Basic Settings; Setting The Digital Input (Digital In) Terminals; Selecting The Analog Or Digital Input Mode - JVC RX-5020VBK Instructions Manual

Basic Settings

Front Panel
Display
FM/AM TUNING FM/AM PRESET FM MODE
UP UP
STANDBY
MEMORY
DOWN DOWN
STANDBY/ON
D I G I T A L
S U R R O U N D
SURROUND ON/OFF
INPUT ANALOG INPUT DIGITAL
INPUT ATT
SURROUND MODE
SPEAKERS ON/OFF
PHONES
INPUT INPUT
ANALOG DIGITAL
Setting the Digital Input
[DIGITAL IN] Terminals
When you use the digital input terminals, register what components
are connected to which terminals (DIGITAL 1/2) so that the correct
source name will appear when you select the digital source.
Before you start, remember...
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
1
Press SETTING repeatedly until
"DIGITAL IN" appears on the display.
The display changes to show the current setting.
DIGITAL 2 terminal setting
S.WFR LFE
LS S RS
CH-
DIGITAL 1 terminal setting
* "1DVD 2CD" is the initial setting. If you have already
changed the setting, another combination will be shown.
2
Press CONTROL UP 5/DOWN ∞ to
select the appropriate digital terminal
setting.
• Each time you press the button, the display
changes to show the following:
1 DVD 2 CD j 1 DVD 2 TV j 1 DVD 2 CDR j
1 CD 2 DVD j 1 CD 2 TV j 1 CD 2 CDR j
2 DVD j 1 TV
1 TV
1 CDR 2 DVD j 1 CDR 2 CD j 1 CDR 2 TV j
(back to the beginning)
Note:
When shipped from the factory, the DIGITAL IN terminals can be used
as the digital input for the following components.
– DIGITAL 1 (coaxial): For DVD player
– DIGITAL 2 (optical): For CD player
AUDIO/VIDEO CONTROL RECEIVER
TUNED STEREO
ANALOG SPK AUTO MUTING SLEEP
DIGITAL AUTO L C R PRO LOGIC ΙΙ DSP H.PHONE VOLUME
INPUT ATT
LINEAR PCM S.WFR LFE
DIGITAL LS S RS
CH-
DVD VCR TV SOUND
ADJUST SETTING
CD TAPE/CDR FM/AM CONTROL
DOWN UP
SOURCE NAME
Source
selecting
CONTROL
buttons
UP 5/DOWN ∞
Remote
NOT
SETTING
CONTROL
DOWN UP
2 CD j 1 TV 2 CDR j
Remote Control
MASTER VOLUME
SETTING
Selecting the Analog or Digital Input
Mode
When you have connected digital source components using both the
analog connection (see page 6) and the digital connection (see page
7) methods, you need to select the input mode correctly.
1
Press one of the source selecting buttons—DVD,
TV SOUND, CD, or TAPE/CDR*—for which you
want to change the input mode.
DVD VCR
CD TAPE/CDR
SOURCE NAME
On the front panel
Note:
* Among the sources listed above, you can select the digital input
only for the sources which you have selected the digital input
terminals for. (See "Setting the Digital Input (DIGITAL IN)
Terminals.")
2
Select digital input mode.
On the front panel:
Press INPUT DIGITAL.
"DIGITAL AUTO" appears on the display
and the indicator for the detected signals also
lights up.
To change the input mode back to analog
input, press INPUT ANALOG.
"ANALOG" appears on the display for a
while.
From the remote control:
Press ANALOG/DIGITAL.
• Each time you press the button, the input mode
alternates between the analog input ("ANALOG")
and the digital input ("DIGITAL AUTO").
TO BE CONTINUED TO THE NEXT PAGE
TV CATV A/V CONTROL
STANDBY/ON
RECEIVER
TEST CENTER AUDIO
1 2 3
EFFECT REAR L
TV/CATV
4 5 6
MENU REAR R
VCR
7/P 8 9
ENTER SUBWOOFER
DVD
10 0 10
RETURN 100
SLEEP
SOUND
PTY–PTY SEARCH–PTY
REW FF
REC PAUSE CD–DISC
Source
TAPE/CDR CD DVD
selecting
ANALOG/
ANALOG
FM/AM TV SOUND VCR /DIGITAL
buttons
DIGITAL
FM MODE FM MODE
ON/OFF
TV/VIDEO SURROUND
MUTING
MODE
VCR CH TV/CATV CH TV VOLUME
VOLUME
REMOTE CONTROL RM - SRX5020J
TV SOUND
TAPE/CDR CD
FM/AM TV SOUND
FM/AM
From the remote control
INPUT DIGITAL
INPUT ANALOG
INPUT ATT
ANALOG
/DIGITAL
DVD
VCR
11