.4. ADF PC Board ........448 9.5. CCD PC Board ........450 9.6. CST4 PC Board ........451 9.7. PNL6 PC Board ........452 9.8.
DP-1510P/1810P /1810F/2010E 1 Specifications Table Note: DP-1510P/2010E model is limited to certain destinations only. 1.1. Copy Function Description Items Remarks DP-1510P DP-1810P DP-1810F DP-2010E Basic Specifications 1 Type Desktop 2 Platen Fixed 3 Original Position Left / Inner 4 Recording Paper Path...
Page 6
DP-1510P/1810P /1810F/2010E Description Items Remarks DP-1510P DP-1810P DP-1810F DP-2010E 17 Paper Feed Front Loading Universal Paper Tray Paper Tray 550 sheets x 1 Capacity LTR / A4 : 20 lb (75 g/m (DP-2010E-PU: 550 sheets x 2) Auto Size Setting...
Page 7
DP-1510P/1810P /1810F/2010E Description Items Remarks DP-1510P DP-1810P DP-1810F DP-2010E 99 lb 113 lb Main Unit only. 91 lb (41 kg) (45 kg) (51kg) For USA and Canada 29 Weight 99 lb 93 lb 91 lb (41 kg) For Other Destinations...
Page 8
DP-1510P/1810P /1810F/2010E Description Items Remarks DP-1510P DP-1810P DP-1810F DP-2010E 10 Paper Transport Unit 11 Automatic Duplex Unit 12 Counter Only the Harness Kit is Key Counter Capability supplied as an option kit. 13 Dehumidifier Option Supplied as a Service Part.
Page 10
DP-1510P/1810P /1810F/2010E Description Items Remarks DP-1510P DP-1810P DP-1810F DP-2010E Check / Slip Mode Copy Account Display Mode 3 Control Panel 20 x 2 Display Alphanumeric LCD Status Lamp Original Size Copy Size Keypad Clear Stop Start Energy Saver Multi Size Feed Same widths only.
Page 11
DP-1510P/1810P /1810F/2010E Description Items Remarks DP-1510P DP-1810P DP-1810F DP-2010E Error Code Finishing Warning Indicators Add Toner (LED Indication only) Toner Waste Container Full Add Paper (No Paper) (LED Indication only) Add Paper Paper Jam Indication (LED Indication only) Paper Jam Location...
Page 12
DP-1510P/1810P /1810F/2010E Description Items Remarks DP-1510P DP-1810P DP-1810F DP-2010E Developer Life Toner Waste Container Dehumidifier Supplied as a Service Part Manual Add Toner Toner Bottle replacement 7 Feeder System Paper Tray (Standard / Option) Paper Size Setting Universal & Fixed by Screw...
Page 13
DP-1510P/1810P /1810F/2010E Description Items Remarks DP-1510P DP-1810P DP-1810F DP-2010E PM Cycle 1 Major PM 120 k 2 Minor PM (Cleaning) 60 k Packing Configuration 28.9 x 28.9 x Main Unit only. 30.1 x 30.1 x 28.9 x 30.1 x 23.4 in 25.6 in...
DP-1510P/1810P /1810F/2010E 1.2. Fax, Printer and Internet Fax Functions 1.2.1. Fax Function Note: DP-1810F model only. Description Items Remarks DP-1810F Main Specifications 1 Compatibility ITU-T Std & Non-Std (MGCS) 2 PSTN Line Port Yes (1) 3 Leased Line Port 4 V.24 Line Port 5 Modem Speed 33.6 - 2.4kbps...
Page 15
DP-1510P/1810P /1810F/2010E Description Items Remarks DP-1810F Printer Mechanism 1 Recording Method 18 ppm 2 Recording Speed (A4 horizontal) 3 Recording Resolution Fax 406 x 391 dpi Ledger size is transmitted as A3 size for N. American Ledger / Legal / Letter / model.
Page 16
DP-1510P/1810P /1810F/2010E Description Items Remarks DP-1810F 14 Pulse to Tone Change 15 Flash Key 16 Handset Option Transmission Features 1 Direct Transmission 2 Memory Transmission Page Retransmission Quick Memory Transmission Multi-Station Transmission Max. 190 stations (Sequential Broadcasting) Direct Deferred ADF Deferred Transmission...
Page 18
DP-1510P/1810P /1810F/2010E Description Items Remarks DP-1810F Special Communications 1 Password XMT / RCV 2 Selective Reception TSI Check 3 Relay XMT Request 4 Relay XMT Center 5 Confidential XMT / Polling 6 Confidential Center 7 Mailbox XMT / Polling 8 Mailbox Center Max.
Page 19
DP-1510P/1810P /1810F/2010E 1.2.2. Printer Function Description Remarks Items DP-1510P DP-1810P DP-1810F DP-2010E Interface Centronics Parallel I/F Centronics Parallel Interface (IEEE-1284) Ethernet 10Base-T/ Requires the Optional 2 LAN (Network) 100Base-TX Internet Fax Kit. 3 USB Port 4 IEEE-1394 Printer Function LDR, LGL, LTR, LTR-R, INV,...
Page 20
DP-1510P/1810P /1810F/2010E Description Remarks Items DP-1510P DP-1810P DP-1810F DP-2010E Scanning Function LAN : 256 Halftone Shades 256 Halftone Shades, Gray Scale (Local with Error Diffusion. 1 Halftone Connection) Requires the Optional Internet Fax Kit. 2 Max. Document Size Ledger, A3...
Page 21
DP-1510P/1810P /1810F/2010E 1.2.3. Internet Fax Function Note: DP-1810F model only. Description Items Remarks DP-1810F Main Specifications 1 Communication Protocols TCP / IP SMTP / MIME 2 Max. Modem Speed 3 Coding Scheme MH / MMR 400 dpi : MMR only...
Page 22
DP-1510P/1810P /1810F/2010E Description Items Remarks DP-1810F 3 Internet Fax Server Features iFAX → iFAX → G3FAX Internet Fax Relay XMT PC → iFAX → G3FAX Email Relay MXT Received Fax / Email Local print available Forward PC to FAX Transmission Using Sub-Address.
DP-1510P/1810P /1810F/2010E 1.3. System Combination For DP-1510P/1810P ADF or Platen Cover ADF PC Board Document Sensor Scanner Unit and Motor Panel Main PC Board (PNL PC Board) (SC PC Board) PCL6 Emulation Kit (PDL PC Board) Parallel Port Interface 10/100 Ethernet Interface...
Page 24
DP-1510P/1810P /1810F/2010E For DP-1810F ADF PC Board Document Sensor Scanner Unit Motor Panel Main PC Board Handset (PNL PC Board) (SC PC Board) (MJR PC Board) PCL6 Option Emulation Kit Parallel Port (PDL PC Board) Interface Memory CARD 2, 4, 8M...
Page 25
DP-1510P/1810P /1810F/2010E For DP-2010E i-ADF, ADF or Platen Cover ADF PC Board Document Sensor Scanner Unit Motor Panel Main PC Board (PNL PC Board) (SC PC Board) PCL6 Emulation Kit (PDL PC Board) Parallel Port Interface 10/100 Ethernet Interface Dehumidifier...
DA-AS180 Standard for DP-1810F Inverting Automatic Document Feeder DA-AR201 Only for DP-2010E (i-ADF) 2nd/4th Paper Feed Module DA-DS182 3rd Paper Feed Module DA-DS183 Except for DP-1510P/1810P 1.4.2. Supplies Part Name Part Number Remarks Toner Bottle DQ-TU10C Sales Route OPC Drum DQ-H045B Edition 2.0...
DP-1510P/1810P /1810F/2010E 1.5. External View For DP-1510P/1810P/2010E Rear View Top View (For USA only) Product complies with DHHS Rules 21 CFR Subchapter J in effect at date of manufacture. Manufacturer's name and address Factory ID 23.1 in (588 10 mm...
DP-1510P/1810P /1810F/2010E For DP-1810F Rear View Top View (For USA only) Product complies with DHHS Rules 21 CFR Subchapter J in effect at date of manufacture. 23.1 in Manufacturer's name and address Factory ID (588 10 mm Right View Left View...
Page 29
DP-1510P/1810P /1810F/2010E 1.5.1. Serial Number Contents The contents of the 11-digit Serial Number is as follows: Sequential Production Number 5-Digit Sequential Production Number 00001 ~ 99999 = 1 ~ 99,999 units A0001 ~ Y9999 = 100,000 ~ 329,976 units (Letters “I” and “O” are skipped)
DP-1510P/1810P /1810F/2010E 1.6. Control Panel DP-1510P For EURO and Other Destinations DP-1810P For USA and Canada For Other Destinations Edition 2.0 APR 2002...
Page 31
DP-1510P/1810P /1810F/2010E DP-1810F For All Destinations DP-2010E For USA and Canada For Other Destinations Edition 2.0 APR 2002...
DP-1510P/1810P /1810F/2010E 2 Disassembly Instructions 2.1. General Disassembly Flowchart 2-2-1 AC Power Cord (1502) 2-2-2 ADF Unit Separation Rubber (428) Paper Feed Roller (679) Pre Feed Roller (420) ADF PC Board (1406) ADF Motor (437) Feed Roller (409) SNS PC Board (134)
Page 33
DP-1510P/1810P /1810F/2010E 2-2-4 Control Panel Unit Speaker (125) LCD Cover (201) Panel Cover (202) PNL6 PC Board (1416) PNL2 PC Board (1417) 2-2-5 Scanner Unit Left Platen Cover (113) Right Platen Cover (112) Glass L Assembly (117) Glass S (116)
DP-1510P/1810P /1810F/2010E 2.2. Disassembly Instructions 2.2.1. Power Cord, Recording Paper Tray, Process Unit (1) Turn the Power Switch to the OFF (O) position. (2) Disconnect the AC Power Cord (1502). (3) Remove the Paper Tray. (4) Open the Right Cover (601).
Page 36
DP-1510P/1810P /1810F/2010E 2.2.2. ADF Unit (1) Open the ADF Cover (418) and release the ADF Cover Stopper (414). (2) Remove the Pad Cover (427). (3) Remove the Separation Rubber (428). (4) 2 Screws (19). (5) Remove the ADF Cover (418).
Page 37
DP-1510P/1810P /1810F/2010E (11) Remove Roller Holder (430) Assembly. (12) (12) Remove the Paper Feed Shaft Assembly (11) (433). Note: When re-installing, make sure that the Roller Holder (430) Assembly is properly placed on the ADF Unit. (13) Remove Paper Feed Roller (679) and D26 D (13) Gear (429).
Page 38
DP-1510P/1810P /1810F/2010E Note: When re-installing the ADF Rear Cover (301), make sure that the ADF Harness is properly placed as shown in the illustration. (17) 1 Screw (19). (17) (18) (18) Remove the ADF PC Board Cover (453). (19) Release the Clamp from ADF Unit.
Page 39
DP-1510P/1810P /1810F/2010E (26) Disconnect 5 Harnesses (1836, 1837, 1838, 1839, 1840) on the ADF PC Board. (6 (26) (26) connectors) (27) 2 Screws (19). (28) Remove the ADF PC Board (1406). (28) (27) (29) Release the Harness from the Clamp.
Page 40
DP-1510P/1810P /1810F/2010E (35) Remove 2 Drive Belts (444, 445). (36) Remove the S27 Pulley (443). (37) Remove the Bushing (410). (37) (38) Remove the Snap Ring (B9). (36) (39) Remove the S27 Pulley (443). (40) Remove the Bushing (410). (41) (41) Release the clips and remove the Switch (724).
Page 41
DP-1510P/1810P /1810F/2010E (52) 5 Screws (19). (56) (58) (53) Remove the Center Bracket (452). (54) Release the NP Actuator Spring (408). (52) (55) Remove the NP Actuator (407). (56) Disconnect the Harness (1837). (2 Connectors) (57) (57) Remove the Photo Sensor (604).
Page 42
DP-1510P/1810P /1810F/2010E <Cleaning the Rollers and Rubber> (1) Open the ADF Cover. (2) Release the Stopper. (3) Clean the Separation Rubber, Feed Roller, Pre Feed Roller and Paper Feed Roller with a soft cloth, saturated with isopropyl alcohol. <Cleaning the Exit Roller>...
Page 43
DP-1510P/1810P /1810F/2010E 2.2.3. Cover Assembly (1) 3 Screws (19). (2) Release the 3 Latch Hooks and Remove the Front Cover (101). (3) Remove the Inner J Cover (103). Latch Hooks (4) 4 Silver Screws (B1). (5) Remove the Left Side Cover (104).
Page 44
DP-1510P/1810P /1810F/2010E (14) Remove the Right Cover Stopper (625). (15) Remove the Front Arm (657). (14) (15) (16) Remove the Right Cover (601) Assembly. Note: (16) Remove the front fulcrum (A) and then pushing the Right Cover (601) Assembly toward the rear, remove the rear fulcrum.
Page 45
DP-1510P/1810P /1810F/2010E 2.2.4. Control Panel Unit (1) 2 Silver Screws (B1). Latch Hooks (2) 2 Screws (19). (3) Release 2 Latch Hooks and remove the Control Panel Assembly. (4) Disconnect the Harness (1801) on the PNL6 PC Board (CN201). <Following steps (5)~(11) is for DP-1810F only>...
Page 46
DP-1510P/1810P /1810F/2010E (12) 1 Screw (19). (12) (13) Remove the Panel Bracket (233). (13) (14) Disconnect the Harness (1852) on the PNL6 PC Board (CN1). Note: (14) During re-assembly, reconnect this Harness to PNL6 PC Board prior to securing the board with the screws.
Page 47
DP-1510P/1810P /1810F/2010E 2.2.5. Scanner Unit (1) 2 Silver Screws (B1). (2) Remove 2 Angle Plates (305). (3) Open the ADF Unit. (4) 3 Silver Screws (B1). (5) Remove the Left Platen Cover (113). (6) 3 Silver Screws (B1). (7) Remove the Right Platen Cover (112).
Page 48
DP-1510P/1810P /1810F/2010E (11) Remove the Control Panel Unit (12) (Refer to 2.2.4.). (12) 5 Screws (19). (12) (13) Remove the F/R Scanner Frame (532). (13) (14) Move the Lamp Base Bracket. (15) (16) (15) 2 Screws (19). (16) (16) Remove 2 Lamp Plate Springs (524).
Page 49
DP-1510P/1810P /1810F/2010E (22) 2 Screws (19). (22) (23) Remove the Inverter PC Board (564). (23) (22) (24) 2 Screws (19). (25) Remove LFB PC Board (1414) Assembly and (24) LFB PC Board (1414). (26) Disconnect the Harness on the LFB PC Board.
Page 50
DP-1510P/1810P /1810F/2010E (32) Remove the Rear Cover and Rear Plate. (Refer to 2.2.3.) (33) Remove the E-Ring (5Y). (34) Remove the Synchronous Belt (118). (35) Remove the MXL34 Pulley (119). (35) (34) (33) (36) 3 Screws (19). (37) Disconnect the Harness (1807) on the Scanning (38) Motor.
Page 51
DP-1510P/1810P /1810F/2010E (42) Release the Harnesses from the Clamps. (44) (42) (43) Disconnect the Harness (1805). (43) (44) Disconnect the Harness (1803). (45) 1 Screw (19). (45) (46) Remove the Front Platen Frame Bracket (127). (48) (47) 1 Screw (19).
Page 52
DP-1510P/1810P /1810F/2010E 2.2.6. LSU, Fan, LVPS, HTC PC Board (1) 2 Screws (19). (2) Disconnect 2 Harnesses (1809, 1824). (3 connectors) (3) Remove the LSU (710). Note: Do not touch the RED Screw (A) of LSU Damper as illustrated. Note: When re-installing the LSU, put the latch under the Plate Spring.
Page 53
DP-1510P/1810P /1810F/2010E (9) 1 Screw (E5). (10) Disconnect the Harness (1814). (10) (11) Remove the Fan (808). (11) (12) 3 Screws (19). (13) (13) Remove the Lower Fan Bracket (805). (12) (12) (14) Disconnect the Harness (1830) on the LVPS (CN60).
