NEO P2AUDV1 Installation Manual & User Manual

Optional Remote Kit: Functions for iPod
iPod:
iPod: Repeat one / Repeat all / Repeat
off
iPod: Next Track
iPod: Previous Track
1
iPod: Skip to the next PLAYLIST
4
iPod: Skip to the previous PLAYLIST
6
Vehicle BUS Connector - P2AUDV1 Connector
You can access the CD changer connector located on the back of the radio. Unplug the factory connection
if present and plug the P2AUDV1 connector into the receptacle. The connector should securely lock.
Ground wire MUST be connected to a stable grounding point.
To factory harness
in vehicle
P2AUDV1 Connector
P2AVWV1 - R2 Connector Modification
below is required. NOTE: some
2 4 Remove the SAT wires from
Disconnect main radio Slide out the inner part of
the factory
harness and locate SAT the SAT connecor from
releasing the pins with a small
connector. Remove it plastic housing.
screw driver or ball point pen.
from main harness by
pressing on the release
tab of the SAT connector.
pins 1,3, 7
5 Relocate wires to
3 Disassemble the ProLink
P 2 A V W V 1 R2 connector keeping
P2AVWV1 R2 connector the
the same order and location.
same way as the factory
SAT connector.
SAT
pins 1,3, 7
Connector
1
Toggle the auido sources between iPod
SOURCE
and SIRIUS/AUX
Play / Pause
3
iPod: Skip to the next ALBUM
6
iPod: Skip to the previous ALBUM
* ARTIST is currently not supported
NEO logo is a trademark of NEO Car Audio, Inc. SiriusConnect, Sirius and XM logos are trademark of SiriusXM. The Made for iPod logo is a trademark of Apple Inc. Apple iPod is not included in the package. For our detailed
terms and conditions please visit our website at www.neocaraudio.com.
5
Installation
1. Verify compatibility
2. Disconnect battery
3. Remove radio from car
To ground
To ProLink
Interface Module
4. Install ProLink cable
12 to 16 pin adapter
Some radios will enter an anti-theft security mode and will lock requiring the radio's security code
to be entered to unlock it. This code can be requested from the vehicle's dealership.
7
Vehicle BUS Connector - P2AVWV1 R2 Connector
You can access the CD changer connector located on the back of the radio. Unplug the factory connection if
present and plug the P2AVWV1 R2 connector into the receptacle. The connector should securely lock.
Ground wire MUST be connected to a stable grounding point.
6 Put plastic connector covers
connector by back on. Insert the
P2AVWV1 R2 connector to
factory VW main harness.
P2AVWV1
R2 connector
7 Connect ground wire to
chassis of radio.
for selected Audi/VW vehicles
P2AUDV1, P2AVWV1, P2AVWTV1
Installation Guide/User manual
5. Route kit to glove box or other accessible location
6. Connect battery & test
7. Complete install by re-installing radio
12 to 16 pin adapter
P2AVWV1 R2 connector
Identifying your ProLink kit
ProLink kit
contents
P2AUDV1, P2AVWV1, P2AVWTV1 - These
kits work in CDC Emulation mode.
NEO interface for iPod
Installation Guide/User Manual
user manual
ProLink module
Only one of these cables will be included with your kit
iPod docking
P2AUDV1 P2AVWV1
cable
ProLink-AVW rev 091311 connector R1 connector
4
Connection Diagram
SIRIUS SAT radio
(not included)
Note: works with
P2AVWSV1 only!
ProLink module
Vehicle BUS
(front)
connector
SIRIUS connector*
AUX connector
IR receiver
(optional)
*Do not connect the iPod dock cable under any circumstance to the SIRIUS module connector!
Improper connection can cause permanent damage to iPod/SIRIUS module.
8
Vehicle BUS Connector - P2AVWV1 R1 Connector
You can acces the CD changer connector located on the back of the radio. Unplug the factory connection if
present and plug the P2AVWV1 R1 connector into the receptacle. The connector should securely lock.
Ground wire MUST be connected to a stable grounding point.
P2AVWV1 R1 connector
To ProLink
Interface Module
3
XXX- XXX-XXX Product part number
Module serial number
NBM12345678
12 to 16 pin
P2AVWV1 P2AVWTV1
adapter
R2 connector connector
Auxiliary device iPod/iPhone
ProLink module
(not included)
(not included)
(back)
Update port
iPod dock cable*
(USB to PC)
(optional)
See back for more
9
To ProLink
Interface Module
12 to 16 pin adapter