Adjusting Dsp Modes - JVC TH-A5R Instructions Manual

5
To adjust the output level for the center speaker,
the rear speakers, and the subwoofer
1) Press SOUND repeatedly to select the
"CEN," "REAR," or "SW."
• Each time you press the button, the indication on
the display changes as follows:
00 F 00
Normal indication
(canceled)
CEN (Center) : To adjust the output level for center
speaker (from –06 dB to +06 dB).
REAR : To adjust the output level for rear
speakers (from –06 dB to +06 dB).
SW (Subwoofer) : To adjust the output level for subwoofer
(from –06 dB to +06 dB).
• When selecting "3 STEREO," you cannot adjust the output
levels for the rear speakers and subwoofer.
• "CEN –06dB," "REAR –06dB," and "SW –06dB" are the
initial settings. If you have already changed the settings,
another value will appear.
2) Press 3 or 2 to adjust the
output level.
3 : Increases the output level.
2 : Decreases the output level.
3) Repeat 1) and 2) for setting
the other speakers.

Adjusting DSP Modes

You can adjust the following settings while activating DSP modes.
It is recommended that you make adjustments from your actual
listening point while listening to reproduced sounds.
– Output balance for the front speakers
– Output balance for the rear speakers
– Output level for the rear speakers
– Output level for the subwoofer
– Overall level of DSP effect
• DSP modes cannot be used with Dolby Surround. Once one of
DSP modes is activated, Dolby Surround in use will be canceled.
• When you play back a DVD encoded with Dolby Digital or DTS
Digital Surround, DSP MODE button (or DSP button on the center
unit) does not work.
Before you start, remember...
• Make sure that you have set the speaker information correctly
(see page 16). You cannot adjust the speaker output balance
and levels when you have set the speaker settings to "NONE."
• There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 2 again.
SOUND
00 R 00 CEN
SW REAR
ENTER
1
Select and play any source except Dolby Digital
or DTS Digital Surround.
2
Press DSP MODE (or DSP on the front
panel) repeatedly to select the desired
DSP mode.
The DSP indicator lights up on the display while the DSP modes
are activated.
• Each time you press the button, DSP mode changes as follows:
HALL THEATER
Normal
LIVE CLUB
indication
(canceled)
Now, you are ready to start the adjustment.
• To adjust the output balance for the front speakers and the rear
speakers, go to the next step.
• To adjust the output level for the rear speakers, go to step
next page.
• To adjust the overall level of DSP effect, go to step
page.
3
To adjust the output balance for the front
speakers and the rear speakers
1) Press SOUND repeatedly until one of
the following adjustment indications
appears on the display.
• Each time you press the button, the indication on the
display changes as follows:
00 F 00
Normal
REVERB
indication
(canceled)
00 F (Front) 00 : To adjust the output balance for the front
speakers.
00 R (Rear) 00 : To adjust the output balance for the rear
speakers.
• "00 F 00" and "00 R 00" are the initial setting (the output
balances are at the center position). If you have already
changed the setting, another value will appear.
2) Press 3 or 2 to adjust the
output balance.
3 : Decreases the left speaker
output, or restores the right
speaker output.
2 : Decreases the right speaker
output, or restores the left
speaker output.
• Each output balance changes from
OFF (silence), –06 (most reduction) to 00 (no reduction).
3) Repeat 1) and 2) for setting the other speaker.
TO BE CONTINUED ON THE NEXT PAGE
DSP MODE
PAVILION
DANCE CLUB
4
on the
5
on the next
SOUND
00 R 00 REAR
LIVE ROOM
ENTER
23