JVC UX-G300 Instructions

Warnings, Cautions and Others
CAUTION: (Standby/on) button!
Disconnect the mains plug to shut the power off completely
(the STANDBY lamp goes off). When installing the apparatus,
ensure that the plug is easily accessible. The
on) button in any position does not disconnect the mains
MICRO COMPONENT SYSTEM
line.
• When the System is on standby, the STANDBY lamp lights
UX-G300
red.
• When the System is turned on, the STANDBY lamp goes
—Consists of CA-UXG300 and SP-UXG300
off.
The power can be remote controlled.
CAUTION:
To reduce the risk of electrical shocks, fire, etc.:
1. Do not remove screws, covers or cabinet.
2. Do not expose this appliance to rain or moisture.
CAUTION:
• Do not block the ventilation openings or holes. (If
the ventilation openings or holes are blocked by a
Thank you for purchasing a JVC product.
newspaper or cloth, etc., the heat may not be able to get
INSTRUCTIONS out.)
• Do not place any naked flame sources, such as lighted
candles, on the apparatus.
GVT0241-015A[US/UN/UB/UG/A/UW]
• When discarding batteries, environmental problems
0108WMKMDWJMM
must be considered and local rules or laws governing
the disposal of these batteries must be followed strictly.
• Do not expose this apparatus to rain, moisture, dripping
©2008 Victor Company of Japan, Limited
or splashing and that no objects filled with liquids, such
as vases, shall be placed on the apparatus.
• Excessive sound pressure from earphones or
headphones can cause hearing loss.
IMPORTANT FOR LASER PRODUCTS
1. CLASS 1 LASER PRODUCT
2. CAUTION: Do not open the top cover or cabinet. There
are no user serviceable parts inside the unit; leave all
servicing to qualified service personnel.
3. CAUTION: Visible and/or invisible class 1M laser radiation
[European Union only]
when open. Do not view directly with optical instruments.
4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED
INSIDE THE UNIT.
Getting Started
Supplied Accessories Connections
After unpacking, check to be sure that you have all the
following items. To connect the FM antenna (supplied)
• Remote control, RM-SUXG300U (× 1) Extend it so that you can obtain the best reception.
• Lithium coin battery CR2025 (× 1)
– The battery has been installed when shipped from the
FM antenna (supplied)
factory.
• AM loop antenna (× 1)
• FM antenna (× 1)
• AC plug adapter (× 1) (not applicable for Hong Kong and
Australia) For better FM reception
If anything is missing, consult your dealer immediately.
Prepare the Remote Control
Disconnect the supplied FM antenna, and connect to
an outdoor FM antenna using a 75 Ω wire with coaxial
When you use the remote control for the first time, pull out
type connector.
the insulation sheet.
Insulation sheet
Rear view
To Replace the Battery in the Remote Control
Lithium coin battery
(product number: CR2025)
NOTES:
• Store the battery in a place where children cannot reach. If
a child accidentally swallows the battery, consult a doctor
immediately.
• To prevent the battery from over-heating, cracking, or starting
a fire:
– Do not recharge, short, disassemble or heat the battery or
dispose of it in a fire.
– Do not leave the battery with other metallic materials.
– Wrap the battery with tape and insulate when throwing
away or saving it.
– Do not poke the battery with tweezers or similar tools.
• Dispose of battery in the proper manner, according to federal,
state, and local regulations.
To a wall outlet
• The batteries (battery pack or batteries installed) shall not be
Plug the AC power cord only after all connections are complete.
exposed to excessive heat source such as sunshine, fire or the
• If the wall outlet does not match the AC plug, use the supplied
like.
AC plug adapter (not applicable for Hong Kong and Australia).
CAUTION:
NOTES:
Danger of explosion if battery is incorrectly replaced.
• Make sure the antenna conductors do not touch any other terminals, connecting cords and power cord. Also, keep the antennas
Replace only with the same or equivalent type.
away from metallic parts of the System, connecting cords, and the AC power cord. This could cause poor reception.
• Make sure both the speakers are connected correctly and firmly.
• When connecting the speaker cords, match the polarity of the speaker terminals: red color to (+) and black color to (–).
• DO NOT connect more than one speaker to each terminal.
• DO NOT allow the conductor of the speaker cords to be in touch with the metallic parts of the System.