Page 54
DP-1510P/1810P /1810F/2010E (19) 6 Screws (19). (19) (20) Remove the LVPS (1404). Note: When re-installing the LVPS, install the upper 4 Screws first and then the remaining 2 Screws. (20) (19) (21) Disconnect all Harnesses on the HTC PC Board...
Page 55
DP-1510P/1810P /1810F/2010E 2.2.7. ILS, Fan (1) 2 Screws (E6). (2) Remove 2 Micro Switch (813) and Disconnect 2 Harnesses (1823). (3) 1 Screw (24). (4) Remove the 3 Fly Wheels (1101). Note: When re-installing the Fly Wheels, make sure that the Imprinted Marks are facing outward.
Page 56
DP-1510P/1810P /1810F/2010E 2.2.8. SC PC Board, LPC3 PC Board, MJR PC Board (For DP-1810F Only) (1) Disconnect 2 Harnesses (1866, 1867) (2) 2 Screws (19). (3) Remove the MJR PC Board (1421). (4) Remove the Locking Spacer (824). (5) Disconnect all Harnesses on the SC PC Board (1401).
Page 57
DP-1510P/1810P /1810F/2010E Note: When re-installing the SC PC Board. (9) Release 2 Latch Hooks and remove the Card Guide (816). (10) Move 2 Lock Springs as illustrated. (11) 2 Screws (20). (12) (11) (12) Reinstall the Card Guide (816) as illustrated.
Page 58
DP-1510P/1810P /1810F/2010E 2.2.9. Drive Motor, HVPS, Solenoid, Drive Unit <Drive Motor> (1) Release the Harness (1818) from the Clamp. (2) Disconnect the Harness (1818) on the Drive Motor Assembly. (3) 4 Screws (19). (4) Remove the Drive Motor. <HVPS, Solenoid and Drive Unit>...
Page 59
DP-1510P/1810P /1810F/2010E (12) 2 Screws (19). (13) Remove the CST Cover (716) Assembly. (13) (12) (14) Release the Solenoid Harness from 2 Clamps. (14) (15) Remove the Rear Plate. (Refer to 2.2.3.) (16) Release the Solenoid Harness from Clamp and Disconnect it.
Page 60
DP-1510P/1810P /1810F/2010E (19) 2 Screws (19). (20) Remove the Solenoid Assembly. (20) (19) (21) 1 Screw (19). (22) Remove the Solenoid (1102). (21) (22) (23) 2 Screws (19). (24) Remove the Fan Assembly. (24) (23) (25) Push down the Latch Hook with a Straight Edge Screwdriver.
Page 61
DP-1510P/1810P /1810F/2010E (27) Disconnect the Harnesses (1229, 1856) on the LPC3 PC Board. (28) (28) Release the Harness (1818) from the Clamp. (30) (29) Disconnect the Harness (1818) on the Drive Motor Assembly. (29) (30) 4 Screws (19). (31) (31) Remove the Drive Unit.
Page 62
DP-1510P/1810P /1810F/2010E (4) Install the Gear and the Snap Ring. (5) Install the other Gear and Snap Ring. Edition 2.0 APR 2002...
Page 63
DP-1510P/1810P /1810F/2010E 2.2.10. AC Inlet (1) 1 Silver Screw (B1). (2) Remove the Inlet Cover (751). (3) 2 Screws (35). (4) Disconnect 2 Harnesses (1828). (5) Remove the AC Inlet Assembly. (6) Disconnect the Harness (1842). (7) Remove the AC Inlet (807).
Page 64
DP-1510P/1810P /1810F/2010E 2.2.11. Fuser Unit (1) Open the Right Cover (601) Assembly. (2) 2 Screws (19). (3) Remove the Front Connector Cover (714). (4) Remove the Rear Connector Cover (713). (5) 2 Screws (4N). (6) Remove 2 Harnesses (1829). (7) Remove 2 Harnesses (1813).
Page 65
DP-1510P/1810P /1810F/2010E (14) Remove the Fuser Lamp (924). Note: Do not Touch the glass portion of the Fuser Lamp with bare hands. Grease from finger prints will shorten its life cycle, use isopropyl alcohol to clean finger prints. (14) (15) Remove the Snap Ring (B9).
Page 67
DP-1510P/1810P /1810F/2010E <Cleaning Separator> (1) Clean the Separators with a soft cloth, saturated with isopropyl alcohol. (2) Clean 2 Separation HR Sheets with a soft cloth, saturated with isopropyl alcohol. (26) Remove 3 Separator Springs (953). (27) Remove 5 Separators (923).
Page 68
DP-1510P/1810P /1810F/2010E (30) 1 Screw (23). (30) (31) 1 Screw (19). (31) (33) (32) Release the Stopper and disconnect the Harness. (33) Remove the Harness Guide (906). (32) <Cleaning Thermistor Assembly, Thermostat> (1) Clean the Thermistor Assembly (944) with a soft cloth, saturated with isopropyl alcohol.
Page 69
DP-1510P/1810P /1810F/2010E (40) 5 Screws (19). (40) (41) Remove the Roller Bracket (909). Note: When re-installing, install the Screw A first, then the remaining 4 Screws. (41) (40) A (40) (42) Remove the Fuser Roller (913). (42) (43) Remove 2 C-Rings (938).
Page 70
DP-1510P/1810P /1810F/2010E 2.2.12. Registration Roller, Toner Sensor (1) Remove the Rear Cover. (Refer to 2.2.3.) (2) Remove 3 Fly Wheels. (Refer to 2.2.7.) (3) Remove the HVPS, Snap Ring and Clutch. (Refer to 2.2.9.) (4) Remove the Snap Ring (B9).
Page 71
DP-1510P/1810P /1810F/2010E (14) 1 Screw (19). (15) Disconnect the Harness (1827). (14) (16) Remove the Toner Sensor Spring (1148). (16) (15) (17) Remove the Toner Sensor (1147). (17) (18) Disconnect the Harness (1827). (19) (18) (19) (18) (19) Remove 2 Photo Sensors (604).
Page 72
DP-1510P/1810P /1810F/2010E 2.2.13. Bias Transfer Roller <Cleaning the Registration Roller, Duplex Transfer Roller and Pinch Roller> (1) Clean the Registration Roller, Duplex Transfer Roller and Pinch Roller with soft cloth, saturated with isopropyl alcohol. (2) Clean the Bias Transfer Roller with soft dry Cloth.
Page 73
DP-1510P/1810P /1810F/2010E (8) 2 Screws (C8). (9) Remove the BTR Guide (642). (10) Release 2 Latch Hooks and remove the BTR Gear (644). (10) (11) Remove the Bias Transfer Roller (648). Note: (11) When re-installing the Bias Transfer Roller (648),...
Page 75
DP-1510P/1810P /1810F/2010E 2.2.14. Paper Feed Module <Cleaning the Paper Feed Roller and C25 Gear Roller> Clean the Paper Feed Roller and C25 Gear Roller with soft cloth, saturated with isopropyl alcohol. (1) Release the Latch hook and remove the C25 Gear Roller (1207) and Reverse Clutch (1212).
Page 76
DP-1510P/1810P /1810F/2010E (2) Clean the Intermediate Roller (1617). Note: 3rd/4th Paper Feed Modules are as the same steps (1)~(2). Edition 2.0 APR 2002...
Page 77
DP-1510P/1810P /1810F/2010E 2.2.15. Lift Motor Assembly (1) Remove 3 Fly Wheels. (Refer to 2.2.7.) (2) Remove the HVPS. (Refer to 2.2.9.) (3) Disconnect the Harness on the LPC3 PC Board (CN706). (4) Release the Harness from the Clamps. (5) 2 Screws (19).
Page 78
DP-1510P/1810P /1810F/2010E 2.2.16. Process Unit (1) Open the Right Cover. (2) Open the Front Door Cover. (3) Remove the Toner Waste Container by slowly pulling it towards the left as illustrated. (4) Seal the Container with the enclosed cap and dispose of it properly.
Page 79
DP-1510P/1810P /1810F/2010E (8) Unlock the Front OPC Bushing Assembly (1003, 1023) by turning it clockwise. (9) Push the OPC Drum forward from the rear end as illustrated. (10) (10) Remove the Front OPC Bushing Assembly (1003, 1023). (11) Lift the OPC Drum (1001) as illustrated, holding the right side where the Front OPC Bushing Assembly was installed.
Page 80
DP-1510P/1810P /1810F/2010E Note: When re-installing the Bias Charge Roller Holder Assembly, install the Charge Holder (1037) first as shown in (A) and then the Charge Bushing (1038) with the Charge Spring (1039) as shown in (B). (14) Remove the Scoop Sheet (1033).
Page 81
DP-1510P/1810P /1810F/2010E Note: 1. When re-installing, install 2 CL Sponges (1030) first as shown in (A), then the CL Blade Assembly (1035) next as shown in (B), then the Front CL Felt (1031) and Rear CL Felt (1032) as shown in (C) and lastly attach the Scoop Sheet (1033) as shown in (D).
Page 82
DP-1510P/1810P /1810F/2010E (22) Remove the Mag Roller Joint (1047). (23) Remove the Charge Plate D (1059). (24) Remove the Mag Roller Stopper (1046) by (24) gently pushing it downwards. (23) (22) (25) Remove the Mag Roller (1048). Note: 1.Do not touch the surface of the Mag Roller.
DP-1510P/1810P /1810F/2010E 3.4. Updating the Firmware This machine is equipped with an F-ROM (Flash ROM). F-ROM offers the flexibility of quick and easy firmware updates, creation of a master firmware card, backup and restore of firmware and machine parameters. The following is the basic procedure to update the firmware of the machine. The details are described in the Firmware Update Tool Operating Instructions.
Page 93
DP-1510P/1810P /1810F/2010E 3.4.2. Updating the Host Firmware using the Master Firmware Card A. When a 4 MB Flash Memory Card was used 1. Before starting, print the F5 & F6 Parameters (Copier) Lists. 2. Turn the Power Switch to the OFF (O) position.
Page 94
1. Before starting, print the F5 & F6 Parameters (Copier) Lists. 2. Connect the machine to the PC with a Parallel Printer Cable. 3. Install the Panasonic Firmware Programming Wizard software to the PC. (Refer to the Firmware Update Tool Operating Instructions) 4.
Page 95
DP-1510P/1810P /1810F/2010E 3.4.6. Erasing the Master Firmware Card 1. Turn the Power Switch to the OFF (O) position. 2. Install the Master Firmware Card into the machine. 3. Turn the Power Switch to the ON (I) position. 4. Press “FUNCTION”, “ORIGINAL SIZE” keys and then Key “3” on the keypad sequentially.
DP-1510P/1810P /1810F/2010E 3.5. Glossary of Electrical Abbreviations Glossary of Electrical Abbreviations Signal Name Description +12V +12 VDC Power Supply +24V +24 VDC Power Supply +24VD1 +24 VDC Power Supply +24VF +24 VDC Power Supply +24VM +24 VDC Power Supply +24VOPF +24 VDC Power Supply +3.3V...
Page 97
DP-1510P/1810P /1810F/2010E Glossary of Electrical Abbreviations Signal Name Description AL[2] Address Signal AL[3] Address Signal AL[4] Address Signal AL[5] Address Signal AL[6] Address Signal AL[7] Address Signal AL[8] Address Signal AL[9] Address Signal BATVOL Battery Voltage Battery Voltage BAT/BUZCLK Buzzer Clock...
Page 98
DP-1510P/1810P /1810F/2010E Glossary of Electrical Abbreviations Signal Name Description BMD[25] Data Signal BMD[26] Data Signal BMD[27] Data Signal BMD[28] Data Signal BMD[29] Data Signal BMD[3] Data Signal BMD[30] Data Signal BMD[31] Data Signal BMD[37] Data Signal BMD[38] Data Signal BMD[4]...
Page 99
DP-1510P/1810P /1810F/2010E Glossary of Electrical Abbreviations Signal Name Description DATA1 Data Signal DATA2 Data Signal DATA3 Data Signal DATA4 Data Signal DATA5 Data Signal DATA6 Data Signal DATA7 Data Signal DEVELOPMENT Development Signal (High Voltage) Development Control AC+DC Output DRCLK...
Page 100
DP-1510P/1810P /1810F/2010E Glossary of Electrical Abbreviations Signal Name Description KIN[7] Key Scan Signal L+5V Laser Circuit +5 VDC Power Supply Line Signal L1 (R) Ground Line Signal L2 (T) Line Transformer Input Signal LASERPOW Laser Power Control LDBTHP Toner Bottle HP Sensor Signal...
Page 101
DP-1510P/1810P /1810F/2010E Glossary of Electrical Abbreviations Signal Name Description nADF2 2nd Paper Tray Feed Roller Drive Signal nAEJC Original Eject Detection Signal nAKEEP1 Reversing 1 Guide Solenoid Control Signal nAKEEP2 Reversing 1 Guide Solenoid Control Signal nANG Platen Cover Angle...
Page 102
DP-1510P/1810P /1810F/2010E Glossary of Electrical Abbreviations Signal Name Description nCTON Ring Detection Signal nDADFON ADF Option Detection Signal nDUPKEP2 Duplex Keep Solenoid Drive Signal nDUPSEN1 Duplex Sensor1 Signal nESEN Inner Under Tray Paper Exit Signal Data Available / Error Condition nFAULT (Peripheral→Host)
Page 103
DP-1510P/1810P /1810F/2010E Glossary of Electrical Abbreviations Signal Name Description nMRCLH2 2nd Paper Tray Intermediate Roller Clutch Drive Signal Read Enable nOPB1 Option Detection Signal nOPB2 Option Detection Signal nOPB3 Option Detection Signal nOPDUP Duplex Unit Option Detection nOPON Option Detection Signal...
Page 104
DP-1510P/1810P /1810F/2010E Glossary of Electrical Abbreviations Signal Name Description nWEH High Enable nWEL Write Low Enable OUTA Motor Control Signal OUTB Motor Control Signal pAB1SN ADF Cover Open Detection Signal pADF2A 2nd Feed Roller Drive Signal pADF3A 3rd Feed Roller Drive Signal...
Page 105
DP-1510P/1810P /1810F/2010E Glossary of Electrical Abbreviations Signal Name Description PNLTXD Transmission Signal pOP1RST Reset Signal pOP2RST Reset Signal pOP3RST Reset Signal pPDLREQ Direct Memory Access Data Request Signal pUPLIMIT2 2nd Lift DC Motor Ready Signal pUPLIMIT3 3rd Lift DC Motor Ready Signal...
Page 106
DP-1510P/1810P /1810F/2010E Glossary of Electrical Abbreviations Signal Name Description VOUT1 Graphic Data Output VOUT2 Graphic Data Output VPP2 Not Used Edition 2.0 APR 2002...
DP-1510P/1810P /1810F/2010E 3.6. SC PC Board SC PCB Signal Name Destination Signal Waveform Function Pin No. CN3-1 +5VP ADF PCB +5 VDC Power Supply CN21-1 CN3-2 MGND ADF PCB Ground CN21-2 CN3-3 ADF PCB Ground CN21-3 CN3-4 +24V ADF PCB...
Page 108
DP-1510P/1810P /1810F/2010E SC PCB Signal Name Destination Signal Waveform Function Pin No. CN3-12 nAB1SN ADF PCB Read Point Detection Signal CN21-12 L: Detect CN3-13 nAEJC ADF PCB Original Eject Detection CN21-13 Signal L: Detect CN3-14 nAREV ADF PCB ADF Exit Cover Open...
Page 109
DP-1510P/1810P /1810F/2010E SC PCB Signal Name Destination Signal Waveform Function Pin No. CN3-23 nACLH3 ADF PCB Inverting Roller Clutch CN21-23 Control Signal CN3-24 nACLOCKAD1 ADF PCB ADF Motor Control Clock CN21-24 Signal CN3-25 nASTROAD1 ADF PCB ADF Motor Control Strobe...
