Honeywell HB273 Quick Installation Manual

Performance Series
HB273(X) Super High Resolution VFAI True
Day/Night IR Indoor/Outdoor Bullet Camera
Quick Installation Guide

1. Warnings and Cautions

WARNING Installation and servicing should be performed
only by qualified and experienced technicians to conform to all
local codes and to maintain your warranty.
WARNING 24 V AC/12 V DC cameras require the use of
CSA Certified/UL Listed Class 2 power adapters to ensure
compliance with electrical safety standards.
WARNING This device is configured for 24 V AC or 12 V
DC operation. Do not connect to a higher voltage. Use only with
NRTL-approved Class 2 power supplies.
CAUTION The light emitted from the near-infrared light emitting
diodes (LEDs) provide illumination over a wide area. This light is not
considered a risk to the unshielded human eye. However, as with any
light source, it is recommended that normal precautions be taken to
avoid unnecessary exposure. For example, avoid staring into the beam or
viewing the LEDs directly with optical instruments at close range.
Note IR LEDs may be warm after prolonged use.
800-11940V1 - A - 10/2012
CAUTION
RISK OF ELECTRIC
SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE THE COVER.
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
Regulatory Statements
Information to the user: This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at his own expense.
Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la Classe A est conforme à la norme NMB-003 du Canada.
Manufacturer's Declaration of Conformance
The manufacturer declares that the equipment supplied with this guide is compliant with the
essential requirements of the EMC directive 2005/108/EC and the General Product Safety
Directive (GPSD) 2001/95/EC, conforming to the requirements of standards 55022 for
emissions, EN 50130-4 for Immunity, and EN 60065 for Electrical Equipment safety.

2. Important Safety Instructions

• Read and keep these instructions.
• Please ensure that your installation area can safely support the weight of
the camera.
• Do not install the camera in extreme temperature conditions. Only use
the camera where temperatures are within the limits shown in the
specifications section of the guide. Be especially careful to provide
ventilation when operating under high temperatures.
• Do not aim the camera toward an extreme light source to prevent
damage to the CCD.
• Do not touch the camera lens, dome, or bezel (front glass plate).
• Do not drop the camera or subject it to physical shock.
• Do not use a strong or abrasive detergent when cleaning the camera.
Warranty and Service
Subject to the terms and conditions listed on the Product warranty, during the warranty
period Honeywell will repair or replace, at its sole option, free of charge, any defective
product returned prepaid.
In the event you have a problem with any Honeywell product, please call Customer Service
at 1.800.323.4576 for assistance or to request a Return Merchandise Authorization (RMA)
number.
Be sure to have the model number, serial number, and the nature of the problem available
for the technical service representative.
Prior authorization must be obtained for all returns, exchanges, or credits. Items shipped
to Honeywell without a clearly identified Return Merchandise Authorization (RMA)
number may be refused.
Note The manufacturer is not responsible for any damage caused by improper use
of the product or failure to follow instructions for the product.
THIS SYMBOL INDICATES THAT
DANGEROUS VOLTAGE
CONSTITUTING A RISK OF
ELECTRIC SHOCK IS PRESENT
WITHIN THE UNIT.
THIS SYMBOL INDICATES THAT
IMPORTANT OPERATING AND•
MAINTENANCE INSTRUCTIONS
ACCOMPANY THIS UNIT.
800-11940V1 - A - 10/2012