CAUTION: Proper Ventilation
To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows:
1. Front: No obstructions and open spacing.
2. Sides/Top/Back: No obstructions should be placed in the areas shown by the dimensions below.
3. Bottom: Place on the level surface. Maintain an adequate air path for ventilation by placing on a stand with a height of
(Standby/
10 cm or more.
Front view
Precautions
Notes on the power cord
• When you are away on travel or otherwise for an extended period of time, remove the plug from the wall outlet.
• When unplugging the System from the wall outlet, always pull the plug, not the power cord.
• Do not handle the power cord with wet hands.
• Disconnect the power cord before cleaning the System or moving the System.
• Do not alter, twist or pull the power cord, or put anything heavy on it, which may cause fire, electric shock, or other accidents.
• If the cord is damaged, consult a dealer and have the power cord replaced with a new one.
Avoid moisture, water, dust, and high temperatures
• Do not place the System in moist or dusty places.
• If water gets inside the System, turn off the power and remove the plug from the wall outlet, then consult your dealer. Using
the System in this state may cause a fire or electrical shock.
• Do not expose the System to direct sunlight or place it near a heating device.
Notes on installation
• Select a place which is level, dry and neither too hot nor too cold—between 5˚C and 35˚C.
• Do not install the System in a place subject to vibrations.
• Do not put heavy objects on the System.
To prevent malfunction or damage of the System
• Do not insert any metallic objects, such as wires, hairpins, coins, etc. into the System.
• Do not block the vents.
There are no user-serviceable parts inside. If anything goes wrong, unplug the power cord and consult your dealer.
1
Do not connect the AC power cord until all other connections have been made.
To connect the AM loop antenna (supplied)
AM loop antenna (supplied)
Turn it until the best reception
is obtained.
Outdoor FM antenna
(not supplied)
To connect the speaker cords
From right
speaker
2
Basic and Common Operations
Side view
How to cancel the demonstration
Press and hold DEMO button while on standby. (Refer to the attached "Information
about the demonstration function.")
Using Headphones
Be sure to turn down the volume before connecting or putting on the headphones.
• Connecting the headphones will deactivate the speakers.
• Sound adjustments also affect the sound through the headphones.
NOTE:
DO NOT turn off (standby) the System with the volume set to an extremely high level;
otherwise, the sudden blast of sound can damage your hearing, speakers and/or
headphones when you turn on the System or start playback.
Playing Back a Disc/USB Mass Storage Class Device
The following operations are explained using the remote control, unless
mentioned otherwise. However, if the System has the same or similar button
names, they can also be used for the operations.
To assemble the AM loop antenna
This System can play back...
– CD.
– CD-R/CD-RW recorded in audio CD format (CD-DA) or recorded MP3/WMA files
in ISO 9660 format.
– USB mass storage class device containing MP3/WMA files.
• When playing back an MP3 or WMA track, MP3 or WMA indicator lights up.
Loading a Disc
(on the System only)
1 Press to open the disc tray.
2 • When using an 8 cm disc, place it on the inner
circle of the disc tray.
3 Press to close the disc tray.
Connecting a USB Mass Storage Class Device
You can connect a USB mass storage class device such as a USB flash memory
Press and hold
device, MP3 player, multimedia card reader, etc. to the System.
Front view
USB cable (not supplied)
Release
Insert
NOTES:
• When connecting with a USB cable, use the USB 2.0 cable whose length is less than
Red
1 m.
• USB mass storage class device is charged through the USB MEMORY terminal when
the System is turned on and the source is "USB."
• You cannot connect a computer to the USB MEMORY terminal of the System.
• Do not disconnect the USB mass storage class device when the System is turned on. It
may cause malfunction of both this System and the device.
• Noise and static electricity may stop the USB mass storage class device sound. In this
case, disconnect and connect the USB mass storage class device again after turning
From left
Black
off the System.
speaker
Prohibiting Disc Ejection
(on the System only)
You can lock the disc tray so that no one can eject the loaded disc.
• This is possible while the System is on standby.
To cancel the prohibition, repeat the same procedure.
+
Point at the remote sensor on the front panel.
(The operating range is approx. 7 m.)
STANDBY lamp
PHONES jack
Stereo mini plug cord
3
Basic Disc/USB Mass Storage Class Device Operations
To Press Indication/Result
Play back the disc • Current track number and elapsed playing
time appear.