Page 110
DP-1510P/1810P /1810F/2010E SC PCB Signal Name Destination Signal Waveform Function Pin No. CN3-35 ADF PCB Ground CN21-35 CN3-36 nDADFON ADF PCB ADF Option Detection CN21-36 Signal H: ADF Option Installed i-ADF L: i-ADF Option Installed CN3-37 +24V ADF PCB +24 VDC Power Supply...
Page 111
DP-1510P/1810P /1810F/2010E SC PCB Signal Name Destination Signal Waveform Function Pin No. CN8-6 nOUTB Stepping Motor Motor Control Signal +24V SC PCB Signal Name Destination Signal Waveform Function Pin No. CN9-1 nFLON INV PCB Inverter Ground +5V (H) CN1-1 0V (L)
Page 112
DP-1510P/1810P /1810F/2010E SC PCB Signal Name Destination Signal Waveform Function Pin No. CN10-7 nORI Home Position Home Position Detection +5V (H) Sensor Signal 0V (L) CN10-8 Home Position Ground Sensor CN100 SC PCB Signal Name Destination Signal Waveform Function Pin No.
Page 113
DP-1510P/1810P /1810F/2010E SC PCB Signal Name Destination Signal Waveform Function Pin No. CN100-9 nHSYNC LPC3 PCB Horizontal Synchronous +5V(H) CN704-9 Signal 0V(L) CN100-10 GND LPC3 PCB Ground CN704-10 CN100-11 nFEED LPC3 PCB Feed Signal +5V(H) CN704-11 0V(L) CN100-12 GND LPC3 PCB...
Page 114
DP-1510P/1810P /1810F/2010E SC PCB Signal Name Destination Signal Waveform Function Pin No. CN101-4 MGND LVPS PCB Ground CN61-4 CN101-5 MGND LVPS PCB Ground CN61-5 CN101-6 MGND LVPS PCB Ground CN61-6 CN101-7 LVPS PCB +5 VDC Power Supply CN61-7 CN101-8 LVPS PCB...
Page 115
DP-1510P/1810P /1810F/2010E SC PCB Signal Name Destination Signal Waveform Function Pin No. CN101-16 nLPOW1 LVPS PCB Energy Saver Mode Control +5V (H) CN61-16 Signal (Low Power 0V (L) Mode) CN104 SC PCB Signal Name Destination Signal Waveform Function Pin No.
Page 116
DP-1510P/1810P /1810F/2010E SC PCB Signal Name Destination Signal Waveform Function Pin No. CN104-11 A9 Flash Memory Address Signal +3.3V(H) Card 0V(L) CN104-12 A8 Flash Memory Address Signal +3.3V(H) Card 0V(L) CN104-13 A13 Flash Memory Address Signal +3.3V(H) Card 0V(L) CN104-14 A14...
Page 117
DP-1510P/1810P /1810F/2010E SC PCB Signal Name Destination Signal Waveform Function Pin No. CN104-22 A7 Flash Memory Address Signal +3.3V(H) Card 0V(L) CN104-23 A6 Flash Memory Address Signal +3.3V(H) Card 0V(L) CN104-24 A5 Flash Memory Address Signal +3.3V(H) Card 0V(L) CN104-25 A4...
Page 118
DP-1510P/1810P /1810F/2010E SC PCB Signal Name Destination Signal Waveform Function Pin No. CN104-33 nWEH Flash Memory High Enable +3.3V(H) Card H: Disable L: Enable 0V(L) CN104-34 GND Flash Memory Ground Card CN104-35 GND Flash Memory Ground Card CN104-36 nCD Flash Memory...
Page 119
DP-1510P/1810P /1810F/2010E SC PCB Signal Name Destination Signal Waveform Function Pin No. CN104-44 RSV Flash Memory Not Used Card CN104-45 RSV Flash Memory Not Used Card CN104-46 A17 Flash Memory Address Signal +3.3V(H) Card 0V(L) CN104-47 A18 Flash Memory Address Signal +3.3V(H)
Page 120
DP-1510P/1810P /1810F/2010E SC PCB Signal Name Destination Signal Waveform Function Pin No. CN104-56 N.C. Flash Memory Not Used Card CN104-57 RSV Flash Memory Not Used Card CN104-58 nRST Flash Memory Reset Signal +5V(H) Card H: Not Reset L: Reset 0V(L)
Page 121
DP-1510P/1810P /1810F/2010E SC PCB Signal Name Destination Signal Waveform Function Pin No. CN104-67 nID0 Flash Memory Flash Card ID +5V(H) Card 0V(L) CN104-68 GND Flash Memory Ground Card CN106 SC PCB Signal Name Destination Signal Waveform Function Pin No. CN106-1...
Page 122
DP-1510P/1810P /1810F/2010E CN108 SC PCB Signal Name Destination Signal Waveform Function Pin No. CN108-1 +24V PNL6-1 PCB +24 VDC Power Supply +24V CN201-1 CN108-2 +5VP PNL6-1 PCB +5 VDC Pilot Power Supply, CN201-2 that provides power to the active components during the Sleep Mode.
Page 123
CN810-2 CN110-3 +VDO Video Signal 0.5V CN810-3 (LVPS + Output) CN110-4 -VDO Video Signal 0.5V CN810-4 (LVPS - Output) CN111 (Except DP-1510P/1810P) SC PCB Signal Name Destination Signal Waveform Function Pin No. CN111-1 N.C. Not Used CN111-2 +5VP MJR PCB...
Page 124
DP-1510P/1810P /1810F/2010E SC PCB Signal Name Destination Signal Waveform Function Pin No. CN111-3 MJR PCB Ground CN25-2 CN111-4 +24V MJR PCB +24 VDC Power Supply +24V CN25-3 CN111-5 pCMLD MJR PCB Line Switching Relay Drive +5V(H) CN25-4 Signal 0V(L) CN111-6 -8 N.C.
Page 125
DP-1510P/1810P /1810F/2010E SC PCB Signal Name Destination Signal Waveform Function Pin No. CN113-3 BMD[1] SDRM Data Signal +3.3V(H) 0V(L) CN113-4 BMD[2] SDRM Data Signal +3.3V(H) 0V(L) CN113-5 BMD[3] SDRM Data Signal +3.3V(H) 0V(L) CN113-6 BMD[4] SDRM Data Signal +3.3V(H) 0V(L)
Page 126
DP-1510P/1810P /1810F/2010E SC PCB Signal Name Destination Signal Waveform Function Pin No. CN113-14 BMA[2] SDRM Address Signal +3.3V(H) 0V(L) CN113-15 BMA[3] SDRM Address Signal +3.3V(H) 0V(L) CN113-16 BMA[4] SDRM Address Signal +3.3V(H) 0V(L) CN113-17 BMA[5] SDRM Address Signal +3.3V(H) 0V(L)
Page 127
DP-1510P/1810P /1810F/2010E SC PCB Signal Name Destination Signal Waveform Function Pin No. CN113-25 BMD[12] SDRM Data Signal +3.3V(H) 0V(L) CN113-26 BMD[13] SDRM Data Signal +3.3V(H) 0V(L) CN113-27 BMD[14] SDRM Data Signal +3.3V(H) 0V(L) CN113-28 BMA[7] SDRM Address Signal +3.3V(H) 0V(L)
Page 128
DP-1510P/1810P /1810F/2010E SC PCB Signal Name Destination Signal Waveform Function Pin No. CN113-36 nBDQML SDRM Input/Output Mask Signal +3.3V(H) 0V(L) CN113-37 BMD[37] SDRM Data Signal +3.3V(H) 0V(L) CN113-38 BMD[38] SDRM Data Signal +3.3V(H) 0V(L) CN113-39 GND SDRM Ground CN113-40 N.C.
Page 129
DP-1510P/1810P /1810F/2010E SC PCB Signal Name Destination Signal Waveform Function Pin No. CN113-48 nBCAS S-DRAM Column Address SDRM +3.3V(H) Strobe Command 0V(L) CN113-49 BMD[18] Data Signal SDRM +3.3V(H) 0V(L) CN113-50 BMD[19] Data Signal SDRM +3.3V(H) 0V(L) CN113-51 BMD[20] Data Signal SDRM +3.3V(H)
Page 130
DP-1510P/1810P /1810F/2010E SC PCB Signal Name Destination Signal Waveform Function Pin No. CN113-59 BMD[27] Data Signal SDRM +3.3V(H) 0V(L) CN113-60 BMD[28] Data Signal SDRM +3.3V(H) 0V(L) CN113-61 +3.3V +3.3 VDC Power Supply SDRM +3.3V CN113-62 BMD[29] Data Signal SDRM +3.3V(H)
Page 131
16MB 128MB 0V(L) CN113-70 SMEMID[2] SDRM +3.3V(H) 0V(L) CN113-71 SMEMID[3] SDRM +3.3V(H) 0V(L) CN113-72 GND Ground SDRM CN114 (Except DP-1510P/1810P) SC PCB Signal Name Destination Signal Waveform Function Pin No. CN114-1 L2 (T) MJR PCB Line Signal CN22-1 CN114-2 N.C.
Page 132
DP-1510P/1810P /1810F/2010E SC PCB Signal Name Destination Signal Waveform Function Pin No. CN120-3 CCD PCB Ground CN51-6 CN120-4 CCD PCB Transfer Gate Clock +3.3V CN51-7 CN120-5 N.C. Not Used CN120-6 CCD PCB Reset Gate Clock +3.3V CN51-8 CN120-7 N.C. Not Used...
Page 133
DP-1510P/1810P /1810F/2010E SC PCB Signal Name Destination Signal Waveform Function Pin No. CN121-2 +5VI EP PCB +5 VDC Power Supply CN1-2 CN121-3 AL[1] EP PCB Address Signal +5V(H) CN1-3 0V(L) CN121-4 AL[2] EP PCB Address Signal +5V(H) CN1-4 0V(L) CN121-5...
Page 134
DP-1510P/1810P /1810F/2010E SC PCB Signal Name Destination Signal Waveform Function Pin No. CN121-13 nIOWRH EP PCB I/O Write (High) Signal +5V(H) CN1-13 H: Write Disable L: Write Enable 0V(L) CN121-14 GND EP PCB Ground CN1-14 CN121-15 N.C. EP PCB Not Used CN1-15 CN121-16 N.C.
Page 135
DP-1510P/1810P /1810F/2010E SC PCB Signal Name Destination Signal Waveform Function Pin No. CN121-24 IOD[9] EP PCB Data Signal +5V(H) CN1-24 CN121-25 IOD[12] EP PCB Data Signal +5V(H) CN1-25 CN121-26 IOD[13] EP PCB Data Signal +5V(H) CN1-26 CN121-27 N.C. EP PCB...
Page 136
DP-1510P/1810P /1810F/2010E SC PCB Signal Name Destination Signal Waveform Function Pin No. CN121-36 nPDLOPT EP PCB Option Detection Signal +5V(H) CN1-36 H: Option Not Installed L: Option Installed 0V(L) CN121-37 pPDLREQ EP PCB Direct Memory Access Data +5V(H) CN1-37 Request Signal...
Page 137
DP-1510P/1810P /1810F/2010E SC PCB Signal Name Destination Signal Waveform Function Pin No. CN121-47 PD[12] EP PCB Data Signal +5V(H) CN1-47 CN121-48 PD[13] EP PCB Data Signal +5V(H) CN1-48 CN121-49 GND EP PCB Ground CN1-49 CN121-50 GND EP PCB Ground CN1-50...
Page 138
DP-1510P/1810P /1810F/2010E SC PCB Signal Name Destination Signal Waveform Function Pin No. CN121-58 AL[12] EP PCB Address Signal +5V(H) CN1-58 0V(L) CN121-59 N.C. EP PCB Not Used CN1-59 CN121-60 N.C. EP PCB Not Used CN1-60 CN121-61 nIORD EP PCB I/O Read Signal...
Page 139
DP-1510P/1810P /1810F/2010E SC PCB Signal Name Destination Signal Waveform Function Pin No. CN121-69 IOD[6] EP PCB Data Signal +5V(H) CN1-69 CN121-70 IOD[7] EP PCB Data Signal +5V(H) CN1-70 CN121-71 IOD[10] EP PCB Data Signal +5V(H) CN1-71 CN121-72 IOD[11] EP PCB...
Page 140
DP-1510P/1810P /1810F/2010E SC PCB Signal Name Destination Signal Waveform Function Pin No. CN121-80 N.C. EP PCB Not Used CN1-80 CN121-81 nOPON EP PCB Option Detection Signal +5V(H) CN1-81 H: Option Not Installed L: Option Installed 0V(L) CN121-82 N.C. EP PCB...
Page 141
DP-1510P/1810P /1810F/2010E SC PCB Signal Name Destination Signal Waveform Function Pin No. CN121-92 PD[7] EP PCB Data Signal +5V(H) CN1-92 CN121-93 GND EP PCB Ground CN1-93 CN121-94 GND EP PCB Ground CN1-94 CN121-95 PD[10] EP PCB Data Signal +5V(H) CN1-95...
Page 142
DP-1510P/1810P /1810F/2010E SC PCB Signal Name Destination Signal Waveform Function Pin No. CN123-2 +5VI G3B PCB +5 VDC Power Supply CN131-2 LANB PCB CN2-2 CN123-3 AL[1] G3B PCB Address Signal CN131-3 LANB PCB CN2-3 CN123-4 AL[2] G3B PCB Address Signal...
Page 143
DP-1510P/1810P /1810F/2010E SC PCB Signal Name Destination Signal Waveform Function Pin No. CN123-12 nCS0E G3B PCB Chip Enable Signal +5V(H) CN131-12 H: Disable L: Enable 0V(L) LANB PCB CN2-12 CN123-13 nIOWRH G3B PCB I/O Write (High) Signal +5V(H) CN131-13 H: Write Disable...
Page 144
DP-1510P/1810P /1810F/2010E SC PCB Signal Name Destination Signal Waveform Function Pin No. CN123-22 IOD[5] G3B PCB Data Signal +5V(H) CN131-22 LANB PCB 0V(L) CN2-22 CN123-23 IOD[8] G3B PCB Data Signal +5V(H) CN131-23 LANB PCB 0V(L) CN2-23 CN123-24 IOD[9] G3B PCB...
Page 145
DP-1510P/1810P /1810F/2010E SC PCB Signal Name Destination Signal Waveform Function Pin No. CN123-32 N.C. G3B PCB Not Used CN131-32 LANB PCB CN2-32 CN123-33 +5VP G3B PCB +5 VDC Pilot Power Supply, CN131-33 that provides power to the active components during LANB PCB the Sleep Mode.
Page 146
DP-1510P/1810P /1810F/2010E SC PCB Signal Name Destination Signal Waveform Function Pin No. CN123-42 AL[12] G3B PCB Address Signal CN131-42 LANB PCB CN2-42 CN123-43 nCS09 G3B PCB Chip Enable Signal +5V(H) CN131-43 H: Disable L: Enable 0V(L) LANB PCB CN2-43 CN123-44 nCS0A...
Page 147
DP-1510P/1810P /1810F/2010E SC PCB Signal Name Destination Signal Waveform Function Pin No. CN123-52 IOD[3] G3B PCB Data Signal +5V(H) CN131-52 LANB PCB 0V(L) CN2-52 CN123-53 IOD[6] G3B PCB Data Signal +5V(H) CN131-53 LANB PCB 0V(L) CN2-53 CN123-54 IOD[7] G3B PCB...
Page 148
DP-1510P/1810P /1810F/2010E SC PCB Signal Name Destination Signal Waveform Function Pin No. CN123-62 N.C. G3B PCB Not Used CN131-62 LANB PCB CN2-62 CN123-63 nPSDES G3B PCB Energy Saver Mode Disable +5V(H) CN131-63 Signal 0V(L) LANB PCB CN2-63 CN123-64 N.C. G3B PCB...
