Page 1
DSC-P32 SERVICE MANUAL LEVEL US Model Ver 1.0 2003. 02 Canadian Model Revision History Revision History AEP Model UK Model E Model Australian Model Hong Kong Model Korea Model Chinese Model Tourist Model Japanese Model Link Link SPECIFICATIONS BLOCK DIAGRAMS...
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU PUBLISHED BY SONY.
Page 3
DSC-P32 SAFETY CHECK-OUT After correcting the original service problem, perform the following safety checks before releasing the set to the customer. Unleaded solder Check the area of your repair for unsoldered or poorly-soldered Boards requiring use of unleaded solder are printed with the lead- connections.
The electric shock is caused by the charged voltage which is kept without discharging when the main power of the DSC-P32 is simply turned off. Therefore, the remaining voltage must be discharged as described below.
Page 6
• The type of memory stick that cannot be Replace the memory stick. used by this machine, is inserted. C:13:01 MS ERROR Format the memory stick with the DSC-P32. • Data is damaged. • Unformatted memory stick is inserted. Flash LED Checking of flash unit or replacement of...
DSC-P32 SECTION 2 COVER COVER HELP HELP DISASSEMBLY The following flow chart shows the disassembly procedure. SY-84 board service position DISASSEMBLY DISASSEMBLY DISASSEMBLY Discharging the Capacitor DISASSEMBLY DISASSEMBLY DISASSEMBLY HELP DISASSEMBLY DISASSEMBLY DISASSEMBLY PROCEDURE OF REMOVING SY-84 BOARD 1 2-1. CABINET (REAR) BLOCK ASSEMBLY ......
DSC-P32 NOTE: Follow the disassembly procedure in the numerical order given. 2-1. CABINET (REAR) BLOCK ASSEMBLY 6 Claw Caution The flexible board of the Control switch block(SW-390) Control switch block may be damaged if you remove the Cabinet (rear) block...
DSC-P32 2-3. MAIN BLOCK ASSEMBLY Caution The power supply capacitor of the Flash unit is charged to the voltage as high as 300 V at a maximum. The high voltage is not discharged even after the main power of the machine is simply turned off and the charged potential still remains.
DSC-P32 2-4. PARTS UNIT (UA-001), DC MOTOR 8C-023G 3 Tapping screw, p2 (1.7 × 5) 4 DC motor 8C-023G 2 Parts unit (UA-001) 1 Two tapping screws, p2 (1.7 × 5) 2-5. MEMORY STICK CONNECTOR, JK BLOCK (JK-247) 5 JK BLOCK (JK-247)
Page 13
DSC-P32 [SERVICE POSITION (SY-84 BOARD)] Cabinet (rear) block assembly Memory stick connector AC power DC IN adaptor JK BLOCK (JK-247) DC jack CN702 SY-84 board CN701 CN704 CN201 CN705 Lens (LSV-780A) “ Never remove the lens unless removal CN706 is required at the event of checking the CCD imager and others.’’...
DSC-P32 2-10.CIRCUIT BOARDS LOCATION SY-84 ST-82 Board Name Function SY-84 CCD IMAGER, CAMERA A/D CONV, LENS DRIVE, CAMERA DSP, VIDEO AMP, SH DSP, CLK GEN., FRONT CONTROL, AUDIO I/O, LCD DRIVE, TIMING GEN., DC IN, DC-DC CONVERTER CONNECTOR. ST-82 FLASH DRIVE...
DSC-P32 2-11.FLEXIBLE BOARDS LOCATION The flexible boards contained in the lens device are not shown. CONTROL SWITCH BLOCK (SW-390) CONTROL SWITCH BLOCK (RL-059) UA-001 FP-643 JK BLOCK (JK-247) FP-644 2-9E...
DSC-P32 27/Feb/2003 HELP Sheet attachment positions and procedures of processing the flexible boards/harnesses are shown. MAIN BLOCK ASSEMBLY DC motor 8C-023G (2P) HELP...
DSC-P32 COVER COVER 3. BLOCK DIAGRAMS Link Link OVERALL BLOCK DIAGRAM FRONT/LCD BLOCK DIAGRAM OVERALL BLOCK DIAGRAM FRONT/LCD BLOCK DIAGRAM CAMERA BLOCK DIAGRAM CAMERA BLOCK DIAGRAM POWER BLOCK DIAGRAM POWER BLOCK DIAGRAM...
Page 18
DSC-P32 SECTION 3 3. BLOCK DIAGRAMS 3. BLOCK DIAGRAMS COVER COVER BLOCK DIAGRAMS 3-1. OVERALL BLOCK DIAGRAM ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. SW-390 (1/2) (3/10)
Page 19
DSC-P32 3. BLOCK DIAGRAMS 3. BLOCK DIAGRAMS COVER COVER ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. 3-2. CAMERA BLOCK DIAGRAM SY-84 BOARD (1/2) (3/10) (4/10) (HM (3M SA) BOARD)
Page 20
DSC-P32 3. BLOCK DIAGRAMS 3. BLOCK DIAGRAMS COVER COVER 3-3. FRONT/LCD BLOCK DIAGRAM ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. SY- 84 BOARD (2/2) SW-390 (3/3) (FLEXIBLE)
Page 21
DSC-P32 3. BLOCK DIAGRAMS 3. BLOCK DIAGRAMS COVER COVER ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. 3-4. POWER BLOCK DIAGRAM SY- 84 BOARD CN001 F007 BATT UINREG...
DSC-P32 COVER COVER 4-2. SCHEMATIC DIAGRAMS Link Link ST-82 BOARD CONTROL SWITCH BLOCK ST-82 BOARD (FLASH DRIVE) CONTROL SWITCH BLOCK (SW-390) (FLASH DRIVE) (SW-390) FP-643 FLEXIBLE BOARD CONTROL SWITCH BLOCK FP-643 FLEXIBLE BOARD CONTROL SWITCH BLOCK (RL-059) (RL-059) JK BLOCK...