For MP3/WMA files: Before current track
Play back the USB
number and elapsed playing time appear, the
mass storage class
tag information appears if it is recorded.
device
• During playback, press again to pause.
Stop playback • While playback is stopped, total track number
and total playing time (for MP3/WMA files,
group number and track number) appear.
Select a track Select the next tracks.
To go back to the beginning of the current or
previous tracks.
Select a group Select the next groups.
(MP3/WMA only)
Select the previous groups.
Forward search/ Press and hold to fast-forward the track during
Reverse search playback.
To stop searching, release the button.
Press and hold to fast-reverse the track during
playback.
To stop searching, release the button.
NOTES:
• If no disc is inserted or no USB mass storage class device is connected, "NO DISC" or
"NO USB" appears on the main display.
• If MP3/WMA files are not recorded on the disc or in the USB mass storage class device,
"NO PLAY" appears on the main display.
RESUME Play (For MP3/WMA only)
When you stop the playback by one of the following operations, this System
stores the beginning of the stopped track on the disc or USB mass storage class
device.
– Pressing 7 once
– Changing the source
When you start playback again, playback starts from the stored position.
To clear the stored position, open the disc tray or disconnect the USB mass
storage class device.
• When you clear the stored position and start playback, playback starts from the
beginning of the first track
NOTE:
This function does not work in Program Play and Random Play.
4
Press
To Indication/Result
System Remote
Turn on or off The STANDBY lamp on the System turns off/on.
(standby) the power
Select a source See "Playing Back a Disc/USB Mass Storage Class
Device" on page 4.
Press repeatedly to select "FM" or "AM."
• For "FM/AM," see "Listening to FM and AM
Broadcasts" on page 5.
See "Listening to Digital Audio Player" on page 5.
Adjust the volume Adjustable range: Level 0 ("VOL MIN") to level 40
("VOL MAX").
Drop the volume in a To restore the volume, press again, or adjust the
—
moment volume level.
Activate the EALA The indicator lights up.
surround mode — To cancel this function, press repeatedly until
indicator lights off.
Emphasize the The S.TURBO indicator lights up.
sound (Sound Turbo To cancel this function, press again.
function)
Reinforce the bass Press and hold until the AHB indicator lights up.
sound (Active Hyper • When Sound Turbo function is activated (see
Bass Pro function) — above), this function cannot be activated.
To cancel this function, press and hold again when
Sound Turbo function is deactivated.
Adjust the tone (Bass/ Press once for adjusting the bass level; twice for treble
Treble) level, then, press VOLUME +/–.
Adjustable range: –3 to +3.
—
Change the display Press when the System is turned on.
brightness — To cancel this function, press again.
Change the display For setting the clock, see "Setting the Clock and Using
information (Clock and — Timers" on page 6.
Source)
Set the Save Mode Press when the System is on standby.
Setting the save mode allows you to reduce power
consumption by turning the display off while on
—
standby.
To cancel this function, press again when the System
is on standby.
Playing Repeatedly—Repeat Play
1 Press repeatedly to specify the repeat mode as follows:
REP TRK: Repeats the current (or specified) track. [ ]
REP GRP: Repeats all tracks in the current group (MP3/WMA
only). [ ]
REP ALL: Repeats all tracks. [ ALL ]
REP OFF: Normal playback
2
or
Programming the Playing Order—Program Play
1 During stops, press until the PRGM (program) indicator lights
up before playing.
2 • For MP3/WMA files: Select a group number, then a track
number.
or
• For CD: Select a track number.
3 Press to program the selected group/track.
4 Repeat steps 2 and 3 to program other tracks you want.
• If you try to program a 51st track, "FULL" will appear.
5 The tracks are played back in the programmed order.
Operations for Program Play (while not playing)
• To check the programmed contents, press 4 or ¢.
• To add tracks, repeat steps 2 and 3 above.
• To erase the last programmed track, press CANCEL.
• To erase the entire program, press and hold CANCEL for about 2 seconds.
• To exit from program play, press MODE.
– The stored program is kept.
Playing at Random—Random Play
1 Press until the RND (random) indicator lights up before you start
playback.
2 Playback starts in random order.
or
Random Play ends when all tracks are played back.
Operations for Random Play
• To skip a track, press ¢.
• To go back to the beginning of the current track, press 4.
• To exit from random play, press MODE while playback is stopped.