Page 149
DP-1510P/1810P /1810F/2010E SC PCB Signal Name Destination Signal Waveform Function Pin No. CN220-4 DATA2 Centronics Data Signal +5V(H) 0V(L) CN220-5 DATA3 Centronics Data Signal +5V(H) 0V(L) CN220-6 DATA4 Centronics Data Signal +5V(H) 0V(L) CN220-7 DATA5 Centronics Data Signal +5V(H) 0V(L)
Page 150
DP-1510P/1810P /1810F/2010E SC PCB Signal Name Destination Signal Waveform Function Pin No. CN220-15 Not Used Centronics Not Used CN220-16 GND Centronics Ground CN220-17 FG Centronics Ground CN220-18 PLH Centronics +5V Pull Up CN220-19 GND Centronics Ground CN220-20 GND Centronics Ground...
Page 151
DP-1510P/1810P /1810F/2010E SC PCB Signal Name Destination Signal Waveform Function Pin No. CN220-27 GND Centronics Ground CN220-28 GND Centronics Ground CN220-29 GND Centronics Ground CN220-30 GND Centronics Ground Reverse Request / Initialize CN220-31 nINIT Centronics +5V(H) (Host→Peripheral) 0V(L) Data Available / Error...
DP-1510P/1810P /1810F/2010E 3.7. PNL6-1 PC Board PNL6-1 Signal Name Destination Signal Waveform Function PCB Pin CN1-1 SCN[2] PNL2 PCB Key Scan Signal CN20-1 CN1-2 SCN[1] PNL2 PCB Key Scan Signal CN20-2 CN1-3 SCN[3] PNL2 PCB Key Scan Signal CN20-3 CN1-4...
Page 153
DP-1510P/1810P /1810F/2010E PNL6-1 Signal Name Destination Signal Waveform Function PCB Pin CN1-11 KIN[4] PNL2 PCB Key Scan Signal CN20-11 CN1-12 pLED[1] PNL2 PCB LED Data CN20-12 H: ON CN1-13 KIN[3] PNL2 PCB Key Scan Signal CN20-13 CN1-14 pLED[0] PNL2 PCB...
Page 154
DP-1510P/1810P /1810F/2010E PNL6-1 Signal Name Destination Signal Waveform Function PCB Pin CN1-22 SWCT1 PNL2 PCB One Touch Choice CN20-22 H: ON CN1-23 KIN[2] PNL2 PCB Key Scan Signal CN20-23 CN1-24 BLCNT2 PNL2 PCB LED Control CN20-24 H: ON CN1-25 SCN[5]...
Page 155
DP-1510P/1810P /1810F/2010E CN202 PNL6-1 Signal Name Destination Signal Waveform Function PCB Pin CN202-1 BAT/BUZCLK PNL6-2 PCB Battery Voltage +3~0V CN210-1 Buzzer Clock +24V BUZCLK CN202-2 PNL6-2 PCB Ground CN210-2 CN202-3 SCN[6] PNL6-2 PCB Key Scan Signal CN210-3 CN202-4 SCN[7] PNL6-2 PCB...
Page 156
DP-1510P/1810P /1810F/2010E PNL6-1 Signal Name Destination Signal Waveform Function PCB Pin CN203-6 nLEDCT[0] PNL6-2 PCB LED Control CN211-6 CN203-7 nLEDCT[1] PNL6-2 PCB LED Control CN211-7 CN203-8 nLEDCT[2] PNL6-2 PCB LED Control CN211-8 CN203-9 nLEDCT[3] PNL6-2 PCB LED Control CN211-9 CN203-10 nLEDCT[4]...
DP-1510P/1810P /1810F/2010E 3.10. LPC3 PC Board CN701 LPC3 PCB Signal Name Destination Signal Waveform Function Pin No. CN701-1 L+5V Laser Circuit +5 VDC Power CN811-1 Supply CN701-2-4 N.C. Not Used CN701-5 nS/H Sample Hold Signal CN811-3 CN701-6 nHSYNC Horizontal Synchronous...
Page 160
DP-1510P/1810P /1810F/2010E LPC3 PCB Signal Name Destination Signal Waveform Function Pin No. CN701-14 nPMON Polygon Motor Rotation +5V (H) CN3-3 Signal 0V (L) CN701-15 MGND Ground CN3-4 CN701-16 +24V +24 VDC Power Supply +24V CN3-5 CN702 LPC3 PCB Signal Name...
Page 161
DP-1510P/1810P /1810F/2010E CN703 LPC3 PCB Signal Name Destination Signal Waveform Function Pin No. CN703-1 +24V ILS PC Board +24 VDC Power Supply +24V (Interlock Switch) CN703-2 N.C. Not Used CN703-3 +24VD1 ILS PC Board +24 VDC Power Supply +24V (Interlock Switch) CN704 Refer to SC PC Board CN100.
Page 162
DP-1510P/1810P /1810F/2010E LPC3 PCB Signal Name Destination Signal Waveform Function Pin No. CN705-8 nRSEN Registration Registration Sensor Signal +5V (H) Sensor 0V (L) CN705-9 Registration Ground Sensor CN705-10 LDRSEN Registration Photo Sensor DC Drive Sensor Voltage +1.5V CN705-11 nPCHK1 Paper Sensor...
Page 163
DP-1510P/1810P /1810F/2010E CN706 LPC3 PCB Signal Name Destination Signal Waveform Function Pin No. CN706-1 +24VM Lift Motor +24 VDC Power Supply +24V CN706-2 nLIFT1 Lift Motor Lift DC Motor Ready Signal +24V CN707 LPC3 PCB Signal Name Destination Signal Waveform Function Pin No.
Page 164
DP-1510P/1810P /1810F/2010E CN708 LPC3 PCB Signal Name Destination Signal Waveform Function Pin No. CN708-1 THERM1 Thermistor-1 Thermistor Output Signal CN708-2 THERM2 Thermistor-2 Ground +0.6V CN708-3 nESEN Paper Exit Inner Under Tray Paper Exit Sensor-1 Signal CN708-4 Paper Exit Ground Sensor-2...
Page 165
DP-1510P/1810P /1810F/2010E LPC3 PCB Signal Name Destination Signal Waveform Function Pin No. CN710-3 +24V LVPS +24 VDC Power Supply +24V CN62-3 CN710-4 MGND LVPS Ground CN62-4 CN710-5 MGND LVPS Ground CN62-5 CN710-6 MGND LVPS Ground CN62-6 CN711 LPC3 PCB Signal Name...
Page 166
DP-1510P/1810P /1810F/2010E CN712 LPC3 PCB Signal Name Destination Signal Waveform Function Pin No. CN712-1 +24VM DC Motor-1 +24 VDC Power Supply +24V CN712-2 +24VM DC Motor-2 +24 VDC Power Supply +24V CN712-3 MGND DC Motor-3 Ground CN712-4 MGND DC Motor-4...
Page 167
DP-1510P/1810P /1810F/2010E LPC3 PCB Signal Name Destination Signal Waveform Function Pin No. CN713-2 +24VM Keep Solenoid +24 VDC Power Supply +24V CN713-3 nDUPSEN1 Keep Solenoid Duplex Sensor1 Signal +24V CN714 (DP-2010E only) LPC3 PCB Signal Name Destination Signal Waveform Function Pin No.
Page 168
DP-1510P/1810P /1810F/2010E LPC3 PCB Signal Name Destination Signal Waveform Function Pin No. CN715-4 +24VF4 HTC PCB +24 VDC Power Supply +24V CN765-4 CN715-5 HTC PCB Ground CN765-5 CN715-6 pZCIN HTC PCB Heater Control Signal CN765-6 CN715-7 N.C. Not Used CN716...
Page 169
DP-1510P/1810P /1810F/2010E LPC3 PCB Signal Name Destination Signal Waveform Function Pin No. CN722-3 nBPSEN Toner Waste Toner Waste Container Sensor Sensor CN740-3 H: Container Installed L: Container Not Installed CN722-4 nTFSEN Toner Waste Toner Waste Sensor Sensor H: Full CN740-4...
Page 170
DP-1510P/1810P /1810F/2010E CN726 LPC3 PCB Signal Name Destination Signal Waveform Function Pin No. CN726-1 pBTHP Toner Bottle HP Photo Sensor DC Drive Sensor-1 Voltage +1.5V CN726-2 Toner Bottle HP Ground Sensor-2 CN726-3 LDBTHP Toner Bottle HP Toner Bottle HP Sensor...
Page 171
DP-1510P/1810P /1810F/2010E LPC3 PCB Signal Name Destination Signal Waveform Function Pin No. CN731-11 pADF2A CST4 PCB 2nd Feed Roller Drive CN776-11 Signal CN731-12 pMRCLH2A CST4 PCB 2nd Medium Roller Drive CN776-12 Signal CN731-13 pLIFT2 CST4 PCB 2nd Lift DC Motor Drive...
Page 172
DP-1510P/1810P /1810F/2010E LPC3 PCB Signal Name Destination Signal Waveform Function Pin No. CN731-22 pLIFT3 CST4 PCB 3rd Lift DC Motor Drive CN776-22 Signal CN731-23 nPCHK3 CST4 PCB 3rd Paper Tray Paper CN776-23 Detection Signal L: Detect CN731-24 nCASET3 CST4 PCB...
Page 173
DP-1510P/1810P /1810F/2010E LPC3 PCB Signal Name Destination Signal Waveform Function Pin No. CN731-33 nCASET4 CST4 PCB 4th Paper Tray Detection CN776-33 Signal CN731-34 pUPLIMIT4 CST4 PCB 4th Lift DC Motor Ready CN776-34 Signal CN731-35 nFDPCHK4 CST4 PCB 4th Paper Tray Paper...
DP-1510P/1810P /1810F/2010E 3.11. ADF PC Board CN21 Refer to SC PC Board CN3. CN22 ADF PCB Signal Name Destination Signal Waveform Function Pin No. CN22-1 OUTA ADF Motor-1 Motor Control Signal +24V CN22-2 +24V ADF Motor-2 +24 VDC Power Supply...
Page 175
DP-1510P/1810P /1810F/2010E CN25 ADF PCB Signal Name Destination Signal Waveform Function Pin No. CN25-1 +24VOPF Stamp Solenoid +24 VDC Power Supply +24V CN25-2 nASTAMP Stamp Solenoid Stamp Control Signal +24V CN27 ADF PCB Signal Name Destination Signal Waveform Function Pin No.
Page 176
DP-1510P/1810P /1810F/2010E ADF PCB Signal Name Destination Signal Waveform Function Pin No. CN28-6 Original Length +5 VDC Power Supply Sensor2 CN28-7 nAB4S SNS PCB Original Width Detection +5V(H) CN41-1 Signal L: Detect CN28-8 nAA3S SNS PCB Original Width Detection CN41-2...
Page 177
DP-1510P/1810P /1810F/2010E CN30 ADF PCB Signal Name Destination Signal Waveform Function Pin No. CN30-1 N.C. Not Used CN30-2 N.C. Not Used CN30-3 N.C. Not Used CN30-4 nAB2SN Duplex Duplex Eject Detection Eject Sensor Signal L: Detect CN30-5 Duplex Ground Eject Sensor...
DP-1510P/1810P /1810F/2010E 3.12. CCD PC Board CN51 Refer to SC PC Board CN106 and CN120. CN52 CCD PCB Signal Name Destination Signal Waveform Function Pin No. CN52-1 FGND Ground Edition 2.0 APR 2002...
DP-1510P/1810P /1810F/2010E 3.14. HTC PC Board CN760 HTC PCB Signal Name Destination Signal Waveform Function Pin No. CN760 AC(L) INLET-1 AC Power Supply AC120V 230V CN761 HTC PCB Signal Name Destination Signal Waveform Function Pin No. CN761 AC(N) INLET-3 AC Power Supply...
Page 181
DP-1510P/1810P /1810F/2010E CN767 HTC PCB Signal Name Destination Signal Waveform Function Pin No. CN767-1 AC(N) CN48W03 AC Power Supply AC120V 230V CN767-2 AC(N) CN48W03 AC Power Supply AC120V 230V Edition 2.0 APR 2002...
DP-1510P/1810P /1810F/2010E 3.15. HVPS CN800 Refer to LPC3 PC Board CN702. HVPS Signal Name Destination Signal Waveform Function Pin No. HVPS T1 Transfer Roller Transfer Signal (High Voltage) HVPS C CHARGE Charge Roller Charge Signal (High Voltage) HVPS D DEVELOPM...
DP-1510P/1810P /1810F/2010E 3.16. LVPS CN60 Refer to HTC PC Board CN762. CN61 Refer to SC PC Board CN101. CN62 Refer to LPC3 PC Board CN710 and CN716. Edition 2.0 APR 2002...
DP-1510P/1810P /1810F/2010E 3.21. MJR PC Board CN20 MJR PCB Signal Name Destination Signal Waveform Function Pin No. CN20-1 Telephone Line Line Signal CN20-2 N.C. Not Used CN20-3 Telephone Line Line Signal CN20-4 Telephone Line Line Signal CN20-5 N.C. Not Used...
DP-1510P/1810P /1810F/2010E 3.22. CST4 PC Board CN771 CST4 PCB Signal Name Destination Signal Waveform Function Pin No. CN771-1 nPCHK2 Paper Detect 2nd Paper Tray Paper Sensor-1 Detection Signal L: Detect CN771-2 Paper Detect Ground Sensor-2 CN771-3 LDSP2 Paper Detect Photo Sensor DC Drive...
Page 190
DP-1510P/1810P /1810F/2010E CN772 CST4 PCB Signal Name Destination Signal Waveform Function Pin No. CN772-1 +24VM Feed Clutch-1 +24 VDC Power Supply +24V CN772-2 nADF2 Feed Clutch-4 2nd Paper Tray Feed Roller +24V Drive Signal CN772-3 +24VM Medium Roller +24 VDC Power Supply...
Page 191
DP-1510P/1810P /1810F/2010E CN774 CST4 PCB Signal Name Destination Signal Waveform Function Pin No. CN774-1 n3MRDY DC Motor DC Motor Ready Signal CN774-2 n3MON DC Motor DC Motor Ready Signal CN774-3 +24VM DC Motor +24 VDC Power Supply +24V CN774-4 MGND...
DP-1510P/1810P /1810F/2010E 3.23. LANB PC Board Refer to SC PC Board CN123. LANB PCB Signal Name Destination Signal Waveform Function Pin No. CN5-1 LINK LANC PCB LANB PCB/ LANC PCB Link CN200-1 Signal CN5-2 LANC PCB +5 VDC Power Supply...
DP-1510P/1810P /1810F/2010E 4 Troubleshooting 4.1. Initial Troubleshooting Flowchart START Plug the Power Cord in and turn the Power Switch ON. Does the unit power up normally? Does the LCD display the function correctly? Troubleshoot Improper LCD Display (Sect. 4.2). Troubleshoot any 3-digit INFO.
DP-1510P/1810P /1810F/2010E 4.2. Improper LCD Display START Check connectors: CN108 (SC PCB) and CN201 (PNL6-1 PCB). Is LED/LCD displayed? Does the display appear normal? Does CN108, pin 3 on the SC PCB measure +5 VDC? Replace the LCD Replace the SC PCB.
DP-1510P/1810P /1810F/2010E 4.3. Printed Copy Quality Problems 4.3.1. Black Copy START Is the Test Pattern printout in Copier F1 Mode or Fax (DP-1810F) Service Mode 3 normal? Check the Scanner mechanism. Is the Process Unit operational? Replace the Process Unit.
Page 199
DP-1510P/1810P /1810F/2010E 4.3.2. Blank Copy START Is the Test Pattern printout in Copier F1 Mode or Fax (DP-1810F) Service Mode 3 normal? Check the Scanner mechanism. Is the Process Unit operational? Replace the Process Unit. Are there any foreign particles or stains on the BTR? 1.
Page 200
DP-1510P/1810P /1810F/2010E 4.3.3. Vertical White Lines START Is the Test Pattern printout in Copier F1 Mode or Fax (DP-1810F) Service Mode 3 normal? Check the Scanner mechanism. Is the recording paper damp? Replace the recording paper. Is the Process Unit operational? Replace the Process Unit.
