Tonneau
chevy silverado,
gmc sierra 1999 – current (12 pages)
Summary of Contents for UnderCover 2110
Page 1
TONNEAU INSTALLATION GUIDE Warranty, Care & Maintenance Model 2110 Ford Explorer Sport Trac 2007-Current EASY AS 1-2-3! NORMAL INSTALLATION TIME MINUTES For Warranty Issues, Contact UnderCover Directly FORM # IG2110HH Modified Mar 2009 (866) 900-8800 www.undercoverinfo.com...
Page 2
Be sure to use only cleaners, waxes, etc., which are labeled ‘Safe for Plastics’ . Make sure that chemicals or substances, which are not labeled ‘safe for plastics’ , do not come in contact with your Undercover. Failure to do so could cause discoloration and/or structural damage to your Undercover and will void your warranty.
Page 3
Page 2 Model 2110 Ford Explorer Sport Trac 2007-Current Note: If your Tonneau has already been installed, skip to Page 11 for removal and reinstallation instructions. FORM # IG2110HH Modified Mar 2009...
Page 4
Page 3 Model 2110 Ford Explorer Sport Trac 2007-Current FACT: UnderCover is the lightest hardshell tonneau in the industry. Only 58-pounds for full size trucks. Installing your Ford Sport Trac hardware is simple and easy to do. The Sport Trac comes with the mounting holes already in place.
Page 5
Page 4 Model 2110 Ford Explorer Sport Trac 2007-Current FORM # IG2110HH Modified Mar 2009...
Page 6
OVER TIGHTEN. DOING SO CAN SHEAR OFF THE BALL STUD AND CAUSE SERIOUS DIFFICULTY CORRECTING. Once you UnderCover is installed you will be able to lift the cover up and clip the strut to the ball mount. See Page 6, Picture C.
Page 7
Page 6 Model 2110 Ford Explorer Sport Trac 2007-Current FORM # IG2110HH Modified Mar 2009...
Page 8
Page 7 Model 2110 Ford Explorer Sport Trac 2007-Current FACT: UnderCover's ABS-Composite material makes it the strongest and most durable tonneau on the market. Installation of the front bracket is very similar to the rear. Remove the plastic plugs exposing the 3 preset bolt holes located at the front of the bed.
Page 9
Page 8 Model 2110 Ford Explorer Sport Trac 2007-Current FORM # IG2110HH Modified Mar 2009...
Page 10
Page 9 Model 2110 Ford Explorer Sport Trac 2007-Current FORM # IG2110HH Modified Mar 2009...
Page 11
Page 10 Model 2110 Ford Explorer Sport Trac 2007-Current Not all truck beds are assembled 100% square, so it may be necessary to do some preliminary adjustments. The mounting holes in the front brackets are slotted to allow for adjustment.
Page 12
Page 11 Model 2110 Ford Explorer Sport Trac 2007-Current FACT: In less than one minute, you can both take on and off the Undercover tonneau. Fastest removal system in the industry. Install hydraulic struts making sure LARGE end of strut is attached to the tonneau, and SMALL or rod end is attached to the ball stud on rear bracket Page 10, Figure 7, Picture A.
Page 13
Page 12 Model 2110 Ford Explorer Sport Trac 2007-Current FORM # IG2110HH Modified Mar 2009...
Page 14
Page 13 Model 2110 Ford Explorer Sport Trac 2007-Current Congratulations! Your 30-minute installation job is now complete. Now, in less than one minute, you will be able to put on and take off your tonneau cover. STEP 1 Release strut off of ball stud Picture B.
Page 15
Page 14 Model 2110 Ford Explorer Sport Trac 2007-Current Prior to removing the STEP 1 tonneau, mount the two J-Hooks provided on the garage wall. The hooks must have a minimum height from the floor of 84", and be 32” on center horizontally apart Picture A &...
Page 16
Page 15 Model 2110 Ford Explorer Sport Trac 2007-Current...