Page 25
DSC-P32 4-2. SCHEMATIC DIAGRAMS 4-2. SCHEMATIC DIAGRAMS COVER COVER THIS NOTE IS COMMON FOR SCHEMATIC DIAGRAMS (In addition to this, the necessary note is printed in each block) (For schematic diagrams) 1. Connection • All capacitors are in µF unless otherwise noted. pF : µ...
DSC-P32 4-2. SCHEMATIC DIAGRAMS 4-2. SCHEMATIC DIAGRAMS ST-82 PRINTED WIRING BOARD ST-82 PRINTED WIRING BOARD COVER COVER 4-2. SCHEMATIC DIAGRAMS For Schematic Diagram • Refer to page 4-37 for printed wiring board of ST-82 board. ST-82 BOARD NO MARK:REC/PB MODE...
Page 27
DSC-P32 4-2. SCHEMATIC DIAGRAMS 4-2. SCHEMATIC DIAGRAMS JK BLOCK FLEXIBLE BOARD JK BLOCK FLEXIBLE BOARD COVER COVER JK BLOCK(JK-247) JACK XX MARK:NO MOUNT MS_VSS MS_VSS MS_VCC MS_VCC MS_VCC MS_SCLK MS_SCLK N.C. MEMORY XMS_IN XMS_IN STICK CONNECTOR MS-DIO N.C. MEMORY STICK N.C.
Page 28
DSC-P32 4-2. SCHEMATIC DIAGRAMS 4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS 4-3. PRINTED WIRING BOARDS COVER COVER • CONTROL SWITCH BLOCK (SW-391) is replaced as a block. So that this PRINTED WIRING BOARD is omitted. CONTROL SWITCH BLOACK BT100 REG_GND...
Page 29
DSC-P32 4-2. SCHEMATIC DIAGRAMS 4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS 4-3. PRINTED WIRING BOARDS COVER COVER • CONTROL SWITCH BLOCK (RL-059) is replaced as a block. So that this PRINTED WIRING BOARD is omitted. • UA-001 UNIT is replaced as a block. So that this PRINTED WIRING BOARD is omitted.
Page 30
DSC-P32 COVER COVER 4-3. PRINTED WIRING BOARDS Link Link ST-82 BOARD JK BLOCK (JK-247) ST-82 BOARD JK BLOCK (JK-247) COMMON NOTE FOR PRINTED WIRING BOARDS COMMON NOTE FOR PRINTED WIRING BOARDS MOUNTED PARTS LOCATION CIRCUIT BOARDS LOCATION CIRCUIT BOARDS LOCATION...
Page 31
DSC-P32 4-3. PRINTED WIRING BOARDS 4-3. PRINTED WIRING BOARDS COVER COVER THIS NOTE IS COMMON FOR WIRING BOARDS (In addition to this, the necessary note is printed in each block) (For printed wiring boards) • Chip parts. • : Uses unleaded solder.
DSC-P32 4-3. PRINTED WIRING BOARDS 4-3. PRINTED WIRING BOARDS COVER COVER 4-5. MOUNTED PARTS LOCATION no mark : side A * mark : side B ST-82 BOARD * C503 * C504 * C505 Mounted parts location of the SY-84 board...
DSC-P32 COVER COVER NOTE NOTE 5. REPAIR PARTS LIST NOTE: Characters A to Z of the electrical parts list indicate location of exploded views in which the desired part is shown. EXPLODED VIEWS EXPLODED VIEWS Link Link CABINET (FRONT) SECTION...
Page 36
DSC-P32 5. REPAIR PARTS LIST 5. REPAIR PARTS LIST COVER COVER NOTE: • -XX, -X mean standardized parts, so they may have some differences from When indicating parts by reference number, the original one. please include the board name. •...
Page 37
DSC-P32 5. REPAIR PARTS LIST 5. REPAIR PARTS LIST COVER COVER 5-1. EXPLODED VIEWS 5-1-1. CABINET (FRONT) SECTION ns : not supplied Cabinet (rear) block assembly (See page 5-6) Main block assembly (See page 5-4) Ref. No. Part No. Description Remarks Ref.
Page 38
DSC-P32 5. REPAIR PARTS LIST 5. REPAIR PARTS LIST COVER COVER 5-1-2. MAIN BLOCK ASSEMBLY ns : not supplied Lens frame block assembly (See page 5-5) J101 CN101 J102 BT901 Ref. No. Part No. Description Remarks Ref. No. Part No.
Page 39
DSC-P32 5. REPAIR PARTS LIST 5. REPAIR PARTS LIST COVER COVER 5-1-3. LENS FRAME BLOCK ASSEMBLY IC351 Be sure to read “Precautions upon replacing CCD imager” on page 4-7 when changing the CCD imager. Ref. No. Part No. Description Remarks Ref.
Page 40
DSC-P32 5. REPAIR PARTS LIST 5. REPAIR PARTS LIST COVER COVER 5-1-4. CABINET (REAR) BLOCK ASSEMBLY ns : not supplied LCD901 ND901 BT100 : For the installation position of BT100 (Lithium battery), refer to page 2-3. CAUTION : Danger of explosion if battery is incorrectly replaced.
Page 42
DSC-P32 Checking supplied accessories. Make sure that the following accessories are supplied with your camcorder. Power cord (1)(AUS model) Battery charger (BC-CS2)(1) Connection cord Hand strap (1) 0 1-696-819-21 (US,CND,JE,J model) (AV Cable 1.5m)(1) 3-070-841-01 Power cord (1)(AEP,E model) 0 1-477-814-11...