Page 201
DP-1510P/1810P /1810F/2010E 4.3.4. Ghost Images A A A START Is the Test Pattern printout in Copier F1 Mode or Fax (DP-1810F) Service Mode 3 normal? Check the Scanner mechanism. Is the recording paper damp? Replace the recording paper. Is the Process Unit operational? Replace the Process Unit.
Page 202
DP-1510P/1810P /1810F/2010E 4.3.5. Vertical Dark Lines START Is the Test Pattern printout in Copier F1 Mode or Fax (DP-1810F) Service Mode 3 normal? Check the Scanner mechanism. Is the Process Unit operational? Replace the Toner Bottle. Are there any foreign particles or stains on the BTR? 1.
Page 203
DP-1510P/1810P /1810F/2010E 4.3.6. Horizontal Dark Lines START Is the Test Pattern printout in Copier F1 Mode or Fax (DP-1810F) Service Mode 3 normal? Check the Scanner mechanism. Is the Toner Cartridge operational? Replace the Toner Cartridge. Are there any foreign particles or stains on the BTR? 1.
Page 204
DP-1510P/1810P /1810F/2010E 4.3.7. Dark Background START Is the Test Pattern printout in Copier F1 Mode or Fax (DP-1810F) Service Mode 3 normal? Check the Scanner mechanism. Is the recording paper damp? Replace the recording paper. Is the Process Unit operational? Replace the Process Unit.
Page 205
DP-1510P/1810P /1810F/2010E 4.3.8. Light Print START Is the Test Pattern printout in Copier F1 Mode or Fax (DP-1810F) Service Mode 3 normal? Check the Scanner mechanism. Is the recording paper damp? Replace the paper. Is the Process Unit operational? Replace the Process Unit.
Page 206
DP-1510P/1810P /1810F/2010E 4.3.9. Horizontal White Lines START Is the Test Pattern printout in Copier F1 Mode or Fax (DP-1810F) Service Mode 3 normal? Check the Scanner mechanism. Is the recording paper damp? Replace the recording paper. Is the Process Unit operational? Replace the Process Unit.
Page 207
DP-1510P/1810P /1810F/2010E 4.3.10. Improper Fusing (Printed image does not bond to the paper) START Is the recording paper damp? Replace the recording paper. Is the Fuser Unit normal? Replace the Fuser Unit. (See Note) Note: Replace the entire Fuser Unit when the Thermostat, the Thermal Fuse or the Thermistor Assembly becomes an open-circuit.
Page 208
DP-1510P/1810P /1810F/2010E 4.3.11. Voids in Solid Areas START Is the recording paper damp? Replace the recording paper. Is the the Process Unit operational? Replace the Process Unit. Are there any foreign particles or stains on the BTR? 1. Clean the BTR with a soft, dry cloth.
Page 209
DP-1510P/1810P /1810F/2010E 4.3.12. Black Dots START Is the Process Unit operational? Replace the Process Unit. Are the Fuser and Pressure Roller surfaces clean? Clean or replace the rollers. Edition 2.0 APR 2002...
Page 210
DP-1510P/1810P /1810F/2010E 4.3.13. Recording Paper Creases START Is the recording paper damp? Replace the recording paper. Are there any foreign particles or stains in the paper path? Remove any obstructions and / or clean the paper path. Is the recording paper skewing?
Page 211
DP-1510P/1810P /1810F/2010E 4.3.14. Poor Printed Copy Quality START Is the Test Pattern printout in Copier F1 Mode normal? 1. Replace the LPC3 PCB. 2. Replace the LSU. 3. Replace the HVPS. 4. Replace the Process Unit. Make a local copy.
Page 212
Is the recording paper size and thickness within specification? Replace with correct paper. Is the Panasonic Toner Bottle being used? Replace with the Panasonic Toner Bottle. Are all switches and sensors operating properly? Adjust, clean or replace. Are there any foreign particles...
Page 213
DP-1510P/1810P /1810F/2010E 4.3.17. Scanned Copy Quality Problems START Is the Scanner Lamp abnormal? Replace the Scanner Lamp. Are there any foreign particles or paper pieces in the scanning area? Remove the foreign particles or paper pieces from the scanning area.
Page 214
DP-1510P/1810P /1810F/2010E 4.3.18. Print Skew Adjustment for Platen Glass Scanning Follow the procedures below to adjust for the skewing when scanning original(s) from the Platen Glass. (1) Make sure that the Scanner Unit is in the Standby Mode. (2) 3 Screws and remove the Left Platen Cover.
DP-1510P/1810P /1810F/2010E 4.4. Document Feeder (ADF) 4.4.1. No Document Feed START Set the Document Is the Document set properly. properly? Is the Document Set the Document on thickness or size the Platen Glass. within specifications? Does the NP Sensor Does the LCD activate...
Page 216
DP-1510P/1810P /1810F/2010E 4.4.2. Document Jam START Remove any obstacles Are there any obstacles in blocking the path. the document path? Check the ADF Motor Does the Paper Feed connector. Roller rotate? Is the trouble resolved? Replace the ADF Motor or the ADF PCB.
Page 217
DP-1510P/1810P /1810F/2010E 4.4.3. Document Skew START Are there any obstacles Remove any obstacles in the document path? from the document path. Are the Pre Feed and Paper Replace the Pre Feed Feed Rollers operational? and / or Paper Feed Roller.
Page 218
DP-1510P/1810P /1810F/2010E 4.4.3.1. ADF Feed Skew Adjustment Using a lined Original (about 20 lb (75 g/m ) weight pager), make a copy from the ADF to check for feeding alignment. (1) Copy an Original using the ADF. (2) Open the ADF Cover and release the Stopper.
DP-1510P/1810P /1810F/2010E 4.5. Troubleshooting the LAN Interface 4.5.1. Checking Network Configuration START Print the current Internet Parameters List Ask the customer for the Pre-Installation Information form filled out by the Network Administrator. Verify this information with the Internet Parameters List that you just printed.
Page 220
DP-1510P/1810P /1810F/2010E 4.5.2. Testing the TCP/IP Network It is beyond the scope of this Service Manual to cover Networking in detail, there are many excellent manuals on this subject, but we hope the information in this section will aid with your troubleshooting efforts.
Page 221
DP-1510P/1810P /1810F/2010E 2. Checking Current Configuration Print the current unit Internet Parameters configuration. Locate a PC connected to the same Subnet Mask as the unit, then from the DOS Prompt, type the following command-line utility: "ipconfig /all" for Windows 98/Me/XP/2000/NT.
Page 222
DP-1510P/1810P /1810F/2010E PINGing the Unit C:\WINDOWS>ping ef1.labo.mgcs.com Pinging ef1.labo.mgcs.com [192.168.3.5] with 32 bytes of data: Reply from 192.168.3.5: bytes=32 time=5ms TTL=253 Reply from 192.168.3.5: bytes=32 time=4ms TTL=253 Reply from 192.168.3.5: bytes=32 time=4ms TTL=253 Reply from 192.168.3.5: bytes=32 time=4ms TTL=253 PINGing the Default Gateway (Default Router IP Address) C:\WINDOWS>ping 192.168.3.254...
Page 223
DP-1510P/1810P /1810F/2010E If the physical destination is far and it’s connected by WAN (Wide Area Network), the PING option command default value must be changed to compensate for the expected delayed response. e.g. -n 10 : The number of echo requests that the command should send.
Page 224
DP-1510P/1810P /1810F/2010E 5. Managing Network Route Tables In the simplest case a router connects two network segments. In this model, the system used to join the two segments needs to know only about these segments. The routing table for router R1 in this case is simple; the following table shows its key routes:...
Page 225
DP-1510P/1810P /1810F/2010E When the packet does not reach the specified destination even when the physical connection is properly made, check the registered persistent routes on the same subnet as the Unit by typing "route print" in the DOS command-line. The output display is shown below: C:\WINDOWS>route print...
Page 226
250 Sender OK rcpt to:fax@labo.mgcs.com 250 Receipient OK data 354 Email, end with "CRLF . CR LF" [Press the Enter Key] Panasonic Internet Fax test test [Press the Enter Key] [Press the Enter Key] [Press the Enter Key] 250 OK, Mail accept...
The self-diagnostic functions detect troubles in the important components of the copier. When any trouble occurs, the copier stops. Note: Some Codes may not be used for DP-1510P/1810P, which are reserved for future use. 4.6.1. User Error Codes (U Code) Note: Uxx and a message will appear on the Panel Display.
Page 228
DP-1510P/1810P /1810F/2010E User Error Codes (U Code) Table Code Item Check Points CLOSE ADF COVER 1. ADF Cover is open. 2. ADF is not installed correctly. 3. ADF Cover Sensor is disconnected. 4. ADF Cover Sensor is defective. 5. LVPS connector is disconnected.
Page 229
DP-1510P/1810P /1810F/2010E 4.6.2. Jam Error Codes (J Code) Section Jam Location Paper Transport / Exit Area Paper Entry Area Jam Error Codes (J Codes) Table Code Contents Section The Registration Sensor did not detect paper within a predetermined time after paper started feeding.
Page 230
DP-1510P/1810P /1810F/2010E Jam Error Codes (J Codes) Table Code Contents Section The eject paper Sensor does not detect paper within a predetermined time after Registration Sensor is ON. The eject paper Sensor does not detect no paper within a predetermined time after eject paper Sensor is ON.
Page 231
DP-1510P/1810P /1810F/2010E 4.6.3. Mechanical Error Codes (E Code) E1: Optical Unit Error Code Function Check Points E1- 20 Laser Unit Horizontal 1. LPC3 PCB connector(s) is disconnected. Synchronization 2. LPC3 PCB is defective. 3. LSU is defective. 4. LVPS connector is disconnected.
Page 232
DP-1510P/1810P /1810F/2010E E4: Fuser Unit Error Code Function Check Points E4- 01 Fuser Warm-up Temperature 1. Fuser Thermistor is dirty. 2. Thermistor position is incorrect. 3. Fuser temperature is low. (Adjust F6-31) 4. Thermistor is defective. 5. Fuser Lamp connector is disconnected.
DP-1510P/1810P /1810F/2010E 4.7. Information Codes Table (For Facsimile) Fax Information Codes Code Mode Phase Description of Problem Cause C, D The length of the received document is over 2 m. Read Point Sensor does not go to Document is not set properly.
Page 234
DP-1510P/1810P /1810F/2010E Fax Information Codes Code Mode Phase Description of Problem Cause DCN was returned from receiver Receiver working in non-CCITT mode while transmitter is waiting for only. (Possible incompatibility) NSF/DIS. Transmitter had no polling "POLLED=ON" (polling XMT ready) is (Polling) function.
Page 235
DP-1510P/1810P /1810F/2010E Fax Information Codes Code Mode Phase Description of Problem Cause Remote side attempted to receive Inform the remote side that your (Polling) message from your machine in machine does not have the polling polling communication. transmission feature. Receiver did not detect post Transmitter is defective.
Page 236
DP-1510P/1810P /1810F/2010E Fax Information Codes Code Mode Phase Description of Problem Cause During reception, CD turned OFF Line is disconnected. or continued ON for long time. Transmitter is defective. During communication, lost loop - SC PCB or MJR PCB is defective.
Page 237
DP-1510P/1810P /1810F/2010E Fax Information Codes Code Mode Phase Description of Problem Cause 630 XMT or RCV Redial count over. No dial tone detected. Sensor dial tone (Polling) is not detected. (country dependent) Busy tone is detected. (country dependent) T1 timer (35±5 sec) elapsed without a signal from the receiver.
Page 238
DP-1510P/1810P /1810F/2010E Fax Information Codes Code Mode Phase Description of Problem Cause DNS Server connection timed out. Incorrect DNS Server address is set. DNS Server is down. Received an error response from Incorrect POP Server address is set. the DNS Server.
DATE TIME DIAGNOSTIC 00:00'42 123 456 789 01:55 C8649003C0000 1st digit 13th digit - PANASONIC DP-1810F ****************************** - PANASONIC DP-1810F- ***** -12345678901234567890- ******* 1st Digit: Manufacturer Code -: Not used/defined Fax Diagnostic Codes Definition Data Manufacturer Code Casio Canon Sanyo...
Page 240
DP-1510P/1810P /1810F/2010E 2nd Digit -: Not used/defined Fax Diagnostic Codes Definition Data ID (TSI, CSI, CIG) STOP Button Received Received Received Received Received Received Received Received Received Received Received Received Pressed Received Pressed Received Pressed Received Received Pressed Received Pressed...
Page 241
DP-1510P/1810P /1810F/2010E 4th Digit -: Not used/defined Fax Diagnostic Codes Definition Data Scanning Rate Resolution 20 ms/line 5 ms/line 10 ms/line 40 ms/line 0 ms/line 20 ms/line Fine 5 ms/line Fine 10 ms/line Fine Fine 40 ms/line Fine Fine Fine...
Page 243
DP-1510P/1810P /1810F/2010E 8th Digit -: Not used/defined Fax Diagnostic Codes Definition Data Advanced Cover Sheet Comm. Report XMT Check & Call Memory Transfer Report XMT Check & Call Memory Transfer 9th Digit -: Not used/defined Fax Diagnostic Codes Definition Data...
Page 244
DP-1510P/1810P /1810F/2010E 10th Digit -: Not used/defined Fax Diagnostic Codes Definition Data Coding JBIG JBIG 11th Digit -: Not used/defined Fax Diagnostic Codes Definition Data Symbol Rate V.34 (V.34) 2400 sr 2800 sr 3000 sr 3200 sr 3429 sr Edition 2.0...
This section explains how to solve problems including error messages or unexpected printing results. If the Panasonic Printing System (PCL) is not printing or working as expected, and if you are not sure what to do, start your troubleshooting by checking the basics below: •...
Page 247
Error Message appears on the PC Error Message Solutions Network Print DLL Error. • Check if the Panasonic Device is turned "On" and the 10Base-T/ 100Base-TX cable properly connected. • Printer Properties may be incorrectly configured. (i.e. Printer Port) Network Port is Busy.
DP-1510P/1810P /1810F/2010E 5 Service Modes 5.1. Service Modes (For Copier) These service modes are provided to assist the technician in checking for abnormalities in the copier and a means of making adjustments to the Input/Output of major components. 5.1.1. Service Mode Procedure 1.
Page 249
DP-1510P/1810P /1810F/2010E Service Modes Service Item Function Mode Electronic 00 Not Used Counter 01 Key Operator ID Key Operator’s identification code for access to the counter mode. Maintenance 02 Total Count Total count for all copies / prints. Count 03 PM Count Preventive Maintenance count.
Page 250
DP-1510P/1810P /1810F/2010E Service Modes Service Item Function Mode Service Adjustment Perform pseudo-operation of an item (selected by code numbers). 00 CHK Mirror Movement When replacing the exposure lamp. Procedure: a) Press the Start key to move the exposure lamp to the position (approx.
Page 251
DP-1510P/1810P /1810F/2010E Service Modes Service Item Function Mode Unit 00 Fax Function Parameters Maintenance 01 Service Alert Tel # Displays the contact number when a machine malfunction occurs. 02 Firmware 00 Host Displays the firmware version for host. Version 02 Scanner Displays the firmware version for scanner.
Page 252
DP-1510P/1810P /1810F/2010E F5 / F6 Information List (Sample) P.01 DP-1810P AAV109xxPU F 5 / F 6 I N F O R M A T I O N L I S T F5-00 COUNTRY VERSION USA/CAN F5-50 AUTO EXPOSURE (T/P) F5-01 ..
Page 253
DP-1510P/1810P /1810F/2010E Machine Setup Information List (Sample) DP-1810P AAV109xxPU - M A C H I N E S E T U P I N F O R M A T I O N - 1.FIRMWARE VERSION MACHINE NAME : DP-1810P...
Page 254
DP-1510P/1810P /1810F/2010E F7 Total Counter List (Sample) P.01 DP-1810P AAV109xxPU T O T A L C O U N T E R L I S T F7-01 KEY OPERATOR ID F7-02 TOTAL COUNT F7-03 PM COUNT F7-04 SCANNER PM COUNT...
Page 255
DP-1510P/1810P /1810F/2010E 5.1.3. F4 Mode: Input/Output Check Set the machine to service mode and press "4" on the Keypad. ↓ Press the “START” key. ↓ Select the Check Input or Check Output on the Control Panel. ↓ Enter the number to activate the test then press “START” key.
Page 256
DP-1510P/1810P /1810F/2010E F4 Mode (Input Check) Message Display Function Condition Remark 7 6 5 4 3 2 1 0 008 JAM Access Cover Open Door is open. For DP-1810F/2010E Detection Sensor (3rd Tray) Paper Level Sensor Upper Limit is detected.
Page 257
DP-1510P/1810P /1810F/2010E F4 Mode (Input Check) Message Display Function Condition Remark 7 6 5 4 3 2 1 0 031 ADF Original Sensor Sensor is activated. ADF Original Width A4/Letter size is detected. Sensor (A4/Letter) ADF Original Width B4 size is detected.
Page 258
DP-1510P/1810P /1810F/2010E F4 Mode (Output Check) Item Function Remark 063 1st Tray Feed Roller Clutch Activate 1st Tray Paper Drive Clutch after pressing Start key. 064 1st Tray Lift DC Motor Activate 1st Tray Lift DC Motor after pressing Start key.
Page 259
DP-1510P/1810P /1810F/2010E 5.1.4. F5 Mode: Copier Function Parameters Set the machine to Service Mode and press "5" on the Keypad. ↓ Press the “START” key. ↓ Select the desired code number on the Control Panel. ↓ If you wish to select another code number, scroll the menu with the arrow keys (↑ ↓).
Page 261
DP-1510P/1810P /1810F/2010E F5 Mode Item Function Factory Setting Margin Value Default 0 : 5mm 1 : 10mm 2 : 15mm 3 : 20mm Edge Value Default 0 : 5mm 1 : 10mm 2 : 15mm 3 : 20mm Book Value Default...
Page 262
DP-1510P/1810P /1810F/2010E F5 Mode Item Function Factory Setting Automatic Exposure (Text) 0 : No 1 : Yes 2 : Fix Text Error Diffusion 0 : Off 1 : On (Execute error diffusion on Text mode.) A4/LTR Size Select 0 : No 1 : Yes (Set paper side to A4/LTR if original is less than A4/LTR.)
Page 263
DP-1510P/1810P /1810F/2010E F5 Mode Item Function Factory Setting 88-89 Not Used Beep Sound 0 : Off 1 : Soft 2 : Loud M1, Size Y Set the default size for Manual Skyshot Mode, M1 and M2. M1, Size X M2, Size Y...
Page 264
DP-1510P/1810P /1810F/2010E 5.1.5. F6 Mode: Adjustment and Programming Set the machine to Service Mode and press "6" on the Keypad. ↓ Press the "START" key. ↓ Select the desired code number on the Control Panel. ↓ If you wish to select another code number, scroll the menu with the arrow keys (↑ ↓).
Page 265
DP-1510P/1810P /1810F/2010E F6 Mode Item Function Setting Trail edge detection timing of the Adjustment of trail edge void. -9 - 0 original image (-) : Decrease. 0.5mm Trail edge detection timing of the Adjustment of trail edge void. -9 - +15 copy image (+) : Increase.
Page 266
DP-1510P/1810P /1810F/2010E F6 Mode Item Function Setting Photo Mode Image Density Image density adjustment for Photo mode. -99 - +99 (-) : Darker. (+) : Lighter. Not Used CCD Read Timing Adjustment of CCD read position. -44 - +44 (+) : More delay.
Page 267
DP-1510P/1810P /1810F/2010E 5.1.6. F7 Mode: Electronic Counter Set the machine to Service Mode and press "7" on the Keypad. ↓ Press the “START” key. ↓ Select the desired code number on the Control Panel. ↓ If you wish to select another code number, scroll the menu with the arrow keys (↑ ↓).
Page 268
DP-1510P/1810P /1810F/2010E F7 Mode Service Item Function Mode Electronic Copy Count 20 Copy Print Count Total count of copies printed. Counter 21 Copy Scan Count Total count of copies scanned. PC Count 22 PC Print Count Total count printed from PC.
Page 269
DP-1510P/1810P /1810F/2010E 5.1.7. F8 Mode: Copier Operation Adjustment Set the machine to Service Mode and press "8" on the Keypad. ↓ Press the “START” key. ↓ Select the desired code number on the Control Panel. ↓ If you wish to select another code number, scroll the menu with the arrow keys (↑ ↓).
Page 270
DP-1510P/1810P /1810F/2010E 5.1.8. F9 Mode: System Maintenance Set the machine to Service Mode and press "9" on the Keypad. ↓ Press the “START” key. ↓ Select the desired code number on the Control Panel. ↓ If you wish to select another code number, scroll the menu with the arrow keys (↑ ↓).
Page 271
DP-1510P/1810P /1810F/2010E F9 Mode Service Item Function Mode Unit 07 Firmware 00 Host Program (4MB) Updates the firmware in the machine with Maintenance Update the Master Firmware Card. 01 Host Part A (2MB) 02 Host Part B (2MB) 03 PDL Board (2MB) 04 LAN Board (2MB) 05 PC →...
DP-1510P/1810P /1810F/2010E 5.2. Service Modes (For Facsimile) Note: This function is available for DP-1810F Only. 5.2.1. Service Mode Table The following service modes are provided to assist you in setting operational functions of the unit and determining the condition of the unit.
Page 273
DP-1510P/1810P /1810F/2010E 5.2.2. Service Mode 1 (Function Parameter Setting) Use the following procedure to change the function parameters. Service Mode 1 : For DP-1810F Step Operation or Unit Condition LCD Display Standby MMM-dd-yyyy 15:00 Press “FUNCTION” and then “7”. SET MODE (1-4) ENTER NO.
Page 274
DP-1510P/1810P /1810F/2010E Function Parameter Table Parameter Selections Function 000 MON/TEL DIAL 1 = Monitor Selects whether the machine starts to TX 2 = TEL/DIAL automatically during On-Hook dialing. Monitor : Start to TX after pressing START TEL/DIAL : Start to TX automatically 001 ALARM STATUS 1 = OFF Selects the No Paper or No Toner alarm status.
Page 275
DP-1510P/1810P /1810F/2010E Function Parameter Table Parameter Selections Function 014 G3 TX EQL 1 = 0dB Selects the cable equalizer for G3 transmission 2 = 4dB mode, 0dB, 4dB, 8dB or 12dB. 3 = 8dB 4 = 12dB Not Used 017 TX START...
Page 276
DP-1510P/1810P /1810F/2010E Function Parameter Table Parameter Selections Function 029 REMOTE 1 = Off (will not accept) Selects whether the machine accepts Remote DIAGNOSTICS 2 = On (accepts) Diagnostics from the service station. 030 CED & 300 bps 1 = 75 ms...
Page 277
DP-1510P/1810P /1810F/2010E Function Parameter Table Parameter Selections Function Not Used 050 RING DETECT 1 = Normal Selects the quality of ringer detection. Use if the line MODE 2 = Rough signal is out of regulation, set to "Rough" so that the unit may detect the ringing signals.
Page 278
DP-1510P/1810P /1810F/2010E Function Parameter Table Parameter Selections Function 070 LINE ERROR 1 = 128 lines 1. Selects the line disconnect condition during 2 = 256 lines reception. If the number of line errors exceed this 3 = 512 lines setting, the unit will disconnect the line.
Page 279
DP-1510P/1810P /1810F/2010E Function Parameter Table Parameter Selections Function 087 DARKER LEVEL 0 = Lightest Contrast Selects the contrast level. →15 0← 088 NORMAL Lightest← →Darkest 15 = Darkest Contrast LEVEL 089 LIGHTER LEVEL Not Used 092 SMOOTHING 1 = Off Selects whether the smoothing function is available.
Page 280
DP-1510P/1810P /1810F/2010E Function Parameter Table Parameter Selections Function 135 JOB END 1 sec. Selects the Guard Timer while printing data with the TIMER PDL Printer Driver ver. 6. 999 sec. Not Used 160 VERSION Indicates the ROM version PDL Firmware version on the FRM PC Board.
Page 281
DP-1510P/1810P /1810F/2010E 5.2.3. Service Mode 3 (Printout of Lists, Reports and Test Results) From this Service Mode you can print the Function Parameter List, Page Memory Test, Printer Report, All Document File, Protocol Trace and the Toner Order Form. 5.2.3.1.
Page 282
047 RESPONSE WAIT:[55sec] 55sec 097 ---------- 048 --------- 098 ---------- 049 --------- 099 ---------- Note:The power must be reset for the new parameter settings to take effect. -PANASONIC DP-1810F- ******************************** -PANASONIC DP-1810F - ****** -12345678901234567890- *********** Edition 2.0 APR 2002...
Page 283
199 ---------- Note:The power must be reset for the new parameter settings to take effect. -PANASONIC DP-1810F- ******************************** -PANASONIC DP-1810F - ****** -12345678901234567890- *********** Note: 1. [ ] - Factory Default 2. The contents of the Function Parameter List may vary depending on the country’s regulations.
Page 284
DP-1510P/1810P /1810F/2010E 5.2.3.2. Page Memory Test A test pattern prints out for checking the page memory (IC120 and IC121 on the SC PCB) and printer mechanism using the following procedure. Service Mode 3 for DP-1810F - Page Memory Test Step...
Page 285
DP-1510P/1810P /1810F/2010E MMM-dd-yyyy 15:00 VERSION: DP-1810F AAV11502AU LBP ROM VERSION :400046 MEMORY SIZE: (2MB) TX/RX/PRT/CPY:000123/000456/000789/000333 SHIPMENT SET Edition 2.0 APR 2002...
Page 286
DP-1510P/1810P /1810F/2010E 5.2.3.3. Printer Report All printer errors are logged on the Printer Report which can be printed by the following procedure. Service Mode 3 for DP-1810F - Printer Report Step Operation or Unit Condition LCD Display Standby MMM-dd-yyyy 15:00 Press “FUNCTION”...
Page 287
DP-1510P/1810P /1810F/2010E **************-PRINTER REPORT-********************* DATE MMM-dd-yyyy ***** TIME 19:02******** LAST PRINT ERROR : MMM-dd-yyyy 15:38 J00 00-00000016 CUSTOMER ID : 1234567890123456 FIRMWARE VERSION HOST : DP-1810F AAV12900AU PRINTER : 610050 TRANSMIT COUNTER : 000475 RECEIVE COUNTER : 000398 COPY COUNTER...
Page 288
DP-1510P/1810P /1810F/2010E 1. Printer Error Detail Explanation Recording Paper Jam Detection (From 1st Tray to Inner Tray 1) Feed Solenoid (nADF1) Recording Paper A sec Size Setting Ledger Legal A4-R Letter Letter-R Invice Timing Sensor (nRSENA) 0.36s Timing Sensor did not turn ON...
Page 290
DP-1510P/1810P /1810F/2010E LSU Error Detection nPRINT Print Start nPMON (CN701, 11) Polygon Motor ON nPMRDY (CN701, 10) Normal Condition Polygon Motor Ready Motor ON 5 sec 20 sec E1-22 nPMRDY Polygon Motor does not reach constant speed during wake up state.
Page 291
DP-1510P/1810P /1810F/2010E Out of Toner Detection Toner Sensor Output Signal Status A (Enough toner in the cartridge) Max. - min. voltage is less than 1.0V Min. voltage is more than 1.4V Status B (Remaining toner is getting low) Max. - min. voltage is less than 0.5V Min.
Page 292
DP-1510P/1810P /1810F/2010E 5.2.3.4. All Document Files Print the document files from the Flash Memory. Service Mode 3 for DP-1810F - All Document Files Step Operation or Unit Condition LCD Display Standby MMM-dd-yyyy 15:00 Press “FUNCTION” and then “7”. SET MODE (1-4) ENTER NO.
Page 293
DP-1510P/1810P /1810F/2010E 5.2.3.5. Protocol Trace Print a Protocol Trace Report for the previous communication. Service Mode 3 for DP-1810F - Protocol Trace Step Operation or Unit Condition LCD Display Standby MMM-dd-yyyy 15:00 Press “FUNCTION” and then “7”. SET MODE (1-4) ENTER NO.
Page 294
DP-1510P/1810P /1810F/2010E *************** PROTOCOL LOG. REPORT ****************** DATE MMM-dd-yyyy ***** TIME 16:56 ******* STATUS : OK MODE : ECM-TX (STANDARD) SPEED : 9600bps 0MS/L REMOTE CAPA. : DIS 00 CE B9 C4 80 12 LOCAL CAPA. : TSI 2B 20 20 20 38 37 2B 2B 2B 2B...
Page 295
DP-1510P/1810P /1810F/2010E 5.2.3.6. Toner Cartridge Order Form The Toner Cartridge Order Form can be printed out manually by the following procedure. Service Mode 3 for DP-1810F - Toner Cartridge Order Form Step Operation or Unit Condition LCD Display Standby MMM-dd-yyyy 15:00 Press “FUNCTION”...
Page 296
< ************************************* **** The toner supply in your machine is running low **** (1) To order a replacement Cartridge from your Authorized Dealer Panasonic Corp. (2) by Phone: 1 201 111 5555 (3) by Fax: 1 201 111 4444 (4) Thank you for your order.
Page 297
DP-1510P/1810P /1810F/2010E 5.2.4. Service Mode 4 (Modem Test) 5.2.4.1. Binary Signal This Service Mode is used to check the binary signal output. Signals can be output to the line using the following procedure. Service Mode 4 for DP-1810F - Binary Signal...
Page 298
DP-1510P/1810P /1810F/2010E 5.2.4.2. Tonal Signal This Service Mode is used to check the tonal signal output. Signals can be output to the line using the following procedure. Service Mode 4 for DP-1810F - Tonal Signal Step Operation or Unit Condition...
Page 299
DP-1510P/1810P /1810F/2010E 5.2.4.3. DTMF Signal This Service Mode is used to check the DTMF (Dual Tone Multi Frequency) signal output. The DTMF signal can be generated using the following procedure. Sevice Mode 4 for DP-1810F - DTMF Signal Step Operation or Unit Condition...
Page 300
DP-1510P/1810P /1810F/2010E DTMF Single Tone Table Number DTMF Signal Tones 697 Hz 770 Hz 852 Hz 941 Hz 1209 Hz 1336 Hz 1477 Hz 1633 Hz DTMF Dual Tone Table Number DTMF Dual Tones 941 Hz + 1336 Hz 697 Hz + 1209 Hz...
Page 301
DP-1510P/1810P /1810F/2010E 5.2.4.4. Binary Signal (V.34) This Service Mode is used to check the binary signal output. Signals can be output to the line using the following procedure. (V.34) Service Mode 4 for DP-1810F - Binary Signal Step Operation or Unit Condition...
Page 302
DP-1510P/1810P /1810F/2010E 5.2.5. Service Mode 6 (RAM Initialization) Initializes RAM and restores the Function Parameters to their default values. Note: This operation should be performed when the unit is first installed. Service Mode 6 for DP-1810F Step Operation or Unit Condition...
Page 303
DP-1510P/1810P /1810F/2010E 5.2.6. Service Mode 8 (Check & Call) 5.2.6.1. Overview This feature enables the Authorized Servicing Dealers to manage and improve the machine maintenance to their customers by alerting them of equipment problems. It also can be used as a Supply Sales Tool by alerting the Dealer that the unit is running Low on Toner.
Page 304
DP-1510P/1810P /1810F/2010E Printer Info. Error Log Only Content of Error Code Report Code E4-10 Exhaust fan motor (1) does not rotate. E5-11 Fuser Thermistor and Toner sensor error. E5-12 Main CPU/LPC interface error. E5-22 Finisher/LPC unit interface error. E7-10 Sub CPU System error.
Page 305
DP-1510P/1810P /1810F/2010E Printer Info. Error Log Only Content of Error Code Report Code No Toner Cartridge is installed. Low Toner 1st Feed Cover Open. 2nd Feed Cover Open. 3rd Feed Cover Open. 4th Feed Cover Open. Paper Transport Unit Open.
Page 306
DP-1510P/1810P /1810F/2010E 5.2.6.3. Setting Operation 8:CHECK & CALL PRESS SET TO SELECT SET or START FAX/EMAIL SET or START CHECK & CALL (1-9) SERVICE ALERT FAX # SERVICE ALERT MAIL # CLEAR CLEAR 1:SVC. ALERT FAX # Enter a destination fax number (Max. 36 digits) or an email address (Max.
Page 307
DP-1510P/1810P /1810F/2010E Note 1. Service Alert Report To enable the automatic transmission of Service Alert Report, enter the destination fax telephone number or the email address in the “SERVICE ALERT (FAX # or MAIL #)" field. When a printer error occurs, the Service Alert Report is transmitted to the designated number automatically.
Page 308
DP-1510P/1810P /1810F/2010E 5.2.6.4. SERVICE ALERT REPORT FORMAT *************************************************** DATE MMM-dd-yyyy ***** TIME 19:00 ******** **************************** > SERVICE ALERT REPORT < **************************** LAST PRINT ERROR : MMM-dd-yyyy 18:30 E03-20 41 00-00000835 CUSTOMER ID : ABC COMPANY FIRMWARE VERSION HOST : DP-1810F AAV12900PU...
Page 309
DP-1510P/1810P /1810F/2010E 5.2.6.5. MAINTENANCE ALERT REPORT FORMAT *************************************************** DATE MMM-dd-yyyy ***** TIME 12:00 ******** **************************** > MAINTENANCE ALERT REPORT < **************************** LAST PRINT ERROR : MACHINE IS RUNNING OUT OF TONER (1) CUSTOMER ID : ABC COMPANY (2) FIRMWARE VERSION...
Page 310
< ************************************* **** The toner supply in your machine is running low **** (1) To order a replacement Cartridge from your Authorized Dealer Panasonic Corp. (2) 1 201 111 5555 (3) by Phone: by Fax: 1 201 111 4444 (4) Thank you for your order.
Page 311
DP-1510P/1810P /1810F/2010E 5.2.7. Service Mode 9 (System Maintenance) 5.2.7.1. Overview This Service Mode is used to maintain and/or update the firmware of the machine. Use the following procedure for System Maintenance. Service Mode 9 for DP-1810F Step Operation or Unit Condition...
Page 312
DP-1510P/1810P /1810F/2010E 5.2.7.2. Operation 9:SYSTEM MAINTENANCE PRESS SET TO SELECT START Display card version SET or START SYSTEM MAINT.(1-8) DP-XXXAAV12300PU FIRMWARE UPDATE SET or START CLEAR CLEAR 1:FIRMWARE UPDATE PRESS SET TO START * IN PROGRESS * * If the card is not installed, SET/START will be refused.
Page 313
DP-1510P/1810P /1810F/2010E 5.2.7.3. Send Received File This function is the relief mode which makes it possible to retrieve memory received documents during a fatal printer error by transferring the documents to another fax machine. MMM-dd-yyyy 15:00 FUNC MON X 4 SERVICE MODE ENTER NO.
DP-1510P/1810P /1810F/2010E 6 System Description 6.1. Mechanical Operation 6.1.1. Scanning Mechanism (Flatbed) 1. Scanning Mechanism The Scanning Mechanism consisting of Lens, CCD PC Board Assembly, Mirrors (551,552), Scanner Lamp (501), Lamp Base Bracket (516) and Mirror 2 Bracket (525), is used to scan originals.
Page 315
DP-1510P/1810P /1810F/2010E 3. Drive Mechanism During scanning, the Lamp Base Bracket (516) and Mirror 2 Bracket (525) move in the direction of the Black arrow and while returning to standby position, it moves in the direction of the White arrow as shown in the illustration below.
DP-1510P/1810P /1810F/2010E 6.2. Automatic Document Feeder The ADF (Automatic Document Feeder) automatically feeds paper into the unit, one original at a time. Its main features are: 1. Place originals Face-Up 2. Correct Order Stacking (Collation Mode) 3. Paper Feed Mechanism with Pre Feed Roller The following is the ADF Mechanical operation description.
DP-1510P/1810P /1810F/2010E 6.3. Inverting Automatic Document Feeder The i-ADF automatically inverts two-sided original(s) for faxing or copying of the second side. This feature enables machines with a duplexer mounted to perform duplex copying. An i-ADF (Inverting Automatic Document Feeder) functions in a similar manner as the ADF (Automatic Document Feeder), with the main exception being the document eject path after scanning.
DP-1510P/1810P /1810F/2010E 6.4. Receive Mechanism 6.4.1. Paper Feed Modules 1. Paper Feed Module < NP Sensor Operation > NP Actuator (1215) Photo Sensor (604) for NP a. The NP Actuators (1215) attached to the Paper Feed Block determine if there is Recording Paper in the Recording Paper Tray.
Page 321
DP-1510P/1810P /1810F/2010E < Paper Feed Module Operation > Registration Roller (1162) Clutch (1141) Timing Actuator (1146) Photo Sensor (604) for Registration Feed Roller (1213) C25 Gear Roller (1207) C25 Separation Roller (1207) a. When the printing operation begins, the Drive Motor (1105) starts driving the Gears.
Page 322
DP-1510P/1810P /1810F/2010E < Paper Feed Module (Optional) Operation > Clutch (1141) Intermediate Roller (1617) Photo Sensor (604) for Registration 2nd Paper Feed Actuator (1624) Feed Roller (1213) C25 Gear Roller (1207) C25 Separation Roller (1207) a. When the printing operation begins, the Drive Motor (1105) starts driving the Gears.
Page 323
DP-1510P/1810P /1810F/2010E < Paper Feed Module Lift up Mechanism > Photo Sensor (604) for NP Feed Roller (1213) C25 Gear Roller (1207) Lift Plate (1316) Bottom Plate (1313) a. When inserting the Paper Tray into the machine, the Photo Sensor (604) for NP activates. At the same time, the Lift Plate (1316) is combined with the coupling which drives the Lift Plate of the machine.
Page 324
DP-1510P/1810P /1810F/2010E < Paper Feed Module Recording Paper Size Setting > Lift Motor Assembly (1238) Photo Sensor (604) For Paper Tray Detection a. The Recording Paper size in the Paper Feed Module is set on the Control Panel. Edition 2.0...
Page 325
DP-1510P/1810P /1810F/2010E 2. Sheet Bypass < NP Sensor Operation > a. The NP Actuator attached to the Paper Feed Unit determines if there is Recording Paper in the paper tray. b. The Recording Paper in the paper tray lowers the NP Actuator and the Photo Sensor (604) for NP actuates.
Page 326
DP-1510P/1810P /1810F/2010E 6.4.2. Printing Process Operation The Printing Process Operation consists of Process Unit and Toner Bottle with Toner supplied. Toner is supplied to the Process Unit using gravity. The Process Unit includes the Toner Paddle and Mag Roller (1048) that supplies Toner to the OPC Drum (1001).
Page 327
DP-1510P/1810P /1810F/2010E Exposure A portion of the laser beam is deflected to the timing sensor [Beam Detection (BD) Sensor], which controls the start timing of scanning on the OPC Drum. The CPU also uses the timing sensor to detect abnormal signals. The light beam from the laser diode is modulated by the digital signal and converted to parallel light waves by the collimator lens.
Page 328
DP-1510P/1810P /1810F/2010E 6.4.3. Laser Unit F Lens Lens LSU Chassis Polygon Mirror / Polygon Motor Collimator Lens Aperture Collimator Lens Laser Beam Detection Beam Detection Beam Detection Sensor Reflection Mirror Lens 1. Laser This Laser uses the semiconductor laser. The beam power on the drum surface is approximately 0.20 2.
Page 329
DP-1510P/1810P /1810F/2010E 6.4.4. Fuser Operation The Recording Paper passes through the Fuser Roller (913) and is subjected to heat and pressure in the Fuser Unit. Pressure between the Fuser Roller (913) and Pressure Roller (914) fuses or bonds the toner into the paper.
Page 330
DP-1510P/1810P /1810F/2010E Separators (923) Five Separators (923) are installed in the Fuser Roller (913). This prevents the recording paper from wrapping around the Fuser Roller (913), causing a paper jam. When the Fuser Unit does not reach the specified temperature within a certain period of time, an Error code is shown on the display, stopping the operation.
Page 332
DP-1510P/1810P /1810F/2010E 6.5.2. System Control Circuit The System Control Block consists of the following IC that control the general functions. A-BUS 3V PanelCPU F-ROM 4MB CPU SH2 (IC1) Program Scanning (IC10) Mechanism Control CPU DRAM 2MB (IC7) F-ROM 2MB MA-BUS 3V...
Page 333
DP-1510P/1810P /1810F/2010E 1. System CPU The System CPU (SH7041) is a 32-bit RISC (Reduced Instruction Set Computer) type of CPU and DMA Control, Serial Communication Port, Timer Control, Interrupt Control, DRAM Control, and I/O Port are integrated into 1 chip. Mask ROM (64k byte) is already installed and it controls the Monitor, High Speed managing Task and Boot Programming.
Page 334
DP-1510P/1810P /1810F/2010E 6.5.3. Image Data Circuit The Image Data Circuit is independent of System circuit from Page Memory / Sort Memory circuit due to high speed scanning and printing. As a result of this, all image data is managed by the Image Data circuit and only coded data is transferred to the System Data BUS.
Page 335
DP-1510P/1810P /1810F/2010E 1. Document Adaptor for New Copier Engine (Gate Array) DZAC000234 (DANCE) is a Document Adaptor for New Copier Engine (Gate Array) and provides the Image Control peripheral function and Recording Data Control. • DMA Control It is used to transfer data between the following devices.
Page 336
DP-1510P/1810P /1810F/2010E • Synchronization Control Circuit This circuit is used to synchronize the output of the recorded data with the horizontal synchronizing output signal from the printer for each line. The IPC controls the resolution of the printer as follows.
Page 337
DP-1510P/1810P /1810F/2010E 6.5.4. Scanning Circuit CCD(DZEP000471) SC(DZEP000604) CNP120 CNP51 MN86076(IC51) Binary Binary Data uPD3747 CNP106 Error Analog (COPY) (IC1) Diffusion Master Converter (IC54) (IC55) Gray Gray Scale Scale Data (PC Scanner) Analog Front End CNP8 SLA7042M SCANNING MOTOR (IC70) CNP9...
Page 338
DP-1510P/1810P /1810F/2010E 6.5.5. Coding Coding and decoding (MH/MR/MMR/JBIG conversion) is carried out by the hardware codec device. • PM-22c (IC33) : for Image Codec It codes or decodes the data transferred from Sort memory. When copying, this codec codes from the Image data to JBIG data.
Page 339
DP-1510P/1810P /1810F/2010E 6.5.7. Sleep Mode Note: When the 10/100 Ethernet Interface / Internet Fax Kit is installed, the Sleep Mode is disabled. This function reduces the power consumption in standby mode. During Sleep Mode, power is supplied only to the Energy Saver Lamp to keep it at a steady ON condition, and to the circuit that monitors it The power is recovered the Energy Saver key is pressed.
Page 340
DP-1510P/1810P /1810F/2010E 6.5.8. Signal Routing 1. Memory Transmission (DP-1810F only) S-DRAM DRAM S-DRAM Sort (Work) Memory Page Memory FROM (Image) Inside SRAM FROM(Font ROM) Font DRAM (Buffer) : OTI Data FROM (Image) Program Transfer DRAM (Line Memory) : Coded Data...
Page 342
DP-1510P/1810P /1810F/2010E 5. Scan into Memory S-DRAM DRAM S-DRAM Sort (Work) Page Memory Memory FROM (Image) Note: 1) For Sort Copy, Steps & 2) For Fax, Steps for DP-1810F only. 6. File Print from Memory S-DRAM S-DRAM DRAM Sort (Work)
Page 343
DP-1510P/1810P /1810F/2010E 7. Report/List Printing S-DRAM S-DRAM DRAM Sort (Work) Page Memory Memory FROM (Image) Note: For Sort Copy Print, from 8. PC Scanning Mode (Binary/Gray Scale Scanning) D-BUS +3V MN86076 ANALOG FRONT END BRIDGE (DZAC000233) DRAM SH7041 S-DRAM S-DRAM...
Page 345
DP-1510P/1810P /1810F/2010E 6.5.9. Panel PC Board This Panel PC Board consists of Panel Control Sub-CPU, LED, and Key Switch. The Sub-CPU receives the command of async serial data from SC PCB and executes LCD Display, LED Lamp, Switching Scan, Key Touch Sound, and Alarm Sound. The signal nPSAVE is turned to LOW with the command from SC PCB and shifts to Sleep Mode.
Page 346
DP-1510P/1810P /1810F/2010E The machine will emerge from Sleep Mode under the following conditions: 1. Push on Energy Saver Key 2. Original Sensor Actuated (ADF Option) 3. Data Signal from Printer I/F 4. Platen Cover Open 5. Ringing Signal Detected (DP-1810F only).
Page 347
DP-1510P/1810P /1810F/2010E 6.5.10. Laser Printer Motor Drive Circuit 1. System Description It consists of 16 bit CPU M30802. The CPU controls mechanism of Laser Printer, Fuser Lamp temperature, and Laser Unit. 2. Reset Circuit This circuit consists of IC301 (PST575E) and peripheral circuit. This circuit always watches 5V. Output of this circuit (nRST) is set that if 5V falls below setting level (3.9V).
Page 348
DP-1510P/1810P /1810F/2010E 3. Printer Motor Drive Circuit This Printer Motor is a Brushless DC Motor. nMMON When the signal level goes Low, the Printer Motor starts rotating. nMMRDY Rotation status signal for Printer Motor. When the Printer Motor reaches a constant speed, nMMRDY signal level goes Low.
Page 349
DP-1510P/1810P /1810F/2010E 4. Fuser Lamp Drive Circuit It consists of 1 Fuser Lamp and Fuser Lamp is controlled by the HTC PC Board. The Fuser Lamp is powered by 100 VAC. When the CN766, Pin 2 (nSSR) on the HTC PCB goes LOW, the Fuser Lamp turns ON.
Page 350
DP-1510P/1810P /1810F/2010E 5. Fuser Temperature Control Circuit The fuser temperature is controlled by IC1 on the LPC3 PC Board, which contains A/D (Analog/Digital) converters. IC1 adjusts temperature, observing Thermistor and voltages separated by R61 with A/D converters. When the PC101 drive current is transmitted from the LPC3 PC Board to the HTC PCB, the Fuser Lamp turns ON.
Page 351
DP-1510P/1810P /1810F/2010E 6. Interlock Safety Circuit This safety circuit turns OFF the +24 VDC and +5 VDC supply voltages when the Front Door Cover is opened. When the Front Door Cover is opened, the microswitch(es) on the ILS PC Board are de- actuated, turning OFF +24 VDC to the Printer Motor Drive Circuit, the HVPS, the Paper Feed Solenoid Circuits, the Clutch Drive Circuit, and the Laser Driver Circuit on the Laser Unit.
Page 352
DP-1510P/1810P /1810F/2010E 7. LSU Control Circuit The laser control signals are described below. Actual data is sent from SC PCB to LSU. VIDEO+ Actual data is outputted by these 2 signals. VIDEO- nS/H Laser Power Sample/Hold Timing Signal. nHSYNC : This horizontal synchronization signal transmitted from the Beam Detection Sensor sets the horizontal position of the laser beam as it crosses the OPC Drum.
DP-1510P/1810P /1810F/2010E 7 Installation 7.1. Precautions During Set Up Copy machine performance and the copy quality is subject to and dependant on environmental conditions. To maintain good performance, quality, and safe operation, observe the following precautions: 1. For safe operation and to avoid trouble, do not install the system under the following conditions: •...
Page 354
DP-1510P/1810P /1810F/2010E Installation Procedure 7.3.1. (1) Open the Platen Cover or the ADF. (2) Remove 3 Silver Screws. (3) Remove the Left Platen Cover. (4) Remove the Orange Tape. (5) Remove 1 Blue Screw. (6) Remove the Metal Shipping Bracket by rotating counter-clockwise.
Page 355
DP-1510P/1810P /1810F/2010E (11) Open the Right Cover. (12) Remove the Protective Sheet. Protective Sheet (13) Release 2 Pressure Levers as illustrated. Left Right Stopper Locked Stopper Released [Right Side View] (14) Remove the Protection Paper from the Process Unit. (14)
Page 356
DP-1510P/1810P /1810F/2010E (17) Align the Key of the Toner Bottle with the Key Alignment Channel of the Bottle Holder. (18) Insert the Bottle as far as it will go, then while holding the Bottle Holder in place, turn the Toner Bottle clockwise (160°, approx.
DP-1510P/1810P /1810F/2010E 7.4. Adjustment 7.4.1. Exposure (Standard Adjustment) The following values will be added to the reference value. DO NOT adjust these codes in the field. F6-18 : Laser power compensation F6-19 : Developer bias standard voltage compensation 1. Press “FUNCTION”, “ORIGINAL SIZE”, and “3” keys sequentially to enter the Service Mode.
Page 358
DP-1510P/1810P /1810F/2010E 7.4.3. Leading Edge Adjustment (Scanner) (1) Make sure that the Scanner Unit is at initial position. (2) Remove 3 Silver Screws and remove Left Platen Cover. (3) Loosen the Left edge Screw (A) turning counter-clockwise 1 or 2 rounds.
Installation Note: 1. With this Option, the DP-1510P/1810P/2010E can be used as a Network Printer and the DP-1810F as an Internet-Fax & Network Printer. 2. Turn the Power Switch to the OFF (O) position and unplug the AC Power Cord before beginning installation.
Page 360
DP-1510P/1810P /1810F/2010E (3) Secure the LANB PC Board onto the Bracket with 3 Screws (XYN3+F8). (4) Connect the LANB-LANC Harness to CN5 and CN6 on the LANB PC Board. (5) Install the LANB PC Board Assembly. (6) Secure the LANB PC Board Assembly with 2 Screws (XTB3+8J).
Page 361
DP-1510P/1810P /1810F/2010E Note: (12) Remove the LANC PC Board from LANC BK Assembly (DZHP004034). (11) (LANC Bracket : DZJB000166 : Not used) (11) Connect the LANB-LANC Harness to CN200 on (12) the LANC PC Board. (12) Install the LANC PC Board and secure with 2 Screws (XYN3+F8).
DP-1510P/1810P /1810F/2010E 8.2. Installing the PCL6 Emulation Kit (DA-PC210) 8.2.1. Contents Required for DP-1510P/1810P/1810F/2010E Qty. Description Part No. Remarks EP PC Board w/FRM PCB DZEC101289 Locking Spacer DZJH000063 Bracket, PDL DZJB000339 Screw XTB3+8J Screw XYN3+F8 Software CD See Note 2...
Page 363
DP-1510P/1810P /1810F/2010E (4) Insert the Locking Spacer (DZJH000063) into the mounting hole on the machine chassis. (5) Install the EP PC Board Assembly. (6) Insert the Locking Spacer into the EP PC Board Assembly. (7) 1 Screw (XTB3+8J). (8) Proceed with the installation of other options.
DP-1510P/1810P /1810F/2010E 8.4. Installing the Automatic Document Feeder (DA-AS180) for DP-1510P/1810P/2010E 8.4.1. Contents Qty. Description Part No. Remarks Automatic Document Feeder (ADF) See Note Standard on DP-1810F Angle Plate DZJA000858 Scanning Pad DZHP006374 Screw DZPB000007 Screw XTB3+12J Installation Instructions DZSM000523 Note: The part number differs depending on the Destination.
Page 366
DP-1510P/1810P /1810F/2010E (4) Remove 7 Screws. (5) Remove the Rear Plate. (6) Bend the protective Tab on the Rear Plate further than 90° as illustrated on the left. (7) Connect the Harness to CN3 on the SC PC Board. (8) Insert the Harness Clamp into a pre-drilled hole in the frame (from underside).
Page 367
DP-1510P/1810P /1810F/2010E (11) Peel off the 2 adhesive protectors from the (13) Scanning Pad. (12) Place the Scanning Pad on the glass, aligning with the upper left corner, keeping 1mm space as shown on the left. (13) Close the ADF.
Page 368
DP-1510P/1810P /1810F/2010E (21) If the Document is Skewed to the left, set the <Example of Printed Image> Adjusting Bracket to the left and secure with 1 Document Leading Screw. Edge Left Skewed to the left Edition 2.0 APR 2002...
Page 369
DP-1510P/1810P /1810F/2010E Printed Adjustment Adjustment Document Remarks Image Amount No. 90 0.2mm After setting ADF Detection the Parameter, 1 Point Timing reboot the machine (ADF Image to enable the 0.2mm Read Start Paper Parameter Position Travel Setting. Adjustment) 1 Point No.
DP-1510P/1810P /1810F/2010E 8.5. Installing the Inverting Automatic Document Feeder (DA-AR201) for DP-2010E 8.5.1. Contents Qty. Description Part No. Remarks Inverting Automatic Document Feeder See Note For DP-2010E (i-ADF) Scanning Pad DZJM000428 Hinge Stopper DZJA000726 Hinge Cover DZMC000713 ADF Mounting Bracket...
Page 371
DP-1510P/1810P /1810F/2010E (3) Using a Slotted Blade Screwdriver, remove the OPS Actuator as illustrated. (4) Install the i-ADF OPS Actuator. (5) Install the 2 ADF Mounting Brackets. (6) Secure the 2 brackets with 6 Screws (XTB3+12J) as illustrated. Note: The remaining 2 Screws (XTB3+12J) will be installed in step (20).
Page 372
DP-1510P/1810P /1810F/2010E (8) Install the i-ADF on top of the ADF Mounting Brackets. Note: a. Set the i-ADF in the direction of the arrow. b. Align the hallmark on the right side of the Hinge Base and the ADF Mounting Bracket as illustrated.
Page 373
DP-1510P/1810P /1810F/2010E (20) Secure the i-ADF Rear Support Bracket with 4 Screws (XTB3+8J). (21) (21) Secure the i-ADF Rear Support Bracket with 2 Screws (XTB3+12J). (20) (22) Using a 20 lb (80 g/m2) lined original, make a < Example of Printed Image >...
Page 374
DP-1510P/1810P /1810F/2010E (25) If there is no space, adjust the Platen Glass position by following the procedure below: a. Open the ADF Unit. b. Remove 3 Silver Screws. c. Remove the Left Platen Cover. d. Loosen 2 Screws. e. Shift the Scanning Glass Guide to the left and tighten the 2 Screws.
Page 375
DP-1510P/1810P /1810F/2010E Printed Adjustment Adjustment Document Remarks Image Amount No. 90 0.2mm After setting ADF Detection the Parameter, 1 Point Timing reboot the machine (ADF Image to enable the 0.2mm Read Start Paper Parameter Position Travel Setting. Adjustment) 1 Point No.
Note: The part number differs depending on the Destination. Refer to the Parts Manual. 8.6.2. Installing the 2nd Paper Feed Module for the DP-1510P/1810P/1810F/2010E (Except DP-2010E for USA and Canada) Note: Turn the Power Switch to the OFF (O) position and unplug the AC Power Cord before beginning installation.
Page 377
DP-1510P/1810P /1810F/2010E (2) Remove 7 Silver Screws. (3) Remove the Rear Plate. (4) Install 2 Guide-Pins. (5) Place the machine on top of the 2nd Paper Feed Module as illustrated on the left. (6) Secure the 2nd Paper Feed Module with 5 Screws (XTB3+8J).
Page 378
DP-1510P/1810P /1810F/2010E (7) Remove 2 Silver Screws (2nd Paper Feed Module). (8) Remove the CST Rear Cover. (9) Connect one end of the CST4 Harness (with Ferrite Core) to CN731 on the LPC3 PC Board. (10) Insert the other end of the harness through the bottom opening in the frame.
Page 379
DP-1510P/1810P /1810F/2010E 8.6.3. Installing the 2nd and 3rd Paper Feed Modules Together for DP-1810F/2010E (Except DP-2010E for USA and Canada) Note: Turn the Power Switch to the OFF (O) position and unplug the AC Power Cord before beginning installation. (1) Slide the Paper Tray all the way out.
Page 380
DP-1510P/1810P /1810F/2010E (8) Slide the 2nd Paper Tray all the way out. (9) Place the 2nd Paper Feed Module on top of the 3rd Paper Feed Module as illustrated on the left. (10) Secure the 2nd Paper Feed Module with 5 Screws (XTB3+8J).
Page 381
DP-1510P/1810P /1810F/2010E (14) Secure the 2nd Paper Feed Module with 5 Screws (XTB3+8J). (14) (14) (14) (15) Remove 2 Silver Screws (3rd Paper Feed Module). (16) Remove the CST Rear Cover. (16) (15) (17) Connect one end of the CST4 Harness (with Ferrite Core) to CN731 on the LPC3 PC Board.
Page 382
DP-1510P/1810P /1810F/2010E 8.6.4. Installing the 3rd Paper Feed Module for DP-2010E (For USA and Canada) Note: Turn the Power Switch to the OFF (O) position and unplug the AC Power Cord before beginning installation. (1) Slide the 2nd Paper Tray all the way out.
Page 383
DP-1510P/1810P /1810F/2010E (6) Secure the 3rd Paper Feed Module with 5 Screws (XTB3+8J). (7) Remove 2 Silver Screws (3rd Paper Feed Module). (8) Remove the CST Rear Cover. (9) Connect one end of the CST4 Harness (with Ferrite Core) to CN777 on the CST4 PC Board of the 2nd Paper Feed Module.
Page 384
DP-1510P/1810P /1810F/2010E 8.6.5. Installing the 2nd, 3rd and 4th Paper Feed Modules Together for DP-1810F/2010E (Except DP-2010E for USA and Canada) Note: Turn the Power Switch to the OFF (O) position and unplug the AC Power Cord before beginning installation.
Page 385
DP-1510P/1810P /1810F/2010E (8) Slide the 2nd and 3rd Paper Trays all the way out. (9) Place the 3rd Paper Feed Module on top of the 4rd Paper Feed Module and then place the 2nd Paper Feed Module on top of the 3rd Paper Feed Module as illustrated on the left.
Page 386
DP-1510P/1810P /1810F/2010E (14) Secure the 2nd Paper Feed Module with 5 Screws (XTB3+8J). (14) (14) (14) (15) Remove 4 Silver Screws (3rd and 4th Paper Feed Modules). (16) Remove 2 CST Rear Covers. (15) (16) (17) Connect one end of the CST4 Harness (with Ferrite Core) to CN731 on the LPC3 PC Board.
Page 387
DP-1510P/1810P /1810F/2010E (27) Set the Paper Size Guide. (28) Secure with 3 Screws which are stored inside of the Paper Tray, if necessary. Edition 2.0 APR 2002...
Page 388
DP-1510P/1810P /1810F/2010E 8.6.6. Installing the 3rd and 4th Paper Feed Modules Together for DP-2010E (For USA and Canada) Note: Turn the Power Switch to the OFF (O) position and unplug the AC Power Cord before beginning installation. (1) Slide the 2nd Paper Tray all the way out.
Page 389
DP-1510P/1810P /1810F/2010E (8) Install 2 Guide-Pins. (9) Place the machine on top of the 3rd Paper Feed Module as illustrated on the left. (10) Secure the 3rd Paper Feed Module with 5 Screws (XTB3+8J). (10) (10) (10) (11) Remove 4 Silver Screws (3rd and 4th Paper Feed Modules).
Page 390
DP-1510P/1810P /1810F/2010E (13) Connect one end of the CST4 Harness (with Ferrite Core) to CN777 on the CST4 PC Board of the 2nd Paper Feed Module. (14) (14) Insert the other end of the harness through the bottom opening in the frame.
DP-1510P/1810P /1810F/2010E 8.7. Installing the Handset Kit 8.7.1. Contents Qty. Description Part No. Remarks Handset See Note Handset Cord See Note Cradle Assembly See Note Handset Cradle Stopper DZSM000783 For UF-490 Only DZSM000230 For U.S.A. and Canada Installation Instructions DZSM000028...
Page 394
DP-1510P/1810P /1810F/2010E 8.8.2. Installation Note: Turn the Power Switch to the OFF (O) position and unplug the AC Power Cord before beginning installation. (1) Remove the Process Unit. (Refer to ch 2.2.1 of the Service Manual) (2) Remove the Front Cover, Inner Cover J, Left Side Cover and Rear Plate.
Page 395
DP-1510P/1810P /1810F/2010E (12) Connect the PTC Heater to the PTC-AC (12) Harness 3. (13) Route the PTC Heater to the upper compornent of the frame through the access hole as illustrated. (13) (14) Mount the PTC Heater onto the Dehumidifier (14) Bracket.
Page 396
DP-1510P/1810P /1810F/2010E (18) Install 4 Clamps as illustrated. (19) Insert the PTC-AC Harness 3 into 3 Clamps. (18) (19) (20) Move the Lamp Base Assembly slowly toward (20) the right, positioning the bracket near the center (Marked by (A) as illustrated).
Page 397
DP-1510P/1810P /1810F/2010E (25) Insert the Harness of the Thermistor into 3 Clamps as illustrated. (25) (25) (26) Connect the PTC-AC Harness 2 to CN173 on the RLB PC Board. (26) (27) Connect the Harness of the Thermistor and (27) PTC-AC Harness 3 to PTC-AC Harness 2.
Page 398
DP-1510P/1810P /1810F/2010E (29) Install the PTC Heater Assembly. (30) Secure the PTC Heater Assembly with 1 Screw. (30) (29) (31) Connect the PTC-AC Harness 4 to CN172 on the RLB PC Board. (32) (32) Connect the PTC-AC Harness 4 to PTC Heater...
Page 399
DP-1510P/1810P /1810F/2010E (37) Connect the PTC Heater Harness to PTC-AC (39) (39) Harness 6. (38) Remove the CST Rear Cover. (Refer to ch 8.5. of the Service Manual) (39) Install 6 Clamps as illustrated. (40) Insert the PTC-AC Harness 6 into 4 Clamps.
Page 400
DP-1510P/1810P /1810F/2010E (49) Connect the PTC-AC Harness 7 to PTC-AC Harness 8. (50) (50) Insert the other end of the harness through the bottom opening in the frame. (51) The procedure for 3rd and 4th Paper Feed Modules is the same as steps (47)~(50).
DP-1510P/1810P /1810F/2010E 8.9. Installing the Key Counter Cable Kit (DA-KH200) 8.9.1. Contents Note: The Key Counter is sold separately. Qty. Description Part No. Remarks KEY Harness DZFP000928 Longer KC Harness FFPWC0392 Shorter KC Bracket DZJA000786 Not used Screw DZPA000063 Not used...
Page 402
DP-1510P/1810P /1810F/2010E (7) Re-install the Rear Plate as shown on the left. (8) Secure the Rear Plate with 7 Screws. Edition 2.0 APR 2002...
DP-1510P/1810P /1810F/2010E 8.10. Replacing the OPC Drum (1) Open the Right Cover. (2) Open the Front Door Cover. (3) Remove the Toner Waste Container by slowly pulling it towrds the left as illustrated. (4) Seal the Container with the enclosed cap and dispose of it properly.
Page 404
DP-1510P/1810P /1810F/2010E (8) Unlock the Front OPC Bushing Assembly by turning it clockwise. (9) Push the OPC Drum forward from the rear end as illustrated. (10) (10) Remove the Front OPC Bushing Assembly. (11) Remove the OPC Drum as shown in the...
Page 405
DP-1510P/1810P /1810F/2010E (14) Reinstall the Front OPC Bushing Assembly and turn it counter-clockwise to lock it in place. (14) (15) Remove the Protective Film from the OPC Drum. (15) (16) Turn the OPC Drum Assembly in the direction of the arrow until it locks by the 2 OPC Latches.